Technology for building automation. Ambient Air Humidity and Temperature Probes HT12 and HTF12. Device Description. Contents

Transcription

1 Ambient Air Humidity and Temperature Probes HT12 and HTF12 HT12 and HTF12 serve to seize the relative ambient air humidity and the ambient temperature. The probes are utilised with or without set-point adjuster for continuous measuring in connection with steady regulation. Contents subject to change Edition: 11/05/2004 Contents Ambient Air Humidity and Temperature Probes HT12 and HTF12 Page 1 Contents Page 1 Notes on the device description Page 2 Application Page 3 Types Page 3 Technical data Page 3 Assembly Page 4 Assembly Instructions Page 4 Installation Page 5 Connecting plan HT12 Page 6 Connecting plan HTF12 Page 6 Kieback & Peter GmbH & Co KG Tempelhofer Weg 50, D Berlin Telephone +49 (0) 30 / Telefax +49 (0) 30 / info@kieback-peter.de

2 Notes on the device description The description contains instructions on using and assembling the Ambient Air Humidity and Temperature Probes HT12 and HTF12. In case of questions which cannot be clarified with this device description, please refer to the supplier or manufacturer for further information. The indicated installation instructions/regulations are valid in the Federal Republic of Germany. When utilizing the devices in other countries, the builder or operator of the plant is responsible for the observation of the respective national regulations. The operating staff is to be instructed in accordance with the description of the technical data sheet. Safety Instructions When mounting and utilizing the devices, the respective worker s protection rules, regulations for prevention of accidents and VDE rules shall be observed Any work concerning the assembly, installation or initial operation of the devices shall be exclusively carried out by qualified specialists, see section Qualified specialists. Every person utilizing the devices shall have read and understood the descriptions in the technical data sheet. Meaning of the symbols in the technical data sheet: Danger Warning of dangerous electrical voltage Danger means mortal danger, severe bodily injuries or serious material damage in case of non-observance. Qualified specialists Qualified specialists for the purposes set out in this technical data sheet are persons who are familiar with the described devices and possess a qualification for their respective occupation. These are for instance: Authorization to connect the devices according to the local regulations and authorization to switch the devices on and off taking the in-house regulations into account. Knowledge of the regulations for prevention of accidents. Knowledge of the utilization of the devices within the plant system. etc. Page 2 / 8

3 Application The Ambient Air Humidity and Temperature Probes HT12 and HTF12 serve to continuously seize the relative air humidity and ambient temperature in housing space and business premises. The probes can be operated in connection with all Kieback & Peter regulators and regulation systems containing analogue V entries and sensor connections for the active measuring unit KP10. As an additional feature, the set-point adjuster of the Ambient Air Humidity and Temperature Probe HTF12 enables the setting of the required ambient temperature. Types HT12 HTF12 Combined Ambient Air Humidity and Temperature Probe with humidity probe and active measuring unit KP10 without setpoint adjuster Combined Ambient Air Humidity and Temperature Probe with humidity probe and active measuring unit KP10 with additional set-point adjuster (10 k Ohm) HT12 Technical data Mains 24 V AC ±10 %, 0,4 VA Measured variable relative ambient air humidity and ambient temperature in housing space and business premises Measuring system for humidity Humidity probe with measuring transmitter, Output: V DC, max. 5 ma for % r. h. for temperature active measuring unit KP10 Output: 2,73 V bei 0 C, TK 10 mv/k adjustment at works Exactitude rel. humidity ±3 % at 22 C Temperature ± 0,25 K at 22 C Measuring range rel. Humidity % r. h. Temperature C HTF12 Environmental max % r. h. non condensing humidity Ambient temperature Temperature C Set value adjuster (HTF12) potentiometer 10 k Ohm, linear, set knob with trend arrow Storage temperature C Housing Housing made of plastic material Colour RAL9010 (pure white) Degree of enclosure IP30 protection Dimensions HT12 L x H x W = 82 x 87,5 x 27,5 (mm) T HTF12 L x H x W = 82 x 87,5 x 28.3 (mm) H B Page 3 / 8

4 Assembly The assembly of the combined Ambient Air Humidity and Temperature Probes HT12 and HTF12 can be wallmounting or buried wiring respectively. For a quick and correct detection of the room temperature the room probe shall be installed as to be able to detect the airflow in the room. The vent slots of the hood must be located vertically above one another. Airflow 1,5 m Correct for housing space and business premises False Assembly Instructions Connect the room probe in accordance with terminal connecting plan, position the hood and tighten the safety screw. Release safety screw and 1 take off hood. 3 Tweak for cable entry 60 The cardboard box serves as protective cover during the installation phase. For this purpose, please fold the side boards to the inside and rip off the box cover. M3 x 20 Tweak for cable entry from above ,5 x 45 4 Page 4 / 8

5 Installation Danger Electric installation and probe connection shall be carried out by qualified experts only. Before connecting the Ambient Air Humidity and Temperature Probe to the regulation unit, the switchboard shall be switched voltage-free. In this context, the regulations of the VDE (Association of German Electro technical Engineers) as well as the local regulations shall be observed. The Ambient Air Humidity and Temperature Probes HT12 and HTF12 contain perforated bases and caps for connection purposes. These pieces can be tweaked out in order to insert cables. A B Cable inlet for assembly with flush-mounted box Cable inlets for wall-mounting Page 5 / 8

6 Connecting plan HT12 KP10 HT12 H% + _ Temperature KP Humidity V DC = % r. F V DC 0 V AC/DC 24 V AC 0 V AC/DC Mains 24 V AC Connecting plan HTF12 10 k KP10 HTF H% Temperature KP10 Humidity V DC = % r. F V DC 0 V AC/DC 24 V AC 0 V AC/DC Mains 24 V AC Page 6 / 8

7 Page 7 / 8

8 Page 8 / 8