HVA -100 Pad Printer Machine Operation Manual

Transcription

1 HVA -100 Pad Printer Machine Operation Manual Serial No.: INTERNATIONAL

2 Content Section Page Introduction 1 Installation 2.1 Machine Setup: Ink Cup Installation 3.1 Ink Cup Removal 3.3 Printing Pad Setup 3.4 Pad Clean Tape Setup 3.5 Pad Clean Tape Platform Remove 3.6 Pad In/out Cushion 3.7 Adjustment of Pad Stop Position for Pad Clean 3.7 Worktable Adjustment 3.8 Effective Printing Area with Pad Clean Attachment 3.9 Control Feature: Front Control Panel 4.1 Pneumatic Control Panel 4.2 Control Sequence 5.1 Programm List 6.1 Sensor Layout 7 Electrical Circuit Diagram 8.1 Pneumatic Circuit 9 Maintenance 10.1 Spare Parts List 11

3 INTRODUCTION The following manual will familiarize you with the setup, use and maintenance of your printer. Please note that the diagrams shown within this manual are not to scale, and may not show all details. We would like to draw your special attention to the following notes: WARNING It is the operator s responsibility to comply with the following safety instructions to prevent any personal injury. 1. Please disconnect the main power supply before attempting any machine maintenance. Foot-switch is to stop machine for adjustment only. 2. The air pressure must be released before attending to any service inside the machine or any moving accessories. We have used the followings signs to show special dangerous situations: Warning! Electrical Warning! Warning - Danger of Fire! Warning - Danger of hands being crushed while working on pneumatic elements! Warning - Do not smoke while working on the machine! 1

4 Installation Mechanical Part: Machine Standing Horizontal Adjustment: Place machine on flat place. If not, you need to adjust machine foot levers to adjust machine level. Adjusting steps is shown below: Steps: 1.Place level ruler on ink cup platform of machine to survey machine horizontal. 2.Release upper screw nut of foot lever. 3.Turning foot lever supporter up or down to adjust supporting level. 4.Tighten upper screw nut to fix supporter position. (Test Result: Adjust horizontal level until the level ruler on platform indicating desirable outcome.) 885mm 148mm 1400mm 75mm 744mm Ground Upper Screw Nut Supporter Foot Lever 2.1

5 Installation Electrical Part: Power cable Fuse Foot switch connector Power On / Off Switch Printer Rear Control Panel (at the rear of machine body) - Connect foot switch to foot switch connector. - Plug in the main power cable with correct power plug to main power connector. Machine is suitable for AC 110V or 220V power supply. Read label at the back. Note: The ground lead of power plug must be wired correctly. Pneumatic Part: Adjust knob Pressure Gauge Compress air inlet hose AUX.AIR AUX.Air is for conveyor & pneumatic shuttle use. Service Unit for Whole Printer (at the rear of machine body) - Connect the compressed air line to machine service unit. Please use only clean and dry air. - Set pressure of main service unit for machine operation to 5-6 bar. 2.2

6 Machine Setup Ink Cup lnstallation: 1. Cover ink cup by thin steel plate upside down as right diagram. Remark: The image side of plate cover faces ink cup. 2. Insert ink cup setup unit into thin steel plate with ink cup and then turn it upside down. ink cup setup unit insert setup unit into thin steel plate turn upside down 3. Move ink cup holder to back side. Release ink cup holder swing arm lock (*) and lift up ink cup holder. ink cup holder swing arm lock (*) There is no swing arm lock for holders of Ø60mm and Ø70mm ink cups. 4. Place ink cup setup unit with ink cup and steel plate on ink cup platform. Buckle rear hole of steel plate with rear registration pin of platform. rear registration pin 3.1

7 Machine Setup Ink Cup lnstallation: 5. While slide ink cup setup unit out, put hand on ink cup top to stay it on plate. Buckle front hole of steel plate with front registration pin of ink cup platform. front registration pin 6. Push ink cup against the internal back side of the ink cup holder. Then pull down the swing arm and tighten swing arm lock. swing arm lock 7. Release bleeding screw of ink cup. bleeding screw 8. Use allen key to adjust ink cup holder pad position. (This step apply for first setup of new ink cup holder) ink cup holder pad 3.2

8 Machine Setup Ink Cup Removal: 1. Tighten ink cup bleeding screw. swing arm lock bleeding screw 2. Release swing arm lock of ink cup holder (*) and lift up swing arm. (*) There is no swing arm lock for holders of Ø60mm and Ø70mm ink cups. 3. Lift up the front side of thin steel plate. Insert ink cup setup unit between ink cup platform and thin steel plate. Push it forward to against rear registration pin. Remove the thin steel plate and ink cup with ink cup setup unit. 4. Hold the ink cup, turn ink cup over and then remove ink cup setup unit and thin steel plate. 5. Clean the ink cup ring and then cover it well. 6. Use thinner to clean the thin steel plate. Apply grease on its surface and store it in plastic bag for prevent oxidation. 3.3

9 Machine Setup Printing Pad Setup: Fasten pad to pad holder by 4 screws Pad holder assembly Mount pad with holder to pad assembly X slide Slide pad assembly to X slide 3.4

10 Machine Setup Pad Clean Tape Setup: pad clean tape platform rotor tape roll tape roll tape roll mount Steps: 1. Insert empty tape roll onto the mount with rotor. 2. Insert new tape roll onto the mount without rotor. 3. Pull tape from the new tape roll and through the pad clean tape platform. The sticky side of tape faces upward. 4. Stick the tape onto the empty roll. 3.5

11 Machine Setup Pad Clean Tape Platform Removal: For printing larger image, it is necessary to remove pad clean tape platform for bigger printing pads. 1. Loosen two lock screws and then remove pad clean tape platform. pad clean tape platform lock screws 2. Install two lock screws of the pad clean tape platform to right hand side of machine. thread holes for lock screws 3. Place the pad clean tape platform onto the lock screws with its mountings and then tighten the screws to secure the platform. mountings lock screws Notes: - set pad clean cycle counter 0 to disable pad clean function. (see page 5.5 for details) 3.6

12 Machine Setup Pad In/Out Cushion: Pad In/Out Cushion Adjustment: Cushion of pad cylinder needs to be adjusted when 2 occasions ocured. a. Carriage moves at high speed and creates bang at both end (should close cushion). b. Carriage becomes very slow at 10 mm from both ends and creates vibration (should open cushion). Use very short handle screw driver, turn clockwise to close; counter-clockwise to open cushion. 2 cushion screws Adjustment of Pad Stop Position for Pad Clean: Steps: 1. Loosen lock knob. 2. Slide the knob and washer left and right to adjust pad stop position for pad clean. Remark: - move to left: pad stop further backward. - move to right: pad stop further outward. washer 3. Tighten the lock knob to fix the stop position. lock knob left right 3.7

13 Machine Setup Worktable Adjustment: Angle Screw Knobs X-Axis Lock Handle X-Axis Screw Knob Up/Down Lock Handle Angle Lock Screw Y-Axis Screw Knob Handwheel Angle Lock Screw Y-Axis Lock Handle X-Axis Adjustment: 1. Release X-axis lock handle. 2. Screw X-axis screw knob to adjust X-axis position. 3. Lock X-axis lock handle to fix X-axis position. Angle Adjustment: 1. Release two angle lock screws and two angle screw knobs. 2. a. Turn Left: Release left angle screw knob and screw right angle screw knob tighty. b. Turn Right: Release right angle screw knob and screw left angle screw knob tighty. 3. After adjustment, tighten two angle screw knobs and two angle lock screws to lock the position. Y-Axis Adjustment: 1. Release Y-axis lock handle. 2. Screw Y-axis screw knob to adjust Y-axis position. 3. Lock Y-axis lock handle to lock Y-axis position. Up/Down Adjustment: 1. Release two Up/Dn lock handles. 2. Turn the handwheel to adjust up/down position. 3. Lock 2 Up/Dn lock handles to lock up/down position. 3.8

14 Machine Setup Effective Printing Area with Pad Clean Attachment: Ink Cup: 90mm. Ink Cup Plafe Size: 100x250mm. Tape Width: 50mm. Recommended Image Size: 40mm with pad clean. 3.9

15 Control Feature Front Control Panel: Emergency Stop Switch: to cut power and air supply of machine at emergency. 2. One cycle mode switch: Adjust auto/semi-auto cycling. (Switch available: without small display panel) 3. Index Switch: spare accessory manual control. 4. Pad In/Out Switch: to move pad in and out in manual mode. 5. Pad Up/Down Switch: to move pad up and down in manual mode. 6. Start Switch: to start machine running or to confirm selected functions. 7. Pad Stroke Depth Switch: to increase or decrease ink/print stroke depth. 8. Parameter Switch. 9. Program Dsiplay. 10. Counter Display. 11. Program Switch: to select printing program. + increase program number. - decrease program number. 4.1

16 Control Feature Pneumatic Control Panel: (RHS of printer) 1. Pad stroke upward speed control knob. to control upward speed of pad stroke. 2. Pad stroke downward speed control knob. to control downward speed of pad stroke. 3. Carriage forward speed control knob. to control forward speed of pad carriage. 4. Carriage backward speed control knob. to control backward speed of pad carriage. Note: 4 speed control knobs are turning clockwise to decrease speed or anti-clockwise to increase. 4.2

17 Control Sequence Machine Startup: 1. Turn on main power switches on printer rear control panel. 2. Release emergency stop switch. 3. Press START switch to turn main air valve on. 4. Press +/- switches to select a suitable program (please refer to the section "Program List"). 5. Press START switch to start selected printing mode. (Please refer to the section "INKING/PRINTING DEPTH ADJUSTMENT" to check the inking and printing depth before start) 1 2 printer rear control panel

18 Control Sequence Manual Mode: 1. Stop machine. Press desired MANUAL FUNCTION switch once. Then corresponding LED of switch will light up. 2. Press START switch to start manual mode. Machine performs printing motion as selected manual function. (please see the section "Manual Printing Functions") 3. Press the selected MANUAL FUNCTION switch once again to stop the manual printing motion manual function switches Manual Printing Functions: Selected Switches Printing Function Printing Motion Pad In/Out Pad in and out printing function Pad moves in and out continuously. Pad Up/Down AND Pad In/Out Pad Up/Down Pad up and down printing function Complete cycle printing function Pad moves up and down continuously. Machine performs one print cycle continuously. Ink once and print once in each cycle. Index Spare 5.2

19 Control Sequence Auto/One Cycle Printing Mode: 1. Turn all manual function switches off (all LEDs of manual function switch turn off). 2. Press start switch once to start auto or one cycle printing mode. (please refer to the section "Program List"). - In one cycle mode, press foot switch once to start one printing cycle. - In auto mode, printing cycle is running continuously. 3. Press foot switch or any manual function switch to stop printing cycle foot switch manual function switches 5.3

20 Control Sequence Inking Depth Adjustment: 1. Stop machine at ink position (pad at the rear) in manual mode. Remark: - Counter display shows inking depth value. - Program display shows "d1", code number of ink depth. 2. Press PAD STROKE DEPTH switch to increase or decrease ink depth value. counter display program display 1 2 Printing Depth Adjustment: 1. Stop machine at print position (pad at the front) in manual mode. 2. Press PAD STROKE DEPTH switch to increase or decrease print depth value. Remark: - Print depths for different printing stations are independent. Counter display shows printing depth value. Program display shows code numbers of print depths: d2: print depth for single color printing or for 1st color of multi-color printing. - If program display does not show proper code numbers, turn PAD UP/DOWN switch on once. Print position Ink position Note : - A long beep sound indicates that value has reached the maximum or minimum. - Maximum value is 75mm. - Minimum value is 10mm. - Pad clean depth will be set automatically base on the inking depth. So only inking or printing depth is required to adjust. 5.4

21 Control Sequence Other Parameters: Pad Dwell/Delay Time (L1): 1. Press Parameter switch until L1 on screen. 2. Press Program switch to increase or reduce the delay or dwell time value. 1 Remark: Set all of marked " * " programs time. The setting range is 0 to 9.9s. Each time increment is 0.1s. 2 (L2)--Spare. (L3)--Spare. Remote Control (L4): 1. Press Parameter switch until L4 on screen. 2. Repeat pressing Program switch to switch on or off remote control function. Remark: - If setting "ON", use extra start switch to control machine start printing. The foot switch is only for stopping printing. - If setting "OFF", step on foot switch to start printing cycle in one cycle printing mode. (See page 8.2 for remote control wiring example.) Pad clean cycle counter (L5) 1. Press Parameter switch until L5 on screen. 2. Press Program switch to set number of printing cycle for doing pad clean once. Remark: - value range is 0-99 cycles. - each increment/decrement is 1. - hold the +/- Key for longer then half second to increase or decrease value continuously. - when value = 0, pad clean function will be disable. 5.5

22 Control Sequence Counter Reset: 1. Turn machine power off. 2. Turn machine power on. 3. Press COUNTER RESET switch on. 4. Start machine up again as section "MACHINE STARTUP". AND Reset Parameter Values to Default: Parameter values, including stroke depths, snd delay times, can be reset to default setting by the following procedure: 1. Turn machine power off. 2. Press COUNTER RESET switch on and hold. Turn machine power on at the same time. Keep holding COUNTER RESET switch for 2 seconds and then release. 3. Start machine up again as section "MACHINE STARTUP" described. AND

23 Control Sequence Stop and Restart: 1. Foot switch: Press once to stop printer for changing mode or program. Press START switch once to restart. Foot switch 2. Emergency Stop Switch: Hit emergency stop switch to cut the power suppy and main air at emergency. Turn the mushroom head clockwise to release emergency stop switch. (Printer will be no reaction until redo the control sequence "MACHINE STARTUP"). Emergency Stop Switch Switch off the machine: 1. Stop printing cycle. 2. Turn machine power off

24 Programm List Progr. No. Function Description 01 Single Print Machine operates in continuous cycle. Pad picks up ink once and prints once. 02 Double Inking Machine operates in continuous cycle. Pad picks up ink twice, prints once for better print opacity. 03 Double Print Machine operates in continuous cycle. Pad picks up ink once, prints twice for better ink release. 04* Delay before Print Machine operates in continuous cycle. Pad delay 0.0 to 9.9 seconds before printing. (Suitable for slow drying ink) 05 One Cycle Machine performs one print cycle when signal by foot switch. Cycle starts in giong back for inking. 06 One Cycle + 02 Machine performs one print cycle w/ double inking when signal by foot switch. 07 One Cycle + 03 Machine performs one print cycle w/ double print when signal by foot switch. 08* One Cycle + 04 Machine performs one print cycle w/ delay before print when signal by foot switch. 09 Reversion Cycle Machine performs one print cycle when signal by foot switch. Single print cycle starts in at printing. 10 Two Cycle Machine performs one print cycle when signal by foot switch. Pad picks up ink twice and prints twice. 11 Single Index Machine operates in continuous cycle with conveyor. Single print, 1 index per cycle. 12 Single Index + 03 Machine operates in continuous cycle with conveyor. Double print, 1 index per cycle. 13* Single Index + 04 Machine operates in continuous cycle with conveyor. Delay before print, 1 index per cycle. 14 Single Index + 10 Machine operates in continuous cycle with conveyor. Double print cycle, 1 index per cycle. 15 Double Index Machine operates in continuous cycle with conveyor. Single print, 2 index per cycle. 16 Double Index + 03 Machine operates in continuous cycle with conveyor. Singleprint, 2 index per cycle. 17* Double Index + 04 Machine operates in continuous cycle with conveyor. Delay before print, 2 index per cycle. 18 Double Index + 10 Machine operates in continuous cycle with conveyor. Double print cycle, 2 index per cycle Color Shuttle Machine operates in continuous 2 color print cycle with shuttle attachment. 1 inking, 2 prints Color Shuttle color shuttle print when signaled by foot switch Color Shuttle Machine operates in continuous 3 color print cycle with shuttle attachment. 1 inking, 3 prints Color Shuttle color shuttle print when signaled by foot switch Color Shuttle Machine operates in continuous 4 color print cycle with shuttle attachment. 1 inking, 4 prints 24 4 Color Shuttle color shuttle print when signaled by foot switch. 6.1

25 Programm List Progr. No. Function Description 25 2 Color Shuttle Machine operates in continuous 2 color print cycle with shuttle attachment. Print on fi rst & third positions Color Shuttle color shuttle print when signaled by foot switch Color Shuttle Machine operates in continuous 2 color print cycle with shuttle attachment. Print on second & third position Color Shuttle color shuttle print when signaled by foot switch. 29 Roller Print Machine operates in continuous cycle with 2 color shuttle & turning attachment for printing round product. 30 Roller Print + 05 Perform one roller print cycle when signal by foot switch. 31* Dwell Machine operates in continuous cycle. Pad comes down pressing on product surface and dwell 0.0 to 9.9 seconds when printing. Each increment is 0.1 sec. (For texture surface) 32* Dwell + 05 Perform dwell print cycle when signed by foot switch. 33* Dwell + 11 Machine operates in continuous dwell print cycle with conveyor. Index once per cycle. 34* Dwell + 15 Machine operates in continuous dwell print cycle with conveyor. Index twice per cycle. Remark: Marked " * " programs need to adjust delay/dwell time in L1 parameter setting. L1 parameter setting pls. refer to page 5.5 of control sequence section. (Program# functions are unavailable for HVA-90 & HVA-100 ) (Program#21-28 functions are unavailable for PP-21N) 6.2

26 Sensor Layout PS2 PS1 PS5 PS6 PC1 PS1: Pad stroke home sensor. PS2: Optical sensor. PS5: Pad Carriage Home Switch. PS6: Pad Carriage Actuate Switch. PC1: Pad Clean Sensor. 7

27 Electrical Circuit Diagram 220V~240V POWER SUPPLY L J4 N POWER emergency stop SWITCH 1A Fuse L N L N 240V 0V NOISE FILTER TRANSFORMER J5 J9 0V RED 9V RED 0V ORG 9V ORG J7 J8 J OUT (PC1) foot switch (PS6) (PS1) - OUT + - (PS5) (PS2) OUT J12 J1 + Name Description Name Description SV1 Main Air Solenoid PS1 Pad stroke home sensor SV2 Pad Stroke Solenoid PS2 Optical sensor SV3 Pad Carriage Solenoid PS5 Pad Carriage Home Switch SV5 Pad Dwell Solenoid PS6 Pad Carriage Actuate Switch SV6 Middle Stop Solenoid PC1 Pad Clean Sensor SV8 Tape Rotor Solenoid (SV2) (SV3) (SV6) (SV1) (SV8) (SV5) "+" switch "-" switch KP-100 PCB (HVA90-EC-A102) 8.1

28 Electrical Circuit Diagram - Remote Control Connection KPDSP-150 PCB J1 J5 J9 J7 KP-100 PCB (HVA90-EC-A102) J12 J1 J4 J8 J10 Remote Start Input 24VDC Complete Cycle Output Machine Ready Output 24VDC 8.2

29 Pneumatic Circuit VT-307-5G-02 (15-PVA-120) (SV5) (LFR-1/4-DB-7-5M-MINI+MA /8-EN) (21-PSU-032) (SERVICE UNIT OF MACHINE) VQZ3121-5GB-02F (KP200-PVA-010) (SV2) VQZ3121-5GB-02F (KP200-PVA-010) (SV1) (PAD CARRIAGE CYLINDER) L-CG1BN (10-PCY-030) VQZ3121-5GB-02F (KP200-PVA-010) (SV3) SPC06-G01 CDC (15-PFT-311) VT-307-5G-02 (15-PVA-120) (SV6) TAPE ROTOR CYLINDER AEVC I-P (HVA150-PCY-050) VT-307-5G-02 (15-PVA-120) (SV8) (ASC100-06) (KP100-PFR-011) PAD STROKE CYLINDER L-CG1BA32-75 (KP90-PCY-010) (ASC100-06) (KP100-PFR-011) (ASC100-06) (KP100-PFR-011) (ASC100-06) (KP100-PFR-011) 9

30 Maintenance There are some regular maintenance works to keep printer in smooth operation. 1. Lubrication: Please do lubricantion weekly on the parts of machine as shown in the following drawing: a. Grease nipples of pad carriage 2. System Cleaning: Please weekly check: - Clean-up the scale ruler. scale ruler a 3. Check Service Unit: Check unit daily: - maintain operation pressure at 5-6 bar. - make sure service unit tube is clean. - discharge water from the bottom of unit tube. discharge water from here 10.1

31 Maintenance HOW TO MAINTAIN YOUR PAD PRINTER IN GOOD CONDITION Section A: Starting from the pneumatic system. 1. Air must be clear with NO water or oil: Popular problem: As the service unit deposit with excessive water and oil, - Water will flow into each cylinder and valve. - The whole printer can not operated. - Rubber ring will be damaged. - Damage rubber ring makes solenoid valve can not be worked properly or leaks air. - The whole printer can not operated. Solution: a. The best way is to install a filter or dryer at back of air compressor for clean air. (With less unknown particles) b. To keep 4.5 bars air pressure or above - single color printing setup. To keep 6.0 bars air pressure or above - double and 4 color set up or above. Section B: Mechanical Checking. 1. To apply and maintain appropriate amount of lubrication oil on parts, particularly on easy-rusty areas. Example: Shaft; lead screws; doctor blade mounting parts etc To keep on screwing up the easy-loose screws. Reason for easy-loose screws: The vibration from the movement of operation. 3. To keep ink away from the worktable slide and working platform. Keep clean and tidy. 4. How to treat the printer which is not used for long time: To cover the whole printer well by sealed plastic bag. To apply anti-rusty oil onto easy-rusty areas. To ensure the power switch being off. Section C: Electricity. 1. General speaking, electricity format should be kept on AC 220V-240V. If the voltage differential is too big, voltage regulator is needed. Example: 220V-240V is appropriate. - If the voltage is below the range, printer will be not worked. - If the voltage is over the range, printer will be broken down due to the overheat of components. Section D: Maintenance on Pad. 1. On average, pad can be stored for 6 months. (The higher room temparature, the shorter the life of pad is.) 2. Ink must be removed from pad after each printing job and be stored in a cool place. 3. To remove heavy weight subject from the pad. 4. Pad does never be put into any plastic bag. 10.2

32 Maintenance Section E: Daily Checking Issues. 1. The electricity voltage should be kept on AC 220V-240V; the earth line must be connected properly. 2. Air inflow pressure must be not less than 4.5 Bars. If not, printer may be malfunction or printing distortion is induced. 3. Right air pressure for doctor blade: a. 1.5 ~ 2.0 Bars for thin steel plate. b. 2.0 Bars for 10mm steel plate. c. For 10mm plate, doctor blade should be replaced if the air pressure is over 3 Bars. 4. Water deposit in water regulator: If there is some water deposited in the Water Regulator, extra. -Air Cleaning Equipment OR -Refrigerator Air Dryer should be installed. It can minimise the probability of electrical parts damaged by the water. 5. Smoothness of air release process in the pneumatic system: General speaking, each movement of printer was motivated by the pneumatic system. The air comes from Silencer. If Silencer was blocked, the speed of movement of printer would be slower. In this case, silence should be deposited into thinner for 2 hours for cleaning up and then install it back or replace the part. 6. After each printing job or working day, workers have to handle the printer and all relevant printing softwares carefully in good condition for the coming printing job or working day. Open Ink Tray System: - ink residue must be taken away from the ink tray. - the ink on plate must be cleaned up with thinner and be coated with oil to avoid oxidisation. Ink Cup System: - ink cup must be unloaded from the plate (avoid chemical reaction between ink and plate) - unloaded ink cup must be covered by the polymer plate cover. (stop ink exposure to air - stabilize ink viscosity) - the ink on plate must be cleaned up with thinner and be coated with oil to avoid oxidisation. 10.3

33 Electrical Spare Parts List 15-EC-000 Emergency stop switch (AVW401-R) AN10-EC-620 EE-SX672 Sensor 15-EC-131 Proximity sensor TL-Q5MC1(Omron) HVA90-EC-001 Pad stroke depth switch 15-EC-590 Micro switch HVA90-EC-010 Eprom KP EC-753 Fuse (1A) HVA90-EC-020 Eprom KPDSP EC-862 Filter HVA90-EC-A020 KPDSP-150 completedisplay PCB (with Eprom) 15-EC-914 Power cord 3m without plug HVA90-EC-A102 KP-100 complete control PCB (with Eprom) 15-EC-A974 Foot switch HVA90-MEC-020 Front panel label 50-EC-270 Transformer 9v x 2 20va 230vac HVA90-MEC-031 Counter panel label AN10-EC Power socket with switch KP90-EC-A050 Buzzer assembly 11

34 Mechanical Spare Parts List 15-PC-170 Rubber ring I.D.20mmxO.D.30mmx L.3mm (pair) AN10-PC-140 Scale ruler 2.7mm x 20mm x 180mm AN10-PC-400 Compression spring 2mm(14)#O.D.21mm L.22mm DRE Nylon spacer I.D.20mm O.D.35mm L.18mm HVA90-SC-010 Safe side cover (6x235x435mm) KP200-MB Way Manifold 21-MB-131 Gray sponge (53x72x85mm) 15-MEC-010 Pad stroke adjustable plate 12

35 Pneumatic Spare Parts List 10-PCY-030 Pad stroke cylinder (L-CG1BN ) 15-PFT-311 Quick connector coupling (SPC06-G01 CDC) 10-PFT-010 Fitting (CK-1/4-PK-4KU) 15-PVA-120 3/2 single solenoid valve pt 1/4 (VT-307-5G-02) 10-PFT-020 Fitting (GCK-1/4-PK-4KU) 21-PFT Swivel elbow connector (GCK-M5-4 ) 15-PFT-020 Fitting (CK-1/4-PK-6KU) 21-PSU-032 Filter regulator (LFR-1/4-DB-7-5M-MINI+ MA /8-EN) 15-PFT-030 Fitting (CK-1/8-PK-4KU) HVA150-PCY-050 Tape Rotor Cylinder (AEVC I-P) 15-PFT-050 Fitting (GCK-1/8-PK-4-KU) HVA90-PSA Hydraulic shock absorber (YSR MC-SA-123R) 15-PFT-150 Fitting (GCK-1/4-PK-6-KU) KP100-PFR-011 1/8" Flow regulator (ASC100-06) 15-PFT-240 M6 Elbow grease nipple KP200-PVA-010 1/4" solenoid valve (VQZ3121-5GB-02F) 15-PFT-280 T-connector (T-6-4-6) KP90-PCY-010 SMC CYLINDER ( L-CDGIBA ) 13

36 Spare Parts List (Accessory) 10-ICT-A010 Ink cup platform ass'y for 102 x 250mm magnetic plate 21-WT-A X Y table top assembly 15-PA mm Pad mounting plate (23.2x50x67MM) AMIC-CMIC-A020 Dia.90mm AMIC ink cup ass'y with ZIRCONIA ceramic ring 15-PA mm Pad mounting plate CMIC-A050.1 Ink cup set up unit (for dia.60mm~ 90mm ink cup 15-PA mm Pad mounting plate ICH-A mm swing arm ink cup holder ass'y 15-PA mm Pad mounting plate ICH-A mm swing arm ink cup holder ass'y 15-PA-A004 Pad holder ass'y ICH-A mm swing arm ink cup holder ass'y HVA90-PC-A Pad clean assembly ICH-A mm swing arm ink cup holder ass'y 21-WT-A000 Complete work table ass'y ICH-A mm swing arm ink cup holder ass'y 21-WT-A001 Up/down platform assembly ICH-A Dia.90mm swing arm ink cup holder ass'y 14

37 Spare Parts List (Accessory) ICH-A Dia.70mm swing arm ink cup holder ass'y NIC-A Dia.70mm ceramic magnetic ink cup + protective plate NIC-A Dia.90mm ceramic magnetic ink cup + protective plate NIC-A mm x 102mm x 250mm magnet plate ass'y NIC-A Dia.60mm ceramic magnetic ink cup + protective plate NIC-A048 Dia.90mm AMC ceramic magnetic ink cup+protective plate NIC-A049 DIA.90mm ceramic magnetic ink cup +protective plate 15