1. Introduction 2. Description. System functions 2.1. Controls and indication 2.2. Switch ON/OFF 2.3. Connecting to a Wi-Fi network 2.4. Test mode 3.

Transcription

1 Mobile Comfort System Thermostat under smartphone control Wi-Fi Control your comfort from anywhere in the world! 1

2 1. Introduction 2. Description. System functions 2.1. Controls and indication 2.2. Switch ON/OFF 2.3. Connecting to a Wi-Fi network 2.4. Test mode 3. Control and operation 3.1. System configuration settings 3.2. Local network List of thermostats Operation modes 4. Thermostat settings 4.1. Room name 4.2. Heating schedule 4.3. «Vacation» mode 4.4. Access through internet 4.5. Wi-Fi connection 4.6. Information about device 5. System self-diagnostic 5.1. Floor temperature sensor breakout 5.2. Date and time setup and adjustment 5.3. Operations at Wi-Fi signal loss 5.4. Network settings reset 2

3 6. Remote access 7. Installation guide 7.1. Floor temperature sensor installation 7.2. Thermostat mounting 7.3. Thermostat installation 8. Technical specification 9. Warranty 10. Service centers 3

4 INTRODUCTION 1 Group of Companies «Special systems and technologies» is the largest European manufacturer and distributor of electric heating systems and technologies for comfortable life, represents the Application MCS 300 for remote control of electric heating systems by means of the smartphone. This is a convenient solution for modern people, who value comfort and know how to be master of their time. Application MCS 300 allows a user to control the operation of electric warm floor system, connected to the special thermostat Mobile Comfort System. The thermostat and smartphone are commutated in the unified local network through common domestic Wi-Fi router. Control over all thermostats is possible through Internet from anywhere in the world. To do so, you need to preset your router. 4

5 Application MCS 300 allows to control the parameters and to manage the operation of electric heating systems in rooms (livingroom, bedroom, kitchen, children room, etc) or in several residential properties (apartment, house, country house). Simultaneously, the Application can interwork with 32 heating systems by connecting them in one Wi-Fi network. Maximum amount of united in one system thermostats depends on the type of the router and the amount of other devices, connected to the network. It is designated by the amount of free for use IP-addresses. In every room the application MCS 300 enables a user in current time mode to preset and maintain the heating temperature in the range from +5 С to +45 С, and also control the working order of heating system elements. 5

6 In basic settings of MCS 300 three operation modes are provided: Temperature maintenance mode with adjustment of temperature from +5 С to +45 С; «Vacation» mode. Activating this mode, a user presets the maintained temperature in the room in the range from +5 С to +12 С; Also, programmed mode of operation, which allows to preset the heating schedule for each room for the week ahead. A user enters desired heating temperature values for hourly amount of time for a day. You just preset the desired temperature. Thermostat MCS 300 monitors it itself, maintaining comfort and saving energy. Недельные установки повторяются постоянно в течении неограниченного времени. 6

7 DESCRIPTION. SYSTEM FUNCTIONS 2 Install the thermostat in the wall and connect it with the heating element of the warm floor system, as it shown in the installation guide, attached to the thermostat. Remote control and managing the heating through Internet. 7

8 Download free application for your smartphone Android in Google Play. Your smartphone with application MCS 300 Wi-Fi Wi-Fi router For remote access through Internet Thermostats MCS With built-in Wi-Fi-module Control all warm floor systems, connected together, from one mobile device. 8

9 CONTROLS AND INDICATION 2.1 The front cover does not have any LED signals and buttons (see fig. 1). If the cover is open, as it shown on fig. 6, there are LED signals and buttons under it (see fig. 2). Fig.1. External view of thermostat MCS «green» indication of power supply and Wi-Fi connection; 2. «red» indication of turned on heating mode and sensor failure; 3. «default» thermostat switch ON/OFF, control of the modes of the network connection; 4. «WPS» setup of WPS connection. 9

10 Fig. 2. Thermostat MCS 300 with removed front cover. Indication table of LED signals of thermostat MCS 300. Thermostat is OFF Heating is ON/ network error Sensor error Network connection. Network Failed Network ОК 10

11 THERMOSTAT SWITCH ON/OFF 2.2 Thermostat switch ON/OFF is carried out by pressing «default» key and holding it for at least 3 seconds. After switching on, the thermostat restores all settings, made before switching off. 11

12 CONNECTING TO A WI-FI NETWORK 2.3 To begin the operation you need to connect the thermostat to Wi-Fi network. At connecting the green LED signal blinks fast. Then, whether green or red LED signal lights up depending on the results of connecting (green connection ОК, red connection error). After that the thermostat switches to the standby mode. Wi-Fi network parameters Network name SSID: Wi-Fi network password: Wireless network mode: Channel width: Channel: Authentication method: Encryption WPA: any (for operation with the network on default: MCS_default) any (for operation with the network on default ) AUTO 40 MHz AUTO WPA-AUTO-Personal (WPA/WPA2 Personal)* AES * Thermostat supports the authentication method as WPA Personal 12

13 Connecting Wi-Fi network is possible in one of three ways: Connecting through WPS Press WPS key on your Wi-Fi router and hold it for at least 3 seconds. Press WPS key on your thermostat and hold it for at least 3 seconds. 13

14 The green LED signal will start blinking at that. Connecting process may take up to 1 minute. When the thermostat is connected to Wi-Fi network, the green LED light will stop blinking and go on continuously. If connection did not happen, the red LED signal will go on for 3 seconds, then it will go off, and the thermostat will switch to original condition, when none of the LED signals is on. Likewise, you may connect all required thermostats to Wi-Fi network. 14

15 Connecting through АР (access point) Quickly press twice «default» key on the thermostat. The green LED signal will start blinking at that. The thermostat becomes an access point at that moment, with the name «МАС-address of the device» (for example 00:08:DC:1А:24:26). At the process complete, the green LED signal will stop blinking and go on continuously. As a result you will have a new Wi-Fi network with the name «MAC-address of device» and password By connecting your smartphone to this network, you will get full access to the thermostat. 15

16 Please, take into account, that in this case you will have access only to one thermostat at a time. To control other thermostats in your house in the same manner, you would have to connect to another Wi-Fi network. This mode is usually used when it is necessary to manually connect the thermostat to your domestic Wi-Fi network or to setup the thermostat for operation in the network, access to which is absent at the moment. Connection to preset Wi-Fi network Quickly press 3 times the «default» key of the thermostat. The green LED signal will start blinking at that. The thermostat is now connecting to the network under the name «MCS_default» and password « ». If you have a router with matching network settings, the green light will stop blinking and go on continuously. The thermostat will be connected to specified network. In case the «MCS_default» network is absent, the red LED signal will go on, after that the thermostat will switch off (none of the LED signals is on, the heating is off, no connection to Wi-Fi network). 16

17 TEST MODE 2.4 MCS 300 may operate without Wi-Fi network and smartphone. Test mode is necessary for testing the thermostat at the installation of the heating system, at the stage of decoration works, when final settings are not carried out yet. In this mode a user cannot control the temperature of the warm floor system. The thermostat constantly maintains temperature at 28 С (factory settings do not change). Test mode can be activated only when switching on the thermostat for the first time. If the thermostat was connected someway to Wi-Fi network the test mode becomes unavailable. For its further usage it is necessary to return to the factory settings of the device. 17

18 To turn on test mode of the thermostat after power supplied to the device, press «default» key and hold it for 3 seconds. At that the green LED signal will blink in mode of 2 seconds on, 1 second off. To turn off the test mode, it is necessary to press «default» key and hold it for 3 seconds. It is possible to switch to any modes of connecting to Wi-Fi network from the test mode. 18

19 CONTROL AND OPERATION 3 SYSTEM CONFIGURATION SETTINGS 3.1 Connected by you thermostats, Wi-Fi router and your smartphone make a local network. To access it, setup Wi-Fi connection according to user manual of your smartphone. Install an application MCS 300 on your smartphone. 19

20 By pressing or moving the screen to the right you will get to the tabs menu of the application. Local network The List of thermostats, connected to Wi-Fi network, access to which is setup at that moment. 20

21 Demo mode Emulation work with thermostats. It is useful for studying the functions of «warm floor» system and MCS

22 LOCAL NETWORK 3.2 LIST OF THERMOSTATS After initialization of the application, choose the tab «local network»: If your smartphone is correctly connected to Wi-Fi network, you will see the list of thermostats, included in this local network. list of thermoregulators tabs update name of thermoregulator condition of thermoregulator 22

23 OPERATION MODE Selecting one-by-one each thermostat from the list, you will get to the section of the detailed control where you can setup thermostat in desired operational mode and maintained temperature. To do so, press the operation mode icon. When all modes are disabled, the thermostat is switched off. Settings Preset maintenance temperature Current temperature Programmed mode «Vacation» mode Temperature Maintenance 23

24 There are three operation modes in the thermostat: Programmed mode; Temperature maintenance; «Vacation» mode. Temperature Maintenance To setup desired maintained temperature, just point at it by moving the slider bar on temperature circle. 24

25 «Vacation» mode This mode is necessary when the temperature maintenance is not required, but undercooling of the room is not permissible. The mode is completely similar to temperature maintenance mode, but the temperature is adjustable in the range from +5 С to +12 С. It is setup in Settings, so the temperature value will not get changed by accident. 25

26 Programmed mode Programmed mode allows to perform flexible control over the temperature of the warm floor system with the purpose of the most comfort and energy saving. You may setup the temperature value for each time period for increments of one hour for each day of week. Forming heating schedule is carried out in Settings. 26

27 THERMOSTAT SETTINGS 4 By pressing the icon in the window of detailed control of thermostat, you will get to the Settings. Press icon «back» to return from all tabs to the thermostat settings. 27

28 ROOM 4.1 Enter the name of the room, desired by you. It corresponds to MAC-address of the thermostat on default. HEATING SCHEDULE 4.2 Choose a day of week. 28

29 By moving the sliders bars set up the required temperature for each hour. After setup all time slots, you may copy the settings to other days of week. To do so, press «copy» icon. Also, there is an option to copy the settings of any day to the current day. 29

30 «VACATION» MODE 4.3 Set up the temperature for «vacation» mode. ACCESS THROUGH INTERNET 4.4 To setup the remote control through Internet, it is necessary to enter external IP-address of your domestic router and port, to which MCS 300 is connected. The way to setup your router is described in section remote control. 30

31 WI-FI CONNECTION 4.5 If for some reasons the WPS connection to your domestic Wi-Fi network failed, you may connect the thermostat to it manually. To do so, switch the thermostat to access point mode, by pressing the «default» key twice, after that separately enter the name of the network and password. If there is no password, leave the box «password» blank. Press «connect». The thermostat will independently connect to indicated Wi-Fi network. 31

32 INFORMATION ABOUT DEVICE 4.6 Раздел содержит сведения о терморегуляторе. 32

33 SYSTEM SELF-DIAGNOSTIC 5 MCS 300 constantly controls the conditions of heating system, and also access to Wi-Fi network for each specific thermostat. FLOOR TEMPERATURE SENSOR BREAKOUT 5.1 In case of breakout or short circuit of the temperature sensor, the thermostat blinks with the red LED signal. The heating is switched off. On the screen of smartphone the corresponding message appears. 33

34 DATE AND TIME SETUP AND ADJUSTMENT 5.2 Application MCS 300 regularly checks accuracy movement of the thermostat clock. If inner clock of the thermostat and your smartphone clock differ by less than 15 minutes, the application will automatically adjust the thermostat clock. If time differs by more than 15 minutes, the corresponding request will appear and you will be able to make a decision on the necessary adjustment. 34

35 OPERATIONS AT WI-FI SIGNAL LOSS 5.3 In case of the Wi-Fi signal loss, the application will inform you. In the list of thermostats, the device, which lost the connection, will be tagged with exclamation mark. NETWORK SETTINGS RESET 5.4 To return to the factory settings, it is necessary to press the «default» key five times. At that, the thermostat will lose all preset networks and there will be an opportunity to turn on «test mode» again. 35

36 REMOTE ACCESS 6 Router settings for the remote control of thermostats of local network through Internet 1. Settings with static IP-address 6.1 Static IP-addresses are given by the providers. Providers may charge additionally for the IP-address. With the static IP-address it is required to redirect ports external IP-address to inner IP-address of the local network. Let s look at the settings as an example of router ASUS RT-N12. 36

37 Step 1. It is necessary to specify the IP- and MAC-addresses of the thermostats. You may find them in «System log», tab «DHCP lease». To specify МАС-address of the thermostat you may collate the address on thermostat sticker with the address at the tab «DHCP lease». 37

38 Step 2. For secure connection of the thermostats to the same local network addresses it is necessary to assign them with the static local addresses. You may do that at «LAN», tab «DHCP server». 38

39 Assign the thermostat with static IP-address. 39

40 Press «add» and then «apply» keys. 40

41 Step 3. Let s start redirecting ports. These settings can be adjusted at tab «Virtual Server» of screen «WAN». 41

42 Enter the service name (MCS 300_1), port for access of thermostat (5000), thermostat IP-address in local ( ) network, thermostat port for local network (it is the same for all thermostats 6350) And indicate the protocol (BOTH). Then press «add» key. Do the same procedure for the second thermostat. Enter the service name (MCS 300_2), port for access of the thermostat (5001), the thermostat IP-address in local ( ) network, thermostat port in local network (it is the same for all thermostats 6350) and indicate protocol (BOTH). Then press «add» key. After assigning all thermostats press «apply» key. 42

43 2. Settings with dynamic IP-address 6.2 The settings are similar to ones, described in section 1. The only difference is necessity to setup DDNS server. You may do that in tab DDNS of screen WAN strictly following the manual. Many of the router manufacturers offer this service for free. But it may be also paid for. 43

44 INSTALLATION GUIDE 7 INSTALLATION OF THE FLOOR SENSOR 7.1 Mounting the floor temperature sensor is carried out at the stage of the heating element installation. The floor temperature sensor should be put inside the corrugated tube (see fig. 3), the end of the tube should be closed with sealing blank cover in the order to prevent from concrete mixture or the adhesive glue penetration at the warm floor system installation. The corrugated tube with the sensor inside should be placed at the same level as heating cable, between the loops at the equal distances from them. The other end of the corrugated tube with the sensor installation wire inside should be laid in the prepared groove (chase) in the floor and approached to the installation place of the thermostat or the junction box. Unused excess of the tube and connection wire should be cut as applicable. 44

45 IMPORTANT! De-energize the wiring system before you connect the thermostat or disconnect it to check or replace. A qualified electrician is to perform the electric connections and power networking. The warranty does not cover any thermostat defects caused by inadequate installation. Please read carefully this manual before start operation cm Thermostat and heating cable section installation 45

46 Tooling and materials necessary for installation: 1. Corrugated plastic tube with the diameter not less than 16 mm (length of the tube depends on the place where the thermostat will be installed); 2. Standard plastic junction box; 3. Flat blade and crosshead screwdrivers; 4. Phase indicator to locate voltage wire. THERMOSTAT MOUNTING 7.2 Preparation of electrical connections. 1. Install junction box or terminal box. Approach the power line cables, installation wires of the heating mat or section and floor temperature sensor installation wire to the junction box. Apply voltage to the power line cable, determine phase and neutral cores by phase indicator and mark them accordingly. 2. Disconnect supply voltage. Please, carry out all connecting procedures only under disconnected power supply. Connect all wires to the device by screw terminals. 46

47 3. If you have two-conductor supply network (without earthing conductor), connection diagram is presented on fig. 4. The cold lead screen wire of the heating section is connected to neutral (N) conductor of the power network, to terminal 5. If you have three-conductor supply network (with separate earthing conductor), the connection diagram is presented on fig. 5. The cold lead screen wire of the heating section is connected to the earthing conductor of the power network via external screw terminal (included in the delivery set). temperature sensor N L 220VAC temperature sensor N L 220VAC Single-core heating cable Double-core heating cable Fig. 4. Connection diagram of the heating section and mats to two-conductor power network 47

48 network earthing conductor network earthing conductor temperature sensor N L 220VAC external screw terminal temperature sensor N L 220VAC external screw terminal Single-core heating cable Double-core heating cable Fig. 5. Connection diagram of heating sections and mats to three-conductor power network THERMOSTAT INSTALLATION 7.3 To install the thermostat it needs to be disassembled. Remove the front cover of the device. To do so, unlock the cover by insertion of the flat blade screwdriver in locking grooves located on both sides of the front cover (fig. 6). Remove the cover (fig. 7). Locking grove Locking grove Locking grove Fig. 6. Front cover removing 48

49 Fig. 7. Thermostat without cover Remove the cover. Mount the device into the junction box and fix it with at least two screws located along its horizontal axis (fig. 8). Assembly of the thermostat is carried in reverse order. Carefully install the front cover of the thermostat back to the place pressing by hand till both clamps click. Make sure that the front cover is securely fixed. 49

50 Front cover Fixing clamp Junction box Fixing clamp Fig. 8. Assembly/disassembly diagram of thermostat Thermostat MCS 300 has a removable frame. If it is necessary you may remove it and install the thermostat into the junction box without the frame. You may also use standard stopper plugs of some manufacturers of electric equipment. They may be installed instead of frame MCS 300 and attracted to the terminal box with the screws. 50

51 Clamps Clamps Frame Fig. 9. Disassembly of removable frame To remove the frame of the device press four fixing clamps, located on upper and bottom sides of the thermostat, with the flat blade screwdriver (fig. 9), pulling the frame out at that. Аккуратно установите лицевую крышку и нажмите на нее, до срабатывания обеих защелок. Убедитесь, что лицевая крышка прочно зафиксирована. 51

52 TECHNICALSPECIFICATIONS 8 THERMOSTAT MCS 300 Supply voltage 220 V Maximum load current 16 А Power consumption 2 W Weight 100 g Dimensions mm Store settings term at disconnected power supply 12 months IP rating IP21 Protection class II Floor temperature sensor TST02 Sensor installation wire length 2 m Operational temperature +5 С C Permissible relative air humidity 80 % Maintained temperature range +5 С C Module factory preset temperature +28 C 52

53 WARRANTY 9 Manufacturer guarantees compliance of the Thermostat quality to the requirements of Technical Specification TU assuming that the rules and installation and operation instructions are followed. Warranty period is 2 years from the date of sale. Within the warranty period the Buyer has the right to get the product repaired or replaced if defects are detected occurring through the manufacturer s fault provided instructions on installation and operation are followed. The warranty does not cover any mechanical damages of thermostats or defects caused by inadequate installation, connection or operation of the product. 53

54 To get the warranty obligation fulfilled, it is obligatory to submit filled out warranty certificate indicating name of the product, name of the place, where the product was bought, name of the Seller, bearing the Seller s stamp, authorized person signature and the Seller s signature. Claims Upon emergence of the faults within the warranty period of operation the customer should immediately submit a claim to the service center of the Manufacturer or his authorized regional representatives. 54

55 SERVICE CENTERS 10 DK «Metrostroya», 3, Kostomarovskij pereulok, build.1, Moscow, , Russia, tel.: (495) , , Proektiruemij proezd, build.7, Mytishchi, Moscow area, , Russia tel./fax: ,

56 Manufacturer: «Special Systems and Technologies» LLC 5274, Proektiruemij proezd, build.7, Mytishchi, Moscow area, , Russia Tel.: +7(495) , sst-iwarm.com 56