Instructions: Page 1 1) Install the heat post with shield and debowler into round safety stand 2) Plug the Enail coil and power cord into the rear of

Transcription

1 Instructions: Page 1 1) Install the heat post with shield and debowler into round safety stand 2) Plug the Enail coil and power cord into the rear of the PID controller 3) Install the flowerpot head (showerhead, wraparound or Vrod) into the coil cover. Slide both onto the 20mm coil and secure with Coil Nut. (procedure varies for vrod). 4) Place the Flowerpot head onto the Heat post on the safety stand. 5) Turn on the rear power switch. 6) Using the up and down arrows only set heat to 700 deg. (the set and > buttons are only used for advanced programming). The PID controller will retain the last programmed temp when powered off and on. 7) Press the push button on the front of the PID controller to energize the coil. Warning the coil will heat up very quickly so make sure it s placed securely on the safety stand and avoid contact with the head. 8) After the Controller aka pid reaches the programmed temp it s important to wait an additional 60 sec for the heat to soak thoroughly thru the head. Normal heat up time is 3 min. 9) Fill glass to the middle of the top perk. 10) Install 18mm post into the Glass 18mm joint. 11) Install a titanium screen into the bowl. 12) Slide the bowl down to rest on top of the glass. 13) Using a paper clip tighten the bowl to the post with the handle. 14) Start by loading a small amount of flower ( Gram) barely cover the screen. 15) Enjoy

2 Getting to know your Flowerpot Unlike other vaporizers the flowerpot is highly adjustable. This infinite adjustability may seem complicated at first but ultimately it will result in a vaporizer experience unlike any other. The following are some of the variables to consider when getting your flowerpot dialed in to your personal preference. Fine grind will increase the surface area of the material and produce denser vapor. Draw strength is a very important factor. The faster the air moves thru the flowerpot s head the cooler the air will be when it contacts the flower. This can be compensated by adjusting the temp of the pid Controller. 25deg increments is recommended. A slow draw will cause the material to over cook. Some people prefer using the carb cap for flower as this provides additional control. The amount of time allowed for heat soak will determine the amount of heat that is absorbed into the head. This will vary results. it s advised to select a heat up time and stick with it during your earning period. The best flavors are found when using lower temps. Start low and increase 25 deg. each session. Remember adjusting the temp will require 2-3 min. to normalize.

3 Getting to know your Flowerpot Continued. Every glass rig is a little different. Don t make the mistake and plan on using a your friend s rig at the party without first using it and learning the correct settings for that specific rig. When using the Flowerpot in group settings it s best to set the temp low and use the carb cap to compensate UP for users slow draw strength. Sooner or later everyone has a combustion event and this temporary ruins the clean taste of their flowerpot. The fix is to clean the glass and titanium with Isopropyl alcohol. Depending on the severity a light torching of the titanium may be required. To maintain a clean taste always swab the dish after every dab with a q- tip. Never use any metal other than titanium for scraping the dish clean. Using a screw driver or knife will leave lead deposits on the dish and cause rusting. The SIC dish may become stuck (glued with resin) into the wraparound head. Soak the two parts in alcohol to loosen. Try a convection dab by adding your concentrate on top of the double wave screen.

4 Getting to know your Flowerpot Continued. Try roasting a Full Nug then break apart to finish. Use a 14mm size rig if draw resistance is desired with the Showerhead. Use your AVB for edibles (already vaped bud) Video below FlowerPot Assembly Instructions Video. Flowerpot Forum Exchange Advanced Techniques on www. F**k Combustion. Here s a video of how to use your AVB (already vaped bud) for some delicious edibles

5 NewVape Twax Bundle Quality Control Check List Flowerpot Round Stand Base FlowerPot De-bowler Spike FlowerPot Heater Coil Post ShowerHead mm Coil Nut Coil Cover Vrod Head 3129 Shovelhead bowl or Panhead bowl Large Base Rig 9110 Stero Matrix 9301 Straight Tube " Case with NV Badge and Custom Foam Showercap Carb Cap with 4" scoop dabber Arm Band Fine Grinder Threaded Loading Tool with Black Silicone Enail Controller Black or Gold mm Coil Coil Cover Enail Handle pack Beamer Ti Screen Aluminum Storage Container WrapAround Head SiC Dish Enail Power Cord Titanium Material Certificate Instructions Preset Controller to 650 deg Thread Check with Gages Glue Badge and Foam Order Number Inspected and Packaged by

6 Thank you for Shopping with NewVape