Edge Data Center - DSE CRAC Settings w/monochrome Display v6.4 Revision Date 12/12/2016

Transcription

1 Edge Data Center - DSE CRAC Settings w/monochrome Display v6.4 Revision Date 12/12/2016 Parameter (Line User Display Set-up (Page 1) U409 Display Shows Data Of Unit Set to the U2U Address on each Unit U411 System On/Off Enabled S102 Service Setpoint Menu (Page 1) Temperature Control Sensor Supply S103 Temperature Setpoint Act/Set 68F/68F S104 Temperature Control Type PI S106 Temperature Proportional /Integral 20F/3min S107 Temperature Derivate Time 0sec S108 AutoSet Enable S109 Temperature Deadband 2F S110 Supply Limit Enabled/Setpoint S111 Heater Deadband 0F S113 Service Setpoint Menu (Page 2) Enable Temp Compensation S118 Comp Cap Filter at 0-100%.6/.6% S119 Capacity Transition Filter 4% S121 BMS Backup Temp Setpoint 73F S122 2nd Temperature Setpoint 73F S124 Service Setpoint Menu (Page 3) Humidity Control Sensor Return S125 Humidity Setpoint 53F S126 Humidity Control Type Dewpoint S127 Humidity Proportional Band 8F S128 Humidity Integration Time 0min S129 Humidity Deadband 4F S132 Dehum Reheat/LL Sensor/Set Supply/68F S133 Dehum Low Limit 1 LL1/LL2-5F/-12F S13A Dehum Reheat Prop Band2 14F S13B Estimated Aisle Temp Disabled Service Setpoint Menu (Page 5) S146 Fan Control Sensor Return Sensor S147 Fan Setpoint 78F S148 Fan Temp Control Type PI S149 Fan Temp Prop/Integral 35F/0.0min S150 Fan Deadband 1F S151 Airflow Calibration 9.6V S152 Fanspeed Min/STD 55/100% S153 Fanspeed Dehum/ Power 55/100% S154 Allow Fan Modulation on Comp Yes S155 High Return Limit Enable Local S15A High Return Temperature Limit 85F S15B Return Limit P-Band 20F

2 Parameter (Line Service Setpoint Menu (Page 6) S157 Fan Startup Time/Speed 3sec/100% S158 Fanspeed Filter at 0-100%.2/1% S159 Fanspeed Transition Filter 1% S160 Fanspeed Reposition Mode/Delay Decel 0sec S161 Max Deceleration Rate 0.10% S162 BMS Backup Fan Setpoint 73F S163 BMS Backup Fan Operation Disabled S164 Allow BMS to change Fanspeed S165 BMS is Connected To 0 S166 High Temp Limit Approach 300s/100% S16A High Temp Limit Approach At S16B FC / AirEco Ramp Up w/ CFC Service Setpoint Menu (Page 7) S168 Fan Back Draft Control Enabled S169 VSD Setpoint BACK DRAFT 1.0V S171 t Selectable Zone 1 3.5/4.9V S172 t Selectable Zone 2 0.0/0.0V S173 Stop BDR when System is Off S175 Display Off and BDR BACKDRAFT S176 BMS Off and BDR BACKDRAFT S177 LOC Off and BDR BACKDRAFT Service Set Alarms Menu (Page 1) S203 High temp setting 90'F S204 Low temp setting 60'F S205 High humidity setting 70% S206 Low humidity setting 30% Service Set Alarms Menu (Page 2) S213 Supply Air Temp Alarm Time Delay 300 sec S215 Dew Point Alarms/ Init Delay ENABLED S216 High/Low Dew Point 60'F/36'F Service Set Alarms Menu (Page 4) S241 High Room Hum Disabled S242 Low Room Hum Disabled Service Option Set-up Menu (Page 2) S419 Dehum System/Unit/Fan Ctrl Yes/Yes/Yes Service Standby Settings / Lead-Lag Menu (Page 1) S502 Number of Standby Units Setting based on kw of Load S503 Rotation Frequency Every Wednesday S504 Rotate at Hour 10 S505 Rotate by Minute 0 S506 Perform one Rotation 0 () S512 Standby Fan Timer at Reheat/Hum 1 min S513 Start all Standby Units by HT Yes

3 Parameter (Line Service Standby Settings / Lead-Lag Menu (Page 2) S515 Cascade Units Fanspeed S516 Cascade Units on Delay 10 min S517 Cascaded Units Quick Start 2 min S518 Cascaded Units Control Delay 5 min S519 Cascaded Units Off Delay 0 min S520 Cascaded Units Min Run 30 min S521 Start Next SYS Fanspeed 100% S522 Max Intermediate System Speed 100% S523 Stop Next SYS Fanspeed 70% Service Network Set-up Menu (Page 1) S803 Teamwork Mode 3 (Optimized Aisle) S804 Teamwork is based on Average S805 Qty Units Included in Average Based on the number of Networked Units S806 Virtual Master Enabled Advanced Expert Settings Menu (Page 1) A512 Load Compressor Every 30 min A513 Load Duration 60 sec Advanced Expert Settings Menu (Page 5) A564 Humid disable at Ret Temp / Hys 95 /5 Advanced EconoPhase Menu (Page 1) P003 Prop Band Switchover 30% Advanced EconoPhase Menu (Page 2) P026 Mcap Sensor Supply

4 Edge Data Center - DSE CRAC Settings w/ Touch Screen Display v6.4 Revision Date 12/12/2016 Parameter (Line Service_Setpoint_Temperature Control Menu Temperature Control Sensor Supply Temperature Setpoint Act 68 F Temperature Control Type PI Temperature Proportional /Integral 20 F/3min Temperature Derivate Time 0sec Temperature Deadband 2 F BMS Backup Temp Setpoint 73 F Supply Limit Enabled/Setpoint Heater Deadband 0 F AutoSet Enable Dehumidification Reheat Temperature Control Sensor Supply Dehumidification Reheat Setpoint 68 F Dehumidification Reheat Proportional Band 14 F Service_Setpoint_Temperature Compensation Menu Temperature Compensation Service_Setpoint_High/Low Limit Control Menu Supply Limit Enabled/Setpoint Dehumidification Low Limit Sensor Supply Dehum Low Limit Setpoint 66 F Dehum Low Limit 1-5 F Dehum Low Limit 2-12 F Service_Setpoint_Humidity Control Menu Dew Point Setpoint 53 F Humidity Control Type Dewpoint Dew Point Proportional Band 8 F Humidity Integration Time 0min Dew Point Deadband 4 F Service_Setpoint_Fan Control Menu Fan Control Sensor Return Sensor Airflow Calibration 9.6V Minimum Fan Speed 55% Maximum Fan Speed 100% Fan Setpoint 78F Fan Temp Control Type PI Fan Proportional Band 35 F Fan Intergral Time 0.0min Fan Deadband 1 F Static Pressure Fan Control

5 Parameter (Line Service_Options Setup_Fan Settings Menu Fan Speed at Unit Start Timer 300sec Fan Speed at Unit Start 100% Fan Shutdown Delay Timer 0sec Airflow Calibration 9.6V Minimum Fan Speed 55% Maximum Fan Speed 100% Dehumidification Fanspeed 55% Power Fan Speed 100% Allow Fan Modulation with Comp Yes Fan Backdraft Mode Enabled Backdraft Setpoint 1.0V t Selectable Zone 1 Start 3.5V t Selectable Zone 1 End 4.9V t Selectable Zone 2 Start 0.0V t Selectable Zone 2 End 0.0V Stop System Off BD Display Off BACKDRAFT BD BMS Off BACKDRAFT BD LOC Off BACKDRAFT Fanspeed Filter at 0% 0.20% Fanspeed Filter at 100% 1% Fanspeed Transition Filter 1% Fanspeed Reposition Mode Decel Fanspeed Reposition Delay 0sec Max Deceleration Rate 0.10% Service_Alarms & Events_Return Sensor Alarms Menu High Dew Point 60 F Low Dew Point 36 F High Room Temp 90'F Low Low Room Temp 60'F High Room Hum (Press tifications Button to Disable) Disabled Low Room Hum (Press tifications Button to Disable) Disabled Service_Alarms & Events_Supply Sensor Alarms Menu Supply Temperature Alarms Enable Enabled Supply Sensor Init Delay 300 sec Hi Supply Temperature 75 F Lo Supply Temperature 60 F Service_BMS & Teamwork Setup_Teamwork / Standby_Standby Menu Start all Standby Units by HT Yes High Temperature Threshold 85 F Number of Standby Units Setting based on kw of Load Standby Fan Timer at Reheat / Humidification 1 min

6 Parameter (Line Service_BMS & Teamwork Setup_Teamwork / Standby_Unit Rotation Menu Rotation Frequency Every Wednesday Rotate by 1 Rotate at 10:00am Service_BMS & Teamwork Setup_Teamwork / Standby_Teamwork Mode Menu Type 3 Optimized Aisle Based On Average Cascade Units Fanspeed Cascade Units Delay 10 min Cascaded Units Off Delay 0 min Cascaded Units Quick Start 2 min Cascaded Units Min Run 30 min Cascaded Units Control Delay 5 min Cascaded Units Min Run 30 min Start Next SYS Fanspeed 100% Max Intermediate System Speed 100% Stop Next SYS Fanspeed 70% A512 Advanced_Expert Settings Menu Load Compressor Every 30 min A513 Load Duration 60 sec A564.1 Humid disable at Return Temp 95 F A564.2 Humid Disable Hysteresis 5 F Advanced_EconoPhase Menu P003 Prop Band Switchover 30% P026 Mcap Sensor Supply Advanced_Parameter Directory Menu S806 Virtual Master Enabled