Double Effect Exhaust Gas Driven Absorption Machine

Transcription

1 For Future Energy & Environment erformance Data Double Effect Gas Driven Absorption Machine Double Effect Gas Driven ype (50~R) Unit CH005 CH006 CH007 CH008 CH010 CH012 CH015 CH018 CH021 CH024 CH028 CH032 CH036 CH040 Capacity usr Inlet emp./outlet emp. 12 / 7 Chilled Inlet emp./outlet emp. 32 / Heating Capacity Mcal/h Inlet emp./outlet emp / 60 Hot ton/h kg/sec / 165 emp. Heating 450 / 125 Gas ressure Drop m Inlet Conn. mm *mm 782 * * * * * * * * * * * * * *759 Outlet Conn mm Diverter Valve mm ower source Abs. ump (5.5) 3ø, V, 50Hz 2.0 () 2.4 (6.9) 3.2 (9.0) Ref. ump 0.2 (1.0) () () Electric urge ump Sealing Blower Control anel () (2.5) 0.2 (0.5) Amp.(Vac) A Lenght (L) mm 2 2 2,638 3,6 3,717 4,742 4,872 Size Width (W) mm 1,683 1,722 1,761 1, 1,857 1,935 2,052 2,091 2,194 2,194 2,310 2,349 2,349 2,349 Height (H) mm 1 2,090 2,147 2,399 Weight Rigging ton Operation ton te 1. Working pressure of each water side is based on 1.0Ma (psig). 2. Lowest outlet temperature of chilled water is 5 o C and 18 o C for cooling water. 3. Controllable cooling capacity range shall be 25~% as a standard condition and 0~% as an option. 4. Each water flow can be adjusted within 50~120%. 5. Fouling factor m 2.h. o C/kcal for Absorber and Condenser, m 2.h. o C/kcal for Evaporator and Generator o C of hot-water temperature is possible as an option.

2 CH Series WORLD ENERGY Double Effect Gas Driven Absorption Machine erformance Data Double Effect Gas Driven ype (450~1R) Unit CH045 CH050 CH056 CH063 CH070 CH0 CH090 CH CH110 CH120 CH130 CH140 CH Chilled Capacity Inlet emp./outlet emp. usr / Inlet emp./outlet emp. 32 / Hot Heating Capacity Inlet emp./outlet emp. Mcal/h ton/h / kg/sec / emp. Heating 450 / 125 Gas ressure Drop m Inlet Conn. mm *mm 1376 * * * * * * * * * * * * *2068 Outlet Conn Diverter Valve mm mm ower source 3ø, V, 50Hz Abs. ump 3.2 (9.0) 5.5 (15.0) 7.5 (24.0) Ref. ump () (4.0) Electric urge ump () 5 (2.2) Sealing Blower Control anel Amp.(Vac) Lenght (L) A mm ,954 4, ,540 6,038 5,644 (2.5) 0.2 (0.5) ,142 6,667 6,293 6, ,318 6,974 7,475 Size Width (W) mm 2,491 2,569 2,934 3,069 3,159 3,330 3,4 3,530 4,348 4,448 4,598 4,932 5,182 Height (H) mm 2,633 2,962 3,3 3, 3,700 Weight Rigging ton Operation ton CH erformance Data te 1. Working pressure of each water side is based on 1.0Ma (psig). 2. Lowest outlet temperature of chilled water is 5 o C and 18 o C for cooling water. 3. Controllable cooling capacity range shall be 25~% as a standard condition and 0~% as an option. 4. Each water flow can be adjusted within 50~120%. 5. Fouling factor m 2.h. o C/kcal for Absorber and Condenser, m 2.h. o C/kcal for Evaporator and Generator o C of hot-water temperature is possible as an option.

3 I For Future Energy & Environment Double Double Effect Effect Gas Driven Gas Driven Absorption Absorption Chiller Machine and Heater Foundation K/2 A H Nut Anchor Bolt Steel late F Absorber, Evaporator, Condenser & Low emperature Generator Shell Assembly F B Welding Machine Feet J/2 J E Example of Anchoring K te 1. Drain ditch should be prepared around foundation. 2. Horizontal level of foundaton surface should be maintained less than 1mm per 1m. 3. indicates the location of anchor bolts. (Anchor bolt, nut and steel plates are not supplied) G High emperature Generator Assemply G D Drain Ditch Foundation 50 C CH005 CH006 CH007 CH008 CH010 CH012 CH015 CH018 CH021 CH024 CH028 CH032 CH036 CH040 CH045 CH050 CH056 CH063 CH070 CH0 CH090 CH CH110 CH120 CH130 CH140 CH A 1,421 1,921 1,941 2,961 2,936 3,956 3,906 3,856 4,398 4,896 4,348 4,846 5,371 4,896 5,421 5,921 5,371 5,871 B 700 1, , 1,210 1,290 1, C 973 1,033 1,194 1,307 1,453 1,386 1,404 1,567 1,370 1, 2, 2, D ,000 1, 1, 1, 1, 1, 1, 1, 1,700 1, 2, E ,171 1,171 1,146 1,131 1,106 H I J K F (ton) G (ton)

4 CH Series WORLD ENERGY Double Effect Gas Driven Absorption Machine System ipings 1 Air Handling Unit Expansion ank gas Inlet Gas Bypass Diverter Valve gas Outlet Air Engine Fuel Supply water Air vent AV Bleed off ower Drain line CH Foundation / System ipings Chilled / Hot water ump (2nd) Chilled / Hot Flow meter water ump (1st) F Bypass valve D water Outlet Chilled water Outlet Chilled water Inlet water Inlet hermostat ressure gauge emperature Gauge Damper valve Bypass valve Strainer Valve ABSORION CHILLER water ump Supply Header Return Header 1) All external equipment out of dotted line is scope of customer's. 2) Refer to outline drawing and specification data sheet for the external dimensions of the machine, the location & the diameter of water pipe connection and the dimensions & the size of gas line connections. 3) he locations of chilled water pumps, cooling water pumps and expansion tanks shall be determined in consideration of the hydrostatic head of pumps and the height of building. And the Machine shall not be subject to a pressure higher than the designed pressure at any water header. 4) For cooling water quality control, it is recommended to install cooling water bleed-off device on the inlet pipe line of cooling towers. 5) Around 10 meshes of strainers are recommended to be installed in the cooling water line. 6) For the maintenance and the inspection of the Machine, the following equipment shall be installed on each chilled water and cooling water inlet/outlet lines as well as stop valve. hermometers and pressure gauges shall be installed at chilled and cooling water inlet/outlet. Air relief valves shall be installed on each chilled and cooling water lines at higher points than each water headers. Drain valves shall be installed at the lowest position between the stop valves of chilled and cooling water and the Machine and the drain valve shall be piped to the drain ditch. 7) here shall be a sufficient clearance for access to the absorber, evaporator, condenser, and generator to facilitate inspection and cleaning work. Diverter Valve & Gas Duct For Diverter Valve; 1) Install the diverter valve at the exhaust gas duct end of gas turbine or reciprocating engine and level the diverter valve horizontally by using the level gauge. 2) Install the transient duct between high-stage generator and diverter valve. 3) Connect the wiring in accordance with wiring diagram of the manufacturer. Duct High Stage Generator Vertical Duct Bypass Diverter Valve Gas For Gas Duct; 1) Sharp bend and restrictions should be avoided to allow smooth gas flow. 2) he exhaust gas duct outlet should be arranged to prevent the rain water from entering into the machine and the drain connection should be provided to remove the condensate from the exhaust gas outlet side.

5 For Future Energy & Environment Double Effect Gas Driven Absorption Machine hermal Insulation Hot Surface 75mm : High emp. Generator 50mm : High Heat Exchanger Box with High emperature iping, Steam box 19mm : Heat Exchanger Body with Low emperature Box, Low temperature Generator Body with Outlet Box 10mm : Low temperature iping Cold Surface 19mm : Evaporator Body with Box 10mm : Inlet and Outlet iping of Refrigerant ump te 1. Use only n-inflammable or Incombustible insulation materials. 2. Do not insulate motor of refrigerant pump. 3. otal insulation area includes piping. 4. Do not cover components such as service valves, dampers, diaphragm valves, sight glass, control valves or thermometers or sensor wells. 5. he standard Material and hickness as the recommendation : HO Surface insulation Material of insulation : Glass wool, hermal Conductivity 0.04kcal/m h hickness of insulation : 50mm (2 inch), 75mm (3 inch) Material of insulation : Closed cell type n-inflammable polymer sponge hickness of insulation : 10mm (3/8inch), 19mm (3/4inch) COLD Surface insulation Material of insulation : Closed cell type n-inflammable polymer sponge hickness of insulation : 10mm (3/8 inch), 19mm (3/4 inch) CH005 CH006 CH007 CH008 CH010 CH012 CH015 CH018 CH021 CH024 CH028 CH032 CH036 CH040 75mm Hot Surface (m 2 ) 50mm 19mm Wrapping Material when Glass wool is used. Insulated parts on body : Colored galvanized steel with 5mm thickness or over Insulated parts on pipes : Colored galvanized steel with 0mm thickness or over 6. For insulation area for each model, please refer to the picture below. 7. he water box sections should be worked to be disassembled for the repair. 8. If necessary, please perform the finish painting in the field after completing World the insulation Energy work. Co.,LD. Cold Surface (m 2 ) Hot Surface (m 2 ) 10mm 19mm 10mm 75mm 50mm 19mm CH CH CH056 CH063 CH070 CH0 CH090 CH CH110 CH120 CH130 CH140 CH mm Cold Surface (m 2 ) 19mm 10mm

6 CH Series WORLD ENERGY Double Effect Gas Driven Absorption Machine Start-up Sequence Start Chilled ump Start Request Verify All sensors in range In restart safties Mode 60 deg C Heating Sensor Fault / restart Alerts 79 deg C Heating 1 CH hermal Insulation / Start-up Sequence Start Verify imer A B Verify Chilled Flow Verify timer elapsed Chilled Fault Start-Stop Condition Monitor for Start-Stop Start 3 min Refrigerant ump Delay imer Start ump Ref ump imer elapsed Start Verify imer Verify Flow timer Elapsed Fault Start Refrigerant ump Start ower Control Start Solution ump Machine Running