CC650 Production / Industrial Hose Crimper

Transcription

1 The CC650 Series es hose crimper with the Patented ted ACT Controller olle ler and 350 tons of crimping force has the capability to crimp hoses from ¼" up to 6" in diameter. UNIQUE USER FRIENDLY PATENTED ACT TM CONTROLLER Fully adjustable crimp to diameter. Production capabilities. Pressure Compensation uses pressure to eliminate trial and error. Memory capacity for accurate repeatability. Automatically converts inch to mm and mm to inch so that no calculation is ever required. -¼" 86mm Max Head Opening W/O Dies: Can accommodate 6" 50 lbs SAE fl ange. CC650 CRIMPER OPERATORS MANUAL WITH ACT TM CONTROLLER Updated 0/6/07

2 SAFETY PRECAUTIONS! SAFETY PRECAUTIONS! READ INSTRUCTIONS AND IDENTIFY ALL COMPONENT PARTS BEFORE USING CRIMPER. CRIMPER CC650 CAN PRODUCE 350 TONS OF CRIMPING FORCE. KEEP BOTH HANDS AWAY FROM PINCH POINTS. CONSULT HOSE AND FITTING MANUFACTURER FOR CORRECT MACHINE SETTINGS AND CRIMP MEASUREMENTS. ALWAYS WEAR EYE PROTECTION.

3 TABLE OF CONTENT SAFETY PRECAUTIONS COMPONENT PARTS & TECHNICAL DATA INITIAL SET UP ADAPTER DIE INSTALLATION HYDRAULIC DIE INSTALLATION LUBRICATION PROCEDURE AccuCrimp ACT TM CONTROL PANEL AccuCrimp ACT TM CONTROL PANEL QUICK START AVAILABLE CC650MIC MANUAL DIAL MICROMETER PLC RESET PROCEDURE TROUBLESHOOTING CC650 CRIMPER REPLACEMENT ACCESSORIES COMPONENT PARTS BREAKDOWN CC650 DIE PART IDENTIFICATION CC650 PREVENTATIVE MAINTENANCE PACKAGE CUSTOMCRIMP NO-NONSENSE WARRANTY STATEMENT CUSTOMCRIMP CONTACT INFORMATION

4 COMPONENT PARTS & TECHNICAL DATA Manual Back Stop 7.5 HP motor high capacity pump Main Power Switch Reservoir 69" 9" 5" Adjustable Mirror Patented ACT TM Controller Industrial Die Storage Shelves Hydraulic 99mm Die Storage Pockets Foot Pedal for use in Semi and Full automatic mode Small Footprint for minimum use of space Technical Data CC650 / CC650MIC 350 Ton *6SP: 3" *Max Industrial: 6" L: 9" x W: 5" x H: 69" Weight:,000 lbs CC650 Power: 7.5HP/30V/3Phase (Standard) 7.5HP/0V-80V/3Phase (Optional) 5HP/30V/Phase (Optional) CC650 Adjustability: Inch / Metric CC650MIC Power: 5HP/30V/3Phase (Standard) 5HP/0V-80V/3Phase (Optional) 5HP/30V/Phase (Optional) CC650MIC Adjustability: Metric Die series 99S / 60S / 60OB Opening w/o dies: 86mm /.5" Master die inside diameter: 60mm / 6.9" Master die travel: 8mm / 5" Reservoir capacity: US Gallons Oil type: ISO 6 Hydraulic Oil Available Manual Dial Adjustment Micrometer *Crimper capacity is estimated based ontypical -piece fi tting. Actual results may vary depending on the hose and fi tting manufacturer. -¼" 86mm Max Head Opening W/O Dies: Can accommodate 6" 50 lbs SAE fl ange. Patented ACT Controller: Offers language settings to choose from English, Espanol, Deutsch and Francais. Easy Maintenance: Through the lubrication fi ttings. Features Of Operator Interface: User Friendly navigation, Manual Mode, Semi Auto Mode, Full Auto Mode and Production Features. Industrial Crimp Calculator: Takes guesswork out of industrial crimping. Manual Back Stop: Makes hydraulic hose production crimping fast and accurate.

5 INITIAL SET UP Check the oil level in the sight glass gauge on the front of the reservoir. U.S. gallons of ISO 6 hydraulic oil is required to completely refi ll the reservoir. Note: Oil can be drained from either of the two ports at the rear bottom of the reservoir. An additional oil cooler, while not normally required, can be plumbed into the two ports at the rear bottom of the reservoir. Check electrical circuit to be certain that it matches to the crimper requirements as shown on the voltage decal on the electrical enclosure. Electrical Requirements: 7.5HP/30V/3Phase (0 Amp) 7.5HP/0V-80V/3Phase (0 Amp) 5HP/30V/Phase (30 Amp) Plug the cord directly into the appropriate wall outlet. Caution: Do not run the crimper on an extension cord as low voltage can damage the motor and / or electrical components. Check to be certain that the motor rotates in the direction of the arrow shown on the motor housing. If motor rotation is incorrect reverse any two hot wires in the crimper plug. (Note: This is applicable to 3 phase circuits only) Note: Damage to the pump can result if the motor does not rotate in the correct direction. 5

6 ADAPTER DIE INSTALLATION ADAPTER DIE INSTALLATION: Note: 60 mm to 99 mm Adapter Dies are furnished with the crimper. Adapter dies are held in place by the die locking pins (as shown in photo #). The I.D. of the adapter dies must match the O.D. of the corresponding adapter die or hydraulic die or accurate crimps can not be made. Photo # Note: Tap the START button then CHANGE DIES button in the lower left corner of the screen; it will start to fl ash. This button allows you to jog the crimper head in and out during die installation using the green CLOSE and OPEN button below the screen on the front of the ACT Controller. Photo # Bring the master dies to the fully opened position (as shown in photo #). To have access to the (8) master die locking studs. Install the 60 mm to 99 mm Adapter Dies (as shown in photo #3). Photo #3 Note: The die size stamped on the face of the adapter dies should face toward the operator. Note: Use the T-Handle Wrench provided to loosen and tighten the master die locking studs to secure the adapter dies (as shown in photo #). Photo # 6

7 HYDRAULIC DIE INSTALLATION HYDRAULIC DIE INSTALLATION: With the 60 mm to 99 mm Adapter Dies installed, use the Quick Change Tool to install the hydraulic dies. The I.D. of the adapter dies must match the O.D. of the corresponding hydraulic die or accurate crimps can not be made. Note: Tap the START button then CHANGE DIES button in the lower left corner of the screen; it will start to fl ash. This button allows you to jog the crimper head in and out during die installation using the green CLOSE and OPEN button below the screen on the front of the ACT Controller. Photo # Photo # Bring the crimper head to fully opened position and install the Hydraulic Dies with the quick change tool (as shown in photo #). Note: The die size stamped on the face of the hydraulic dies should face toward the operator. Align the studs of the Hydraulic Dies with the holes in the Adapter Dies and with the crimper in manual mode SLOWLY close the crimper head on the hydraulic die set (as shown in photo #). Bring the crimper head to a fully closed position (as shown in photo #3). Photo #3 Remove the quick change tool as shown in photo #). Note: The Hydraulic Dies may also be inserted manually with the crimper head in the fully open position. Note: For Hydraulic Die removal, place the crimper in manual mode and bring the crimper head to a fully closed position. Insert the quick change tool and open the crimper head releasing the Hydraulic Dies form their spring retention holes. Photo # 7

8 LUBRICATION PROCEDURE Note: This specific style of grease gun fl ush fi tting adapter must be used to lubricate the CC650 crimper. Note: Use the mini grease gun w/ fl ush fi tting adapter and CrimpX grease (supplied with crimper) or a high quality moly-disulfi de grease. Failure to lubricate the crimper can cause premature failure, loss of accuracy and may result in costly repairs to the crimper. Lubricate the crimping head after each 00 crimping cycles or at the start of each shift if the crimper is used in a production setting. Note: Tap the START button then CHANGE DIES button in the lower left corner of the screen; it will start to fl ash. This button allows you to jog the crimper head in and out during die installation using the green CLOSE and OPEN button below the screen on the front of the ACT Controller. Photo # Bring the master dies to the fully closed position, and lubricate the master dies through the 8 lubrication fi ttings in the protective plates (as shown in photo #). With the dies still in the fully closed position, lubricate the () lubrication fi ttings visible through the two top lubrication fi ttings in the face of the crimper (as shown in the photo #). Photo # Bring the master dies to the fully open position, lubricate the crimper through the lubrication fi ttings visible through the two bottom lubrication fi ttings in the face of the crimper (as shown in the photo #3). Note: Parking the crimper in the full open position when not in use will prolong the life of the master die springs. Check the wear surfaces for grease. If the surfaces show any signs of wear, apply more grease. If you touch the wear surfaces, you should see a thin layer of grease on your fi nger. Photo #3 8

9 AccuCrimp ACT TM CONTROL PANEL 6" TOUCH SCREEN STYLUS PEN USB PORT NOTE: MANUAL MODE FUNCTION: OPEN DIES AUTO MODE FUNCTION: CYCLE STOP MANUAL MODE FUNCTION: CLOSE DIES AUTO MODE FUNCTION: CYCLE START EMERGENCY STOP IF THE CRIMPER IS IN MANUAL MODE, THE GREEN OPEN/CLOSE BUTTONS WILL OPEN AND CLOSE THE CRIMPER HEAD. IF THE CRIMPER IS IN AUTO MODE, THE BUTTONS FUNCTION AS CYCLE START AND CYCLE STOP BUTTONS. IF THE CRIMPER IS IN SEMI-AUTO MODE, PRESSING THE FOOT SWITCH OR THE CLOSE BUTTON WILL CLOSE THE CRIMPER HEAD AND RELEASING WILL HALT THE CLOSING ACTION. Products covered by all or some of these Patents: US 7,383,709; US 8,30,7; EP,909,987 and Patents Pending. 9

10 AccuCrimp ACT TM CONTROL PANEL QUICK START While the ACT TM crimper has the ability to perform a number of fully automatic functions, manual operation is also possible. To make a manual crimp, two numbers are needed: The closed diameter of the die (in either inches or mm). The finished crimp diameter (in either in or mm) That s all you need to know. ACT TM does the rest. TO MAKE A MANUAL CRIMP: Press START Button. Select CRIMP TO DIAMETER. Enter the closed diameter of the die set in either in or mm and press ENTER. Note: for a 5mm die, enter 500. ACT TM will add the decimal point. Decimal point entry: For.56 inch entry, enter 560 (Controller supplies 3 places for entries in inches). For a 50.0 mm entry, enter 5000 (Controller will supply decimal places for entries in mm). Enter the fi nished crimp diameter and press ENTER. From the ENTER CRIMP screen, press the MANUAL button to put the crimper in manual mode. Confi rm that the die and fi nished crimp diameters are correct and that MANUAL MODE is displayed. Press and hold the green CLOSE button until the crimper stops closing. Check the fi nal crimp diameter. If a minor correction is required see HOW TO MAKE MINOR CORRECTIONS. Tip: Pressing the CHANGE DIES button allows the crimper head to be fully opened or closed with the green OPEN-CLOSE buttons on the controller front panel When the CHANGE DIES button is blinking the dies can be opened and closed manually without altering any of the crimper settings. Note: When using the overbore (OB) dies you must use the SAVED DIE feature. Press the USE SAVED DIE to select the correct die set from the die memory table. 0

11 AccuCrimp ACT TM CONTROL PANEL QUICK START HOW TO MAKE MINOR CORRECTIONS Due to variations in hose and fi tting tolerances a minor crimp adjustment may be required if the measured diameter of the final crimp is not within the hose and fitting manufacturer s specifications. ACT TM technology makes minor corrections a simple process which requires no addition or subtraction. If the finished crimp diameter is not within the required specifications: Press the ADJUST CRIMP button. Enter the measured diameter of the fi tting in either inches or mm (Do not enter the amount of correction) and press ENTER. Press OK. Make another crimp and verify that the fi tting is within specifi cations. EXAMPLE: If the hose and fi tting manufacturer specifi es that the fi nished crimp should measure.500 to.50 and the measured crimp diameter was.530, simply enter the measured diameter (530 - Controller will supply 3 decimal places) and press SAVE. The fi nished crimp diameter can be entered in either in or mm and ACT TM will make the conversion. While a single correction will usually bring the hose and fi tting into specifi cations, the process can be repeated as many times as is required.

12 AccuCrimp ACT TM CONTROL PANEL QUICK START HOW TO ADD A SAVED DIE Up to 50 different dies can be saved in the computer memory. These dies can be recalled in the set up process eliminating the need to re-enter the die size each time. To enter a saved die: From the OPTION screen, press SETUP MODE. Select SAVED DIES. Select the save position (-50) where the die is to be saved and press the EDIT button. Enter a die description (up to alpha/numeric characters). Enter diameter units (inch or metric). Enter the closed diameter of the die. Press SAVE and EXIT. The saved die will now appear on the SELECTED DIE screen. From this screen individual dies can be cleared or edited. HOW TO RECALL A SAVED DIE Select CRIMP TO DIAMETER, and from the OPTION screen, select USE SAVED DIE. Select the saved die (-50) and press LOAD and then OK. The die parameters will now be used for the crimp process. From the ENTER CRIMP screen press MANUAL. The saved die will now be shown on the crimp parameters screen.

13 AccuCrimp ACT TM CONTROL PANEL QUICK START HOW TO ADD A SAVED CRIMP Adjust the die diameter and crimp diameter as required and place the crimper in MANUAL mode. Press SAVE. Select a location (-00) and press EDIT. Enter a description (up to characters). Press SAVE and EXIT. The die and crimp setting can now be recalled from the saved location as required. TO RECALL SAVED CRIMP Select USE SAVED CRIMP from the option screen. Select a previously saved crimp from location -00. Press LOAD. Press OK. The saved crimp will appear on the manual screen. 3

14 AccuCrimp ACT TM CONTROL PANEL QUICK START FULL AUTO MODE With the crimper in FULL AUTO mode additional functions are available: The crimper will cycle automatically from the CRIMP button on the touch screen, the green CYCLE START button on the panel, or the foot switch. To set the position to which the dies will retract, close the crimper to the desired retract position prior to pressing the FULL AUTO button. Note: The retraction position must be set a minimum amount above the fi nished crimp diameter or the crimper will not retract. The minimum retraction diameters are: CC38 - Crimp Diameter plus mm CC-50 - Crimp Diameter plus mm CC60 - Crimp Diameter plus 3 mm Pressing the FULL AUTO button will toggle the crimper into SEMI-AUTO mode. In SEMI-AUTO mode, pressing the FOOT SWITCH or the CLOSE button will close the crimper head and releasing it will cause the head to stop closing. This mode allows the crimper to be jogged into position allowing more precise positioning of a fi tting in the dies. Pressing the SEMI AUTO button will toggle the crimper back to FULL AUTO mode In FULL AUTO mode pressing the foot switch will start the crimp cycle and the dies will stop closing when the crimp cycle is complete. The COUNT function is activated allowing the operator to monitor the number of crimps made. A measurement can be required after a preset number of crimps. See SET REQUIRED MEASUREMENT SET REQUIRED MEASUREMENT Press the PRODUCTION button. Determine if or crimps will count as a crimp Toggle the CRIMP ADJUSTMENT REMINDER to ON. Set the COUNTS BETWEEN CRIMP MEASUREMENTS to the desired number and press OK. At the set interval, the ADJUST CRIMP screen will come up and the operator will be asked to measure the last crimp and enter a correction if required.

15 AccuCrimp ACT TM CONTROL PANEL QUICK START ADJUST CRIMP COUNT If a production operation is interrupted for some reason, it is possible to reset the counter to where the operation was at the point of interruption. Press the Adjust Count button from the auto crimp screen. Press the Crimp Counter and reset the count to the desired point. ACT TM ADDITIONAL FEATURES Additional features and functions of the ACT TM controller can be accessed by pressing the MORE button on the MACHINE SET UP screen. When Allow Crimp to Diameter is set to YES, all of the adjustment functions of the crimper are available. When Allow Crimp to Diameter is set to NO only the settings entered as a saved crimp can be used. English or Spanish language options are available. The Use Pressure Compensation is set to YES for all crimpers equipped with a pressure transducer. A security code is required to turn this function on or off. 5

16 AccuCrimp ACT TM CONTROL PANEL QUICK START ACT TM ADDITIONAL FEATURES Pre-Loaded Crimp Specifications In addition to the ability to store up to 50 user entered dies and 50 user entered crimp settings, the ACT Controller has the capability of accepting pre loaded manufacturer s crimp specifications. CustomCrimp does not maintain these specifications as they are proprietary to the individual hose and fitting manufacturer. If, however, your ACT Controller was pre loaded with a manufacturer s crimp specifications or if they are available to you, they are accessed in the following manner: Press the Crimp Memory Table Button. Press the access button to bring up the stored crimp specifi cations. Scroll through the crimp specifications to select the correct one. The right hand rocker button moves through the crimp specs one line at a time and the left hand rocker button moves one screen at a time. When the correct crimp specification is selected, press the highlighted selection and then the Load button and select OK to write the data to the ACT TM Controller. This will bring up the familiar crimp screen and the crimper can then be operated in the normal manner. 6

17 INDUSTRIAL CRIMP CALCULATOR The Industrial Hose Crimp Calculator is part of the ACT TM controller package on many Custom Crimp crimpers capable of crimping industrial hoses. With a few simple measurements, it takes the guess work out of industrial hose crimping and eliminates the need for charts and graphs. Note: Not all ACT TM controllers have the Industrial Crimp Calculator software. Contact your sales specialist for information on a specifi c crimper. Press the CRIMP TO DIAMETER button. Press the INDUSTRIAL CRIMP Button. Press MEASURE. If the hose diameter is known or a pi tape is being used, enter the hose O.D. If hose O.D. is not known, press MEASURE for wall thickness options. Measure the wall thickness of the hose. Press the right arrow and take more measurements of the hose wall thickness. The Industrial Crimp Calculator will average the three measurements. Enter the stem diameter of the fi tting. For example: If the stem diameter is inches, you would enter 000 and the ACT TM controller would supply the decimal place. Measure and enter the wall thickness of the ferrule. Next enter a compression factor. While this can vary depending upon the specifi c hose and manufacturer, the following guidelines are a starting point: Standard Industrial hose (approximately / inch wall thickness): % Standard lay fl at hose: % Note: Contact your hose and fi tting manufacturer for the compression factor to use on a specifi c hose and ferrule, Press PROCESS and enter the die diameter if you have not already done so. Select and install the correct die set for the combination of hose and fi tting being crimped. Press MANUAL and proceed to crimp the hose. 7

18 CC650 MIC MANUAL DIAL MICROMETER The CC650 MIC is available with a manual dial micrometer in place of the ACT TM controller. Set up and adapter and die installation are identical to the CC650 ACT model. The micrometer is a direct reading metric micrometer. With the micrometer set at zero, the die set will close to the fully closed diameter stamped on the face of the die. The number set on the micrometer will be the amount ABOVE the closed diameter of the die at which the dies will stop closing. Example: If the required fi nal crimp diameter for the hose and fi tting being crimped is 65.5 mm, the correct die set to use would be a 63 mm die set. The micrometer would be set at.5 mm as shown, and the fi nal crimp diameter would be 65.5 mm (63 mm-closed die diameter plus.5 mm) Opening and closing of the crimper head is controlled with the foot switch. Press and hold the foot switch until the crimp is complete and the dies stop closing. Always check the hose and fi tting with a caliper to be certain that the fi nal crimp diameter is in accordance with the hose and fi tting manufacturers specifi cations. 8

19 PLC RESET PROCEDURE PLC RESET PROCEDURE: The PLC (Programmable Logic Controller) requires a relatively constant source of electrical power. Power surges, outages or drops in power can cause the PLC to lose its settings. This may result in missing or misplaced information on the controller screen. RESETTING THE PLC TO ITS ORIGINAL SETTINGS IS A SIMPLE PROCEDURE: Open the front of the Control Panel. Power up the crimper from the main power switch. The crimper must be powered on during the PLC reset procedure. Move the three position toggle switch on top of the PLC right to the STOP position and then left to the RUN position. Return the toggle switch to the center TERM position. Repeat for the other PLC Unit. Cycle the main power off and back on. The PLC and the crimper should now operate normally. Close the control panel. 9

20 TROUBLESHOOTING PROBLEM: CRIMPER WILL NOT RUN AT ALL Check the E-Stop switch to be certain that it is not depressed. A slight twist is required to release switch after it has been depressed. PLC (Programmable Logic Control) must be reset. See instructions on the previous page. PROBLEM: CRIMPER RUNS BUT IS SLOW OR NON-FUNCTIONAL Check supply voltage to see that it matches the voltage specifi ed on the tag attached to the crimper. Many performance problems are the result of low voltage or inadequate electrical service. Check motor rotation and be certain that the motor rotates in the direction of the arrow on the motor housing. For three phase units rotation can be reversed by switching any two wires in the plug. PROBLEM: CRIMPER WILL CLOSE ON FITTING BUT DOES NOT DEVELOP POWER TO COMPLETE THE CRIMP Check oil level. Position dies to the fully open position and check oil sight gage in rear of machine. Be sure the oil level is in the middle of the sight glass. Use ISO 3 or 6 weight hydraulic oil. PROBLEM: CRIMPER WILL NOT OPEN TO RETRACT POSITION IN AUTO MODE Retract position must be at least 3 mm larger than the fi nal crimp diameter. If problem (s) persist contact Customer Service for additional troubleshooting assistance. 0

21 CC650 REPLACEMENT ACCESSORIES 6" Touch Screen Panel P/N:0600-ACT CC-Foot Switch P/N:CC-FOOTSWITCH 99mm Quick Change Tool P/N:057 CC-Mirror P/N:037 Manual Back Stop P/N:MBS-60 Electronic Back Stop P/N:EBS-60 Industrial Die Shelf P/N:0357 Industrial Hose O.D Tape (Pi Tape) P/N:0390 Mini Grease Gun w/ CRIMPX Die Lubricant 3 oz mini grease tube P/N:03889 CRIMPX Die Lubricant 3 oz mini grease tube P/N:03887 CRIMPX Die Lubricant oz large grease tube P/N:03888 CustomCrimp Notched Digital Caliper IN/MM P/N:CC-Caliper Adapter Die Set 60mm OD to 99mm ID P/N:03899 Die Lock Pin For 8S/99S Die Series P/N:058 Die Lock Pin For 30S/5S Die Series P/N:003

22 COMPONENT PARTS BREAKDOWN CC 650 Frame and Sliding V Block (0398) ITEM PART NUMBER DESCRIPTION 0333 CC600 Frame 033 CC600 Sliding V Block QTY

23 COMPONENT PARTS BREAKDOWN CC 650 Feet and Leg Assembly (0397) ITEM PART NUMBER DESCRIPTION 0333 CC600 Frame CC600 Left Foot CC600 Right Foot R CC600 Right Leg Assembly L CC600 Left Leg Assembly 6 MTS56 M X 35 SHCS 7 WS3558 / Flat Washer QTY 6 6 3

24 COMPONENT PARTS BREAKDOWN 3 3 CC650 Cylinder Installation Assembly (0399) ITEM PART NUMBER DESCRIPTION QTY 0393 CC 650 Cylinder Assembly Cylinder Mounting Bracket 3 MTS565 M X 50 SHCS 8 WS3558 / Flat Washer

25 COMPONENT PARTS BREAKDOWN CC 650 Wear Plate Assembly (03950) ITEM PART NUMBER DESCRIPTION QTY 0393 CC650 Cylinder Assembly 033 Sliding V-Block V-Block Locating Pin Fixed Wear Plate Side Guide Plate CC650 Master Die Wear Plate Plate Mounting Bracket Wear Plate T-Nut 8 9 MTS599 M X SHCS 0 99A0 M5 X FHCS 8 MTS5583 M0 X 30 SHCS 68 5

26 COMPONENT PARTS BREAKDOWN CC 650 Protective Plate Assembly (0395) ITEM PART NUMBER DESCRIPTION QTY 039 Bracket 99A0 M5 X FHCS Cover Plate 8 99A0 M6 X 0 FHCS Protective Plate Key 6 99A M5 X 6 FHCS CC650 Protective Plate Alignment Tab 9 MTS555 M8 X 30 SHCS Backstop Mount 99A8 M8 X 0 FHCS 6

27 COMPONENT PARTS BREAKDOWN CC600/650 Potentiometer/Limit Switch Assembly (0395) ITEM PART NUMBER DESCRIPTION QTY 0373 Roller Limit Switch 0339 Limit Switch Adjustable Bracket 3 SKC X 3/ SHCS 0338 Potentiometer Bracket 5 990A58 M0 X 00 SHCS CC600/000 Linear Potentiometer M X 0 SHCS 8 MTS565 M X 50 SHCS A8 M X 70 Set Screw 7

28 COMPONENT PARTS BREAKDOWN CC600 Sheetmetal Assembly (03756) ITEM PART NUMBER DESCRIPTION 0335 Front Sheetmetal Panel 0335 Back Sheetmetal Panel 3 MTS555 M8 X BHCS Top Sheetmetal Wrap Front Die Sheetmetal Cover 6 939A3 M6 X 6 BHCS 7 990A330 M6 X 5 BHCS R Rear Die Sheetmetal Cover Access Panel MM Die Holder SKB079 /-0 X / SHCS 0357 Industrial Die Compartment QTY

29 COMPONENT PARTS BREAKDOWN 3 CC600 Neoprene Pad Installation (03768) ITEM PART NUMBER DESCRIPTION Front Neoprene Pad Cubbie Neoprene Pad Back Neoprene Pad Industrial Die Holder Mat QTY 6 5 9

30 COMPONENT PARTS BREAKDOWN CC650 Master Die Assembly (0395) Current as of // ITEM PART NUMBER DESCRIPTION 08 CC650 Master Die Carrier CC650 Master Die Shoes R CC650 Master Die Shoes Medium T-Nut Short T-Nut 6 990A8 M X SHCS Master Die Spring mm Flush Style Grease Fitting QTY

31 COMPONENT PARTS BREAKDOWN CC600 Electrical Enclosure Assembly (03759) ITEM PART NUMBER DESCRIPTION Electrical Enclosure Electrical Enclosure Circuit Panel /30 30V Power Supply V Power Supply VAC-5HP/7.5HP Overload Relay VAC Overload Relay A 30VAC-5HP/7.5HP Motor Contactor Amp Disconnect Switch Amp Disconnect Switch " Din Rail Ground Terminal Block Fuse Block Level Terminal Block Relay Block 0368 White Relay Block (Motor) 0378 Black Relay Block Midget 5 AMP Fuse Holder (30V) Midget 5 AMP Fuse Holder (80V) Midget 5 AMP Fuse " Plastic Wire Duct /" NPT Cord Grip /" NPT Romex Cord Grip Pole Female Receptacle w/pigtails QTY

32 COMPONENT PARTS BREAKDOWN CC600/000/Nut Crimper Tower Box Assembly (0376) ITEM PART NUMBER DESCRIPTION 0380 CC600/000/Nut Crimper Tower Box 0376 Tower Box Electrical Panel " Din Rail 0370-PLC DL05 PLC ACT 0-0V Analog In/Out Card " Plastic Wire Duct Ground Terminal Block Level Terminal Block Terminal Block GREEN Open/Close Push Button 055-RED Emergency Stop Button 0600-ACT 6" Touch Screen Text Panel USB Connector 0387 Foot Pedal Receptical /" NPT Cord Grip /" NPT Romex Cord Grip /8" NPT Cord Grip QTY 3 9 3

33 COMPONENT PARTS BREAKDOWN CC600 Power Unit Assembly (03758) ITEM PART NUMBER DESCRIPTION QTY 0378 Gallon Tank 053 CC000/600 Manifold Block Assembly CC000/600 Motor and Pump Assembly Reservoir Top Plate 5 SKF3 5/6-8 x 3/ FHCS 6 990A66 M8 x 90 SHCS 7 NC56-Z /-3 x / HHS 8 WLK3508-Z / Lock Washer Venter Filler Cap Electrical Sub Assembly Sight Filler Glass Flange Gasket

34 CC650 DIE PART IDENTIFICATION 60mm to 99 mm Adapter Dies Master Dies 99mm Hydraulic Dies Master Dies Accept: 60/99mm Adapter Dies; or 60S Series Dies (8-35mm) 60OB Series Dies ( - 90mm) 60/99 Adapter Dies Accept: 99S Series Dies (8.5-78mm (¼" - ½")) Master Die 60mm to 99mm Adapter Die 99mm Hydraulic Die 3

35 CC650 Preventative Maintenance Package CustomCrimp s preventative maintenance program is an annual service which keeps your crimper cleaned, calibrated, and running in peak performance. This service includes the cleaning of main wear components, inspection of wear components and seals, and calibration of your crimper. Prevent downtime with this economical service package performed at your facility. CC600 / CC650 PREVENTATIVE MAINTENANCE PACKAGE INCLUDES: Inspection and Cleaning of the Protective Plates. Inspection and Cleaning of the Master Die Cover Plates. Inspection and Cleaning of the Master Die Carriers. Inspection and Cleaning of the Master Die Shoes. Inspection and Cleaning of the Master Die Wear Plates. Inspection and Cleaning of the Master Die Alignment Keys. Inspection and Cleaning of the Side Guide Plates. Inspection and Cleaning of Adapter Dies. Inspection of the Cylinder. Inspection of the Potentiometer. Inspection of the Electrical Components. Replacement of the Master Die Springs. Crimper Care Package (Dies Studs, Quick Change Tool Pins, Grease Gun, Screen Protector). Oil Change (If Customer Provides the Oil and disposal of used oil). Update of ACT Controller software (if needed). New Grease Applied of All Wear Surfaces. Crimper Calibration. Written Crimper Documentation Report. 35

36 CC650 Preventative Maintenance Package We understand how critical it is to have your crimpers running everyday and limiting downtime. We hope that our services will help eliminate downtime, shipping costs, and uncertainty of when your machine will be fi xed. Please feel free to search our website and contact us with any questions. DURABLE, RELIABLE DESIGN = PROFITABILITY Annual service prevents crimper downtime. Save money on multiple crimpers at one location. Written report showing crimpers current condition and future needs. Inspection & Cleaning of the Protective Plates Inspection & Cleaning of the Master Die Cover Plates Inspection & Cleaning of the Master Die Carriers & Master Die Shoes Inspection & Cleaning of the Master Die Wear Plates & Master Die Alignment Keys Inspection & Cleaning of Side Guide Plates Inspection & Cleaning of Adapter Dies Inspection of Cylinder Inspection of Potentiometer Replacement of Master Die Springs Inspection of Die Studs & Quick Change Tool Pins Master die assembly wear and function: EXCELLENT Master die wear plates wear and function: EXCELLENT Side guide plates wear and function: EXCELLENT Cylinder condition: EXCELLENT Protective plates wear and function: EXCELLENT Master die alignment keys wear: EXCELLENT VENTATIVE MAINTENANCE: CC 650 MASTER DIE SPRIN CRIMPX GREASE GUN W OIL 65 5 GALLON OIL KIT 699 CC SERIES SUCTION CC SERIES SCRE Replacement of Die Studs & Quick Change Tool Pins Update of ACT Controller Software (If needed) New Grease Applied on All Wear Surfaces Crimper Calibration HYDRAUL Written Crimper Documentation Report CustomCrimp See the complete line of CustomCrimp Crimpers and Accessories at: (9)

37 CUSTOMCRIMP NO-NONSENSE WARRANTY STATEMENT CustomCrimp No-Nonsense Warranty Statement All CustomCrimp Products are warranted to be free of defects in workmanship and materials for one year from the date of installation. This warranty ends when the product becomes unusable for reasons other than defects in workmanship or material. Any CustomCrimp Product proven to be defective in workmanship or material will be repaired or replaced at no charge. To obtain benefi ts of this warranty, fi rst, contact Warranty Repair Department at Custom Machining Services at (9) 6-68 and then deliver via prepaid transportation the complete hydraulic product to: ATTN: WARRANTY REPAIR DEPT. Custom Machining Services, Inc. 38 North Co. Rd 00 East Valparaiso IN 6383 If any product or part manufactured by CustomCrimp is found to be defective by CustomCrimp, at its option, CustomCrimp will either repair or replace the defective part or product and return via ground transportation, freight prepaid. CustomCrimp will not cover any incoming or outgoing freight charges for machines sold outside The United States. This warranty does not cover any product or part which is worn out, abused, altered, used for a purpose other than for which it was intended, or used in a manner which was inconsistent with any instructions regarding its use. Electric motors are separately warranted by their manufacturer under the conditions stated in their separate warranty. 37

38 CONTACT US CUSTOMCRIMP, YOUR SINGLE SOURCE FOR HOSE ASSEMBLY PRODUCTS. Products and services to support industry wide hose assembly needs. CustomCrimp Custom Machining Services, Inc. 36 N. County Rd. 00 East Valparaiso, IN 6383 Ph: (9) 6-68 Fax: (9) CustomCrimp See the complete line of CustomCrimp Crimpers and Accessories at: (9)