Power Line Carrier technology

Transcription

1 Power Line Carrier technology To be used in new or renovated traditional installation (L+ required) up to 00 m SIMPLE TO ISTLL FOR MXIMUM COMFORT PLC technology, which systematically includes neutral, is a control solution for managing functions such as lighting, roller blinds and heating. It can be used to control functions individually or by creating scenarios, or even remotely (via the Internet) using the IP xiophone. ll the functions can be combined with safety and communication solutions. WIRIG DIGRM PLC transmitter IR receiver switch PLC transmitter/ receiver switch IR mobile scenario controller 440

2 LOCL COTROL GEERL COTROL UTOMTIC SWITCH (See p. 44) Controls and times the lighting each time someone passes MOBILE DIMMER SWITCHED SOCKET (See p. 59) Controls the lighting from the socket CETRLIZED ROLLER BLIDS COTROL (See p. 444) Controls all the blinds in one single action SCERIO COTROLLER WITH TOUCH SCREE (See p. 55) Manual or automatic scenario control 0 V C Motor Scenario Switch B C B C B C LEarth B B C Indicates lighting control Indicates lighting control via sockets Indicates roller blinds control REMOTE COTROL MOBILE SCERIO COTROL MEDI SERVER (See p. 445) Controls : 0 scenarios, broadcasting Hi-Fi channels, home cinema, etc... IP XIOPHOE (See p. 445) Controls the electrical functions of the home remotely via the Internet MOBILE SCERIO SWITCH (See p. 44) Can control up to 6 scenarios from any chosen location REMOTE COTROL SCERIO COTROLLER (See p. 44) Controls the whole electrical installation. Up to 4 scenarios plus TV RGES ICORPORTIG PLC TECHOLOGY Céliane See p Galea Life See p See p See p

3 PLC lighting control power line carrier technology with Céliane TM range EW 67 5 (Oxidised Iron) (Wenge Coloured) Cover plates, plates and supports selection chart (p. 549 to 565) Particularly suitable for new buildings and heavy renovation Can be installed in living areas, reception areas, working areas (stores, restaurants, medical centres...) Can be controlled by IR from the same room or by PLC with lighting scenarios controller or other scenario controllers (p. 54, 55) 0-0 V - 50/60Hz Pack Cat.os Dimmer switches Pack Cat.os Switches 44 Switch for on/off/dimming control of the circuit connected to the terminals With factory-set lighting levels accessed using the + and - buttons The transmitter function is used for on/off/dimming control of other light switches in the installation The receiver function is used to execute on/off/ dimming commands received from lighting scenarios controller (p. 54), on/off commands received from scenarios controllers (p. 54, 55), or any other lighting control in the installation, on its lighting circuit -wire installation in box depth 50 mm recommended Self-regulating against overloads PLC transmitter/receiver and IR receiver dimmer switches with indicator Display the light level via LEDs (5 blue LEDs) Faulty load indicated by red LED 67 x 00 W Multi-load Protected against short-circuits 67 4 x 600 W Resistive and inductive loads Lighting scenarios controller PLC transmitter and IR receiver lighting scenarios controller Used to switch on and off a group of switches or dimmer switches and manage lighting scenarios Ideal for increasing the number of control points dedicated keys for on/off and dimming +/- functions -wire connection Phase and eutral Installation in box depth 50 mm recommended utomatic switch PLC transmitter/receiver automatic switch 67 5 x 000 W - ny load utomatic switch for control by detection of the circuit connected to the terminals Manual override possible Transmitter function: for the on/off control of other switches or controls in the installation Receiver function: to execute commands received from scenario controllers (p. 54, 55), or from any other lighting control in the installation, on its lighting circuit djustable light level, lighting period and detection sensitivity Infrared detection Range: to 0 m Time delay: s to 6 min Light level threshold: to 000 lux Horizontal angle: 80 -wire installation in box depth 50 mm recommended Red catalogue numbers: ew products For the on/off control of local or remote circuits Transmitter function: for the remote on/off control of other light switches in the installation Receiver function: to execute commands received (via PLC or IR) from scenario controllers (p. 54, 55), or from any other lighting control in the installation, on the lighting circuit(s). ny load -wire installation in box depth 50 mm recommended PLC transmitter/receiver and IR receiver switches with indicator Display, via the indicator light, the status of the output being controlled 67 0 Single switch x 500 W Lighting environment controller PLC transmitter/receiver lighting environment controller Used to create and manage lighting environments Its transmitter function allows it to control switches, dimmer switches and electric blind switches It can be used to create scenes consisting of scenarios maximum (5 with instantaneous tripping, 7 with delayed tripping and "ll off" scenario) In receiver mode, the scenes can be controlled by a dimmer switch, an IP xiophone, a scenario controller with touch screen or a remote control The scenes can be either: - Static: initiated instantly - Cyclical: the scenarios run in succession at a defined regular interval - Random: the scenarios are executed randomly (simulating occupation) - Programmed: 7 day scenario programme Equipped with a LCD screen for displaying the current scene Scenario controllers IR mobile scenario controller 88 0 Can control up to 6 scenarios by infrared technology LR 0 batteries supplied IR remote control scenario llows the IR control of: - In One by Legrand products with IR receiver - 4 scenarios - TV utomatic learning procedure LR 0 batteries supplied Céliane (p. 58) Galea life (p. 648) (p. 590) (p. 60)

4 PLC lighting control power line carrier technology with Legrand wiring accessories ranges Centralise your lighting dimmers with lighting points in room PLC lighting scenario switch to control dimmers with a single action + - Control a number of lighting points with a single action - Simplified wiring : no more need for wiring between appliances - Possibility to add mobile scenario controllers Range 00 W multi load PLC dimmers 600 W (inductive/resistive load) PLC lighting scenarios controllers Céliane Galea Life White Dark grey White Metal Increase the number of lighting points in a corridor with automatic switches Range PLC automatic switch Céliane 67 5 Galea Life 7756 L - White Dark grey White Metal Increase the number of lighting points in a corridor (no limit of lighting points number) - Simplified wiring : no more need for wiring between appliances Control your lighting without moving PLC switch in a room with one lighting point PLC mobile scenario switch to control switch without moving Range PLC switch with indicator Céliane 67 0 PLC mobile scenarios controllers 88 0 Galea Life White Dark grey White Metal (optional control of a TV set) + - Possibility to control a switch via a remote control - o more need to wire up an additional switch in order to have another control point Light up a display window according to the day and time Programme the time settings for a lighting environment The lighting loads are connected to remote control dimmers Cat.o 06 0 in the consumer unit Range PLC lighting environment controller Céliane Galea Life

5 PLC roller blinds control power line carrier technology with Céliane TM range PLC roller blinds control power line carrier technology with Legrand wiring accessories ranges Centralise roller blinds control 67 5 (Titanium) 67 5 (ickel Velvet) Cover plates, plates and supports selection chart (p. 549 to 565) Particularly suitable for new buildings and heavy renovation Can be installed in living areas, reception areas, working areas (stores, restaurants, medical centres...) Can be controlled by IR from the same room or by PLC with lighting scenarios controller or scenarios controllers (p. 54, 55) Pack Cat.os Roller blinds switches PLC transmitter/receiver and IR receiver individual blind switches Control all types of 0 V electric blind motors to lower/raise/stop blinds with end stops Slat orientation function by long press Transmitter function: to control other individual blind switches in the installation Receiver function: to execute, on the motor connected to the terminals of the switch, commands received from: scenario controllers (p. 54, 55), individual or centralised electric blind switches Installation in box depth 50 mm recommended Max. loads at 0 V : x 500 V Incompatible with Budendorff motors 67 5 Individual switch PLC transmitter and IR receiver centralised blind switches Transmitter switch for centralised control of a set of individual switches for electronic blinds Installation with phase and neutral in box depth 50 mm recommended 67 5 Used to control one group of individual switches for electrical blinds Has two auxiliary inputs that can receive commands via potential-free contacts from conventional products (time switch, light-sensitive, switch etc.) to automate control. Indication of activation via blue LED Wind/sun safety kit 06 0 Controls awnings or blinds automatically in the event of a too strong wind or excessive brightness - The sensor is installed without wiring and without batteries outside in a place exposed to the wind and sun djustment of wind safety (between 7 and 80 km/h) and luminosity/brightness threshold; sending of measurements by radio to the control module Recharged independently by solar energy - The control module is installed in the electrical consumer unit, connected on phase and neutral The transmitter function allows it to send raise/lower commands by PLC or Radio to the individual switch controlling the awning or blind Céliane (p. 5) Galea life (p. 654) (p. 59) (p. 6) + - Individual PLC roller blinds switch installed close to the blind to be controlled, flush-mounted, connected on the 0 V and to the terminals of the blind motor Install in the heart of the home, a PLC centralised roller blinds switch, flush-mounted and connected on the 0 V Using the remote control, launch scenarios Control all individual switches can be centralised, reducing the amount of wiring - Possibility to add mobile scenario controllers Range PLC individual roller blinds switch PLC centralised roller blinds switch Céliane Galea Life White Dark grey White Metal utomatic opening of the blinds according to the sun and wind Wind/sun safety kit compressing: - Wind/sun sensor located on the eaves, on the same side of the house as the awning - Control module located in the consumer unit : receives the sensor commands and sends them to the individual awning switch Receiver individual awning switch: controls awning raising/lowering. Can be installed as a replacement for an existing control using the same wiring : - possibility of increasing the number of individual switches - it is possible to control the awning manually, unless the wind exceeds the preset safety threshold Range Wind/sun safety kit PLC individual roller blinds switch Céliane White Dark grey White Metal 88 8 These products are part of Power Line Carrier technology system > See p Red catalogue numbers: ew products

6 PLC heating control power line carrier technology with Céliane TM range PLC heating control power line carrier technology with Legrand wiring accessories ranges Control your heating locally or remotely (Titanium) Cover plates, plates and supports selection chart (p. 549 to 565) Particularly suitable for new buildings and heavy renovation Can be installed in living areas, reception areas, working areas (stores, restaurants, medical centres...) Pack Cat.os Thermostats For oil or gas boilers, radiant ceiling panels, direct underfloor heating Room thermostat djustment range 7 to 0 C djustment accuracy ± 0.5 C Direct connection of 8 contact for new building work or combined with the PLC receiver Cat.o (p. 57) for installation near the boiler for refurbishment work Programmable room thermostats 7 day programming Constant display of the current programme on screen djustment range 7 to 0 C djustment accuracy ± 0.5 C adjustable temperature levels Permanent programme backup Working reserve 00 hours PLC thermostat 0/0 V Breaking capacity 8 max. Direct connection of 8 contact for new building work or combined with the PLC receiver Cat.o (p. 57) for installation near the boiler for refurbishment work Scenarios controllers For remote control of all In One by Legrand functions: lighting, blinds, heating PLC transmitter scenarios controller Can control 4 scenarios Indication of activation via blue LED -wire connection - Phase and eutral Installation in box depth 50 mm recommended Switched sockets Used for on/off control of the light connected to the socket PLC transmitter/receiver mobile switched socket 500 W To be directly connected to an existing P+E socket "O/OFF" functions of the associated load Incandescent and halogen lamps 0 V s receiver can execute the orders received from other PLC switches or from any scenarios controller (p. 54, 55) 88 6 German standard British standard Céliane (p. 5) Galea life (p. 656) (Mandarin) L Remote control Connect the underfloor heating circuit to a PLC multifunction receiver switch Install a PLC room thermostat It transmitts on/off commands to the multifunction switch according to the desired temperature Install an IP xiophone It receives commands via the internet from a computer or mobile phone n optional scenario switch can be added: - leaving scenario: reference temperature - 4 C - scenario can be modified remotely ( hours before returning: reference temperature) Range Keep the house at the right temperature at the right time with an oil or gas boiler PLC multifunction switch PLC thermostat IP axiophone Connect the oil or gas boiler control unit contact to a PLC receiver modular multifunction switch Install a PLC programmable thermostat It transmits on/off commands to the multifunction switch according to the desired temperature to the nearest degree, on the days and at the time programmed PLC scenario switch Céliane Galea Life (white cover plate) Range PLC multifunction switch PLC programmable thermostat Céliane Galea Life Red catalogue numbers: ew products 445

7 PLC detectors power line carrier technology with Céliane TM range PLC detectors power line carrier technology with Legrand wiring accessories ranges Cut-off your water supply in the event of a leak and receive an alert on your scenario controller 675 (Titanium) 446 Cover plates, plates and supports selection chart (p. 549 to 565) For installation in living areas, reception areas, offices and workplaces (shop, restaurant, medical centres, etc) Pack Cat.os Detectors To limit risks and ensure the safety of people and property in a house, detectors for use in the home are essential. They can be used to control locally and/or remotely an actuator (solenoid valve) and raise an alarm in the same room or in another room lso equipped with a C/O relay, a buzzer and LEDs Flood detector 675 Detects the presence of a conducting liquid by activating the C/O relay and sending a scenario to activate an actuator or inform a controller of the leak Supplied with sensor and a m cable For mounting in a -gang Batibox box depth 50 mm Town gas or methane detector 675 Detects the presence of fuel gases such as town gas (methane) by activating the C/O relay and sending a scenario to activate an actuator or inform a controller about the leak Conforming to standard E 5094 For mounting in a -gang Batibox box depth 50 mm Butane/propane gas detector Detects the presence of fuel gases such as butane/propane by activating the C/O relay and sending a scenario to activate an actuator or inform a controller about the leak Conforming to standard E 5094 For mounting in a -gang Batibox box depth 50 mm IP axiophone 06 8 To be installed inside an electric switchboard (size 6 modules) Power supply: 0 V Has to be connected to the L (RJ socket) llows the control of 0 scenarios and can relay the information of 5 events Compatible with any product of the market equipped with web browser (PC, mobile phone, PD ) and connected to the internet (fixed internet connection or mobile version like Wi-Fi) Can directly control PLC products llows the displaying of any messages with its "Free text" zone (on its first page) Lexic modular interface 4 modules PLC transmitter/receiver multifunction switch For installation in the electrical consumer unit to control or circuits linked to its terminals in one of 4 different operating modes: pushbutton, switch, time switch, latching relay The receiver function is used to execute, on its circuits, on/off commands received from scenarios controllers (p. 54, 55) or any other lighting control in the installation The transmitter function is used for on/off control of other lighting switches in the installation Possibility of switching off the whole installation by a scenario irrespective of the operating mode selected lso has auxiliary inputs for executing, on its circuits, on/off commands received by a potential-free contact Galea life (p. 664) Solenoid valve Install a water leak detector in a place at risk (kitchen, laundry room, etc ) If it detects a conducting liquid, the detector can activate a solenoid valve via multifunction switch Cat.o which automatically closes off the water supply If tripped, your scenario controller will display the action on its screen Cut-out your gas supply in the event of a leak and receive a remote alert L 06 8 Red catalogue numbers: ew products Range PLC flood detector PLC multifunction PLC switch scenarios controllers Céliane Galea Life Install a gas detector in a place at risk (kitchen, boiler room, etc ) If it detects a leak, the detector can activate a solenoid valve via multifunction switch Cat.o which automatically closes off the incoming gas supply (manual reset mandatory) It can be combined with the IP axiophone Cat.o 06 8 for remote alerting Solenoid valve Remote control PLC gas detector Range Methane Butane Propane Céliane Galea Life PLC multifunction switch IP xiophone

8 scenario controls for remote controls Media Server power line carrier (PLC) technology IP axiophone installation principle Example of use of the Media Server Remote access ITERET Wap - Telephone Communication Remote PC DTI DSL filter Modem DSL router Switch Local installation L In One By Legrand Local PC L IP xiophone Heating Create the communication network for the house Install a cabinet for communication network Install RJ 45 sockets: one per computer, one close to the TV Lighting Roller blinds L Heating control L L L Install and use the Media Server Install the Media Server software on each of the networks computer (CD supplied) 4 Connect the Media Server and use the remote control supplied to select, to listen and watch on TV videos, images, music stored on the computers IP axiophone operating principle Secure login screen which allows local or remote internet access to control installation Customisation of scenarios Possibility of controlling and saving up to 0 scenarios Screen for remote control of different scenarios (lighting, blinds, heating, etc ) with message confirming the scenario launched Screen for viewing different events so/as to be alerted in the event of an intruder, technical detection, etc in a house These products are part of Power Line Carrier technology system > See p Legrand_Wiring_Celiane_PLC_en_08.pdf Helsinki tel automation@klinkmann.fi St. Petersburg tel klinkmann@klinkmann.spb.ru Moscow tel moscow@klinkmann.spb.ru Yekaterinburg tel yekaterinburg@klinkmann.spb.ru Samara tel samara@klinkmann.spb.ru Кiev tel klinkmann@klinkmann.kiev.ua Riga tel klinkmann@klinkmann.lv Vilnius tel post@klinkmann.lt Tallinn tel klinkmann.est@klinkmann.ee Мinsk tel minsk@klinkmann.com