THERMOSTAT i-basic 3 USER MANUAL Rev.100

Transcription

1 USER MANUAL

2 Thank you for trusting the Hitecsa Products. Our company has been offering the market an extended range of specialized units for air conditioning and cooling installations for over 35 years. Our approach is based on efficiency, adaptability, usability and practical solutions. This has been the hallmark of our product catalogue. The versatility of our factory allows us to contribute solutions, almost tailored to each project s specifications, in search of a solution to every problem that arises in design and implementation of air conditioning installations. From all of us at Hiplus Aire Acondicionado, once again, thank you very much.

3 ÍNDICE... 4 MAIN FUNCTIONS... 4 Installation... 4 APPLICATIONS... 4 OPERATION... 4 I-BASIC SIMPLIFIED INTERNAL DIAGRAM... 5 WIRES COLOR FOR ON BOARD INSTALLATION... 6 Electrical diagrams... 7 Electronic control... 9 On board installation Wall installation DIP-Switch function (back of the thermostat) Led function

4 Electronic thermostat for fan coil MAIN FUNCTIONS - Room temperature adjustment - Manual or automatic Heating/Cooling selection - Manual and automatic 3 speed setting - Programmability through micro switch of the functions: destratification, fan mode, system type (2/4 pipes), electrical heater mode, neutral zone value. Installation - Wall-mounted (surface mounting with centres for box 503) - Directly on the fan coil (only AIR units) - Power supply 230 Vac 50 Hz - Output: 1A 230 Vac APPLICATIONS Suitable for: - 2-pipe system - 2-pipe system + On/off or floating valve - 2-pipe system + valve and electric heater - 4-pipe system + 2 on/off valves with neutral zone OPERATION 1. 2 pipe fan coil with valve: the thermostat controls both the fan and the valve according to the desired temperature. If water sensor is present, the fan is overridden according to the water temperature (warm and cold start function) pipe fan coil with valve: the thermostat drives both the fan and the valve based on the desired temperature pipe fan coil with valve and electrical heater: the thermostat controls the fan, the valve and the electrical heater according to the desired temperature pipe fan coil with two valves: the heating or cooling function is automatically determined by the neutral zone. The thermostat controls the heat valve in heating mode and the cold valve in cooling mode. If closes the valves when room temperature of system (warm and cold functions). During the installation, it is possible to choose between fans continuously running or fan thermostatic control. 4

5 SIMPLIFIED INTERNAL DIAGRAM 5

6 WIRES COLOR FOR ON BOARD INSTALLATION 6

7 i-basic3 Electrical diagrams LEGEND L = phase Vac N = neutral 230 Vac M = motor 230 Vac I = speed min II = speed med III = speed max Com = common motor KA1 = electric heater on/off relay XA1 = terminal board i-basic 3 YV1 = heat/cool valve 230 Vac on/off YV2 = heat valve 230 Vac on/off YV3 = cool valve 230 Vac on/off 7

8 i-basic3 Electrical diagrams LEGEND L = Phase 230 Vac N = Neutral 230 Vac M1 = Fan motor 230 Vac I = Speed min II = Speed med III = Speed max XA1 = Terminal board i-basic 3 YV5 = Heat/cool valve floating (3 point) 230 Vac 8

9 i-basic3 Electronic control LEGEND A1 = YV6 = YV7 = YV8 = Motor with electronic control 0-10 VDC Heat/Cool valve 0-10 VDC modulating Heat valve 0-10 VDC modulating Cool valve 0-10 VDC NOTE: 1. Not short the J9 pins not used 2. Pins 4 and 5 should never be wired (only factory used) 3. Motor regulation with electronic control: - Speeds switch in the position I = out fix 3VDC - Speeds switch in the position II = out fix 6VDC - Speeds switch in the position A: If DIP 5 = OFF the output is variable according to the set-point and room temperature (fan off with set point reached) Si DIP 5 = ON the output is variable according to the set-point and room temperature (fan at minimum speed with set point reached 1,5 VDC) 9

10 Electronic control OPEN = Cooling CLOSED = heating Air temperature sensor NTC10K@25ºc Always be used in case of the board installation The sensors recognized automatically by the thermostat. With the remote air sensor connected is active the destratification cycle: the fan operate for 90 sec. at minimum speed every 15 minutes. Water sensor temperature NTC10K@25ºC 1. In the case of automatic change over with 2 pipe System and 3 way valve, the sensor is positioned upstream of the valve. 2. In the case of 4 pipe System the sensor is positioned in the heating coil ECONOMY OPEN = Confort CLOSED = Economy In economy mode is set a fixed temperature: 17ºC Heating mode 28ºC Cooling mode WINDOW OPEN = Fan OFF = Valve closed CLOSED = Confort 10

11 On board installation Wall installation Note for installation: 1) The thermostat is composed of two parts: the base with the terminal and the electronics control. For easy installation the two parts are supplied separately (dropped). After the electrical connections on the terminal in the base, the two parties must be joined by 4 clips on the four corners: insertion of 4 teeth of 4 slots (picture B). 2) The base standard is designed for mounting with Italian wall box (type 503). It is possible replace the standard base with another base (accessory) for wall-mounted (picture C). 11

12 DIP-Switch function (back of the thermostat) Nº DIP FUNCTION OFF ON 1 2/4 Pipe system 2 pipe 4 pipe 2 Heating / Cooling switching Manual Automatic or centralized if DIP 7 = ON 3 DIP 3 = OFF DIP 4 = OFF DIP 3 = ON DIP 4 = ON No electric Heater No electric Heater Electric heater (combination of DIP 3 and DIP 4) DIP 3 = ON DIP 4 = OFF Electric heater substitution (heating only with electric heater and valve - cooling with valve) 4 DIP 3 = OFF DIP 4 = ON Electric heater integration (heating with electric heater and valve - cooling with valve) 5 Fan motor Thermostatic control Continuously running 6 Actuator type ON / OFF (thermal) Floating (3 points) 7 Heating / Cooling control Manual (local) Centralized 8 Function of auxiliary input Economy Window / remote on / off 12

13 Led function Cooling (Umbrella) - Thermostat demand: Led green on with fan running and valve opened Led green blinking (1 time every 2 seconds) with fan stopped and valve opened (fan it is in stand-by because the water temperature it is > 15ºC) - Thermostat in the set point reached: Led off (fan stopped and valve closed) Heating (Snowman) Air Filter - Thermostat demand: Led red on with fan running and valve opened Led red blinking (1 time every 2 seconds) with fan stopped and valve opened (fan it is in stand-by because the water temperature it is < 35ºC) - Thermostat in the set point reached: Led off (fan stopped and valve closed) - Fan on for electric heater post-cooling Led red blinking (2 time every 2 second) - Led yellow or orange = dirty filter (after 800 hours of fan operation) Reset dirty filter: make 5 transition fast (between one and one should not spend more than three seconds) between minimum (I) and medium (II) speeds 13

14 14 We reserve the right to add modifications without prior notice