TEST REPORT IEC Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires

Transcription

1 age 1 of 54 TEST REORT IEC Luminaires art 2: articular requirements Section 1: Fixed general purpose luminaires Report Number.... : Date of issue... : Total number of pages pages Name of Testing Laboratory preparing the Report... : Applicant s name... : Address... : TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch hilips Lighting Luminaires (Shanghai) Co., Ltd 2F, Building 6, No. 1805, Huyi Highway, Malu Town, Jiading District, , Shanghai, eople's Republic of China Test specification: Standard... : Test procedure... : Non-standard test method... : IEC :1979 (First Edition) + A1:1987 used in conjunction with IEC :2014 (Eighth Edition) EU-Directive Test Report Form No.... : Test Report Form(s) Originator... : Master TRF... : IEC60598_2_1D Intertek Semko AB Copyright 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report.

2

3 age 3 of 54 Report No.: Tested by (name, function, signature)...: Witnessed by (name, function, signature).: Approved by (name, function, signature)...: Supervised by (name, function, signature) :

4 age 4 of 54 Report No.: List of Attachments (including a total number of pages in each attachment): attachment 1 for the additional requirements of EN attachment 2 for the additional requirements of EN Summary of testing: Determination of the test result includes consideration of measurement uncertainty from the test equipment and methods. All applicable hazards are covered by the harmonized standard. Tests performed (name of test and test clause): Complete tests are performed on BCW098 LED20/NW SU L600, BCW098 LED40/NW SU L1200 and BCW098 LED40/CW SD L1200 Testing location: TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch No. 1999, Duhui Road, Shanghai, ,. R. China Construction check on other models Requirement of EN have been evaluated and found to be met by testing. The test results comply with the requirements Summary of compliance with National Differences: List of countries addressed The deviation between EN :1989 used in conjunction with EN :2015 and IEC :1979 (First Edition) + A1:1987 used in conjunction with IEC :2014 (Eighth Edition) is taken into account at the end of the report, please refer to appendix 1 of this report. The product fulfils the requirements of EN :1989

5 age 5 of 54 Report No.: Copy of marking plate: Note 1: Height of letter and numeral not less than 2mm, graphical symbol not less than 5mm, WEEE not less than 7mm. Note 2: The labels of other types are similar with the above, just the different model name and specification. The above label are drafts of an artwork for marking plate pending approval by National Certification Bodies and it shall not be affixed to products prior to such an approval.

6 age 6 of 54 Report No.: Test item particulars...: Fixed general purpose luminaires (LED Waterproof) Classification of installation and use...: Class I Supply Connection...: Terminal...: ossible test case verdicts: - test case does not apply to the test object...: - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F (Fail) Testing...: Date of receipt of test item...: Date (s) of performance of tests...: to General remarks: "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Remark: The following contents are included and as appendix of this test report: 1) Test report IEC :1979 (First Edition) + A1:1987 used in conjunction with IEC :2014 (Eighth Edition) 2) Appendix 1: comprising: Deviation of EN :1989 used in conjunction with EN :2015 to IEC :1979 (First Edition) + A1:1987 used in conjunction with IEC :2014 (Eighth Edition). 3) Appendix 2: comprising: Additional requirements of EN 62031: 2008+A1: 2013+A2: ) Appendix 3: hotograph Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : NingBo Violet Lighting Electric Co.,Ltd No.885 Jinhai Rd,Cidong Industrial ark,cixi, , Zhejiang, eople's Republic of China

7 age 7 of 54 Report No.: General product information: The products covered in this test report are LED fixed luminaires. Model ower Lamp LED driver LxWxH (CM) BCW098 LED20/NW SU L600 19W 19W/44x0,4W Xitanium 36W ,7x10x8,4 LED 0.4A 115V 230V BCW098 LED20/CW SU L600 19W 19W/44x0,4W Xitanium 36W ,7x10x8,4 LED 0.4A 115V 230V BCW098 LED40/NW SU 38W 38W/88x0,4W Xitanium 75W ,9X10X8,4 L1200 LED 0.4A 220V 230V BCW098 LED40/CW SU 38W 38W/88x0,4W Xitanium 75W ,9X10X8,4 L1200 LED 0.4A 220V 230V BCW098 LED40/NW SD 38W 38W/88x0,4W Xitanium 75W ,9X10X8,4 L1200 LED 0.40A 215V TD 230V BCW098 LED40/CW SD L W 38W/88x0,4W LED Xitanium 75W A 215V TD 230V 118,9X10X8,4

8 age 8 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.2 (0) GENERAL TEST REQUIREMENTS 1.2 (0.1) Information for luminaire design considered... : Standard EN Yes No 1.2 (0.3) More sections applicable... : Yes No 1.4 (2) CLASSIFICATION 1.4 (2.2) Type of protection... : Class I 1.4 (2.3) Degree of protection... : I (2.4) Luminaire suitable for direct mounting on normally flammable surfaces... : Yes No 1.4 (2.5) Luminaire for normal use... : Yes No Luminaire for rough service... : Yes No 1.5 (3) MARKING 1.5 (3.2) Mandatory markings osition of the marking Format of symbols/text 1.5 (3.3) Additional information Language of instructions English 1.5 (3.3.1) Combination luminaires 1.5 (3.3.2) Nominal frequency in Hz 50/60Hz 1.5 (3.3.3) Operating temperature 1.5 (3.3.4) Symbol or warning notice 1.5 (3.3.5) Wiring diagram 1.5 (3.3.6) Special conditions 1.5 (3.3.7) Metal halide lamp luminaire warning 1.5 (3.3.8) Limitation for semi-luminaires 1.5 (3.3.9) ower factor and supply current 1.5 (3.3.10) Suitability for use indoors 1.5 (3.3.11) Luminaires with remote control 1.5 (3.3.12) Clip-mounted luminaire warning 1.5 (3.3.13) Specifications of protective shields 1.5 (3.3.14) Symbol for nature of supply ~ 1.5 (3.3.15) Rated current of socket outlet

9 age 9 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.5 (3.3.16) Rough service luminaire 1.5 (3.3.17) Mounting instruction for type Y, type Z and some type X attachments 1.5 (3.3.18) Non-ordinary luminaires with VC cable 1.5 (3.3.19) rotective conductor current in instruction if applicable 1.5 (3.3.20) rovided with information if not intended to be mounted within arm s reach 1.5 (3.3.21) Non-replaceable and non-user replaceable light sources information provided Cautionary symbol 1.5 (3.3.22) Controllable luminaires, classification of insulation provided 1.5 (3.4) Test with water Test with hexane Legible after test Label attached 1.6 (4) CONSTRUCTION 1.6 (4.2) Components replaceable without difficulty 1.6 (4.3) Wireways smooth and free from sharp edges 1.6 (4.4) Lampholders 1.6 (4.4.1) Integral lampholder 1.6 (4.4.2) Wiring connection 1.6 (4.4.3) Lampholder for end-to-end mounting 1.6 (4.4.4) ositioning - pressure test (N)... : After test the lampholder comply with relevant standard sheets and show no damage After test on single-capped lampholder the lampholder have not moved from its position and show no permanent deformation - bending test (N)... : After test the lampholder have not moved from its position and show no permanent deformation 1.6 (4.4.5) eak pulse voltage 1.6 (4.4.6) Centre contact

10 age 10 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.6 (4.4.7) arts in rough service luminaires resistant to tracking 1.6 (4.4.8) Lamp connectors 1.6 (4.4.9) Caps and bases correctly used 1.6 (4.4.10) Light source for lampholder or connection according IEC not connected another way 1.6 (4.5) Starter holders Starter holder in luminaires other than class II Starter holder class II construction 1.6 (4.6) Terminal blocks Tails Unsecured blocks 1.6 (4.7) Terminals and supply connections 1.6 (4.7.1) Contact to metal parts 1.6 (4.7.2) Test 8 mm live conductor Test 8 mm earth conductor 1.6 (4.7.3) Terminals for supply conductors 1.6 ( ) Welded method and material - stranded or solid conductor - spot welding - welding between wires - Type Z attachment - mechanical test according to electrical test according to heat test according to and (4.7.4) Terminals other than supply connection 1.6 (4.7.5) Heat-resistant wiring/sleeves 1.6 (4.7.6) Multi-pole plug - test at 30 N 1.6 (4.8) Switches - adequate rating - adequate fixing - polarized supply - compliance with IEC for electronic switches 1.6 (4.9) Insulating lining and sleeves

11 age 11 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.6 (4.9.1) Retainment Method of fixing... : Heat shrinkable 1.6 (4.9.2) Insulated linings and sleeves: Resistant to a temperature > 20 C to the wire temperature or a) & c) Insulation resistance and electric strength b) Ageing test. Temperature (C)... : 1.6 (4.10) Double or reinforced insulation 1.6 (4.10.1) No contact, mounting surface accessible metal parts wiring of basic insulation Safe installation fixed luminaires Capacitors and switches Interference suppression capacitors according to IEC (4.10.2) Assembly gaps: - not coincidental - no straight access with test probe 1.6 (4.10.3) Retainment of insulation: - fixed - unable to be replaced; luminaire inoperative - sleeves retained in position - lining in lampholder 1.6 (4.11) Electrical connections and current-carrying parts 1.6 (4.11.1) Contact pressure 1.6 (4.11.2) Screws: - self-tapping screws - thread-cutting screws 1.6 (4.11.3) Screw locking: - spring washer - rivets 1.6 (4.11.4) Material of current-carrying parts 1.6 (4.11.5) No contact to wood or mounting surface 1.6 (4.11.6) Electro-mechanical contact systems 1.6 (4.12) Screws and connections (mechanical) and glands 1.6 (4.12.1) Screws not made of soft metal

12 age 12 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Screws of insulating material Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : 1.6 (4.12.2) Screws with diameter < 3 mm screwed into metal 1.6 (4.12.4) Locked connections: - fixed arms; torque (Nm)... : - lampholder; torque (Nm)... : - push-button switches; torque 0,8 Nm... : 1.6 (4.12.5) Screwed glands; force (Nm)... : 1.6 (4.13) Mechanical strength 1.6 (4.13.1) Impact tests: - fragile parts; energy (Nm)... : - other parts; energy (Nm)... : 0,35Nm 1) live parts 2) linings 3) protection 4) covers 1.6 (4.13.3) Straight test finger 1.6 (4.13.4) Rough service luminaires - I54 or higher a) fixed b) hand-held c) delivered with a stand d) for temporary installations and suitable for mounting on a stand 1.6 (4.13.6) Tumbling barrel 1.6 (4.14) Suspensions, fixings and means of adjusting 1.6 (4.14.1) Mechanical load: A) four times the weight B) torque 2,5 Nm C) bracket arm; bending moment (Nm)... : D) load track-mounted luminaires E) clip-mounted luminaires, glass-shelve. Thickness (mm)... :

13 age 13 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Metal rod. diameter (mm)... : Fixed luminaire or independent control gear without fixing devices 1.6 (4.14.2) Load to flexible cables Mass (kg)... : Stress in conductors (N/mm²)... : Mass (kg) of semi-luminaire... : Bending moment (Nm) of semi-luminaire... : 1.6 (4.14.3) Adjusting devices: - flexing test; number of cycles... : - strands broken... : - electric strength test afterwards 1.6 (4.14.4) Telescopic tubes: cords not fixed to tube; no strain on conductors 1.6 (4.14.5) Guide pulleys 1.6 (4.14.6) Strain on socket-outlets 1.6 (4.15) Flammable materials - glow-wire test 650C... : See Test Table 1.15 (13.3.2) - spacing 30 mm - screen withstanding test of screen dimensions - no fiercely burning material - thermal protection - electronic circuits exempted 1.6 (4.15.2) Luminaires made of thermoplastic material with lamp control gear a) construction b) temperature sensing control c) surface temperature 1.6 (4.16) Luminaires for mounting on normally flammable surfaces No lamp control gear... : (compliance with Section 12) 1.6 (4.16.1) Lamp control gear spacing: - spacing 35 mm - spacing 10 mm 1.6 (4.16.2) Thermal protection: - in lamp control gear

14 age 14 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - external - fixed position - temperature marked lamp control gear 1.6 (4.16.3) Design to satisfy the test of 12.6 (see clause 12.6) 1.6 (4.17) Drain holes Clearance at least 5 mm 1.6 (4.18) Resistance to corrosion 1.6 (4.18.1) - rust-resistance 1.6 (4.18.2) - season cracking in copper 1.6 (4.18.3) - corrosion of aluminium 1.6 (4.19) Igniters compatible with ballast 1.6 (4.20) Rough service vibration 1.6 (4.21) rotective shield 1.6 (4.21.1) Shield fitted if tungsten halogen lamps or metal halide lamps Shield of glass if tungsten halogen lamps 1.6 (4.21.2) articles from a shattering lamp not impair safety 1.6 (4.21.3) No direct path 1.6 (4.21.4) Impact test on shield Glow-wire test on lamp compartment... : See Test Table 1.15 (13.3.2) 1.6 (4.22) Attachments to lamps not cause overheating or damage 1.6 (4.23) Semi-luminaires comply Class II 1.6 (4.24) hotobiological hazards 1.6 (4.24.1) No excessive UV radiation if tungsten halogen lamps and metal halide lamps (Annex ) 1.6 (4.24.2) Retinal blue light hazard Luminaires with E thr : a) Fixed luminaires - distance x m, borderline between RG1 and RG2.. : RG0 - marking and instruction according b) ortable and handheld luminaires - marking according if RG1 exceeded at 200 mm according to IEC/TR 62778

15 age 15 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict ortable luminaires for children IEC and Mains socket outlet nightlights IEC not exceed RG1 at 200 mm according to IEC/ (4.25) Mechanical hazard No sharp point or edges 1.6 (4.26) Short-circuit protection 1.6 (4.26.1) Adequate means of uninsulated accessible SELV parts 1.6 (4.26.2) Short-circuit test with test chain according Test chain not melt through Test sample not exceed values of Table 12.1 and (4.27) Terminal blocks with integrated screwless earthing contacts Test according Annex V ull test of terminal fixing (20 N) After test, resistance < 0,05 ull test of mechanical connection (50 N) After test, resistance < 0,05 Voltage drop test, resistance < 0, (4.28) Fixing of thermal sensing control Not plug-in or easily replaceable type Reliably kept in position No adhesive fixing if UV radiations from a lamp can degrade the fixing Not outside the luminaire enclosure Test of adhesive fixing: Max. temperature on adhesive material (C)... : 100 cycles between t min and t max Temperature sensing control still in position 1.6 (4.29) Luminaires with non-replaceable light source Not possible to replace light source Live part not accessible after parts have been opened by hand or tools 1.6 (4.30) Luminaires with non-user replaceable light source If protective cover provide protection against electric shock and marked with caution, electric shock risk symbol:

16 age 16 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Minimum two fixing means 1.6 (4.31) Insulation between circuits Circuits insulated from LV supply fulfil requirements according Controllable luminaires requiring same level of insulation for all components, the insulation between control terminals and LV supply fulfil requirements according (4.31.1) SELV circuits Used SELV source Voltage ELV Insulating of SELV circuits from LV supply Insulating of SELV circuits from other non SELV circuits Insulating of SELV circuits from FELV Insulating of SELV circuits from other SELV circuits SELV circuits insulated from accessible parts according Table X.1 lugs not able to enter socket-outlets of other voltage systems Socket outlets does not admit plugs of other voltage systems lugs and socket-outlets does not have protective conductor contact 1.6 (4.31.2) FELV circuits Used FELV source Voltage ELV Insulating of FELV circuits from LV supply FELV circuits insulated from accessible parts according Table X.1 lugs not able to enter socket-outlets of other voltage systems Socket outlets does not admit plugs of other voltage systems Socket-outlets does not have protective conductor contact 1.6 (4.31.3) Other circuits Other circuits insulated from accessible parts according Table X.1

17 age 17 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Class II construction with equipotential bonding for protection against indirect contacts with live parts: - conductive parts are connected together - test according of above - conductive part not cause an electric shock in case of an insulation fault - equipotential bonding in master/slave applications - master luminaire provided with terminal for accessible conductive parts of slave luminaires - slave luminaire constructed as class I 1.6 (4.32) Overvoltage protective devices Comply with IEC External to control gear and connected to earth: - only in fixed luminaires - only connected to protective earth 1.7 (11) CREEAGE DISTANCES AND CLEARANCES 1.7 (11.2) Creepage distances and clearances... : See Table 1.7 (11.2) Working voltage (V)... : V Rated pulse voltage (kv)... : Voltage form... : Sinusoidal Non-sinusoidal TI... : < 600 > 600 Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III 1.8 (7) ROVISION FOR EARTHING 1.8 ( ) Accessible metal parts Metal parts in contact with supporting surface Resistance < 0,5... : Functional earthing Self-tapping screws used Thread-forming screws Thread-forming screw used in a grove Earth makes contact first

18 age 18 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.8 ( ) Terminal blocks with integrated screwless earthing contacts tested according Annex V rotective earthing of the luminaire not via built-in control gear Earth continuity in joints, etc. 1.8 (7.2.4) Locking of clamping means Compliance with Terminal blocks with integrated screwless earthing contacts tested according Annex V 1.8 (7.2.5) Earth terminal integral part of connector socket 1.8 (7.2.6) Earth terminal adjacent to mains terminals 1.8 (7.2.7) Electrolytic corrosion of the earth terminal 1.8 (7.2.8) Material of earth terminal Contact surface bare metal 1.8 (7.2.10) Class II luminaire for looping-in Double or reinforced insulation to functional earth 1.8 (7.2.11) Earthing core coloured green-yellow Length of earth conductor 1.9 (14) SCREW TERMINALS Separately approved; component list... : (see Annex 1) art of the luminaire... : (see Annex 3) 1.9 (15) SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS Separately approved; component list... : (see Annex 1) art of the luminaire... : (see Annex 4) 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2) Supply connection and external wiring 1.10 (5.2.1) Means of connection... : Terminal Outdoor luminaire has not VC insulated external wiring if not class III or SELV 25 V a.c./60 V d.c. or protected from outdoor environment 1.10 (5.2.2) Type of cable... : IEC Nominal cross-sectional area (mm²)... : 3X1,0mm²

19 age 19 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Cables equal to IEC or IEC (5.2.3) Type of attachment, X, Y or Z 1.10 (5.2.5) Type Z not connected to screws 1.10 (5.2.6) Cable entries: - suitable for introduction - adequate degree of protection 1.10 (5.2.7) Cable entries through rigid material have rounded edges 1.10 (5.2.8) Insulating bushings: - suitably fixed - material in bushings - material not likely to deteriorate - tubes or guards made of insulating material 1.10 (5.2.9) Locking of screwed bushings 1.10 (5.2.10) 1.10 ( ) 1.10 ( ) 1.10 ( ) Cord anchorage: - covering protected from abrasion - clear how to be effective - no mechanical or thermal stress - no tying of cables into knots etc. - insulating material or lining Cord anchorage for type X attachment: a) at least one part fixed b) types of cable c) no damaging of the cable d) whole cable can be mounted e) no touching of clamping screws f) metal screw not directly on cable g) replacement without special tool Glands not used as anchorage Labyrinth type anchorages Adequate cord anchorage for type Y and type Z attachment Tests:

20 age 20 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - impossible to push cable; unsafe - pull test: 25 times; pull (N)... : 60 - torque test: torque (Nm)... : 0,25 - displacement 2 mm - no movement of conductors - no damage of cable or cord - function independent of electrical connection 1.10 (5.2.11) 1.10 (5.2.12) 1.10 (5.2.13) External wiring passing into luminaire Looping-in terminals Wire ends not tinned 1.10 (5.2.14) 1.10 (5.2.16) 1.10 (5.2.17) 1.10 (5.2.18) Wire ends tinned: no cold flow Mains plug same protection Class III luminaire plug No unsafe compatibility Appliance inlets (IEC 60320) Installation couplers (IEC 61535) Other appliance inlet or connector according relevant IEC standard No standardized interconnecting cables properly assembled Used plug in accordance with - IEC other standard 1.10 (5.3) Internal wiring 1.10 (5.3.1) Internal wiring of suitable size and type Through wiring - not delivered/ mounting instruction - factory assembled - socket outlet loaded (A)... : - temperatures... : (see Annex 2) Green-yellow for earth only

21 age 21 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.10 ( ) 1.10 ( ) 1.10 ( ) 1.10 ( ) 1.10 ( ) 1.10 ( ) Internal wiring connected directly to fixed wiring Cross-sectional area (mm²)... : 0,5-1,0 Insulation thickness Extra insulation added where necessary Internal wiring connected to fixed wiring via internal current-limiting device Adequate cross-sectional area and insulation thickness Double or reinforced insulation for class II Conductors without insulation SELV current-carrying parts Insulation thickness other than VC or rubber 24AWG 1.10 (5.3.2) Sharp edges etc. No moving parts of switches etc. Joints, raising/lowering devices Telescopic tubes etc. No twisting over (5.3.3) Insulating bushings: - suitable fixed - material in bushings - material not likely to deteriorate - cables with protective sheath 1.10 (5.3.4) Joints and junctions effectively insulated 1.10 (5.3.5) Strain on internal wiring 1.10 (5.3.6) Wire carriers 1.10 (5.3.7) Wire ends not tinned Wire ends tinned: no cold flow 1.11 (8) ROTECTION AGAINST ELECTRIC SHOCK 1.11 (8.2.1) Live parts not accessible Basic insulated parts not used on the outer surface without appropriate protection

22 age 22 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Basic insulated parts not accessible with standard test finger on portable, settable and adjustable luminaires Basic insulated parts not accessible with Ø 50 mm probe from outside, other types of luminaires Lamp and starterholders in portable and adjustable luminaires comply with double or reinforced insulation requirements Basic insulation only accessible under lamp or starter replacement rotection in any position Double-ended tungsten filament lamp Insulation lacquer not reliable Double-ended high pressure discharge lamp Relevant warning according to fitted to the luminaire 1.11 (8.2.2) ortable luminaire adjusted in most unfavourable position 1.11 (8.2.3.a) 1.11 (8.2.3.b) 1.11 (8.2.3.c) Class II luminaire: - basic insulated metal parts not accessible during starter or lamp replacement - basic insulation not accessible other than during starter or lamp replacement - glass protective shields not used as supplementary insulation BC lampholder of metal in class I luminaires shall be earthed SELV circuits with exposed current carrying parts: Ordinary luminaire: - touch current... : - no-load voltage... : Other than ordinary luminaire: - nominal voltage... : 1.11 (8.2.4) ortable luminaire have protection independent of supporting surface 1.11 (8.2.5) Compliance with the standard test finger or relevant probe 1.11 (8.2.6) Covers reliably secured

23 age 23 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.11 (8.2.7) Discharging of capacitors 0,5 F ortable plug connected luminaire with capacitor Other plug connected luminaire with capacitor Discharge device on or within capacitor Discharge device mounted separately 1.12 (12) ENDURANCE TEST AND THERMAL TEST 1.12 (-) If I > I 20 relevant test of (12.4), (12.5) and (12.6) after (9.2) before (9.3) specified in (12.3) Endurance test: 1.12 (12.3.2) - mounting-position... : Fixed mounted - test temperature (C)... : 45C - total duration (h)... : 240h - supply voltage: Un factor; calculated voltage (V)... : 1,1 x 240V=264,4V - lamp used... : Integral LED module After endurance test: - no part unserviceable - luminaire not unsafe - no damage to track system - marking legible - no cracks, deformation etc (12.4) Thermal test (normal operation) (see Annex 2) 1.12 (12.5) Thermal test (abnormal operation) (see Annex 2) 1.12 (12.6) Thermal test (failed lamp control gear condition): 1.12 (12.6.1) Through wiring or looping-in wiring loaded by a current of (A)... : - case of abnormal conditions... : - electronic lamp control gear - measured winding temperature (C): at 1,1 Un... : - measured mounting surface temperature (C) at 1,1 Un... : - calculated mounting surface temperature (C)... : - track-mounted luminaires

24 age 24 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.12 (12.6.2) Temperature sensing control - case of abnormal conditions... : - thermal link - manual reset cut-out - auto reset cut-out - measured mounting surface temperature (C)... : - track-mounted luminaires 1.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): 1.12 (12.7.1) 1.12 ( ) Luminaire without temperature sensing control Luminaire with fluorescent lamp 70W Test method or Annex W... : Test according to : - case of abnormal conditions... : - Ballast failure at supply voltage (V)... : - Components retained in place after the test - Test with standard test finger after the test Test according to Annex W: - case of abnormal conditions... : 1.12 ( ) - measured winding temperature (C): at 1,1 Un... : - measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : Ball-pressure test... : See Table 1.15 (13.2.1) Luminaire with discharge lamp, fluorescent lamp > 70W, transformer > 10 VA - case of abnormal conditions... : - measured winding temperature (C): at 1,1 Un... : - measured temperature of fixing point/exposed part (C): at 1,1 Un... : - calculated temperature of fixing point/exposed part (C)... : Ball-pressure test... : See Table 1.15 (13.2.1)

25 age 25 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.12 ( ) Luminaire with short circuit proof transformers 10 VA - case of abnormal conditions... : - Components retained in place after the test - Test with standard test finger after the test 1.12 (12.7.2) Luminaire with temperature sensing control - thermal link... : Yes No - manual reset cut-out... : Yes No - auto reset cut-out... : Yes No - case of abnormal conditions... : - highest measured temperature of fixing point/ exposed part (C):... : Ball-pressure test:... : See Table 1.15 (13.2.1) 1.13 (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE 1.13 (-) If I > I 20 the order of tests as specified in clause (9.2) Tests for ingress of dust, solid objects and moisture: - classification according to I... : I 65 - mounting position during test... : Fixed mounted - fixing screws tightened; torque (Nm) : - tests according to clauses : & electric strength test afterwards (see ) a) no deposit in dust-proof luminaire b) no talcum in dust-tight luminaire c) no trace of water on current-carrying parts or on insulation where it could become a hazard d) i) For luminaires without drain holes no water entry d) ii) For luminaires with drain holes no hazardous water entry e) no water in watertight luminaire f) no contact with live parts (I 2X) f) no entry into enclosure (I 3X and I 4X) f) no contact with live parts (I3X and I4X)

26 age 26 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict g) no trace of water on part of lamp requiring protection from splashing water h) no damage of protective shield or glass envelope 1.13 (9.3) Humidity test 48 h 25C; 93 %RH 1.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH 1.14 (10.2.1) Insulation resistance test Cable or cord covered by metal foil or replaced by a metal rod of mm Ø... : covered by metal foil 1.14 (10.2.2) Insulation resistance (M)... : SELV - between current-carrying parts of different polarity : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Other than SELV - between live parts of different polarity... : 1000M - between live parts and mounting surface... : 1000M - between live parts and metal parts... : 1000M - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Electric strength test Dummy lamp Luminaires with ignitors after 24 h test Luminaires with manual ignitors Test voltage (V)... : 1480V SELV

27 age 27 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict - between current-carrying parts of different polarity : - between current-carrying parts and mounting surface... : - between current-carrying parts and metal parts of the luminaire... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : Other than SELV - between live parts of different polarity... : 1480V - between live parts and mounting surface... : 1480V - between live parts and metal parts... : 1480V - between live parts of different polarity through action of a switch... : - between the outer surface of a flexible cord or cable where it is clamped in a cord anchorage and accessible metal parts... : - Insulation bushings as described in Section 5... : 1.14 (10.3) Touch current or protective conductor current (ma) : 0,5 ma 1.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING 1.15 (13.2.1) 1.15 (13.3.1) 1.15 (13.3.2) Ball-pressure test... : See Test Table 1.15 (13.2.1) Needle-flame test (10 s)... : See Test Table 1.15 (13.3.1) Glow-wire test (650C)... : See Test Table 1.15 (13.3.2) 1.15 (13.4) roof tracking test (IEC 60112)... : See Test Table 1.15 (13.4)

28 age 28 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.7 (11.2) TABLES: Creepage distances and clearances Table 11.1 Minimum distances (mm) for a.c. (50/60 Hz) sinusoidal voltages RMS working voltage (V) not exceeding Creepage distances Required basic insulation, TI 600 0,6 0,8 1, ,5 Measured Required basic insulation, TI < 600 1,2 1,6 2, Measured L, N 3 Required supplementary insulation TI 600-0,8 1, ,5 Measured Required supplementary insulation TI < 600-1,6 2, Measured Required reinforced insulation - 3, Measured Clearances Required basic insulation 0,2 0,8 1, ,5 Measured L,N 3 Required supplementary insulation - 0,8 1, ,5 Measured Required reinforced insulation - 1, Measured Table 11.2 Minimum distances (mm) for non-sinusoidal pulse voltages Rated pulse voltage (peak kv) 2,0 2,5 3,0 4,0 5,0 6,0 8,0 Required clearances 1,0 1, ,5 8 Measured Rated pulse voltage (peak kv) Required clearances Measured Rated pulse voltage (peak kv) Required clearances Measured

29 age 29 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.15 (13.2.1) TABLE: Ball ressure Test of Thermoplastics Allowed impression diameter (mm)... : 2mm Object/ art No./ Material Manufacturer/ trademark Test temperature (C) Enclosure See annex ,9 lampshade See annex ,6 Connector on LED module See annex ,2 Gland See annex ,8 Supplementary information: Impression diameter (mm) 1.15 (13.3.1) Object/ art No./ Material Connector on LED module TABLE: Needle-flame test (IEC ) Manufacturer/ trademark Duration of application of test flame (ta); (s) Ignition of specified layer Yes/No Duration of burning (tb) (s) Verdict See annex 1 10s No 20s Supplementary information: 1.15 (13.3.2) TABLE: Glow-wire test (IEC ) Glow wire temperature... : 650 C Object/ art No./ Material Manufacturer/ trademark Duration of application of test flame (ta); (s) Ignition of specified layer Yes/No Duration of burning (tb) (s) Enclosure See Annex 1 30s No 5s lampshade See Annex 1 30s No 5s Gland See Annex 1 30s No 5s Any flame or glowing of the sample extinguished within 30 s of withdrawing the glow-wire, and any burning or molten drop did not ignite the underlying parts (Yes/No)... : Supplementary information: Verdict Yes

30 age 30 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict 1.15 (13.4) TABLE: roof tracking test (IEC 60112) Test voltage TI... : 175 V Object/ art No./ Material Manufacturer/ trademark Withstand 50 drops without failure on three places or on three specimens Verdict Supplementary information: ANNEX 1 TABLE: Critical components information Object / part No. Code Manufacturer/ trademark Type / model Technical data Standard Mark(s) of conformity 1) Terminal B Yuyao Yunhuan Ruixin Electronics Co., Ltd. AS02 AC450V, 0,5 1,5mm², 3 poles, T85, 100A IEC VDE Alternative D Ningbo Economic & Technical Development Zone Hengda Electrical Co., Ltd. TB-7020B/3 AC450V, 0,75 2,5mm², 3 poles, T110, 16A EN TUV Rheinland Alternative D Yuyao Yunhuan Ruixin Electronics Co., Ltd. AS02-5 AC450V, 0,5 1,5mm², 5 poles, T85, 100A IEC VDE Alternative D Ningbo Economic & Technical Development Zone Hengda Electrical Co., Ltd. TB-7020B/5 AC450V, 0,75 2,5mm², 5 poles, T110, 16A EN TUV Rheinland Internal wire (input of LED driver) B Ningbo A-Line Cable and Wire Co., Ltd. H05V-U, H05V-K 1x0,5 1,0mm² IEC VDE Alternative D Cixi Hongyu Electric Appliance Co., Ltd. H05V-U, H05V-K 1x0,5 1,0mm² IEC VDE Alternative D Cixi Hongxin Wire and Cable Factory H05V-U, H05V-K 1x0,5 1,0mm² IEC VDE

31 age 31 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Alternative D Tongxiang Xintianhong Wire and Cable Factory H05V-U, H05V-K LED driver B hilips Xitanium 36W A 115V 230V LED driver B hilips Xitanium 75W A 220V 230V LED driver B hilips Xitanium 75W A 215V TD 230V Internal wire (output of LED driver) C MOLEX INCORORATE D Alternative C JAAN SOLDERLESS TERMINAL MFG CO LTD LED module C Lejin Electronics products(huizhou ) CO., Ltd LED module C Lejin Electronics products(huizhou ) CO., Ltd Earth wire B Ningbo A-Line Cable and Wire Co., Ltd. Alternative D Cixi Hongyu Electric Appliance Co., Ltd. Alternative D Cixi Hongxin Wire and Cable Factory Heat shrinkable sleeve C SHENZHEN WOER HEAT- SHRINKABLE MATERIAL CO LTD 1x0,5 1,0mm² IEC Test with appliance V, 50 60Hz, Uout: Vdc, 36W, Iout: A V, 50 60Hz, Uout: Vdc, 75W, Iout: A V, 50 60Hz, Uout: Vdc, 75W, Iout: A IEC IEC IEC NL NL NL AWG IEC Test with appliance UL (E29179) THB 24AWG IEC Test with appliance UL (E60389) Fortimo LED line Fortimo LED line H05V-K H05V-U H05V-U, H05V-K H05V-U, H05V-K Imax: 560mA, Umax: 38V Imax: 400mA, Umax: 70V IEC IEC Test with appliance Test with appliance 1x0,5 1,0mm² IEC VDE x0,5 1,0mm² IEC VDE 1x0,5 1,0mm² IEC VDE RSFR-H 600V, 125ºC IEC Test with appliance UL (E203950)

32 age 32 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Gland C SHANGHAI WEYER ELECTRIC ALIANCES CO LTD HSK-13.5G 6-12mm IEC Test with appliance UL (E316890) Supplementary information: 1) rovided evidence ensures the agreed level of compliance. See OD-CB2039. The codes above have the following meaning: A B C D - The component is replaceable with another one, also certified, with equivalent characteristics - The component is replaceable if authorised by the test house - Integrated component tested together with the appliance - Alternative component ANNEX 2 TABLE: Temperature measurements, thermal tests of Section 12 Type reference... : BCW098 LED20/NW SU L600 Lamp used... : Integral LED module Lamp control gear used... : Xitanium 36W A 115V 230V Mounting position of luminaire... : Fixed mounting Supply wattage (W)... : 20,87 Supply current (A)... : 0,09 Calculated power factor... : 0,9 Table: measured temperatures corrected for ta = 35 C: - abnormal operating mode... : - test 1: rated voltage... : - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 1,06 X240V=254,4V 264V art Ambient Temperature measurements, (C) Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Supply cord ,

33 age 33 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict Supply cord (stress) , Terminal , Internal wire , tc , ,8 85 Enclosure ,7 -- Ref lampshade ,8 -- Ref Connector on LED module ,1 -- Ref LED module ,3 -- Ref Gland ,9 -- Ref Mounting surface Supplementary information: , ,1 130 Type reference... : BCW098 LED40/NW SU L1200 Lamp used... : Integral LED module Lamp control gear used... : Xitanium 75W A 220V 230V Mounting position of luminaire... : Fixed mounting Supply wattage (W)... : 39,65 Supply current (A)... : 0,16 Calculated power factor... : 0,9 Table: measured temperatures corrected for ta = 35 C: - abnormal operating mode... : - test 1: rated voltage... : - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 1,06 X240V=254,4V 264V Temperature measurements, (C) art Ambient Clause 12.4 normal Clause 12.5 abnormal

34 age 34 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict test 1 test 2 test 3 limit test 4 limit Supply cord , Supply cord (stress) , Terminal , Internal wire , tc , ,3 85 Enclosure ,1 -- Ref lampshade ,8 -- Ref Connector on LED module ,2 -- Ref LED module ,2 -- Ref Gland ,3 -- Ref Mounting surface Supplementary information: , ,3 130 Type reference... : BCW098 LED40/CW SD L1200 Lamp used... : Integral LED module Lamp control gear used... : Xitanium 75W A 215V TD 230V Mounting position of luminaire... : Fixed mounting Supply wattage (W)... : 39,69 Supply current (A)... : 0,16 Calculated power factor... : 0,9 Table: measured temperatures corrected for ta = 35 C: - abnormal operating mode... : - test 1: rated voltage... : - test 2: 1,06 times rated voltage or 1,05 times rated wattage... : - test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage... : - test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or looping-in wiring loaded by a current of A during the test... : 1,06 X240V=254,4V 264V

35 age 35 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict art Ambient Temperature measurements, (C) Clause 12.4 normal Clause 12.5 abnormal test 1 test 2 test 3 limit test 4 limit Supply cord , Supply cord (stress) , Terminal , Internal wire , tc , ,0 85 Enclosure ,7 -- Ref lampshade ,2 -- Ref Connector on LED module ,8 -- Ref LED module ,4 -- Ref Gland ,0 -- Ref Mounting surface Supplementary information: , ,5 130

36 age 36 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict ANNEX 3 Screw terminals (part of the luminaire) (14) SCREW TERMINALS (14.2) Type of terminal...: Rated current (A)...: ( ) One or more conductors ( ) Special preparation ( ) Terminal size Cross-sectional area (mm²)...: (14.3.3) Conductor space (mm)...: (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) Nominal diameter of thread (metric ISO thread)...: M External wiring No soft metal (14.4.5) Corrosion (14.4.6) Nominal diameter of thread (mm)...: Torque (Nm)...: (14.4.7) Between metal surfaces Lug terminal Mantle terminal ull test; pull (N)...: (14.4.8) Without undue damage ANNEX 4 Screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS (15.2) Type of terminal...: Connector Rated current (A)...: (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors

37 age 37 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position ( ) Conductor size Type of conductor (15.5.1) Terminals internal wiring ( ) ull test spring-type terminals (4 N, 4 samples)... : ( ) ull test pin or tab terminals (4 N, 4 samples)... : 4N, 1min Insertion force not exceeding 50 N ( ) ermanent connections: pull-off test (20 N) (15.5.2) Electrical tests Voltage drop (mv) after 1 h (4 samples)... : Max. 0,7mV Voltage drop of two inseparable joints Number of cycles: 25 cycles Voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : Voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)... : After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)... : Max.0,9mV / Max.1,1mV (15.6) Terminals external wiring Terminal size and rating ( ) ull test spring-type terminals or welded connections (4 samples); pull (N)... : ull test pin or tab terminals (4 samples); pull (N)... : ( ) TABLE: Contact resistance test Voltage drop (mv) after 1 h terminal voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... :

38 age 38 of 54 Report No.: IEC Clause Requirement + Test Result - Remark Verdict terminal voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : 22,5 terminal voltage drop (mv) 1,1 1,3 1,3 1,4 1,3 1,4 1,4 1,4 1,2 1,3 Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) Supplementary information:

39 age 39 of 54 Report No.: IEC60598_2_1D Appendix 1 Clause Requirement + Test Result - Remark Verdict ATTACHMENT TO TEST REORT IEC EUROEAN GROU DIFFERENCES AND NATIONAL DIFFERENCES Luminaires art 2: articular requirements Section 1: Fixed general purpose luminaires Differences according to... : EN :1989 used in conjunction with EN :2015 Annex Form No....: EU_GD_IEC60598_2_1D Annex Form Originator...: OVE Master Annex Form...: Copyright 2015 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. CENELEC COMMON MODIFICATIONS (EN) 1.5 (3) MARKING 1.5 ( ) For luminaires not supplied with terminal block: Adequate warning on the package 1.6 (4) CONSTRUCTION 1.6 (4.11.6) Electro-mechanical contact systems 1.10 (5) EXTERNAL AND INTERNAL WIRING 1.10 (5.2.1) Connecting leads - without a means for connection to the supply - terminal block specified - relevant information provided - compliance with 4.6, 4.7.1, 4.7.2, , 11.2, 12 and 13.2 of art (5.2.2) Cables equal to EN Replace table 5.1 Supply cord 1.12 (12) ENDURANCE TESTS AND THERMAL TESTS 1.12 (12.4.2c) Thermal test (normal operation) see footnote c to table 12.2 relating to unsleeved fixed wiring

40 age 40 of 54 Report No.: IEC60598_2_1D Appendix 1 Clause Requirement + Test Result - Remark Verdict ZB ANNEX ZB, SECIAL NATIONAL CONDITIONS (EN) (3.3) DK: power supply cords of class I luminaires with label (4.5.1) DK: socket-outlets (5.2.1) CY, DK, FI, GB: type of plug ZC ANNEX ZC, NATIONAL DEVIATIONS (EN) (4 & 5) FR: Shuttered socket-outlets 10/16A FR: Safety requirements for high buildings (Arrêté du 30 décembre 2011 portant règlement de sécurité pour la construction des immeubles de grande hauteur et leur protection contre les risques d incendie et de panique; Section VIII; Article GH 48, Eclairage) Glow-wire test for outer parts of luminaires: - 850C for luminaires in stairways and horizontal travel paths - 650C for indoor luminaires GB: Requirements according to United Kingdom Building Regulation

41 age 41 of 54 Report No.: Appendix 2 Additional requirements of EN Clause Requirement + Test Result - Remark Verdict 6 CLASSIFICATION Built-in module... : Yes No Independent module... : Yes No Integral module... : Yes No For Integral module; Note to in IEC applies Module withstands overpower condition >15 min. 150% rated voltage, thermally stabilised Module with automatic protective device or power limiter, test performed 15 min. at limit. During the tests, tissue paper, spread below module, does not ignite 14 TABLE: tests of fault conditions art Simulated fault Hazard LED bulb Short circuit: Lighting not work No

42 age 42 of 54 Report No.: Appendix 3 hotograph SU L600 SU L1200 SD L1200 Over view Bottom view

43 age 43 of 54 Report No.: Appendix 3 hotograph Gland 1 Gland 2

44 age 44 of 54 Report No.: Appendix 3 hotograph Side view Open view of BCW098 LED20/NW SU L600, BCW098 LED20/CW SU L600

45 age 45 of 54 Report No.: Appendix 3 hotograph Terminal Earth connection

46 age 46 of 54 Report No.: Appendix 3 hotograph LED module LED module

47 age 47 of 54 Report No.: Appendix 3 hotograph LED module Open view of BCW098 LED40/NW SU L1200, BCW098 LED40/CW SU L1200

48 age 48 of 54 Report No.: Appendix 3 hotograph Terminal Earth connection

49 age 49 of 54 Report No.: Appendix 3 hotograph LED module LED module

50 age 50 of 54 Report No.: Appendix 3 hotograph LED module LED module

51 age 51 of 54 Report No.: Appendix 3 hotograph Open view of BCW098 LED40/NW SD L1200, BCW098 LED40/CW SD L1200 Terminal

52 age 52 of 54 Report No.: Appendix 3 hotograph LED module LED module

53 age 53 of 54 Report No.: Appendix 3 hotograph LED module LED module

54 age 54 of 54 Report No.: Appendix 3 hotograph Fixed screw