SECTION DOMESTIC WATER PIPING SYSTEMS. 0. Pipe and pipe fittings are specified in the following sections:

Transcription

1 SECTION January 7, 2004 DOMESTIC WATER PIPING SYSTEMS. RELATED SECTIONS 0. Pipe and pipe fittings are specified in the following sections:. Section 15061, STEEL PIPE AND FITTINGS.. Section 15062, COPPER AND COPPER ALLOY PIPE AND FITTINGS.. Section 15064, DUCTILE IRON PIPE AND FITTINGS. 0. Valves are specified in the following sections:. Section 15101, GATE VALVES.. Section 15103, BALL VALVES.. Section 15106, CHECK VALVES.. Section 15110, SERVICE DRAINS. 0. Strainers are specified in Section 15123, PIPELINE STRAINERS. 0. Pipe labels and valve tags are specified in Section 15190, IDENTIFICATION SYSTEMS.. PIPE AND FITTINGS 0. Pipe and fittings (2 inches and smaller) above grade shall be copper, System Type C Pipe and fittings (2-1/2 inches and larger) above grade shall be copper, System Type C-2. **OR** 2. Pipe and fittings (2-1/2 inches and larger) above grade shall be steel, System Type S Pipe and fittings (2 inches and smaller) below grade shall be copper, System Type C Pipe and fittings (2-1/2 inches and larger) below grade shall be ductile iron, System Type DI-1 or DI- 2, at the Contractor's option. B. VALVES 0. Isolation valves at equipment (2 inches and smaller) shall be ball valves, Valve Type B Isolation valves at equipment (2-1/2 inches and larger) shall be gate valves, Valve Type GT Isolation valves in piping runs (2 inches and smaller) except at building entrance, shall be ball valves, Valve Type B Isolation valves in piping runs (2-1/2 inches and larger) except at building entrance, shall be gate valves, Valve Type GT Check valves at pump discharges (2 inches and smaller) shall be Valve Type C Check valves at pump discharges (2-1/2 inches and larger) shall be Valve Type C Check valves for general use (2 inches and smaller) shall be Valve Type C Check valves for general use (2-1/2 inches and larger) shall be Valve Type C Drain valves shall be boiler drains, Valve Type SD Strainer blow-down valves shall be ball valves, Valve Type B-1. DIVISION SECTION 15411

2 B. STRAINERS January 7, Strainers (2 inches and smaller) shall be Strainer Type ST Strainers (2-1/2 inches and larger) shall be Strainer Type ST-3. DIVISION SECTION 15411

3 SECTION January 7, 2004 DRAIN, WASTE, AND VENT PIPING SYSTEMS. RELATED SECTIONS 1. Pipe and pipe fittings are specified in the following sections:. Section 15062, COPPER AND COPPER ALLOY PIPE AND FITTINGS.. Section 15063, CAST IRON PIPE AND FITTINGS. b. Section 15066, PLASTIC PIPE AND FITTINGS. 2. Pipe labels are specified in Section 15190, IDENTIFICATION SYSTEM.. PIPE AND FITTINGS 0. Sanitary waste and vent pipe and fittings, above grade, shall be either copper, System Type C-4, or cast iron, System Type CI-3, at the Contractor's option. 0. Sanitary waste pipe and fittings within 5 feet of a urinal shall be cast iron regardless of the option chosen for the main system. 0. Pump discharge pipe and fittings, from the pump discharge connection to the first gravity drain line 4 inches in size or larger, shall be copper regardless of the option chosen for the main system. 0. Sanitary waste and vent pipe and fittings, below grade, shall be cast iron, either System Type CI-1 or System Type CI-2, at the Contractor's option. 0. Storm drainage pipe and fittings, above grade, shall be cast iron, System Type CI Storm drainage pipe and fittings, below grade, shall be cast iron, either System Type CI-1 or System Type CI-2, at the Contractor's option. 0. Acid waste and vent pipe and fittings shall be plastic, System Type P Air conditioning unit condensate drainage pipe and fittings shall be plastic, System Type P-6. **OR ** 8. Air conditioning unit condensate drainage pipe and fittings shall be copper, System Type C Indirect waste pipe and fittings shall be copper, System Type C-6. DIVISION SECTION 15412

4 January 7, 2004 SECTION INDUSTRIAL GAS PIPING SYSTEMS. RELATED SECTIONS 1. Pipe and pipe fittings are specified in the following sections:. Section 15061, STEEL PIPE AND FITTINGS. 2. Valves are specified in the following sections: a. Section 15103, BALL VALVES. b. Section 15104, BUTTERFLY VALVE. 3. Strainers are specified in Section 15123, PIPELINE STRAINERS. 3. Pipe labels and valve tags are specified in Section 15190, IDENTIFICATION SYSTEMS.. LOW PRESSURE SYSTEMS: 0. This section applies to the following low pressure systems:. Argon (0-150 PSIG).. Carbon Dioxide (1-150 PSIG). Nitrogen (0-150 PSIG).. Oxygen (0-150 PSIG).. Compressed Air (0-125 PSIG). 0. PIPE AND FITTINGS 0. VALVES. Pipe and fittings (2 inches and smaller) above grade shall be steel, System Type S-1 with malleable iron fittings.. Pipe and fittings (2-1/2 inches and larger) above grade shall be steel, System Type S-4 or S- 7, at the Contractor's option.. Except for compressed air service isolation valves (2 inches and smaller) shall be ball valves, Valve Type B-1.. Isolation valves (2 inches and smaller) for compressed air service shall be offset ball valves, with integral bleed, as manufactured by Bowes Manufacturing Inc.. Isolation valves at equipment (2-1/2 inches and larger) shall be butterfly valves, Valve Type BF-2.. Isolation valves in piping runs (2-1/2 inches and larger) shall be butterfly valves, Valve Type BF STRAINERS. Strainers (2 inches and smaller) shall be Strainer Type ST-1.. Strainers (2-1/2 inches and larger) shall be Strainer Type ST-4.. HIGH PRESSURE SYTEMS: 0. This section applies to the following high pressure systems:. Compressed Air (150 4,500 PSIG) DIVISION SECTION 15413

5 . Nitrogen (150 3,100 PSIG) January 7, 2004 DIVISION SECTION 15413

6 PIPE AND FITTINGS January 7, Pipe and fittings shall be steel, System Type S-11. DIVISION SECTION 15413

7 SECTION June 13, 2003 FUEL GAS PIPING SYSTEMS. QUALITY ASSURANCE 0. Installation of underground natural gas piping shall be in full conformance with the requirements of the local utility and by personnel whose training and qualifications have been approved by the local utility. 0. The entire fuel gas system, including the pressure reducing station and all piping, shall be installed in strict conformance with National Fire Protection Association (NFPA) Publication NFPA 54; National Fuel Gas Code.. RELATED SECTIONS 0. Pipe and pipe fittings are specified in the following sections:. Section 15061, STEEL PIPE AND FITTINGS. 0. Valves are specified in the following sections:. Section 15103, BALL VALVES.. Section 15104, BUTTERFLY VALVES.. Section 15105, LUBRICATED PLUG COCKS AND VALVES. 0. Pipe labels and valve tags are specified in Section 15190, IDENTIFICATION SYSTEMS. B. SYSTEMS 0. This section specifically covers the following piping systems: B. PIPE AND FITTINGS. Natural Gas (0-150 PSIG).. Propane (0-150 PSIG).. Hydrogen (0-15 PSIG). 0. Supply pipe and fittings (2 inches and smaller) above grade shall be steel, System Type S Supply pipe and fittings (2-1/2 inches and larger) above grade shall be steel, System Type S Vent piping and fittings shall be steel, System Type S-8. B. VALVES 0. Isolation valves shall be one of the following, at the Contractor's option:. Ball Valves: Valve Type B-5.. Lubricated Plug Valves: Valve Type LP-1.. Butterfly Valves: Valve Type BF-6. DIVISION SECTION 15416

8 SECTION June 13, 2003 SHOCK ABSORBERS. ACCEPTABLE MANUFACTURERS 0. Jay R. Smith Manufacturing Company. 0. Precision Plumbing Products, Inc. 0. Josam Manufacturing Company. 0. Or as approved.. SHOCK ABSORBERS 0. Shock absorbers shall meet or exceed all performance requirements set forth in Standard P.D.I. WH Shock absorbers shall be of the hydropneumatic type with system operating pressure acting against a compressible gas through either a flexible bellows or an isolating piston. 0. Pistons, if used, shall be of brass construction and shall be fitted with lubricated O-ring seals to ensure integrity of the gas cushion. 0. Shock absorber shells shall be of stainless steel or hard drawn copper construction and shall be fitted with a screwed system connection. 0. Shock absorbers shall be Jay R. Smith Hydrotrol, or as approved. DIVISION SECTION 15421

9 SECTION June 13, 2003 HOSE BIBBS. ACCEPTABLE MANUFACTURERS 0. Woodford Manufacturing Company. 0. Chicago Faucet Company. 0. Acorn Engineering Company. 0. Or as approved.. HOSE BIBBS FOR FINISHED SPACES 0. Hose bibbs shall be of the bronze body, wall-mounted type with wall flange, 1/2 inch screwed inlet, 3/4 inch hose thread outlet, integral vacuum breaker, adjustable packing nut, screwed bonnet, replaceable composition disc or cartridge, and chrome finish. 0. Hose bibbs shall be supplied with loose key operating handles. 0. Hose bibbs shall be Woodford Model 24P-1/2, or as approved.. HOSE BIBBS FOR UNFINISHED SPACES 0. Hose bibbs shall be of the bronze body, pipe-mounted type with 1/2 inch solder joint inlet, 3/4 inch hose thread outlet, integral vacuum breaker, adjustable packing nut, screwed bonnet, replaceable composition disc or cartridge, and rough brass finish. 0. Hose bibbs shall be supplied with a wheel type operating handle. 0. Hose bibbs shall be Woodford Model 24CP, or as approved. DIVISION SECTION 15424

10 SECTION June 13, 2003 FIXED AIR GAPS B. ACCEPTABLE MANUFACTURERS 2. Jay R. Smith Manufacturing Company. 2. Zurn Industries, Incorporated. 2. Josam Manufacturing Company. 2. Wade Division, Tyler Pipe. 2. Or as approved. B. AIR GAPS 2. Fixed air gaps shall be of cast construction, shall be designed to minimize splashing, shall allow for vertical adjustment of the inlet pipe, and shall have provisions for securely holding the inlet pipe in position once adjusted. 2. Air gaps for water supply piping shall be of bronze construction with a female threaded outlet and shall be Jay R. Smith Figure 3950, or as approved. 2. Air gaps for waste lines shall be of cast iron construction with a no-hub or spigot outlet, as applicable, and shall be Jay R. Smith Figure 3955, or as approved. DIVISION SECTION 15425

11 June 13, 2003 SECTION DOMESTIC HOT WATER REGULATORS A. ACCEPTABLE MANUFACTURERS 2. MCC Powers Process Controls. 2. Symmons Industries Incorporated. 2. Or as approved. A. HOT WATER REGULATORS 2. Hot water regulators shall be of the thermostatic mixing type utilizing a liquid-filled thermostatic element. 2. Valve shall have an adjustable discharge (mixed) water temperature range from 85 degrees F to 160 degrees F and shall automatically compensate for inlet temperature variations to maintain the discharge temperature within 3 degrees F of the set point. 2. Valve shall be of brass construction with rough brass finish and shall utilize balanced, independently seated hot and cold water valves to automatically compensate for pressure fluctuations. 2. The design of the regulator shall provide for automatic shutoff of the discharge water in the event of loss in pressure on either inlet and in the event of thermostatic element failure. 2. Hot water regulators shall include a combination strainer-shutoff- check valve on each inlet connection. Inlets shall be of the union type and shall allow for variations in supply and discharge piping relationships. 2. Hot water regulators shall be Powers Series 430 Hydroguard, or as approved. DIVISION SECTION 15426

12 June 13, 2003 SECTION PRESSURE CONTROL DEVICES FOR DOMESTIC WATER SYSTEMS A. SELF-CONTAINED PRESSURE REDUCING VALVES 0. Acceptable Manufacturers. Watts Regulator Company.. A.W. Cash Valve Manufacturing Company.. Or as approved. 0. Construction Details. Reducing valves shall be of the spring-loaded diaphragm type with renewable seat and disc.. Discharge pressure shall be field adjustable, and valve shall be suitable for dead end service.. Valves shall be of bronze body construction with a sealed spring cage and threaded end connections.. Valves shall be suitable for inlet pressures to 250 psig and water temperatures to 160 degrees F. 0. Standard of Quality. Self-contained pressure reducing valves shall be Watts No. 223, or as approved. A. PILOT-OPERATED PRESSURE REDUCING VALVES 0. Acceptable Manufacturers. Watts Regulator Company. 0. Construction Details. Reducing valves shall be the hydraulically-operated diaphragm type with an adjustable external pilot valve.. Main valve shall be of the single seated, globe pattern, packless construction type with renewable seat and fully guided stem.. Main valve shall be of cast iron construction with bronze trim and flanged end connections, and shall be provided with a fused epoxy coating on all ferrous surfaces (internal and external).. Main valve shall be suitable for inlet pressures to 125 psig and water temperatures to 160 degrees F.. Pilot valve shall be of the spring-loaded diaphragm type with renewable seat and disc.. Pilot valve shall be of bronze body construction with a sealed spring cage and threaded end connections.. Pilot system shall include all necessary tubing, isolation valves for servicing, opening and closing speed controls, and a strainer for the pilot valve. DIVISION SECTION 15427

13 3. Standard of Quality June 13, Pilot-operated pressure reducing valves shall be Watts Model PV-10, or as approved. A. PRESSURE RELIEF VALVES 0. Acceptable Manufacturers. Watts Regulator Company. 0. Construction Details. Pressure relief valves shall be of the spring-loaded, factory adjusted type with nonmetallic disc and metal seat.. Valves shall be of bronze body construction with threaded end connections.. Valves shall be provided with a test lever and shall be ASME rated for pressure relieving capacity. 0. Standard of Quality. Pressure relief valves shall be Watts No. 174A Series, or as approved. A. COMBINATION PRESSURE AND TEMPERATURE RELIEF VALVES 0. Acceptable Manufacturers. Watts Regulator Company. 0. Construction Details. Combination pressure and temperature relief valves shall be of the spring-loaded, factory adjusted type with nonmetallic disc, metal seat, and a copper or stainless steel expansion type thermostatic element.. Valves shall be of bronze body construction with threaded end connections.. Valves shall be provided with a test lever, and shall be ASME rated for pressure relieving capacity.. Valves shall be AGA certified for temperature relieving capacity. 0. Standard of Quality. Combination pressure and temperature relief valves shall be Watts Series 40, 140, N240, or 340, as applicable, or as approved. DIVISION SECTION 15427

14 June 13, 2003 SECTION PLUMBING TRAPS A. ACCEPTABLE MANUFACTURERS 5. Cast Iron Traps. Jay R. Smith Manufacturing Company.. Josam Manufacturing Company.. Zurn Industries, Inc.. Wade Division, Tyler Pipe.. Or as approved. 5. Chrome-Plated Brass Traps. McGuire Manufacturing Company, Inc.. Kohler Company.. Eljer, an Eljer Industries Company.. Bridgeport Brass Company.. Beaton and Corbin Manufacturing Company.. Or as approved. 5. Polypropylene Anti-Siphon Traps A. CAST IRON TRAPS. Lab-Line/Enfield Industrial Corporation.. R & G Sloane Manufacturing Company, Inc.. Orion Industries, Incorporated.. Or as approved. 5. Traps shall have end connections compatible with the associated piping system. 5. Traps shall be constructed of materials equal to or exceeding the adjoining pipe work. 5. Accessible P-type traps shall be of the deep seal type, shall be provided with an integral cleanout plug, and shall be Jay R. Smith Figure 7222, or as approved. 5. Inaccessible P-type traps shall be of the deep seal type, shall be provided with a top cleanout connection on the discharge, and shall be Jay R. Smith Figure 7230, or as approved. 5. Running traps shall be of the standard seal type, shall be provided with top cleanout connections on both the inlet and the discharge, and shall be Tyler Pipe Figure 7265, or as approved. A. STANDARD FIXTURE TRAPS 5. Traps shall be of the P-type with slip inlet. 5. Traps shall be constructed of brass of not less than 17 gauge thickness and shall be chrome plated. 5. Traps shall include tubing to the wall, a wall escutcheon, and an integral cleanout plug. 5. Traps shall be McGuire Model 8902, or as approved. A. ACID WASTE TRAPS 5. Traps shall be of the anti-siphon type with a seal of not less than 2 inches and shall be provided with a removable sediment bowl of approximately one pint capacity. DIVISION SECTION 15431

15 June 13, Traps shall be of the P-configuration and shall be constructed of polypropylene. 5. Traps shall be Lab-Line Model W511, or as approved. DIVISION SECTION 15431

16 June 13, 2003 SECTION PLUMBING CLEANOUTS B. ACCEPTABLE MANUFACTURERS 0. Cast Iron Units. Jay R. Smith Manufacturing Company.. Josam Manufacturing Company.. Zurn Industries, Inc.. Wade Division, Tyler Pipe.. Or as approved. 0. Bronze Units B. GENERAL. Nibco Incorporated.. ITT Grinnell.. Stanley G. Flagg and Company, Incorporated.. Or as approved. 0. Units shall be complete with all design features and accessories necessary to provide a coordinated installation (such as carpet markers, tile recesses, etc.). B. CLEANOUTS 0. Type 1: (Below Floor Piping - Standard). Adjustable body, cast iron construction with caulk outlet, adjustable housing, ABS internal plug, T-handle, secured scoriated nickel alloy cover plate (carpet markers and tile recesses as required); Jay R. Smith 4031 Series, or as approved. 0. Type 2: (Below Floor Piping Shallow). One piece, nonadjustable, cast nickel alloy body with caulk outlet, threaded scoriated nickel alloy cover with spanner wrench sockets, spanner wrench; Jay R. Smith 4890 Series, or as approved. 0. Type 3: (Above Floor Piping). Straight body, cast iron or cast bronze construction (as applicable) with threaded, raised head, bronze plug; designed to fit in end of standard fitting; Jay R. Smith Figure 4420 for cast iron piping; Nibco No. 816 for DWV piping; or as approved. 0. Type 4: (Base of Riser) B. ACCESS PLATES. Tee body, cast iron or cast bronze construction (as applicable) with bronze, raised head, threaded plug; Jay R. Smith Figure 4512 for cast iron piping; Nibco No. 814 for DWV piping; or as approved. 0. Access plates shall be of stainless steel construction, round, with slightly dished outer edge, and center drilled and countersunk for a flat head screw; Jay R. Smith Figure 4710, or as approved. DIVISION SECTION 15432

17 June 13, 2003 SECTION ROOF DRAINS A. ACCEPTABLE MANUFACTURERS 2. Jay R. Smith Manufacturing Company. 2. Josam Manufacturing Company. 2. Zurn Industries, Inc. 2. Wade Division, Tyler Pipe. 2. Or as approved. A. ROOF DRAINS (Standard) 2. Drains shall be of cast iron construction with secured cast aluminum domes, large sump with 16 inch diameter flange, nonpuncturing clamp ring with integral gravel stop, and bottom outlet compatible with piping system used. 2. Domes shall have a minimum free area of not less than 100 square inches. 2. Every roof drain shall be provided with a deck clamp and a large surface type steel drain receiver. 2. Drains shall be Jay R. Smith Figure 1010-Y, or as approved. A. ROOF DRAINS (IRMA Roofing Systems) 2. Drains shall be of cast iron construction with cast iron extension, primary and secondary nonpuncturing clamp rings, large sump with 16 inch diameter flange, integral gravel stop above top clamp ring, and a bottom outlet compatible with the piping system used. 2. Drains shall be specifically designed for promenade deck use, shall be suitable for use with 2 inch thick concrete pavers, and shall have a flat, 14 inch square, secured grate. Grate shall have a free area of not less than 50 square inches. 2. Drains shall be Jay R. Smith Figure 1409-Y, or as approved. A. ROOF DRAINS (Small Roof Areas) 2. Drains shall be of cast iron construction with secured, cast aluminum domes, small sump with 8-1/2 inch diameter flange, nonpuncturing clamp ring with integral gravel stop, and bottom outlet compatible with piping system used. 2. Domes shall be of the low-profile type with a minimum free area of not less than 40 square inches. 2. Drains shall be Jay R. Smith Figure 1330-Y, or as approved. DIVISION SECTION 15434

18 June 13, 2003 SECTION FLOOR, AREA, AND TRENCH DRAINS B. ACCEPTABLE MANUFACTURERS 9. Jay R. Smith Manufacturing Company. 9. Josam Manufacturing Company. 9. Zurn Industries, Inc. 9. Wade Division, Tyler Pipe. 9. Or as approved. B. GENERAL 9. Drain outlet connections shall be readily adaptable to the piping system in which the drain is used. B. TYPE 1 FLOOR DRAINS (General Purpose - Round) 9. Drains shall be of cast iron construction with two-piece body, double drainage flange, nonpuncturing flashing collar, bottom outlet, and a 6 inch round adjustable nickel alloy strainer. 9. Drains shall be Jay R. Smith Figure 2005-A or 2010-A, as applicable or as approved. B. TYPE 2 FLOOR DRAINS (General Purpose Square) 9. Drains shall be of cast iron construction with two-piece body, double drainage flange, nonpuncturing flashing collar, bottom outlet, and a 6 inch square adjustable nickel alloy strainer. 9. Drains shall be Jay R. Smith Figure 2005-B or 2010-B, as applicable or as approved. B. TYPE 3 FLOOR DRAINS (Kitchen Floor Sink) 9. Drains shall be of cast iron construction with one-piece body, deep square sump, double drainage flange, acid-resistant interior coating, nonpuncturing flashing collar, square nickel alloy top frame, interior domed strainer, bottom outlet, and a 10 inch square nickel alloy loose-set, nontilting grate. 9. Drains shall be Jay R. Smith Figure 3002-NB, or as approved. B. TYPE 4 FLOOR DRAINS (Heavy Traffic Shops) 9. Drains shall be of cast iron construction with two-piece body, double drainage flange, bottom outlet, removable sediment bucket, and a 12 inch round cast iron top with loose-set, nontilting grate. 9. Drains shall be Jay R. Smith Figure 2233 or 2233-Y, as applicable or as approved. B. TYPE 5 FLOOR DRAINS (Mechanical Rooms) 9. Drains shall be of cast iron construction with one-piece body, deep square sump, double drainage flange, nonpuncturing flashing clamp, bottom outlet, removable sediment bucket, square top, and 10 inch square cast iron hinged grate. 9. Drains shall be Jay R. Smith Figure 2415, or as approved. B. AREA DRAINS 9. Drains shall be of cast iron construction with two-piece body, double drainage flange, bottom outlet, and an 8 inch round cast iron loose-set grate. 9. Drains shall be Jay R. Smith Figure 2110, or as approved. DIVISION SECTION 15435

19 X. TRENCH DRAINS June 13, Trench drains shall consist of drain sections and extension sections as required to accommodate the drainage pattern and overall length indicated on the drawings. 9. Drainage sections shall be of cast iron construction with one-piece body, rectangular cross section, flashing clamp, bottom outlet, internal domed strainer, and heavy duty, loose-set, cast iron grate. 9. Extension sections shall be of cast iron construction with one-piece body, rectangular cross section, flashing clamp and heavy duty, loose-set, cast iron grate. 9. Sections shall be designed to bolt together, end to end. End sections shall be bolted to a cast iron end plate with flashing clamp. 9. Trench drains shall be Jay R. Smith Figure 2710-F, or as approved. DIVISION SECTION 15435

20 June 13, 2003 SECTION PLUMBING FIXTURE CARRIERS A. ACCEPTABLE MANUFACTURERS 0. Jay R. Smith Manufacturing Company. 0. Zurn Industries, Incorporated. 0. Josam Manufacturing Company. 0. Wade Division, Tyler Pipe. 0. Or as approved. A. WATER CLOSET CARRIERS 0. Water closet carriers shall be of coated cast iron construction and shall include waste fitting, combination face plate/fixture carrier, fixture coupling, fixture studs, base supports, and all gaskets, washers, bolts, nuts, cap nuts, and accessories necessary for a complete installation. 0. Carriers shall be provided with no-hub type inlet, outlet, and vent connections. 0. Face plates shall be fully adjustable to allow for piping pitch in battery installations while maintaining all fixtures at the same elevation. 0. Fixture coupling and fixture studs shall be adjustable to accommodate varying pipe chase widths. 0. Carriers for handicapped fixtures shall have extra high waste fittings to allow the fixture to be installed in a battery of regular use closets. 0. Base supports shall have provisions for attachment of anchor bolts. 0. All closet carriers shall be provided with an auxiliary supply pipe support. 0. Water closet carriers shall be Jay R. Smith "Linebacker" Series, or as approved. A. URINAL CARRIERS 0. Urinal carriers shall consist of two steel pipe uprights, a top hanger plate, a bottom bearing plate, fixture and bearing studs, and all hardware necessary for a complete installation. 0. Uprights shall include a steel base plate of not less than 4 inches square with mounting holes. 0. Hanger plate and bearing plate heights shall be adjustable to accommodate the fixture being used. 0. All urinal carriers shall be provided with an auxiliary supply pipe support. 0. Urinal carriers shall be Jay R. Smith Figure 637, or as approved. A. LAVATORY CARRIERS 0. Lavatory carriers shall consist of two uprights, an alignment bar, concealed type support arms, and all accessories necessary for a complete installation. 0. Uprights shall be of steel construction with a rectangular cross- section not less than 1 inch wide and not less than 3 inches deep. 0. Uprights shall include a steel base plate of not less than 4 inches square with mounting holes. 0. Concealed support arms shall attach to the uprights through sliding type carriages, adjustable for height. Height adjustment shall be securely lockable. DIVISION SECTION 15438

21 June 13, Support arms shall include a positive latching device for securely fastening the lavatory to the support arm. 0. Lavatory carriers shall be Jay R. Smith Figure 700-M31, or as approved. DIVISION SECTION 15438

22 June 13, 2003 SECTION PLUMBING FIXTURES AND ACCESSORIES C. ACCEPTABLE MANUFACTURERS 1. China and Enameled Cast Iron Fixtures c. Eljer Plumbingware Division, Wallace-Murray Corporation. c. American Standard, Incorporated. (Preferred) c. Crane Company. c. Kohler Company. c. Or as approved. 1. Stainless Steel Fixtures c. Elkay Manufacturing Company. (Preferred) c. Just Manufacturing Company. c. Haws Drinking Fountain Company. c. Or as approved. 1. Toilet Seats c. Bemis Company. c. American Standard, Incorporated (Church). c. Beneke Corporation. c. Sperzel Plumbing Division of Shamrock Neatway Products, Incorporated. c. Or as approved. 1. Flush Valves c. Sloan Valve Company. (Preferred) c. Coyne and Delany Company. c. Or as approved. 1. Lavatory, Sink, and Mop Service Basin Trim c. T & S Brass and Bronze Works, Incorporated. c. Kohler Company. c. American Standard, Incorporated. c. The Chicago Faucet Company. c. Eljer Plumbingware Division, Wallace-Murray Corporation. c. Speakman Company. c. Or as approved. 1. Electric Water Coolers and Drinking Fountains c. Elkay Manufacturing Company. (Preferred) c. Halsey Taylor Division, King-Seeley Thermos Corporation. c. Haws Drinking Faucet Company. c. Sunroc-Western Corporation. c. Oasis, EBCO Manufacturing Company. c. Or as approved. 1. Shower Units and Wash Fountains c. Bradley Corporation. c. Acorn Engineering Company. c. Symmons Regulator Company. c. Or as approved. DIVISION SECTION 15440

23 8. Shower Pressure Balancing Valves June 13, 2003 a. Symmons Industries, Incorporated. b. Powers Regulator Company. c. Speakman Company. d. The Chicago Faucet Company. e. Or as approved. 9. Mop Service Basins and Shower Bases a. Florestone Products Company. b. Fiat Products, Incorporated. c. Stern-Williams Company, Incorporated. d. E. L. Trustee & Sons, Incorporated. e. Or as approved. 10. Emergency Fixtures Q. QUALITY ASSURANCE a. Haws Drinking Faucet Company. b. Speakman Company. c. Or as approved. 1. Units shall meet or exceed requirements of all applicable environmental conservation and energy conservation codes and regulations. R. GENERAL 1. Plumbing fixtures shall be complete with all necessary connections, equipment, trim, fittings, and supports. 2. Unless specifically noted otherwise, each fixture shall be provided complete with appropriate carrier. 3. All fixtures and trim shall be constructed of materials free from defects in a manner of first class workmanship. 4. All units shall be suitable for service corresponding to the working pressure as specified for the adjoining piping. 5. Vitreous china units shall be of "first-quality" vitreous china, thoroughly fused and vitrified to a homogeneous mass. 6. Stainless steel units shall be of one-piece, high grade, heavy gauge stainless steel and welded seamless construction. 7. Enameled cast iron units shall be of one-piece high grade cast iron with a thoroughly fused enamel surface. 8. Unit surfaces intended for contact with walls, floors or other fixtures shall be of the proper plane as required to set the unit level and plumb. 9. It shall be the Contractor's responsibility to guarantee proper selection and coordination of all fittings and parts relating to each fixture. 10. All fixtures shall be provided with individual stop valves on all water supply services. 11. Unless otherwise specified, all exposed piping adjacent to fixtures (including valves, fittings, trim, etc.) shall be chromium plated red brass. 12. The "PF-" numbers indicated in the following paragraphs correspond to the designations to be indicated on the drawings. DIVISION SECTION 15440

24 S. PF-1A, WATER CLOSET (Wall-Mounted) June 13, Fixture shall be wall-mounted, siphon jet action, elongated bowl, 14 inches wide by 24-3/4 inches long, vitreous china, white, 1-1/2 inch brass top spud, 2-1/4 inch pass ball, suitable for 1.5 gallon/cycle flush valve. c. Eljer "Signature" No , or as approved. 1. Trim shall include an exposed chrome plated closet flush valve with 1.5 gallon/cycle option, metal oscillating nonhold-open handle, 1 inch I.P.S. screwdriver back-check angle stop with protective cap, adjustable tailpiece, vacuum breaker, flush connection and spud coupling for 1-1/2 inch top spud, and wall and spud flanges, 24 inch rough-in dimension. c. Sloan Royal Flush No , or as approved. 1. Seat shall be white solid plastic, elongated, open front, with stainless steel, self-sustaining check hinge. c. Beneke No. 563-SS, or as approved. 1. Carrier shall be as specified in Section 15438, PLUMBING FIXTURE CARRIERS. C. PF-1B, WATER CLOSET (Floor-Mounted, for replacement of existing only) 1. Fixture shall be floor mounted, siphon jet action, elongated bowl, 14 inches high by 14-1/2 inches wide by 25-1/4 inches long, white vitreous china, 1-1/2 inch brass top spud, pass ball 2-1/4 inch, suitable for 1.5 gallon/cycle flush valve, 12 inch rough, bolt caps, and connection seal. c. Eljer "Preserver" No , or as approved. 1. Trim and seat shall be as specified for PF-1A. C. PF-1C, WATER CLOSET (Floor-Mounted Handicapped, for replacement of existing only.) 1. Fixture shall be floor-mounted, tank type siphon jet action, elongated bowl, 16-3/4 inches high, by 20-1/2 inches wide by 29 inches long, white vitreous china, 2-1/4 inch (minimum) ball pass, suitable for 1.5 gallon/cycle flush, 12 inch rough, complete with bolt caps and connection seal. c. Eljer "Patriot" No , or as approved. 1. Supply shall be a chrome plated angle supply with 3/8 inch o.d. x 12 inch flex riser, wheel handle, and escutcheon. c. Eljer No , or as approved. 1. Seat shall be white solid plastic, elongated, open front, stainless steel, and self-sustaining check hinge. C. PF-2, URINAL c. Eljer No , or as approved. 1. Fixture shall be wall-mounted, siphon jet action, 3/4 inch inlet spud, flushing rim, 16 inches wide, 14 inches long, vitreous china, white, outlet connection threaded 2 inch IPS, suitable for 1 gallon/cycle flush valve. c. American Standard # , or as approved. 1. Trim shall consist of an exposed urinal flush valve with 1 gallon/ cycle option, metal oscillating nonhold-open handle, screw driver back-check stop with protective cap, adjustable tailpiece, vacuum breaker flush connection, and spud coupling for 3/4 inch top spud, wall, and spud flanges. c. Sloan No AF, or as approved. DIVISION SECTION 15440

25 June 13, Carrier shall be as specified in Section 15438, PLUMBING FIXTURE CARRIERS. C. PF-3A, LAVATORY (Wall Mounted) 1. Fixture shall be wall-mounted, soap depression, faucet holes at 8 inch centers, vitreous china, white, concealed front overflow, 20 by 18, ledge back, with drilling for carrier. c. American Standard # or , or as approved. 1. Trim shall consist of a self-closing, mixing type, faucet with cast brass construction, chrome plated, 4 inch spout with 1.0 gpm vandalproof aerator, rigid copper connectors for adjustable faucet centers, pushbutton valves with individual escutcheons, pop-up drain with 1-1/4 inch tailpiece. c. T&S No. B-2824 with B F-10 outlet, or as approved. 1. Supply shall consist of 3/8 inch pipe with nipple to wall, escutcheon plate, annealed vertical tube, loose key stops. c. McGuire No. 165LK, or as approved. 1. Trap, 1-1/4 inches by 1-1/2 inches, shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. 1. Carrier shall be as specified in Section 15438, PLUMBING FIXTURE CARRIERS. 1. Handicapped Units c. Insulate all exposed supply and drain piping including trap and angle stops. Provide protective jacketing as specified in Section 15260, PIPING INSULATION. or a. Provide each unit with a protective, tamper-resistant molded rigid vinyl that fully encloses the hot water, cold water, and drain piping. The device shall protect a lavatory user from burns. The device shall protect components from tampering, and comply with ADA article Shields shall be Truebro Rigiwall-E or as approved. I. PF-3B, LAVATORY, COUNTER TOP ( Handicapped) 0. PF-3B: Countertop Handicapped. Fixture shall be a counter top, self-rimming, oval lavatory, 20 inches by 17 inches in size, soap depression, faucet holes at 8 inch centers, white vitreous china, concealed front overflow.. Eljer "Laura" No , or as approved. 0. PF-3C: Countertop Standard. Fixture shall be under counter top, rimless, oval lavatory, 19 inches by 15 inches in size, faucet holes at 4 inch centers, white vitreous china, and concealed front overflow.. Eljer "Barrow" No , or as approved. 0. Trim and accessories shall be as specified for PF-3A. 0. Trim and accessories shall be as specified for PF-3A. DIVISION SECTION 15440

26 Q. PF-4, MOP SERVICE BASIN June 13, Fixture shall be floor supported, 36 inches by 24 inches by 10 inches deep, manmade molded stone, white, integral 3 inch stainless steel strainer and tailpiece, aluminum threshold guard.. Fiat Products, Incorporated, No. MSB-3624, or as approved. 0. Trim shall consist of a faucet, chrome plated, with vacuum breaker, integral stops, wall brace, threaded spout, pail hook, loose keystops in shanks, 8 inch on centers, 10 inches from wall to center of spout outlet, flow cartridge set for 3 gpm.. Eljer No , or as approved. 0. Trap (3 inches by 3 inches) shall be of the cast iron P-type as specified in Section 15431, PLUMBING TRAPS, for fixtures. 0. Accessories shall consist of a hose and hose bracket. I. PF-5A, WALL SHOWER (1 to 3 STATIONS) 0. Fixture shall consist of a single or multi-head shower unit plus a shower base. 0. Shower unit shall be of the wall-mounted, panel type, stainless steel construction, two adjustable spray pattern heads mounted 6 feet above the floor, 2.5 gpm volume control, two separate pressure balancing mixing valves, integral stops in the supplies, recessed soap dish at each station.. Bradley Model 1,W 2W, 3W or as approved. I. PF-5B, WALL SHOWER ( 4 OR MORE STATIONS) 0. Fixture shall be wall-mounted, multiple panel with end caps, filler pieces, access panels, fasteners and mounting devices, stainless steel shower with concealed piping, all exposed parts are stainless steel or chrome plated brass, pressure balancing mixing valves, supply piping and fitting are wrought copper or cast brass, water-saver shower head, and vandal resistant.. Wall mounted, multiple panel stainless shower, 14 inches high, 4 inches deep, length as indicated on drawings.. All exposed parts are stainless steel or chrome plated brass, concealed piping and fittings are wrought copper or cast brass.. Shower panels, end caps, filler pieces, and access panels are 18 gauge, Type 304, stainless steel polished to a No. 4 satin finish.. Mixing Valves: Pressure balancing, all brass construction, chrome plated, manufactured by Symmons.. Shower Heads: Severe service type, vandal resistant, fixed direction head, spray adjustment through orifice with allen key, chrome plated brass, secured to shower panel, water-saver 2.5 gpm flow control, and stops in supplies. Head spacing as indicated on drawings.. Shower unit shall be Bradley Model Panelon, or as approved. 0. Support fixture as recommended by manufacturer. DIVISION SECTION 15440

27 T. PF-5C, WALL SHOWER (HANDICAPPED) June 13, Fixture shall be wall-mounted, control panel, stainless steel with concealed piping, all exposed parts are stainless steel or chrome plated brass, pressure balancing mixing valve, diverter valve, piping and fittings are wrought copper or cast brass, water-saver shower head, vandal resistant, hand held shower head with flexible hose and inline backflow preventer.. Wall mounted, control panel, stainless shower, 32 inches wide by 48 inches high by 4 inches deep.. All exposed parts are stainless steel or chrome plated brass, concealed piping and fittings are wrought copper or cast brass.. Shower panel, top and bottom covers, mounting frame are 18 gauge, type 304. Stainless steel polished to a No. 4 satin finish.. Mixing Valve: Pressure balancing type, all brass construction, chrome plated, manufactured by Symmons.. Diverter Valve: Lever handle, all brass construction, chrome plated, manufactured by Symmons.. Shower Head: Severe service type, vandal resistant, fixed direction head, spray adjustment through orifice with allen key, chrome plated brass, secured to a stainless steel wall flange, bolted with stainless steel screws to back plate, water-saver 2.5 gpm flow control, and stops in supplies.. Hand held shower head with swivel connector, 59 inch stainless steel extra heavy-duty flexible hose, elevated backflow preventer (chrome plated), post type mounting bracket for holding shower head also chrome plated.. Shower unit shall be Bradley HN-600, or as approved. 0. Support fixture as recommended by manufacturer. I. PF-5D, COLUMN SHOWER (MULTI-STATION) 0. Fixture shall consist of a multi-head shower unit. 0. Shower unit shall be of the column type with shroud assembly to finished ceiling and circular soap tray, stainless steel construction, adjustable spray pattern heads mounted 6 feet above the floor, 2.5 gpm flow control, six separate pressure balancing mixing valves, supplies from below with integral stops, dome type grate drain, and vent off drain.. Bradley Model 5CA or 6CB, 6 foot 0 inch, EF-ST-2.5FC-DG, or as approved. I. PF-6A, ELECTRIC WATER COOLER (SURFACE WALL-MOUNTED) 0. The fixture shall consist of an exposed, wheelchair height, wall mounted, refrigerated water cooler. The handicapped fountain shall have a 19 inch projection and shall have self-closing pressbar, operable from either front or sides. Safety bubbler shall flex on impact to prevent accidental injury. Unit shall meet UL requirements and all sanitary codes. Unit shall meet all applicable sections of ANSI Standard A Fountain Top: One-piece, 18 gauge stainless steel, Type 302, anti-splash basin with embossed stream splitter, drain grid, and bubbler mount, undercoated nonexposed area.. Stream Projectors: Pushbar operated, self-closing valve controls with in-line flow regulators from 20 to 100 psi and stream projectors with protective hoods.. Colors: Cabinet shall be gray beige vinyl with color coordinated pressbar. Submit standard manufacturer's color selection chart for final verification of color selected. DIVISION SECTION 15440

28 June 13, 2003 c. Mounting Chassis: Cabinet design shall allow for flush-to-wall mounting. Galvanized chassis shall support fountain top and all workings. c. Cooling System: Hermetically sealed, reciprocating type motor compressor, rating 1/5HP, 115V, 1PH, 60HZ, 4.5 amps, combination tube-tank type, self-cleansing, all copper insulated cooling unit, refrigerant type 12, controlled by capillary tube, enclosed adjustable thermostat, five year warranty. Capacity of cooler shall be 8 gallons per hour delivered at 50 degrees F with an ambient temperature on the condenser coil of 80 degrees F. Ratings shall be in accordance with ARI Standard Unit shall be Underwriters Laboratories Inc. listed. c. Unit shall be Elkay No. EBFS-8-G Wheelchair Access Model, or as approved. 3. Supply to the refrigeration unit shall consist of 3/8 inch pipe with loose key stop, reducer as required. c. McGuire, or as approved. 2. Traps (1-1/4 inch by 1-1/2 inch) shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. Q. PF-6B, ELECTRIC WATER COOLER (SEMI-RECESSED, BI-LEVEL) 1. Fixture shall be fully exposed wall type with recessed-in-the-wall refrigeration unit, 14 inch diameter contoured basin drinking fountain, 19 inch projection with support arm, wall plate/front panel grille, stream projector, pushbar control on front, all stainless steel with bronzetone finish. c. Fountain: 18 gauge stainless steel, Type 302, polished satin finish, 14 inch contoured basin with support arm (which incorporates a recess to be integrated with basin) front panel bar control, an in-line flow regulator from 20 to 100 psi and stream project with bronzetone finish. c. Wall Plate/Front Panel Grille: 18 gauge stainless steel, Type 302, polished satin finish to match fountain. c. Wall Mounting Box: 18 gauge steel designed for fully recessed mounting of unit and provided with prepunched plumbing and electrical service holes. c. Cooling System: Hermetically sealed reciprocating-type motor compressor, rating 1/5 HP, 115V, 1 PH, 60 HZ, 4.7 amps, combination tube-tank type, self-cleansing, all copper insulated cooling adjustable thermostat, five-year warranty. Capacity of cooler shall be 8 gallons per hour delivered at 50 degrees F with an ambient temperature on the condenser coil of 80 degrees F. Ratings shall be in accordance with ARI Standard Unit shall be Underwriters Laboratories Inc. listed. c. Unit shall be Elkay Model No. ERP2-8C, or as approved. c. Supply shall be as specified for PF-6A. c. Traps (1-1/4 inches by 1-1/2 inches) shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. P. PF-6C, ELECTRIC WATER COOLER (FULLY-RECESSED) 0. Fixture shall be fully-recessed, wall-mounted, 19 inches wide by 54-1/4 inches high by 11-3/4 inches recess, stainless steel fountain and grille, electric refrigerated water cooler, plumbing and electrical connections are concealed, pushbutton control located on front panel below stream projector.. Fountain Top: One-piece, 18 gauge stainless steel, Type 302, undercoated, stream projector with pushbutton control operator, mounted on front of fountain below projector.. Front Panel Grille: Made of Type 302, stainless steel, polished luster finish, and removable louvered ventilating grille encloses refrigeration unit and plumbing. DIVISION SECTION 15440

29 June 13, Wall Mounting Box: Allows flush mounting to finished wall, plumbing and electrical service holes are prepunched on both right and left side to facilitate installation.. Cooling System: Hermetically sealed reciprocating type motor compressor, rating 1/5 HP, 115V, 1 PH, 60 HZ, 4.5 amps. Combination tube-tank type, self-cleansing, all copper, insulated cooling unit, refrigerant Type 12 is controlled by accurately calibrated capillary tube, enclosed adjustable thermostat, five-year warranty, capacity of cooler shall be 7.8 gallons per hour delivered at 50 degrees F with an ambient temperature on the condenser coil of 90 degrees F. Ratings shall be in accordance with ARI Standard Unit shall be Underwriters Laboratories, Inc. listed.. Unit shall be Elkay Model No. EFRC-8, or as approved. 0. Supply shall consist of 3/8 inch pipe with wheel handle stop, chrome-plated.. McGuire, or as approved. 0. Trap (1-1/4 inches by 1-1/2 inches) shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. P. PF-7A, WASHFOUNTAINS (MULTI-STATION WALL TYPE) 0. Fixture shall be a wall type, foot controlled,, semi-circular wash fountain with stainless steel bowl, stainless steel skirt, stainless steel scuff guard base, stainless steel spray head, and stainless steel spray head support. 0. Unit shall include a liquid soap dispenser, a mechanical mixing valve, a volume control valve, a slowclosing foot valve, combination stop-strainer check valves on the inlets, and a beehive strainer. 0. Unit shall be Bradley CFC Series, or as approved. P. PF-7B, WASHFOUNTAIN (MULTI-STATION FLOOR TYPE) 0. Fixture shall be a floor type, pushbutton controlled, semi-circular washfountain with stainless steel bowl, stainless steel skirt, stainless steel spray head, and stainless steel spray head support. 0. Unit shall include a liquid soap dispenser, a mechanical mixing valve, a volume control valve, a slowclosing metering type pushbutton, combination stop-strainer-check valves on the inlets, and a beehive strainer. 0. Unit shall be Bradley 2136-A, or as approved. P. PF-8, SINK (COUNTER TOP) 0. PF-8A: Single Compartment - Standard:. Sink shall be a single basin 22 inches by 19 inches by 7-1/2 inches deep, 18 gauge, Type 304 (18-8), stainless steel, self-rimming, faucet deck, back and side ledges, three 1-1/2 inch hole drillings, 3-1/2 inch drain opening, undercoated.. Elkay No. LR-2219, or as approved. 0. PF-8B: Single Compartment - Handicapped:. Sink shall be a single shallow basin, 25 inches by 21 inches by 5-1/2 inches deep, 20 gauge, Type 302, stainless steel, self-rimming, faucet deck, back and side ledges, three 1-1/2 inch hole drillings, offset 3-1/2 inch drain opening, undercoated.. Handicapped sink shall be Elkay No. LRAD , or as approved. 0. PF-8C: Two-Compartment - Standard: DIVISION SECTION 15440

30 June 13, Sink shall be a double basin, 33 inches by 21 inches by 8 inches deep, 18 gauge, Type 304 (18-8), stainless steel, self-rimming, faucet deck, back and side ledges, three 1-1/2 inch hole drillings, two 3-1/2 inch drain openings, undercoated.. The two drain tailpieces shall be connected with a continuous waste fitting, 1-1/2 inch by 1-1/2 inch by 1-1/2 inch size, chrome plated. Elkay No. LK-53, or as approved.. Two-compartment sink shall be Elkay No. LR-3321, or as approved. 0. PF-8D: Two-Compartment Handicapped:. Sink shall be a double shallow basin, 33 inches by 21 inches by 5 1/2 inches deep, 20 gauge, Type 302, stainless steel, self-rimming, faucet deck, back and side ledges, three 1-1/2 inch hole drillings, backset 3-1/2 inch drain opening in each basin, undercoated.. The two drain tailpieces shall be connected with a continuous waste fitting, 1-1/2 inch by 1-1/2 inch by 1-1/2 inch size, chrome plated. Elkay No. LK-53, or as approved.. Two-compartment handicapped sink shall be Elkay No. LRAD 3321, or as approved. 0. Trim shall consist of a faucet with compression valves, cast brass construction, chrome plated, 8 inch centers, standard handles, 8 inch swing spout, individual escutcheons, aerator.. Elkay No. LK-230, or as approved. 0. Supplies shall consist of 1/2 inch pipe with nipple to wall, escutcheon plate, annealed vertical tube, angle stops, reducers as necessary.. McGuire No. H-165, or as approved. 0. Drain shall include drain body, removable crumb cup and stop, and 1-1/2 inch tailpiece.. McGuire No. 151, or as approved. 0. Trap (1-1/2 inches by 1-1/2 inches) shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. P. PF-9, EMERGENCY EYE-WASH 0. Fixture shall be wall mounted, stainless steel receptor, push type stay open ball valve, plastic antisurge spray head, spray head covers, and integral pressure compensating controller. 0. Trap (1-1/4 inches by 1-1/2 inches) shall be as specified in Section 15431, PLUMBING TRAPS for fixtures. 0. Spray head covers shall be plastic construction, with metal ball chains, designed specifically to cover spray heads. 0. Provide each fixture with an identification sign. Signs shall be plastic construction, pictorial type, minimum 8 inches high by 11 inches wide. Signs shall bear the label "EMERGENCY EYE WASH." 0. Unit shall be Haws Drinking Faucet Company, Model 7460BT, or as approved. DIVISION SECTION 15440

31 U. PF-9B, EMERGENCY SHOWER/EYE WASH STATION June 13, Fixture shall be a complete safety station with an emergency shower and emergency eye wash fountain wall mounted in compliance with ANSI Z Shower shall be of the deluge type with a stainless steel shower head. Shower shall be controlled by a pull-to-open, self-closing ball valve activated by a stainless steel triangular pull handle.. Eye wash fountain shall be wall mounted stainless steel with brass spray heads (shielded) by safety yellow polypropylene shrouds. Eye wash shall be controlled by a stay-open ball valve activated by stainless steel push handle.. Fixture shall be provided with 1 inch supply and 1 1/4 inch waste connection tappings.. Fixture shall be Speakman Model SE-227-SS with PE-296 eye saver eye wash, or as approved. 0. Supply shall consist of 1 1/2 inch pipe with isolation valve and reducer adaptor. 0. Trap shall be of a P-type, adjustable, swivel ell, cast brass, cleanout plug, slip inlet 1 1/4 inches by 1 1/2 inches. P. PF-10, UTILITY SINK. Kohler No. K-9000, or as approved. 0. Sink shall be single basin, 23 inches by 23-3/8 inches by 14 inches deep, fiberglass with steel legs for floor mounting, molded self-draining soap dishes, and drain assembly kit.. Swan Co. Model No. MF-1F, or as approved. 0. Trim shall consist of a faucet with compression valves, cast brass construction, chrome plated, 4 inch centers, standard handles, 8 inch swing spout and faucet block.. Eljer No , or as approved. 0. Supplies shall consist of ½ inch pipe with nipple to wall, escutcheon, annealed tube, angle stops, reducers as necessary.. McGuire No. H2158LK, or as approved. 0. Trap (1-1/2 inches by 1-1/2 inches) shall be as specified in Section 15431, PLUMBING TRAPS, for fixtures. DIVISION SECTION 15440