CONTENTS. Technical Information. PH450G/SC450G/ISC450G ph/orp/conductivity Converters HART Communication TI 12A01A01-60EN

Transcription

1 Technical Information PH450G/SC450G/ISC450G ph/op/conductivity Converter HAT Communication CONTENTS What i HAT Communication?...2 Downloading and intalling DD file...2 Before uing FieldMate...2 Intalling the DD File...3 Connecting Setup Tool...3 tion Available via HAT Communication...3 Operational Precaution...4 Setting on the PH450G/SC450G/ISC450G and a etup tool (communication tool):...4 Operation with handling all the parameter of the PH450G/SC450G/ ISC450G:...4 DD Online eter for PH450G (Device reviion 2, DD file reviion 2)... 4 DD Online eter for SC450G (Device reviion 2, DD file reviion 2) DD Online eter for ISC450G (Device reviion 2, DD file reviion 2)...36 eviion Information...51 Copyright Sep t Edition Oct. 2017

2 HAT Communication 2 Thi document decribe HAT communication by the PH450G/SC450G/ISC450G. Before communicating uing the HAT protocol, refer to the Uer Manual for the PH450G/ SC450G/ISC450G for detail of the parameter. HAT i a regitered trademark of FieldComm Group. What i HAT Communication? HAT Communication uperimpoe pecific waveform called HAT Communication waveform on the 4 20 ma analog ignal from a PH450G/SC450G/ISC450G to enable remote intercommunication between the online PH450G/SC450G/ISC450G and a etup tool (*). *: FieldMate, Plant eource Manager (PM), or a handheld HAT communicator uch a the 475 Field Communicator may be ued a the etup tool. It i highly recommended to ue the latet model of each etup tool. Downloading and intalling DD file To enable HAT communication between a PH450G/SC450G/ISC450G and etup tool, the device decription (DD) file of the PH450G/SC450G/ISC450G need to be intalled in the etup tool. The DD file contain the HAT communication detail and menu configuration pecific to the PH450G/SC450G/ISC450G. FieldMate contain the verion of DD file at the time when old. To download the latet verion of DD file, viit our library by clicking the following link. You can find and down load the file you need from Software in Document & Download. *: Thi addre i ubject to change without prior notice. If the above addre cannot be acceed, conult your nearet ale office or the agency from which you purchaed the product. Before uing FieldMate Before uing FieldMate, check the reviion of Device File. Compatibility among reviion of PH450G/SC450G/ISC450G, FieldMate and DD file Device PH450G/ SC450G/ ISC450G Product FieldMate DD of Field Communicator Device verion 02 eviion of Device File DD file reviion in Device File Correponding device reviion DD file reviion 3.05 or later You can check the device verion by preing the zoom on the main menu of PH450G/ SC450G/ISC450G, a hown in the figure 1. HAT ID xxxxxx Software eviion 1.26 HAT Device eviion 02 Logbook Figure 1 Diplay of firmware reviion No. 1t Edition : Oct. 2017(YK) All ight eerved. Copyright 2017, Yokogawa Electric Corporation

3 HAT Communication 3 Intalling the DD File For how to intall the DD file, ee the repective documentation for the etup tool you ue. The following how how to intall the latet DD file in the Yokogawa etup tool, FieldMate. that the following decription aume intallation in FieldMate If the verion i upgraded later, the following decription may not match. In thi cae, pleae ee the latet documentation for FieldMate. Obtaining and decompreing the DD file Download the DD file from Yokogawa webite. DD file are downloadable a ZIP file (when downloading from the webite of FieldComm Group, a compreed DD file will be downloaded with the name of dd.zip). Intalling the Device Decription (DD) file of FieldMate Intall the latet DD file you obtained by following the intruction decribed in the manual of FieldMate. on DD file reviion and device reviion When uing HAT communication of a PH450G/SC450G/ISC450G, it i neceary to ue the DD file that matche the reviion of the PH450G/SC450G/ISC450G device ued. Make ure to check they match before ue, a follow. (1) Checking the PH450G/SC450G/ISC450G device reviion On the main creen pre the zoom key. Pre Enter repeatedly until reviion information on the firmware and HAT device i diplayed. (2) Checking the DD file reviion DD file are tored with filename beginning with a four-digit number uch a 0102.xxxdd. The firt two digit, 01 in the example above, indicate the device reviion. The following two digit, 02 in the example above, indicate the DD reviion. Ue the latet reviion of the DD file that matche the device reviion. Connecting Setup Tool You can connect the etup tool to any junction terminal uch a one in the central control room, a converter junction box, or omewhere within the tranmiion loop, a long a the load reitance i 250 ohm or larger between the power upply and the terminal to which you want to connect the etup tool. Connect the etup tool in parallel with the load reitance. It i polarityinenitive. tion Available via HAT Communication Almot all PH450G/SC450G/ISC450G function acceible via the front panel diplay of the PH450G/SC450G/ISC450G are available via HAT communication. The following page how the lit of parameter for HAT communication between PH450G/ SC450G/ISC450G and the etup tool with ome note regarding their diplay and etting. For further information on the parameter, read the correponding intruction manual. The data on the lit wa obtained by uing Yokogawa FieldMate. It i highly recommended to ue a device DTM (device type manager) with FieldMate, otherwie ome parameter might not be diplayed or et appropriately. efer to each remark poted on column of the lit. ead an intruction manual of FieldMate to know how to tartup / operate the device DTM. The following lit decribe each parameter. refer to read only, refer to rewritable.

4 HAT Communication 4 Operational Precaution Setting on the PH450G/SC450G/ISC450G and a etup tool (communication tool): While etting on a etup tool (ex. FieldMate), don t perform etting on the PH450G/SC450G/ ISC450G at the ame time. Operation with handling all the parameter of the PH450G/SC450G/ISC450G: PH450G/SC450G/ISC450G ha a lot of parameter. Acceing many parameter may take everal minute. DD Online eter for PH450G (Device reviion 2, DD file reviion 2) CAUTION Ue a device DTM or the front panel of the device to perform etting/checking. Built-in DTM may replace character with unintended one or diable etting appropriately. that ºC i diplayed a ッ-C, ºF i diplayed a ッ-F.

5 HAT Communication 5 In the following lit, thoe item with bracket [ ] or [()] are valid when the parameter are et a decribed in thoe bracket. PH450G eter eter Proce Zoom Zoom enor PV [Senor type: ph] or type: ph, ph+rh, ph+op)] ph SV ッ -C ッ -F TV [Senor type: OP] or type: OP, ph+op, rh)] Zero [Senor type: ph] or type: ph, ph+rh, ph+op)] Slope [Senor type: ph] or type: ph, ph+rh, ph+op)] Senor mv [Senor type: ph, ph+op] OP zero [Senor type: OP] or type: OP, ph+op)] OP lope [Senor type: OP] or type: OP, ph+op)] OP enor mv [Senor type: OP] or type: OP, ph+op)] rh zero type: rh, ph+rh)] rh lope type: rh, ph+rh)] rh enor mv type: rh, ph+rh)] Impedance 1 [Input 1 impedance: Low] Impedance 2 [Input 2 impedance: Low] mv mv mv mv mv mv mv kohm kohm Zoom output ma1 value ma ma2 value ma S1 perc S2 perc S3 perc S4 perc Zoom device Serial number Software eviion Device eviion Logbook Calib/wah

6 HAT Communication 6 Commiioning PH450G eter eter Senor etup Senor Type ph OP ph+op Meaurement etup Mea type [Senor type: ph+op] ph OP ph+op rh+ph rh Temp etting Temp enor Pt1000 Pt100 5K1 3K Balco 8k K8 PTC10K Temp unit ッ -C ッ -F The ue of Built-in DTM diable ph+op to be elected. The ue of Builtin DTM diable ph+op or rh+ph to be elected. Temp compenation Calib. Setting Zero/ Slope unit [Senor type: ph] Temp comp Auto Manual Man value (Temp unit: ッ -C) to (Temp unit: ッ -F) ef temp (Temp unit: ッ -C) to (Temp unit: ッ -F) Comp method [Senor type: ph] or type: ph, ph+rh, ph+op, rh)] TC [Comp method: TC] OP comp method [Senor type: OP] or type: OP, ph+op)] OP TC [OP comp method: TC] Buffer et [Senor type: ph] or type: ph, ph+rh, ph+op)] Zero unit [Senor type: ph] or type: ph, ph+rh, ph+op)] None TC Matrix NEN to (Temp unit: ッ -C) to (Temp unit: ッ -F) None TC -1 1 (Temp unit: ッ -C) to (Temp unit: ッ -F) Nit DIN US Uer defined mv ph ッ -C ッ -F ッ -C ッ -F ph/ ッ -C ph/ ッ -F mv/ ッ -C mv/ ッ -F

7 HAT Communication 7 PH450G eter eter Zero/ Slope unit [Senor type: ph] Limit and timing Slope unit [Senor type: ph] or type: ph, ph+rh, ph+op)] Zero hi lim [Senor type: ph] or type: ph, ph+rh, ph+op)] Zero lo lim [Senor type: ph] or type: ph, ph+rh, ph+op)] Slope hi lim [Senor type: ph] or type: ph, ph+rh, ph+op)] Slope lo lim [Senor type: ph] or type: ph, ph+rh, ph+op)] OP Zero hi lim [Senor type: OP] or type: OP, ph+op)] OP Zero lo lim [Senor type: OP] or type: OP, ph+op)] OP Slope hi lim [Senor type: OP] or type: OP, ph+op)] OP Slope lo lim [Senor type: OP] or type: OP, ph+op)] rh Zero hi lim type: rh, ph+rh)] rh Zero lo lim type: rh, ph+rh)] rh Slope hi lim type: rh, ph+rh)] rh Slope lo lim type: rh, ph+rh)] mv/ph to to to t o 11 7 Stab time 2 to 30 Cal int 1 to 250 ph [Zero unit: ph] mv [Zero unit: mv] ph [Zero unit: ph] mv [Zero unit: mv] mv/ph mv/ph mv mv 8 mv mv 8 d

8 HAT Communication 8 PH450G eter eter Output etup Impedance etting Zero/ Slope/ ITP Zero [Senor type: ph] or type: ph, ph+rh, ph+op)] Slope [Senor type: ph] or type: ph, ph+rh, ph+op)] ITP [Senor type: ph] or type: ph, ph+rh, ph+op)] OP zero [Senor type: OP] or type: OP, ph+op)] OP lope [Senor type: OP] or type: OP, ph+op)] rh zero type: rh, ph+rh)] rh lope type: rh, ph+rh)] Input 1 impedance Low Imp. 1 low limit [Input 1 impedance: Low] Imp. 1 high limit [Input 1 impedance: Low] Input 2 impedance Low Imp. 2 low limit [Input 2 impedance: Low] Imp. 2 high limit [Input 2 impedance: Low] to to to to to to ma1 etup Type Control Output Simulate [Type: ] P PI PID ph [Zero unit: ph] mv [Zero unit: mv] mv/ph ph mv mv kohm kohm kohm kohm The ue of Built-in DTM caue an error and diable a value to be entered when it i outide the range to The ue of Builtin DTM caue an error and diable a value to be entered when it i outide the range to The ue of Built-in DTM caue an error and diable a value to be entered when it i outide the range to The ue of Builtin DTM caue an error and diable a value to be entered when it i outide the range to

9 HAT Communication 9 PH450G eter eter PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Burn [Type: Output] [Type: Output] Lin 0 [Type: Output (: Linear)] Lin 100 [Type: Output (: Linear)] Burn [Type: Output] Damping time [Type: Output] [Type: Simulate] [Type: Simulate] PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere Low 180 Linear Table PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] Low 360 Simulate ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H]

10 HAT Communication 10 PH450G eter eter ma2 etup Type Control Output Simulate [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Burn [Type: Output] [Type: Output] Lin 0 [Type: Output (: Linear)] Lin 100 [Type: Output (: Linear)] P PI PID PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere Low 180 Linear Table PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H]

11 HAT Communication 11 PH450G eter eter Burn [Type: Output] Damping time [Type: Output] [Type: Simulate] [Type: Simulate] Low 360 Simulate S1 etup Type Control Alarm Simulate HOLD Wah [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] P PI PID PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere PF DC Alarm ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] p/m

12 HAT Communication 12 PH450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] [Type: Wah] Inter. time [Type: Wah] Wah time [Type: Wah] ec. time [Type: Wah] Man. wah [Type: Wah] Cont. wah [Type: Wah] PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] Low Hard + Soft Hard Only ON/ ON OFF HOLD contact Wah to to to 1 diable enable diabled + imp2 high enabled + imp2 high diable enable ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] h min min The ue of Builtin DTM diable Hard + Soft to be elected. Ue a device DTM or et at the front panel diplay. The ue of Builtin DTM diable diabled + imp2 high or enabled + imp2 high to be elected.

13 HAT Communication 13 PH450G eter eter S2 etup Type Control Alarm Simulate HOLD Wah [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] P PI PID PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere PF DC Alarm ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] p/m

14 HAT Communication 14 PH450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] [Type: Wah] Inter. time [Type: Wah] Wah time [Type: Wah] ec. time [Type: Wah] Man. wah [Type: Wah] Cont. wah [Type: Wah] PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] Low Hard + Soft Hard Only ON/ ON OFF HOLD contact Wah to to to 1 diable enable diabled + imp2 high enabled + imp2 high diable enable ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] h min min The ue of Built-in DTM diable Hard + Soft to be elected. The ue of Builtin DTM diable diabled + imp2 high enabled + imp2 high to be elected.

15 HAT Communication 15 PH450G eter eter S3 etup Type Control Alarm Simulate HOLD Wah [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] P PI PID PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere PF DC Alarm ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] p/m

16 HAT Communication 16 PH450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] [Type: Wah] Inter. time [Type: Wah] Wah time [Type: Wah] ec. time [Type: Wah] Man. wah [Type: Wah] Cont. wah [Type: Wah] PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] Low Hard + Soft Hard Only ON/ ON OFF HOLD contact Wah to to to 1 diabled enabled diabled + imp2 high enabled + imp2 high diable enable ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] h min min The ue of Builtin DTM diable Hard + Soft to be elected. Ue a device DTM or et at the front panel diplay. The ue of Builtin DTM diable diabled + imp2 high or enabled + imp2 high to be elected.

17 HAT Communication 17 PH450G eter eter S4 etup Type Control Alarm Simulate HOLD Wah [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID) ] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] P PI PID PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] direct revere PF DC Alarm ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] p/m

18 HAT Communication 18 PH450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] [Type: Wah] Inter. time [Type: Wah] Wah time [Type: Wah] ec. time [Type: Wah] Man. wah [Type: Wah] Cont. wah [Type: Wah] PH [Senor type: ph] or [Senor type: ph+op (Mea type: ph, ph+rh, ph+op)] TEMPEATUE OP [Senor type: OP] or [Senor type: ph+op (Mea type: OP, ph+op)] H [Senor type: ph+op (Mea type: rh, ph+rh)] Low Hard + Soft Hard Only ON/ ON OFF HOLD contact Wah to to to 1 diabled enabled diabled + imp2 high enabled + imp2 high diable enable ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] ph [: PH] ッ -C, ッ -F [: TEMPEATUE] mv [: OP] rh [: H] h min min The ue of Builtin DTM diable diabled Hard + Soft to be elected. The ue of Builtin DTM diable diabled + imp2 high or enabled + imp2 high to be elected

19 HAT Communication 19 PH450G eter eter HOLD etup HOLD L/F Lat Fixed ma1 Fixed [HOLD L/F: Fixed] to ma ma2 Fixed [HOLD L/F: Fixed] to ma HOLD dur. Cal/wah diabled enabled Error config ph too high [Senor type: ph] or type: ph, ph+rh, ph+op)] ph too low [Senor type: ph] or type: ph, ph+rh, ph+op)] Temp too high Temp too low Matrix config [Senor type: ph] or type: ph, ph+rh, ph+op)] OP too high [Senor type: OP] or type: OP, ph+op)] OP too low [Senor type: OP] or type: OP, ph+op)] rh too high type: rh, ph+rh)] rh too low type: rh, ph+rh)] Cal time exc Wah Error Imp. 1 high Imp. 1 low Imp. 2 high Imp. 2 low

20 HAT Communication 20 PH450G eter eter Logbook config Senor logbook Error on Error off T.C. Zero lo lim Zero hi lim Slope lo lim Slope hi lim Stab. Time Imp.1 lo lim Imp.1 hi lim Imp.2 lo lim Imp.2 hi lim ma logbook ma etup Hold fixed value PID etpoint PID range Manual reet PID I time PID D time Burn Linear Damping time Contact logbook Contact etup PID etpoint PID range Manual reet PID I time PID D time Control type DC period time Max pule freq. Alarm etpoint Alarm direction Alarm hyterei Alarm delay time Wah etup Erae logbook Calibration Senor Predictive Maint All logbook logbook full No Ye Baic etup Tag Alphanumeric value Ditributor Model Device information Decriptor Alphanumeric value Meage Alphanumeric value Poll addr 0 to 15 Num rep pream 0 to 255 A confirmation meage appear before deleting. The ue of Built-in DTM diable the etting appropriately.

21 HAT Communication 21 PH450G eter eter eview Model Ditributor Write protect Manufacturer Dev id Tag Decriptor Meage Date Univeral rev Fld dev rev Software rev Poll addr Num rep pream : The ue of Built-in DTM may make character diplayed a unintended one. ºC i replaced with ッ -C, ºF i replaced with ッ -F. Ue a device DTM or check at the front panel diplay. DD Online eter for SC450G (Device reviion 2, DD file reviion 2) CAUTION Ue a device DTM or the front panel diplay to perform etting/checking. Built-in DTM may replace character with unintended one or diable etting appropriately. that ºC i diplayed a ッ-C, ºF i diplayed a ッ-F.

22 HAT Communication 22 In the following lit, thoe item with bracket [ ] or [()] are valid when the parameter are et a decribed in thoe bracket. SC450G eter eter Proce PV S/cm, S/m [Meaure: Cond ppb [Meaure: Conc only] O.cm [Meaure: e only (Mea unit: /cm)] O.m [Meaure: e only (Mea unit: /m)] SV ッ -C TV S/cm, S/m [Meaure: Cond ppb [Meaure: Conc only] O.cm [Meaure: e only (Mea unit: /cm)] O.m [Meaure: e only (Mea unit: /m)] Zoom Zoom enor Fact CC /cm, /m Adj CC /cm, /m Method SC1 Method SC2 Polarization Ohm ohm USP Zoom output ma1 value ma ma2 value ma S1 perc S2 perc S3 perc S4 perc Zoom device Serial number Software eviion Device eviion Logbook Calibration Commiioning Input contact Diable Factor 10 ma1 Factor 10 ma2 Factor 10 ma1+2 Meaurement etup Meaure Cond only e Only Con conly Cond+Conc Configure enor Senor type 2-elec 4-elec Mea unit /cm /m Fact CC to 5 [Mea unit: /cm] to 500 [Mea unit: /m] The ue of Built-in DTM diable Factor 10 ma1+2 to be elected. The ue of Built-in DTM diable Cond and Conc to be elected.

23 HAT Communication 23 SC450G eter eter Temp etting Temp enor Pt1000 Pt100 Ni100 8k55 Pb36 (JIS6k) Temp unit ッ -C ッ -F Temp compenation Temp comp Auto Manual Man value [temp unit: ッ -C] to [temp unit: ッ -F] ッ -C ッ -F ef temp [temp unit: ッ -C] to [temp unit: ッ -F] ッ -C ッ -F Method SC1 None TC Nacl Matrix Matrix SC1 [Method SC1: Matrix] Ammonia 0-50ppb Morpholine ppb Ammonia H2SO H2SO H2SO NaOH 0-15 NaOH HCl ppb HCl 0-18 Hcl24-44 HNO HNO Uer defined 1 Uer defined 2 TC SC1 [Method SC1: TC] [temp unit: ッ -C] [temp unit: ッ -F] / ッ -C / ッ -F Method SC2 None TC Nacl Matrix Matrix SC2 [Method SC2: Matrix] Ammonia 0-50 ppb Morpholine ppb Ammonia H2SO H2SO H2SO NaOH 0-15 NaOH HCl ppb HCl 0-18 HCl HNO HNO Uer defined 1 Uer defined 2

24 HAT Communication 24 SC450G eter eter TC SC2 [Method SC2: TC] [temp unit: ッ -C] [temp unit: ッ -F] / ッ -C ッ -F Calib. Setting Air adjut limit S CC hi lim CC lo lim 8 Stab time 2 to 30 Cal interval 1 to 250 d Concentration Additional table [Meaure: Conc only] Diable Enable Conc table unit [Meaure: Conc only] ppt ppm ppb Output etup ma1 etup Type Control Output Simulate [Type: ] P PI PID CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] PID SP S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m :

25 HAT Communication 25 SC450G eter eter PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Burn [Type: Output] [Type: Output] Lin 0 [Type: Output (: Linear)] Lin 100 [Type: Output (: Linear)] Burn [Type: Output] Damping time [Type: Output] direct revere Low 180 Linear Table CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] Low 360 S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m :

26 HAT Communication 26 SC450G eter eter [Type: Simulate] Simulate [Type: Simulate] ma2 etup Type Control Output Simulate [Type: ] PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID) ] PID D time [Type: Control (: PID)] Burn P PI PID CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] direct revere Low 180 S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m :

27 HAT Communication 27 SC450G eter eter [Type: Output] [Type: Output] Lin 0 [Type: Output (: Linear)] Lin 100 [Type: Output (: Linear)] Burn [Type: Output] Damping time [Type: Output] [Type: Simulate] [Type: Simulate] Linear Table CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] Low 360 Simulate S1 etup Type Control Alarm Simulate HOLD USP [Type: ] P PI PID S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [: S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [:

28 HAT Communication 28 SC450G eter eter PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] direct revere PF DC Alarm S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : p/m

29 HAT Communication 29 SC450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] [Type: USP] CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] Low Hard + Soft Hard Only ON/ ON OFF HOLD USP USP afety margin Type Control Alarm Simulate HOLD [Type: ] S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : The ue of Built-in DTM diable Hard + Soft to be elected.

30 HAT Communication 30 SC450G eter eter PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID) ] PID D time [Type: Control (: PID)] Analog output Max freq [Type: Control (Analog output: PF)] DC time [Type: Control (Analog output: DC)] [Type: Alram] P PI PID CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] direct revere PF DC Alarm S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : p/m

31 HAT Communication 31 SC450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] Low Hard + Soft Hard Only ON/ ON OFF HOLD S3 etup Type Control Alarm Simulate HOLD [Type: ] P PI PID S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: O.cm, O.m [: ESIST1, 2] ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : The ue of Built-in DTM diable Hard + Soft to be elected.

32 HAT Communication 32 SC450G eter eter CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. PID SP PID ng PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] 360 PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12 p/m DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. Alarm Sp Alarm dir. Low Alarm hyt.

33 HAT Communication 33 SC450G eter eter Alarm delay [Type: ] Hard + Soft Hard Only The ue of Built-in DTM diable Hard + Soft to be elected. [Type: Simulate] ON/ Contact [Type: Simulate (: ON/OFF)] ON OFF [Type: Simulate (: percentage)] [Type: HOLD] HOLD S4 etup Type Control Alarm Simulate HOLD [Type: ] P PI PID CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. PID SP PID ng PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] 360 PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12

34 HAT Communication 34 SC450G eter eter DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm CONDUCT [Meaure: Cond only, Cond + Conc] ESIST1 [Meaure: re only] CONCENT1 [Meaure: Conc only] TEMPEATUE CONDUCT2 [Meaure: Cond only] ESIST2 [Meaure: re only] CONCENT2 [Meaure: Conc only] CONCENT [Meaure :Cond + Conc] eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. Alarm Sp Alarm dir. Low Alarm hyt. Alarm delay [Type: ] Hard + Soft Hard Only The ue of Built-in DTM diable Hard + Soft to be elected. Ue a device DTM or et at the front panel diplay. [Type: Simulate] ON/ Contact [Type: Simulate (: ON/OFF)] ON OFF [Type: Simulate (: percentage)] [Type: HOLD] HOLD HOLD etup HOLD L/F Lat Fixed ma1 Fixed [HOLD L/F: Fixed] to ma ma2 Fixed [HOLD L/F: Fixed] to ma HOLD during cal diabled enabled Error config Cond too high [Meaure: Cond only, Conc only]

35 HAT Communication 35 SC450G eter eter e too low [Meaure: e only] SC hi lim [Meaure: Cond only, Conc only] S e low lim [Meaure: e only] ohm Cond too low [Meaure: Cond only, Conc only] e too high [Meaure: e only] SC lo lim [Meaure: Cond only, Conc only] S e hi lim [Meaure: e only] ohm Temp too high Temp too low Pol detected Cal time exc USP limit exc 1t comp mtrx 2nd comp mtrx Conc table Logbook config Senor logbook Error on Error off Temp Coeff. Air adjut limit Adj CC lo lim Adj CC hi lim eference temp Stab. Time ma logbook ma etup Hold fixed value PID etpoint PID range Manual reet PID I time PID D time Burn Linear Damping time

36 HAT Communication 36 SC450G eter eter Contact logbook Contact etup PID etpoint PID range Manual reet PID I time PID D time Control type DC period time Max pule freq. Alarm etpoint Alarm direction Alarm hyterei Alarm delay time Erae logbook Calibration Senor Predictive Maint. All logbook logbook full No Ye Baic etup Tag Alphanumeric value Ditributor Model Device information Decriptor Alphanumeric value Meage Alphanumeric value Poll addr 0 to 15 Num rep pream 0 to 255 eview Model Ditributor Write protect Manufacturer Dev id Tag Decriptor Meage Date Univeral rev Fld dev rev Software rev Poll addr Num rep pream The ue of Built-in DTM diable the etting properly. The ue of Built-in DTM diable the etting properly. : The ue of Built-in DTM may make character diplayed a unintended one. ºC i replaced with ッ -C, ºF i replaced with ッ -F. Ue a device DTM or check at the front panel diplay. DD Online eter for ISC450G (Device reviion 2, DD file reviion 2) CAUTION Ue a device DTM or the front panel diplay to perform etting/checking. Built-in DTM may replace character with unintended one or diable etting appropriately. that ºC i diplayed a ッ-C, ºF i diplayed a ッ-F.

37 HAT Communication 37 In the following lit, thoe item with bracket [ ] or [()] are valid when the parameter are et a decribed in thoe bracket. ISC450G eter eter Proce PV S/cm, S/m [Meaure: Cond ppb [Meaure: Conc only] Zoom SV ッ -C ッ -F TV S/cm, S/m [Meaure: Cond ppb [Meaure: Conc only] Zoom enor Fact CC /cm, /m Adj CC /cm, /m Method SC1 Method SC2 Ohm ohm Zoom output Ohm ohm ma1 value ma ma2 value ma S1 perc S2 perc S3 perc S4 perc Zoom device Serial number Software eviion Device eviion Logbook Calibration Commiioning Input contact Diable Factor 10 ma1 Factor 10 ma2 Factor 10 ma1+2 Meaurement etup Meaure Cond only Cond+Conc Con conly Configure enor Mea unit /cm /m Fact CC to 5 [Mea unit: /cm] [Mea unit: /m] Temp etting Temp enor Pt1000 NTC30k Temp unit ッ -C ッ -F /cm, /m The ue of Built-in DTM diable Factor 10 ma1+2 to be elected. The ue of Built-in DTM diable Cond and Conc to be elected. Temp compenation Temp comp Auto Manual

38 HAT Communication 38 ISC450G eter eter Temp compenation Man value [temp unit: ッ -C] to [temp unit: ッ -F] ッ -C ッ -F ef temp [temp unit: ッ -C] to [temp unit: ッ -F] ッ -C ッ -F Method SC1 None TC Nacl Matrix Matrix SC1 [Method SC1: Matrix] Sulfuric acid 1..5 Sulfuric acid Sulfuric acid Sulfuric acid HCl 1..5 HCl HCl HNO HNO HNO NaOH 1..5 NaOH NaOH Uer defined 1 Uer defined 2 TC SC1 [Method SC1:TC] (Temp unit: ッ -C) (Temp unit: ッ -F) / ッ -C / ッ -F Method SC2 [Meaure: Cond only, Conc only] None TC Nacl Matrix Matrix SC2 [Meaure: Cond only, Conc only (Method SC2: Matrix)] Sulfuric acid 1..5 Sulfuric acid Sulfuric acid Sulfuric acid HCl 1..5 HCl HCl HNO HNO HNO NaOH 1..5 NaOH NaOH Uer defined 1 Uer defined 2 TC SC2 [Method SC2: TC] [temp unit: ッ -C] [temp unit: ッ -F] / ッ -C / ッ -F Calib. Setting Air adjut limit S CC high lim 10 12

39 HAT Communication 39 ISC450G eter eter CC low lim 8 Stabilization time 2 to 30 Calb interval 1 to 250 d Concentration Additional table [Meaure: Conc only] Diable Enable Conc table unit [Meaure: Conc only] ppt ppm ppb Output etup ma1 etup Type Control Output Simulate [Type: ] P PI PID CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc PID SP S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : PID ng S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] 360 PID D time [Type: Control (: PID)] 6

40 HAT Communication 40 ISC450G eter eter Burn Low 180 [Type: Output] Linear Table [Type: Output] CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc Lin 0 [Type: Output (: Linear)] S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : Lin 100 [Type: Output (: Linear)] S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : Burn [Type: Output] Low Damping time [Type: Output] 360 [Type: Simulate] Simulate [Type: Simulate] ma2 etup Type Control Output Simulate [Type: ] P PI PID

41 HAT Communication 41 ISC450G eter eter PID SP PID ng PID Dir PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] PID D time [Type: Control (: PID)] Burn [Type: Output] [Type: Output] CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc direct revere Low 180 Linear Table CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m :

42 HAT Communication 42 ISC450G eter eter Lin 0 [Type: Output (: Linear)] S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : Lin 100 [Type: Output (: Linear)] S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : Burn [Type: Output] Low Damping time [Type: Output] 360 [Type: Simulate] Simulate [Type: Simulate] S1 etup Type Control Alarm Simulate HOLD [Type: ] P PI PID CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc PID SP PID ng PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] 360

43 HAT Communication 43 ISC450G eter eter PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12 DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc Alarm Sp Alarm dir. Low Alarm hyt. Alarm delay [Type: ] Hard + Soft Hard Only The ue of Built-in DTM diable Hard + Soft to be elected. [Type: Simulate] ON/ Contact [Type: Simulate (: ON/OFF)] ON OFF [Type: Simulate (: percentage)] [Type: HOLD] HOLD contact S2 etup Type Control Alarm Simulate HOLD [Type: ]

44 HAT Communication 44 ISC450G eter eter P PI PID CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc PID SP S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : PID ng S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [ P a r a m : PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID] 360 PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12 p/m DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm

45 HAT Communication 45 ISC450G eter eter Alarm Sp Alarm dir. Alarm hyt. Alarm delay [Type: ] [Type: Simulate] Contact [Type: Simulate (: ON/OFF)] [Type: Simulate (: percentage)] [Type: HOLD] CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc Low Hard + Soft Hard Only ON/ ON OFF HOLD contact S3 etup Type Control Alarm Simulate HOLD [Type: ] P PI PID S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [: S/cm, S/m [: ppb [: ッ -C, ッ -F [: TEMPEATUE] [: The ue of Built-in DTM diable Hard + Soft to be elected.

46 HAT Communication 46 ISC450G eter eter CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. PID SP PID ng PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID) ] 360 PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12 p/m DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. Alarm Sp Alarm dir. Low Alarm hyt.

47 HAT Communication 47 ISC450G eter eter Alarm delay [Type: ] Hard + Soft Hard Only The ue of Built-in DTM diable Hard + Soft to be elected. [Type: Simulate] ON/ Contact [Type: Simulate (: ON/OFF)] ON OFF [Type: Simulate (: percentage)] [Type: HOLD] HOLD contact S4 etup Type Control Alarm Simulate HOLD [Type: ] [Type: Cntrol] P PI PID CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. PID SP PID ng PID Dir direct revere PID M [Type: Control (: P)] PID I time [Type: Control (: PI, PID)] 360 PID D time [Type: Control (: PID)] 6 Analog output PF DC Max freq [Type: Control (Analog output: PF)] 12

48 HAT Communication 48 ISC450G eter eter DC time [Type: Control (Analog output: DC)] [Type: Alram] Alarm CONDUCT [Meaure: Cond Only, Cond + Conc] CONCENT1 [Meaure: Conc TEMPEATUE CONCENT [Meaure: Cond + Conc] CONDUCT2 [Meaure: Cond CONCENT2 [Meaure: Conc eter can be written but cannot be read correctly. Write the parameter at the front panel diplay. Alarm Sp Alarm dir. Low Alarm hyt. Alarm delay [Type: ] Hard + Soft Hard Only The ue of Built-in DTM diable Hard + Soft to be elected. [Type: Simulate] ON/ Contact [Type: Simulate (: ON/OFF)] ON OFF [Type: Simulate (: percentage)] [Type: HOLD] HOLD contact HOLD etup HOLD L/F Lat Fixed ma1 Fixed [HOLD L/F: Fixed] to ma ma2 Fixed [HOLD L/F: Fixed] to ma HOLD during cal diabled enabled Error config Cond too high SC hi lim to S

49 HAT Communication 49 ISC450G eter eter Cond too low SC Lo lim Temp too high Temp too low Cal time exc 1t comp mtrx 2nd comp mtrx Conc table Logbook config Senor logbook Error on Error off Temp Coeff. Air adjut limit Adj CC lo lim Adj CC hi lim eference temp Stab. Time ma logbook ma etup Hold fixed value PID etpoint PID range Manual reet PID I time PID D time Burn Linear Damping time Contact logbook Contact etup PID etpoint PID range Manual reet PID I time PID D time Control type DC period time Max pule freq. Alarm etpoint Alarm direction Alarm hyterei Alarm delay time Erae logbook Calibration Senor All logbook logbook full No Ye Baic etup Tag Alphanumeric Ditributor Model Device information Decriptor Alphanumeric Meage Alphanumeric Poll addr 0 to 15 S Multiple checkbox allow more than one option to be elected. Multiple checkbox allow more than one option to be elected Multiple checkbox allow more than one option to be elected A confirmation meage appear before deleting. A confirmation meage appear before deleting. The ue of Built-in DTM diable the etting properly.

50 HAT Communication 50 ISC450G eter eter Num rep pream 0 to 255 eview Model Ditributor Write protect Manufacturer Dev id Tag Decriptor Meage Date Univeral rev Fld dev rev Software rev Poll addr Num rep pream The ue of Built-in DTM diable the etting properly. : Built-in DTM may replace character with unintended one or diable etting appropriately. ºC i replaced with ッ -C, ºF i replaced with ッ -F. Ue a device DTM or check at the front panel diplay.

51 eviion Information 51 Title : PH450G/SC450G/ISC450G ph/op/conductivity Converter HAT Communication Manual number : Sep. 2017/1t Edition Newly publihed For further information viit Yokogawa webite. Yokogawa Electric Corporation Nakacho, Muahino-hi, Tokyo , JAPAN Printed by KOHOKU PUBLISHING & PINTING INC.