WEATHER ALARM WR. Installation Manual
|
|
- Loraine Cain
- 5 years ago
- Views:
Transcription
1 WEATHER ALARM WR Installation Manual BARTLETT Instrument Co Ave. H Fort Madison, IA /22/18 1
2 INSTALLATION OVERVIEW The main function of the Weather Alarm is to alert a greenhouse controller that the weather conditions require the roof vent to be closed. The Weather Alarm can also report to the Bartlett Instrument Company Computer Interface System (CIS) program for weather monitoring and control. This installation manual will cover the general installation of the Weather Alarm and the specific connections to the Bartlett Instrument Company RWL Natural Ventilation Controllers and GHK Greenhouse Environmental Controllers. RWL NATRAL VENTILATION CONTROLLER TO BE CONTROLLED ANEMOMETER WEATHER ALARM WR JNCTION BOX RAIN SENSOR PLG-IN TRANSFORMER TEMPERATRE SENSOR (OPTIONAL) HMIDITY SENSOR (OPTIONAL) A typical installation consists of Weather Alarm WR, plug-in transformer, sensor junction box, anemometer and rain sensor. Optional temperature and humidity sensors can also be connected to the Weather Alarm WR. 2/22/18 2
3 BE SRE ALL POWER IS OFF BEFORE INSTALLATION! INSTALLATION SHOLD BE DONE BY A LICENSED ELECTRICIAN. BE SRE ALL WIRING AND EQIPMENT IS INSTALLED ACCORDING TO LOCAL ELECTRICAL CODES. THE WEATHER ALARM WR IS A LOW VOLTAGE DEVICE. LIMITED TO 24V AC CONTROL VOLTAGES. CATION: The Weather Alarm WR is designed to be reliable but as with all equipment, failures do occur. Therefore, in situations where loss could result from the failure of the Weather Alarm WR, separate backup thermostat or alarm systems should be provided. The reliability and performance of the Weather Alarm WR can be compromised by locating the controller in direct sunlight or in direct water spray. We also recommend when installing the WR Alarm to wire according to the diagram on page 11 to protect from lightning strikes and power surges. 2/22/18 3
4 PLACEMENT AND MONTING Mount the Weather Alarm WR in an easily accessible location. sually close to the RWL Natural Ventilation Controller or GHK Greenhouse Environmental Controller. Protect the Weather Alarm WR from direct sunlight for better reliability and readability. Moisture can cause corrosion and premature failure, so avoid direct water and have all wires enter and leave through liquid-tight connectors, waterproof conduit, or seal the wires with silicone sealant. WARNING: Some sealants release acetic acid while curing. Be sure sealant is completely cured (up to 3 days) before closing control box to avoid corrosion damage. To mount the Weather Alarm WR, remove the front cover and unplug ribbon cable from the relay board. Insert the 4 self-drilling screws provided with the Weather Alarm WR through the 4 screw-hole knockouts and fasten the box to the wall. Cover the screw heads with plastic cups provided. After all wiring is complete and any sealant cured, reattach the ribbon cable and screw on the front cover. Alternately, the Weather Alarm WR may be mounted with drywall screws placed through the corner holes of the box. TOP Weather Alarm WR PCB SCREWHOLE KNOCKOTS 2/22/18 4
5 RAIN SENSOR The rain sensor detects moisture on the surface of the sensor. It does not measure the amount of moisture that has fallen. The Weather Alarm WR junction box has one rain sensor input labeled RS. When the Weather Alarm WR detects moisture on the rain sensor the Weather Alarm WR turns on a rain sensor heater to quickly dry off the surface of the rain sensor after the rain has stopped. The Weather Alarm WR junction box has one rain sensor heater input labeled RSH. To ensure proper readings, the rain sensor should be mounted in a location that will not be sheltered from rain from any direction. Mount the sensor at a 10 degree angle to keep water from pooling on the sensor surface. Also, the sensor should be mounted in an easily accessible location in order to clean any debris from the sensor surface. The rain sensor comes with 6 leads to connect the rain sensor and 6 leads to connect the rain sensor heater to the four terminals of the junction box. The white/black twisted pair connect to rain sensor. The red/black twisted pair connect to the rain sensor heater. ANEMOMETER For anemometer mounting instructions please refer to WS B manual. TEMPERATRE SENSOR The optional thermistor is the temperature sensor. The Weather Alarm WR junction box has one thermistor input labeled TH. To ensure proper readings, the thermistor should not be in direct sunlight or where it will be sprayed with water. The thermistors come with 24 leads and can be connected directly to the two terminals labeled TH. There is no special orientation to the thermistor leads. 2/22/18 5
6 HMIDITY SENSOR The optional humidity sensor should be mounted in any location that it is necessary to measure humidity levels. The Weather Alarm WR junction box has terminals marked Hum In, Hum Power and Hum GND. To ensure proper readings, the humidity sensor should not be in direct sunlight or where it will be sprayed with water. WEATHER ALARM WR OTPTS The Weather Alarm has three alarm outputs wind alarm, rain alarm, and wind or rain alarm. The wind and rain outputs activate separately based on individual sensors. The wind or rain output activates when either sensor exceeds its set point. The wind alarm, rain alarm and wind or rain alarm are dry contacts to directly connect to a RWL Natural Ventilation Controller or GHK Greenhouse Environmental Controller. It is possible to source 24 V AC to drive a relay by using a jumper wire to connect terminal 1 to terminal 22 see diagram CONNECTING MLTIPLE CONTROLLERS, ISOLATED. 2/22/18 6
7 CONNECTION LOCATIONS THERMISTOR RAIN SENSOR NSED WIND OR RAIN ALARM RAIN ALARM NSED HMIDITY PROBE RAIN SENSOR HEATER NSED L L 1 2 W I N D A L A R M N S E D N S E D N S E D N S E D TERMINAL DESCRIPTION TERMINAL DESCRIPTION TERMINAL DESCRIPTION 1 24VAC L VAC L2 COM WIND ALARM 15 RAIN SENSOR HEATER 27 THERMISTOR 4 WIND ALARM 16 RAIN SENSOR HEATER 28 THERMISTOR RAIN SENSOR RAIN SENSOR 7 19 RAIN ALARM RAIN ALARM WIND OR RAIN ALARM 33 HM. IN WIND OR RAIN ALARM 34 HM. POWER HM. GROND /22/18 7
8 2/22/18 8
9 2/22/18 9
10 ONLY IF YO HAVE ONE CONTROLLER TO WIRE TO WEATHER ALARM NIT 2/22/18 10
11 WIRING MLTIPLE CONTROLLERS TO WEATHER ALARM NIT 2/22/18 11
SSC-1D installation guide
Phason The Single Stage Control (SSC-1D) automatically controls the temperature in a room by switching fans, lamps, or heaters on or off as the temperature drops below or exceeds the temperature set point.
More informationInstallation Guide IM 1248
Installation Guide IM 1248 BACnet Thermostat for Heat Pump Units Group: Controls Part Number: IM 1248 Date: August 2015 Table of Contents Installation Guide Heat Pump.... 2 Applicable Models... 2 Mounting
More informationRH & T Sensors & Humidistats. RH-DT Duct Mount RH & T Sensors. Description
RH & T Sensors & Humidistats RH-DT Duct Mount RH & T Sensors Description RH-DT Duct Mount RH & T Sensors The RH-DT Duct Mounted Humidity and Temperature Sensors offer the latest technology for high accuracy
More informationECC-1 user manual and installation guide
ECC-1 user manual and installation guide Table of contents Introducing the ECC-1...1 Features...2 Optional accessories...2 About the manual...3 Using the buttons...3 About the status LEDs...4 Using
More informationDuct and Rough Service Carbon Monoxide Sensor
Product Identification and Overview Duct and Rough Service Carbon Monoxide Sensor BAPI s Carbon Monoxide Sensor offers enhanced electrochemical sensing with outstanding accuracy at low concentrations.
More informationMODEL FTGF2P (240 VAC)
SUMMARY MODEL FTGF2P (240 VAC) OPTIONS SELECTION At the back of the thermostat, there are two selection switches to set yor preference. 1 2 Temperatre in C or F. Time in 12 or 24 hors. TO SET TIME AND
More informationUser s Manual. For the SHORE POWER CONNECTION MONITOR MODEL 9151
User s Manual For the SHORE POWER CONNECTION MONITOR MODEL 9151 Table of Contents: Product Description... 3 Installation... 4 Optional Remote Alarm Installation... 7 Operator Test... 8 Alarms... 9 Figures...
More informationSeries. Access Power Controllers. Installation Guide
Series Access Power Controllers Installation Guide Models Include: Maxim11 - Power Supply 1: 12VDC @ 3.5 amp or 24VDC @ 2.7 amp. - Power Supply 2: 12VDC @ 3.5 amp or 24VDC @ 2.7 amp. - Sixteen (16) fuse
More informationLightning Warning System: LWS MK-II. User's Guide. KOREA EMI Technologies Co.,Ltd , Jangam-ri, Majang-myeon, Icheon-si, Gyeonggi-do, Korea
User's Guide CONTENTS FEATURES WHAT YOU NEED TO GET STARTED INSTALLATION DETAILS Installing the Antenna Installing the External Alert Siren The main console OPERATING PROCEDURE Power On Routine Push Buttons
More informationDRAFT INSTALLATION INSTRUCTIONS. Solid-State Series !! NOTE!! Covers the following models: Refer to INSERT for additional information
INSTALLATION INSTRUCTIONS Solid-State Series!! NOTE!! Covers the following models: " CS6100 - CS7100 " CS6200 - CS9200 " CS6220 - CS9220 " CS6230 - CS9230 " CS6500 - CS7500 " CS6330 - CS9300 " CS9400 -
More informationE340 BOILER CONTROL INSTALLATION MANUAL
E-3451 JUNE 1999 E340 BOILER CONTROL INSTALLATION MANUAL DESCRIPTION The E340 Boiler Room Control is a microprocessor-based Boiler Management System designed to interface with existing Fireye D Series
More informationRev 4 12-APR IRLDS II and IRLDS II User Interface Installation and Operation Manual
026-1305 Rev 4 12-APR-2010 IRLDS II and IRLDS II User Interface Installation and Operation Manual 1640 Airport Road, Suite 104 Kennesaw, GA 31044 Phone: 770-425-2724 Fax: 770-425-9319 ALL RIGHTS RESERVED
More informationType 300 Series Bench Electrode Stabilization Ovens
REPAIR PARTS INSTALLATION INSTRUCTIONS Type 300 Series Bench Electrode Stabilization Ovens *Please read all instructions, paying special attention to all cautions or warnings, before beginning any repairs.
More informationPROTEUS Series OEL8000III-K. Tank Gauging System. Installation Manual
OMNTEC PROTEUS Series OEL8000III-K Tank Gauging System Installation Manual Page 1 of 23 PROPRIETARY INFORMATION NOTICE This document contains information and material developed by OMNTEC Mfg., Inc. All
More informationColibri. Automatic Tank Gauge CL6 Series Installation Guide
Colibri Automatic Tank Gauge CL6 Series Installation Guide Manual # Revision Date Changes from Previous Revision 000-2153 C Jan. 2013 Pipe compound brand change, Updated Control drawing. Franklin Fueling
More informationPre-March 2016 Design - Click to be redirected to newer SBS-H2 design SBS-H2. Hydrogen Gas Detector Kit
Pre-March 2016 Design - Click to be redirected to newer SBS-H2 design N56 W16665 Ridgewood Drive Menomonee Falls, WI 53051 SBS-H2 Hydrogen Gas Detector Kit For battery charging rooms and other areas where
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Electric Heat Sections Used with Blower Coil Units ELECTRIC HEAT SECTIONS 505,084M (0655012-30) 05/15 Supersedes 09/11 Litho U.S.A. NOTICE TO INSTALLER IT IS HIGHLY RECOMMENDED
More informationSnifter ATEX22 VERSION. User Manual. Distributor
Snifter ATEX22 VERSION User Manual Distributor Version 1.4 09/09/2009 Table of Contents 1. INTRODUCTION... 3 1.1. Safety... 3 1.2. Product overview... 4 1.3. How does it work?... 4 2. INSTALLATION... 5
More informationMSC Natural zones with Poly-vent Curtain. Configuration#:20MF23V7
MSC-20 2 Natural zones with Poly-vent Curtain Configuration#:20MF23V7 Input/Output Table: Inputs Qty Outputs Qty Inside Temperature 2 Variable Speed Stage 2 On/Off Stage 2 Natural Poly-vent Curtain 4 Cooling
More informationGHK12X2 GREENHOUSE CONTROLLER. Operation Manual
GHK12X2 GREENHOUSE CONTROLLER Operation Manual BARTLETT Instrument Co. 1032 Avenue H Fort Madison, IA 52627 319-372-8366 www.bartinst.com Revised: 1/30/15 2 Front Panel Description... 3 Introductory Notes...
More informationGreentrol Automation, Inc.
Model GA-100 Technical Manual GreenAlert 100 Series Greentrol Automation, Inc. Installation, Operation and Maintenance Technical Manual GA-100 Document Name: TM_GA-100_R1C TM_GA-100_R1C Part Number: 960--0000
More informationGPF Dimming Panels. GRAFIK Systems SPECIFICATION SUBMITTAL
DESCRIPTION Controls all Lutron 3-Wire Fluorescent Dimming Ballasts (Hi-Lume, ECO-0, and Compact SE). Provide power and dimming for up to 4 fluorescent circuits. Models available for: 0V: 8 to 4 circuits.
More informationTRUERH Series HE-67xx Humidity Element with Temperature Sensor
Installation Instructions HE-67xx Issue Date 0501 TRUERH Series HE-67xx Humidity Element with Temperature Sensor Installation IMPORTANT: The HE-67xx Series Humidity Element with Temperature Sensor is designed
More information10-175UL INSTALLATION. Power Supply UL. Access Control Power Supply/Charger. Installation and Specifications Manual
INSTALLATION 10-175UL Power Supply 10-175UL Access Control Power Supply/Charger Installation and Specifications Manual Overview The 10-175UL is a power limited power supply/charger that will convert 115VAC
More informationTABLE B Remote Wire Connection
AQUAS POOL PACKAGE INSTALLATION INSTRUCTIONS FOR MODELS: XPN 1.0, 1.3 and 1.5 AQUAS Pool Package The AQUAS pool package system is a high efficiency commercial condensing boiler package system pre-piped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS The SensorNet I/O Module provides attachment for up to 32 alarms and up to 16 switched devices. An RS-232 or RS-422 communications port is also provided for receiving serial alarms.
More informationECC-1 user manual and installation guide
ECC-1 user manual and installation guide Table of contents Introducing the ECC-1...1 Features...2 Electrical ratings...2 Optional accessories...3 About this manual...3 Using the buttons...4 About the status
More informationOperator: Save these instructions for future use!
50A65-843 Universal Integrated Furnace Control INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING
More informationAQUAS POOL PACKAGE INSTALLATION INSTRUCTIONS FOR MODELS: AP AQUAS Pool Package
100285340_2000542910_Rev A AQUAS POOL PACKAGE INSTALLATION INSTRUCTIONS FOR MODELS: AP 400-850 AQUAS Pool Package The AQUAS pool package system is a high efficiency commercial condensing boiler, pre-piped
More information21-light Remote Annunciator. Owner s Manual
21-light Remote Annunciator Owner s Manual Annunciator Description... Inside Font Cover Detailed Specifications... 1 Environmental Specifications... 1 Power Supply Requirements... 1 Communication With
More informationRack Mount Series Installation Guide
Rack Mount Series Installation Guide Models Include: Maximal1RHV Maximal1RV - 12VDC @ 4 amp or 24VDC @ 3 amp. - 12VDC @ 4 amp or 24VDC @ 3 amp. - Eight (8) Fuse Protected Outputs. - Sixteen (16) Fuse Protected
More informationWD-CS. Water leak detection cable. Technical Overview. Features. Page 1. Data Sheet Ref: Issue: 5.1.
Data Sheet Ref: 90501085 WD-CS Water leak detection cable Technical Overview The WD-CS range of cable sensors are typically used to detect water leaks usually under floors, and are used in conjunction
More informationOWNER S MANUAL. Vintage Signature Series models: AC750, AC1050, AC1100, AC1250, AC1500, AC1750. Proudly Made in the USA.
OWNER S MANUAL Vintage Signature Series models: AC750, AC1050, AC1100, AC1250, AC1500, AC1750 Proudly Made in the USA support@aquacomfort.com 888-475-7443 Manufacturing High Quality, High Efficiency Heat
More informationINSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP
INSTALLATION INSTRUCTIONS FOR 6532 SERIES PACKAGE HEAT PUMP RV Products A Division of Airxcel, Inc. P.O. Box 4020 Wichita, KS 67204 1976-360 (1-02) PP TABLE OF CONTENTS 1. Warnings......................................................
More informationInstallation Guide for models:
140 58th St. Brooklyn, NY Access Power Controllers with Power Supplies Installation Guide for models: Maximal3FD - 12VDC @ 4.6 amp or 24VDC @ 5.2 amp. - Sixteen (16) PTC protected power-limited outputs.
More informationecolor Graze Powercore Linear LED surface light for wall washing and grazing
Linear LED surface light for wall washing and grazing Linear LED surface light for wall washing and grazing linear LED lighting fixtures are ideal for surface grazing and wall-washing applications that
More informationInstallation and Owner Man u al
T H R E E P H A S E Evaporator Fan Control System Installation and Owner Man u al WARNING The installation of this device should be done only by competent personnel, experienced in electrical wiring, and
More informationINSTALLATION & USER MANUAL
INSTALLATION & USER MANUAL HC Digital Automatic Humidistat (Y3760) CONTROLS 506808-01 3/2016 Supersedes 6/2011 picture goes here THIS MANUAL MUST BE LEFT WITH THE HOMEOWNER FOR FUTURE REFERENCE NOTICE
More informationThree Ventilation Stage Control. TVS user manual
Three Ventilation Stage Control TVS user manual 2003, Phason Inc. All rights reserved. Printed in Canada. 102455 Rev 04 2003-02-03 LIMITED WARRANTY This warranty applies only to the Automatic Environment
More informationIntensity Level. Intensity Control. Signal Type Switch. 12V Power Port. Signal Ports
Dimmer User Manual OVERVIEW The Fluence Dimmer can dim up to 50 fixtures over a total of 200 feet of signal wire via a 0-10V or PWM signal to provide uniform control of light intensity delivered to your
More informationPO Box 827 Hawley, MN (218) Fax (218)
Introduction Before proceeding with the installation or operation of the Oil Alert System, read all instructions thoroughly, as well as complying with all Federal, State and Local codes, Regulations and
More informationFAULT CODES. Included in this section are instructions to Reset the two Hot Tank Overload Devices (High Safety Limit).
FAULT CODES Fault Code Index 1. Blue Chilling LED Flashing Cold Sensor Fault 2. Red Heating LED Flashing Hot Sensor Fault 3. Green LED Flashing Filter Service Alert 4. All but Power Button LEDs Flashing
More informationPANEL_RS2. Run / Standby Panel. INSTALLATION MANUAL Version 1.02 MITSUBISHI ELECTRIC FOR INSTALLERS. Page 1 of 25
Run / Standby Panel PANEL_RS2 FOR INSTALLERS INSTALLATION MANUAL Version 1.02 For safe and correct use, please read this installation manual thoroughly before installing the PANEL_RS2. MITSUBISHI ELECTRIC
More informationTMC. Installation and Operation Manual TMC. Temperature and Pressure Monitoring for Heating and Cooling Applications. Temperature Monitoring Control
Installation and Operation Manual Temperature and Pressure Monitoring for Heating and Cooling Applications Temperature Monitoring Control VALVE OPEN ALARM System= 128 o F Alarm At= 130 o F RESET /BACK
More informationProduct Instructions. Hydronic Mixing Block Version Wiring Terminal Block Pressure/Temperature Sensor Delivery Fitting (3) Display Screen
Hydronic Mixing Block Version 1.104 The Hydronic Mixing Block is a mixing device and boiler control, with a built in circulator and system controller. The block can provide either a fixed or reset water
More informationTS-RA1, TS-RA2 and TS-RK Tank Overfill Alarms
TS-RA1, TS-RA2 and TS-RK Tank Overfill Alarms Installation Guide franklinfueling.com 3760 Marsh Rd. Madison, WI 53718, USA Tel: +1 608 838 8786 Fax: +1 608 838 6433 Tel: USA & Canada +1 800 225 9787 Tel:
More informationExternal Roof-mounted Power Vent System
External Roof-mounted Power Vent System Installation, Operation and Owner s Manual Please read this manual thoroughly before beginning the installation. It has information which is important for safe installation
More information5 Inch Speed Dome Installation Manual V2.0.0
5 Inch Speed Dome Installation Manual V2.0.0 2010-01 1 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to
More informationForever Flowering Greenhouse Suggested Setup Wiring Diagrams
Forever Flowering Greenhouse Suggested Setup Wiring Diagrams DANGER Electrocution Hazard! Ensure all power is disconnected before servicing or wiring. Install all electrical equipment and wiring in accordance
More informationInstallation Instructions
53DS --- 900 --- --- --- 092 Duct---Free Systems Accessory Power Ventilation Kit for In --- Ceiling Cassette Fan Coil Units Size 018 --- 036 Installation Instructions NOTE: Read and become familiar with
More informationALARM OUTPUT MODULE. Product #7736
ALARM OUTPUT MODULE The Alarm Output Module (AOM) enables you to use weather station alarms or commands from your computer to automatically start or stop external devices such as indicator lights, audio
More information4-Channel Contact Closure Fiber Link Card System
USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U-020 2017A-0330 4-Channel Contact Closure Fiber Link Card System SYSTEM INSTALLATION INFORMATION Description The 4 Channel
More informationSingle Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual
We manage heat MANUAL Single Point Freeze Protection Heat Trace Control TRACON MODEL FPT 130 Installation and Operation Manual 1850 N Sheridan Street South Bend, Indiana 46628 (574) 233-1202 or (800) 234-4239
More informationDaytime Fan-Aspirated Radiation Shield Kit Installation Manual
Daytime Fan-Aspirated Radiation Shield Kit Installation Manual For Vantage Pro2 & Vantage Pro2 Plus Stations Introduction The instructions describe how to upgrade a non-aspirated Vantage Pro2 radiation
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The PLT-BY Tee Splice Connection Kit is for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with any vendor s heater cables small
More informationElement. Controller. Manual for use and maintenance. Element. Climate Controller. Ag/MIS/UMGB /17 Rev 1.0 P/N:
Manual for use and maintenance Element Controller Element Climate Controller Ag/MIS/UMGB-2439-02/17 Rev 1.0 P/N: 110584 Element Manual for use and maintenance Original instructions This manual for use
More information50M56U-843 INSTALLER MUST READ DESCRIPTION PRECAUTIONS WARNING CAUTION
50M56U-843 Universal Single Stage HSI Integrated Furnace Control Kit INSTALLATION INSTRUCTIONS INSTALLER MUST READ PAGE 3 CONTAINS WIRING HARNESS AND BLOWER CONNECTION INSTRUCTIONS FOR ALL APPLICATIONS
More informationBeacon 410A Gas Monitor Operator s Manual
Beacon 410A Gas Monitor Operator s Manual Part Number: 71-0397 Revision: F Released: 12/5/17 www.rkiinstruments.com Product Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to be
More informationInstall Guide Customer Support: or Visit our website
Install Guide 8045 Customer Support: 888-515-2585 or Visit our website www.ritetemp-thermostats.com 312-014 Install Guide 8045 Caution To avoid electrical shock and to prevent damage heating system, and
More informationSafety & Installation Instructions
Model 8476 Thermostat with Event-Based Air Cleaning Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS Table of contents Installation Installation location recommendations... 3 Outdoor
More informationKT-100 Door Controller
WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully
More informationNGC-UIT2-ORD-R Remote User Interface Terminal for Raychem NGC Systems Installation Instructions
NG-UIT2-ORD-R Remote User Interface Terminal for Raychem NG Systems Installation Instructions Description The NG-UIT2-ORD-R is a wall-mounted display which allows the User Interface Terminal (UIT) to be
More informationPipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual
MANUAL Pipe Freeze Protection Control SCFP-CO-F130 Installation and Operation Manual Model FPT 130 Single Point Freeze Protection Heat Trace Control Table of Contents SCFP-CO-F130 Overview... 3 Installation...
More informationCoziStat. 1. Introduction and Brief Description COZISTAT INSTALLATION I NSTRUCTIONS &OPERATING MANUAL
COZISTAT INSTALLATION I NSTRUCTIONS &OPERATING MANUAL CoziStat 1. Introduction and Brief Description The CoziStat is an easy-to-use, programmable thermostat with digital display. CoziStat can be used with
More informationCAUTION WARNING. 50T Integrated Furnace Control INSTALLATION INSTRUCTIONS DESCRIPTION PRECAUTIONS
50T35-743 Integrated Furnace Control INSTALLATION INSTRUCTIONS FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY
More informationOperator: Save these instructions for future use!
50V64-743 Integrated Furnace Control for Furnaces with Variable Fan Speed INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
More informationACM8 Series UL Listed Sub-Assembly Access Power Controllers. Installation Guide. ACM8 - Eight (8) Fuse Protected Outputs
ACM8 Series UL Listed Sub-Assembly Access Power Controllers Installation Guide Models Include: ACM8 - Eight (8) Fuse Protected Outputs ACM8CB - Eight (8) PTC Protected Outputs Rev. 042811 More than just
More informationSCHWAN INSTALLATION GUIDE
1 SCHWAN INSTALLATION GUIDE For Schwan SC60 FOR SERVICE OR ASSISTANCE CALL MERQUIP ON 0800 636 0 636. Schwan recommends that a qualified tradesperson installs your Schwan system. 2 INFORMATION AND SAFETY
More informationThree Phase Simplex. Installation (937) Installation Instructions and Operation/Troubleshooting Manual. Installation of Floats.
Three Phase Simplex Installation Instructions and Operation/Troubleshooting Manual This control panel must be installed and serviced by a licensed electrician in accordance with the National Electric Code
More informationLoudspeakers Line Isolator System
Commnications Systems Lodspeakers Line Isolator System Lodspeakers Line Isolator System www.boschsecrity.com Provides redndant lodspeaker loops for pblic address and voice alarm systems Dramatically redces
More informationYSI Environmental YSI Operations Manual. Recirculating System Monitor
YSI Environmental P u r e D a t a f o r a H e a l t h y P l a n e t. YSI 5200 Recirculating System Monitor Operations Manual Table of Contents SECTION 1. SAFETY...3 1.1 GENERAL SAFETY INFORMATION...3
More informationHOT WATER BOTTLE BATH PART NUMBER
If you need any assistance or if you have questions about this item, call our Tech Help Line at (254) 848-4300. Do not use this product without filling it with water or immediate damage can result. All
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TM DishDrawer dishwasher DD36SDFTX (Designer) & DD36STI (Integrated) models US CA 59008D 04.3 a SAFETY AND WARNINGS Electrical hazard WARNING! Before installing the dishwasher,
More informationTHERMAL BUILDING SOLUTIONS EN-TraceTekTTSIM1A-IM-H /16
TraceTek TTSIM-1A TraceTek Sensor Interface Module with Relay Installation/OPERATION Instructions Approvals and Certifications TYPE NM General Signaling Equipment 76LJ Only AC versions are UL listed and
More informationEL-TSTAT-8820 Safety & Installation Instructions
EL-TSTAT-8820 Safety & Installation Instructions TABLE OF CONTENTS WI-FI SETUP Wi-Fi Setup 2 INSTALLATION Installation location recommendations 3 Outdoor temperature sensor (included) 3 Remote temperature
More information24 VAC SYSTEM CONTROL KIT
24 VAC SYSTEM CONTROL KIT Model: CK-43 Tubing MG1 Barometric Draft Control The CK-43 is designed for use with the SWG Series Power Venter for controlling Natural Gas and L.P. Gas Draft Induced appliances.
More informationDRAIN WATER TEMPERING INSTALL
! WARNING! CAUTION DRAIN WATER TEMPERING KIT - 0601-00-07-86 WARNING! This kit should be installed only by qualified service personnel to reduce the risk of electric shock, serious injury, or fire. A plumbing
More informationSafety & Installation Instructions
8400 Series Thermostats Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS 61000652C 8400 Tstat Install.indd 1 10/13/09 11:08:56 AM Table of contents Installation Installation location
More informationInstallation Guide for models:
140 58th St. Brooklyn, NY Access Power Controllers with Power Supplies Installation Guide for models: Maximal11F - Power Supply 1: 12VDC @ 3.3 amp or 24VDC @ 3.6 amp. - Power Supply 2: 12VDC @ 3.3 amp
More informationCMT MANUAL 6. NMC SENSORS
CMT MANUAL 6. NMC SENSORS TABLE OF CONTENTS INDEMNITY... 5 DOCUMENT INFORMATION... 5 ACKNOWLEDGEMENTS... 5 6.1 INTRODUCTION... 6 6.2 TEMPERATURE AND HUMIDITY SENSORS... 7 6.2.1. TEMPERATURE SENSOR... 7
More informationI/O ZONE 560/583 AND OPERATION MANUAL
UPM I I/O ZONE 560/583 INSTALLATION AND OPERATION MANUAL 1 UNIT PROTECTION MODULE HARDWARE OPERATION IMPORTANT: This manual is for UPM board part numbers 8733 800 259. See controller label as shown in
More informationTTSIM-1A. TraceTek Sensor Interface Module with Relay. Installation/Operation Instructions. Installation Items (not supplied) Tools Required.
TTSIM-1A TraceTek Sensor Interface Module with Relay Installation Items (not supplied) General Information Installation/Operation Instructions Please read these instructions and keep them in a safe place.
More informationInstall Guide 8046 ENGLISH. Customer Support: or: visit our website Printed in China ON.
. ON Install Guide 8046. ON ENGLISH Customer Support: 888-515-2585 or: visit our website www.ritetemp-thermostats.com Printed in China 1-405-049 Install Guide 8046 Caution To avoid electrical shock and
More informationRPSMLR2 RPSMLR2BB. Panic Device Power Controller Installation Guide LISTED. Rev
RPSMLR2 RPSMLR2BB Panic Device Power Controller Installation Guide LISTED Rev. 102715 Overview: RPSMLR2BB, RPSMLR2 will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed
More informationRetrofit Instructions CLEARVIEW DAY COVER CAUTION: Please read this manual completely before attempting to install, operate or service this equipment
Retrofit Instructions CLEARVIEW DAY COVER CAUTION: Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2019 Duke Manufacturing Co.
More informationGasScanner 4C. Four Channel Monitor. Operator s Manual. MINT-0280-XX Rev. A 02/25/08
GasScanner 4C Four Channel Monitor Operator s Manual MINT-0280-XX Rev. A 02/25/08 Product Warranty Matheson Tri-Gas., warrants gas alarm equipment sold by us to be free from defects in materials, workmanship,
More informationNeon LED Rope Light Installation Instructions
Neon LED Rope Light Installation Instructions 1 Specifications 12V (WW, CW, BL) 24V (WW, CW, BL) Beam angle (FWHM) 160 Power Consumption Luminous Flux (lm)* 2.44W/ft 85lm/ft Lifetime hours (70% light output)
More informationHeat Transfer Products, Inc. 120 Braley Road East Freetown, MA The first totally integrated multiple boiler management control.
Heat Transfer Products, Inc. 120 Braley Road East Freetown, MA 02717 The first totally integrated multiple boiler management control. USING THIS MANUAL USING THIS MANUAL A. INSTALLATION SEQUENCE Follow
More informationHigh Power Range Hood
High Power Range Hood Pictured Model: CW500 Installation and Operating Instructions Please read all instructions before installing and operating. All wiring and installation must be in accordance with
More informationDETCON MODEL AV1/AV2-C1D2M Hazardous Duty Class I. Div 2, Multitone Alarm Station
DETCON MODEL AV1/AV2-C1D2M Hazardous Duty Class I. Div 2, Multitone Alarm Station Operator s Installation and Instruction Manual DETCON, Inc. 3200 Research Forest Dr, The Woodlands, Texas 77387 Ph.281.367.4100
More information24 VAC SYSTEM CONTROL KIT
24 VAC SYSTEM CONTROL KIT Model: CK-91F and CK-91FG Designed for use with the SWG Series Power Venter for controlling Natural Gas or L.P. Gas draft induced appliances with a 24 VAC Gas Valve and a 30-millivolt
More informationBeacon 200 Gas Monitor Operator s Manual. Part Number: RK Released: 6/6/08
Beacon 200 Gas Monitor Operator s Manual Part Number: 71-2102RK Released: 6/6/08 Table of Contents Chapter 1: Introduction.................................................3 Overview.............................................................3
More informationCabinet Cooler Systems
Cooler Systems Cooler Systems Stop electronic control downtime due to heat, dirt, and moisture! maintain NEMA 4, 4X, and 12 integrity. All are and compliant! What is an EXAIR Cooler System? A low cost,
More informationInstallation and Operation Manual CLEARVIEW DAY COVER CAUTION: To view a video scan the QR code above
Installation and Operation Manual CLEARVIEW DAY COVER To view a video scan the QR code above CAUTION: Please read this manual completely before attempting to install, operate or service this equipment
More informationSafety & Installation Instructions
8400 Series Thermostats Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS 61000652A 8400 Tstat Install.indd 1 7/23/09 2:20:45 PM Table of contents Installation Installation location recommendations...
More informationUser manual and installation guide
User manual and installation guide 31046005 Copyright Phason Inc. All rights reserved. Printed in Canada About the manual The manual describes the features of your control and how to use them; it does
More informationInstallation Instructions DTC-24 SNOw MELTING &
Installation Instructions SNOw MELTING & ROOF DE-ICING controls R Roof and Gutter De-icing or Snow Melting Control S Roof and Gutter De-icing or Snow Melting Control Contents page Section 1. Overview 1.1
More informationACSI Series 1550K-MD and 1550-MD Motor Drive Electric Latch Retraction
ACSI Series 1550K-MD and 1550-MD Motor Drive Electric Latch Retraction Riser and Point-to-Point Drawings for Standard Access Control Applications Using Maintained Latch Retraction Control or Momentary
More informationAL400ULACM AL600ULACM - 4 amp - 12VDC or 6 amp. - Fused Outputs - Fused Outputs
ACM Series Access Power Controllers with Power Supplies Installation Guide Models Include: AL400ULACM AL600ULACM - 12VDC @ 4 amp - 12VDC or 24VDC @ 6 amp. or 24VDC @ 3 amp - Fused Outputs - Fused Outputs
More informationINSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY
INSTALLATION INSTRUCTIONS FOR 7330C740 FLUSH MOUNT CEILING ASSEMBLY TABLE OF CONTENTS Warnings...3 Package Contents...3 General Information...3 Supply Ducting And Registers...3 Routing 115 VAC Wiring...5
More information