ARIES. 3,9mín 0,5 ( ph < 4)

Transcription

1 DESCRIPTION Safety shoes for professional use. Leather: Split leather Inner neck lining Coolmax Internal lining: Light rock. Removable inner sole Closing: hooks and laces Sole: Bidensity poliurethane + VIBRAM rubber layer Sizes: 38-47

2 GREY SPLIT LEATHER TEST RESULTS REQUIREMENTS Thickness mm - Tear Strength >180 N > 120 N Tensile Strength >22 N/mm 2 >15 N/mm 2 Water vapour permeability 10 mg/cm 2 h 0,8 mg/cm 2 h Water vapour coefficient 70mgr/cm 2 15 mgr/cm 2 ph Value Índice de diferencia 3,9mín 0,5 ( ph < 4) 3,5 mín 0,7 (ph < 4) Time with no water penetration > 120 min. N/A Water Absorption in 2 hours 15% N/A Wicking effect after 120 minutes 0 mm N/A Resistance between union upper-sole > 5,5 N/mm. >4,0 N/mm. INNER NECK LINING COOLMAX Technical fabric that speeds up the process of moisture absorption, ensuring the skin is always dry. Moisture is continually drawn to the exterior and never returns to the skin, creating a pleasant and comfortable sensation. Main characteristics: - Moisture control and quick drying - Lowers skin temperature - Soft, light and breathable - 100% absorbent and abrasion resistant TEST RESULTS REQUIREMENTS EN ISO Composition 65% PES + 35% COOLMAX - Tear Strength >32 N > 15 N Water vapour permeability >70 mg/cm 2 h 2 mg/cm 2 h Water vapour coefficient > 500 mgr/cm 2 20 mgr/cm 2 Abrasion resistance > cycles no damage > cycles no damage > cycles no damage > cycles no damage

3 GORE-TEX WATERPROOF AND BREATHABLE LINNING The Gore-Tex membrane provides permanent waterproofing and transpiration to safety footwear. FAL Footwear's, with Gore-Tex, combines the most advanced technological developments with materials of the finest quality. For this reason they have undergone a whole range of field and laboratory tests according to EEC regulations and the strict quality controls carried out by W.L. Gore & Partners and FAL Footwear. Thanks to this combination, this boot provides perfect protection and comfort to the user, preventing humidity from entering the boot and at the same time allowing sweat from exiting the foot. Gore-Tex Lining form a bootie where all their seams are sealed by a Hot Air Sealing System at 450ºC to prevent water from entering through them. GORE TEX MEMBRANE LAYERS COMPOSITION 1) Shell fabric: Warp knit 70%PA-30% PES (+- 5%) 2) Middle layer: Functional nonwoven 100% PES 3) Membrane : Bicomponent based on eptfe (100% PTFE) 4) Backing fabric: knit 100% PA TEST GORE TEX MEMBRANE REQUESTS RESULTS Thickness (EN ISO 5084) N/A 1,0±0,15mm Weight (DIN EN 12127) N/A 300±20g/m 2 Tear Strength >15 N > 95 N Abrasion resistance (EN ISO 20344) > cycles > cycles > cycles > cycles Water Vapour permeability > 2,0 mgrs/cm 2 hour > 6 mgrs/cm 2 hour Water vapour coefficient > 20 mgrs/cm 2 > 50 mgrs/cm 2 Resistance to water penetration (DIN EN 20811) > 1000mbar >5000 mbar Water Vapour Resistance (Ret) DIN EN 31092/ISO < 15 m 2 Pa/W Thermal Resistance (Rct) DIN EN 31092/ISO < 20 x10-3 m 2 K/W Colour fastness(iso 105/X12) > 4 5 Ret = The lower the figure is, the higher its Water vapour permeability will be (more breathable).

4 R et 5 Very good 5 R et 20 Good 20 R et 35 Acceptable > 35 Not Sufficient Rct = Larger thermal resistance means better thermal insulation and capability to keep the wearer warm. REMOVABLE INSOLE Removable insole anatomically preformed to provide total comfort to the feet. Anatomical and breathable insoles that provide excellent shock absorbing, eliminate moisture caused by perspiration, offer maximum comfort and guarantee total hygiene, thanks to their antibacterial treatment and active carbon, and antistatic composition. The first layer is made of very breathable 100% polyester, very soft but with a high abrasion resistance. The second layer is made of recycled rubber, open-cell foam that keeps feet dry (the special moisture absorption system keeps feet dry), well-ventilated and providing excellent comfort properties to the whole feet, and especially in the heel area. The cushioning system prevents foot fatigue and the foam last longer thanks to its inbuilt recovery system. TESTS RESULTS REQUIREMENTS Thickness >2 mm (on request) >2 mm Water absorption 173 mg/cm 2 70mg/cm 2 Water desorption 100% > 80 % Abrasion resistance > cycles > cycles (Cycles without break) >25600 >12800 SOLE Vibram Stone, this sole is an exclusive Vibram sole made only for FAL. The sole combines PU- Rubber materials. The PU in the midsole provides comfort, sock absorption, lightness. The rubber Vibram sole in the bottom provides hardness, abrasion protection and more other properties of Vibram rubber sole.

5