Λευκωσία, 8 Νοεμβρίου ΠΡΟΣ: Όλα τα Μέλη. Κυρία/ε,

Transcription

1 Λευκωσία, 8 Νοεμβρίου 2018 ΠΡΟΣ: Όλα τα Μέλη Κυρία/ε, Σας επισυνάπτoυμε γνωστοποιήσεις από Εθνικούς Οργανισμούς Τυποποίησης, μελών των Ευρωπαϊκών Οργανισμών Τυποποίησης CEN/CENELEC, που περιέχουν τους τίτλους προτεινόμενων εθνικών προτύπων. Σύμφωνα με την Ευρωπαϊκή Οδηγία που αφορά την πληροφόρηση σε θέματα τεχνικών προτύπων, μπορείτε, αφού μελετήσετε τους τίτλους: α) να ζητήσετε όπως λάβετε ηλεκτρονικά ολόκληρο το κείμενο του προσχεδίου εθνικού προτύπου, εάν αυτό είναι διαθέσιμο, β) να συμμετάσχετε στις συναντήσεις της τεχνικής επιτροπής του Εθνικού Οργανισμού Τυποποίησης που ετοιμάζει το προσχέδιο προτύπου και γ) να υποβάλετε εισήγηση στον CYS, να αρχίσει τυποποιητική εργασία σε Ευρωπαϊκό επίπεδο σχετικά με το θέμα της γνωστοποίησης, εάν φυσικά πιστεύετε ότι το εν λόγω εθνικό πρότυπο θα επηρεάσει την ελεύθερη διακίνηση προϊόντων ή την κυπριακή βιομηχανία και οικονομία. Τυχόν σχόλια και παρατηρήσεις παρακαλώ όπως υποβάλλονται στον Κυπριακό Οργανισμό Τυποποίησης. Σε περίπτωση που δε λάβουμε καμία ανταπόκριση, ο CYS δε θα φέρει ένσταση στην προώθηση των υπό αναφορά εθνικών προτύπων. Για περισσότερες πληροφορίες μπορείτε να επικοινωνείτε με την κα. Μαριλένα Νικολάου, Λειτουργό Διοίκησης και Διεθνών Σχέσεων του Κυπριακού Οργανισμού Τυποποίησης (CYS), τηλ: , Φαξ και στην ηλεκτρονική διεύθυνση: m.nicolaou@cys.org.cy Με εκτίμηση, Ανδρέας Ανδρέου, Διευθυντής Βιομηχανίας, για Γενικό Γραμματέα. /ΜΚ. Λεωφ. Γρίβα Διγενή 38 & Δελιγιώργη 3, 1066, Τ.Θ 21455, 1509 Λευκωσία, Κύπρος Τηλ , φαξ , meropi@ccci.org.cy, Ιστοσελίδα:

2 Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from to Register issued on : A list of subsectors can be found at the end of this document.

3 Information procedure Page 2 Monthly Notifications Register Notifications registered at CCMC from to Sector A : SERVICES Register issued on :

4 Subsector A05: MAINTENANCE SERVICES Page 3 Subsector : A05 Registration Date : UNI Italy ID : / National Ref : UNI Maintenance - Maintenance within physical asset design This standard specifies principles, criteria, methodologies and procedures, as well as informativeelementsandindicatorsrelatingtomaintenance. They are to be considered and included in the design process of a physical asset in order to ensure over the life cycle the characteristics, levels of performance and lifetime expected, as postedinthegeneraltermsandconditionsofcontractandrelatedtechnicalspecifications. REV/AMD UNI 11454:2012 Subsector : A05 Registration Date : UNI Italy ID : / , , National Ref : UNI Maintenance-AdditionaltermsanddefinitionstoEN13306 This standard gives the most used terms in the maintenance field to be considered together to those of EN REV/AMD UNI 10147:2013 ** End of Sector **

5 Information procedure Page 4 Monthly Notifications Register Notifications registered at CCMC from to Sector B : BUILDING AND CONSTRUCTION Register issued on :

6 Subsector B01: FIRE PROTECTION Page 5 Subsector : B01 Registration Date : DIN Germany ID : /0001 National Ref : Firefighting and fire protection - Outlet standpipe nominal pressure PN 16 - Outlet standpipe 2 B Subsector B02: STRUCTURES Subsector : B02 Registration Date : BAS Bosnia and Herzegovina ID : / National Ref : pnbas /NA:2018 Eurocode 3: Design of steel structures Part 1-1: General rules and rules for buildings National Annex This document defines the value of national parameters or certain procedures for the calculation with the standard BAS EN :2017 and applied together with that standard. Subsector : B02 Registration Date : BAS Bosnia and Herzegovina ID : / National Ref : pnbas /NA:2018 Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings - National annex This document defines the value of national parameters or certain procedures for the calculation with the standard BAS EN :2017 and applied together with that standard. Subsector : B02 Registration Date : UNMZ Draft Issue Date : Czech Republic Latest Date for Comments : ID : /0001

7 Page 6 National Ref : Supplementary guidance for atmospheric icing on structures The aim of the new standard is unification of the standard according to the other standards. REV/AMD CSN (2018) Subsector B03: CONCRETE Subsector : B03 Registration Date : SNV Draft Issue Date : Switzerland Latest Date for Comments : ID : CH180011/0001 Draft for public enquiry National Ref : prsia 2030 Recycled concrete REV/AMD SIA 2030:2010 Subsector B08: DOORS AND WINDOWS Subsector : B08 Registration Date : DIN Germany ID : /0001 National Ref : Criteria for the use of windows and exterior doors in accordance with DIN EN Subsector : B08 Registration Date : DIN Germany ID : /0001 National Ref : Elastomer glazing and panel gaskets for windows and claddings - Technical delivery conditions - Part 1: Non celluar elastomer glazing and panel gaskets Subsector : B08 Registration Date : DIN

8 Germany ID : /0001 National Ref : Elastomer glazing and panel gaskets for windows and claddings - Technical delivery conditions - Part 2: Celluar elastomer glazing and panel gaskets Page 7 Subsector : B08 Registration Date : UNE Spain Latest Date for Comments : ID : P /0001 Draft for public enquiry National Ref : PNE Powered pedestrian doors. Installation, use and maintenance. This Standard specifies the information to be given by the manufacturer of the Powered Pedestrian Door and by the producer of its components, to ensure a correct installation, use and maintenance of doors which main objective is giving safe access for pedestrian use in buildings or rooms, for public or private uses. REV/AMD UNE 85121:2010 EX Subsector B09: THERMAL MATTERS Subsector : B09 Registration Date : UNI Italy ID : / National Ref : UNI Opaque envelope components of buildings - Thermo-physical parameters This technical report provides the main thermo-physical parameters (thermal transmittance, heat capacity per unit area and periodic thermal transmittance) of the opaque envelope components most commonly used in existing buildings. These parameters can be used for energy assessments of existing buildings in the absence of more detailed information about the materials forming the structure. REV/AMD UNI/TR 11552:2014 Subsector : B09 Registration Date : UNI Italy ID : /

9 Page 8 National Ref : UNI In situ measurement of thermal transmittance of building elements by infrared thermography - Quick method This document describes a methodology for measuring the thermal transmittance of opaque buildingelementsonexistingbuildingsusinganinfraredthermalcamera. This method also allows to carry out a quantitative assessment of any constructional defects (thermalbridges)presentintheconstructionelements. Thedocumentalsopresentsthelimitsofthemethodology. Subsector B24: AUXILIARY AND HANDICRAFT WORK Subsector : B24 Registration Date : UNI Italy ID : / , National Ref : UNI Resilient and laminate floor coverings - Part 2: Knowledge, skill and competence requirements for installers of resilient and laminate floor coverings This standard defines the installer profile of resilient and laminate floor coverings outlining the essential requirements, the knowledges, skills and competences to distinguish and characterize the professional installer in the field of constructions towards public and private clients, building contractors, designers, regulators, etc. REV/AMD UNI :2015 Subsector : B24 Registration Date : UNI Italy ID : / , National Ref : UNI Discontinuous roofing - Requirements for roofer qualification Part 1: Knowledge, skill and competence requirements This standard describes requirements for roofer qualification. These requirements are defined in terms of knowledge, skills and competence, in accordance with the European Qualifications Framework, EQF. Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT Subsector : B25 Registration Date : UNI Italy

10 Page 9 ID : / , National Ref : UNI Burning systems equipped with forced draught gas burners of nominal heat input greater than 35 kw - lnspection and maintenance This standard provides operations to be carried out, according to the instructions given by the manufacturer of the appliances and components, on the combustion plants equipped with gas forced burners in order to guarantee safety and efficiency under normal working conditions. Itgivesrecommendationsfor: -maintenanceofplants -checkoftheoccurredmaintenanceandtheperformanceleveloftheplanttowardsthe safetyandtherationaluseoftheenergy It applies to the combustion plants intended for the ambient heating and/or domestic hot water production, equipped of automatic forced gas burners, including mixed and combined ones(asreferredtothegas)havingheatinputgreaterthan35kw. Thestandarddoesnotcoverplantsforindustrialproductionprocesses. REV/AMD UNI 10435:1995 Subsector : B25 Registration Date : UNI Italy ID : / National Ref : UNI Gas meters with metering pressure not greater than 0,07 bar Criteria for verification Thisstandarddefines: a) the requirements to carry out verification of the meter in the laboratory and at the end user; b) the technical operational procedure to be applied to carry out verification of the meter andthemethodofcalculatingthemeasurementerror; c)thecharacteristicsofthemeasuringequipmentnecessarytocarryouttheverification; d)theprocedureforremovalandtransporttothelaboratory; e)therequirementsoflaboratorieswheretheverificationofthemeteriscarriedout. It applies to all meters for measuring gas of the second and third family, performing the measurement at a pressure not greater, respectively of 0.04 bar (4 kpa) for natural gas, and 0.07bar(7kPa)formixturesofLPG REV/AMD UNI 11003:2017 Subsector : B25 Registration Date : DIN Germany ID : /0001 National Ref : Hose assemblies of stainless steel for gas according to DIN EN Additional connections

11 Page 10 Subsector B27: WATERPROOFING MATERIALS Subsector : B27 Registration Date : UNI Italy ID : / , National Ref : UNI Building Tests of products for discontinuous roofing Part 14: Determination of mechanical resistance of fastener elements This standard provides a test method for determination of mechanical resistance of fastener elements of sealing layer. REV/AMD UNI :1986 Subsector : B27 Registration Date : UNI Italy ID : / , National Ref : UNI Building Tests of products for discontinuous roofing Part 15: Determination of number for area unit and areic mass This standard provides a test method for determination of number for area unit and areic mass. REV/AMD UNI :1986 Subsector : B27 Registration Date : UNI Italy ID : / , National Ref : UNI Building Tests of products for discontinuous roofing Determination of alkali enclosure in fine clay products This standard provides a test method for determination of alkali enclosure in fine clay products. REV/AMD UNI :1986

12 Subsector B28: FLOOR COVERINGS Page 11 Subsector : B28 Registration Date : UNI Italy ID : / National Ref : UNI Resilient and laminate floor coverings - Part 1: Instruction for the design, installation and maintenance This standard gives instructions for the design, installation and maintenance of resilient and laminate floor coverings. REV/AMD UNI :2015 ** End of Sector **

13 Information procedure Page 12 Monthly Notifications Register Notifications registered at CCMC from to Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS Register issued on :

14 Subsector C02: PAINTS AND RELATED PRODUCTS Page 13 Subsector : C02 Registration Date : ISS Serbia Latest Date for Comments : Draft for public ID : /0001 enquiry National Ref : nasrps H.C8.993:2019 Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings This practice measures the volatile organic compound (VOC) content of solventborne and waterborne paints and related coatings as determined from the quantity of material released from a sample under specified bake conditions and subtracting exempt volatile compounds andwaterifpresent. Note 1: The regulatory definition, under the control of the U.S. EPA, can change. To ensure currency,contactthelocalairpollutioncontrolagency. This practice provides a guide to the selection of appropriate ASTM test methods for the determinationofvoccontent. Certain organic compounds that may be released under the specified bake conditions are not counted toward coating VOC content because they do not participate appreciably in atmospheric photochemical reactions. Such negligibly photochemically reactive compounds arereferredto,asexemptvolatilecompoundsinthispractice. Note 2: Information on the US EPA definition of VOC and a list of the current US EPA approved exempt volatile compounds which have been used in coatings, are provided in AppendixX3. VOC content is calculated as a function of (1) the volume of coating less water and exempt volatile compounds, and (2) the volume of coating solids, and (3) the weight of coating solids. Subsector : C02 Registration Date : DIN Germany ID : /0001 National Ref : Binders for paints and varnishes - Cellulose ethers - Testing Subsector : C02 Registration Date : DIN Germany ID : /0001 National Ref : Binders for paints and varnishes - Cellulose esters of organic acids - Testing

15 Page 14 Subsector C20: EXPLOSIVES AND FIREWORKS Subsector : C20 Registration Date : ISS Serbia Latest Date for Comments : ID : /0001 Draft for public enquiry National Ref : Instantaneous electric seismic detonators This standard determines the basic measures, quality and quality control of instantaneous seismic electric detonators. ** End of Sector **

16 Information procedure Page 15 Monthly Notifications Register Notifications registered at CCMC from to Sector F : FUNDAMENTAL STANDARDS Register issued on :

17 Subsector F05: MEASURING INSTRUMENTS Page 16 Subsector : F05 Registration Date : UNI Italy ID : / , National Ref : UNI Communication systems for meters - Shared management of communication band at 169 MHz This technical specification establishes the requirements for shared management of communications in the unlicensed 169 MHz frequency band and the coexistence of various services related to different utilities (e.g. gas, electricity, water, heat). Subsector F07: DOCUMENTATION AND INFORMATION Subsector : F07 Registration Date : UNI Italy ID : / National Ref : UNI Information and documentation - International Image Interoperability Framework (IIIF) This standardization initiative focuses on the technical specifications of the IIIF interoperability protocol, widely used on an international scale in digital libraries implemented for library and archival holdings, and museum collections. Subsector F19: OPTICS Subsector : F19 Registration Date : DIN Germany ID : /0001 National Ref : Quality evaluation of optical systems; determination of veiling glare Subsector F20: QUALITY ASSURANCE

18 Subsector : F20 Registration Date : UNE Spain Latest Date for Comments : Draft for public ID : P /0001 enquiry National Ref : PNE Health services. Quality management systems for the clinical and dietetic nutrition units in adults This standard specifies the requirements for the establishment of a quality management systemapplicabletotheclinicalanddieteticnutritionunits(cdnu). Thescopeofthestandardencompassestheprocessesinvolvedinthefollowingaspects: a)nutritionalriskscreening; b)managementofconsultationstothecdnu; c)nutritionalassessment; d)nutritionaldiagnosisandcoding; e)estimation/calculationoftotalenergyexpenditure; f)prescriptionofnutritionaltreatment: 1.oraldiet, 2.oralnutritionalsupplements, 3.enteralnutrition, 4.parenteralnutrition; g)monitoringofthenutritionalstatusandtreatment; h)managementofhomeartificialnutrition; i)healtheducationandtrainingoncareandnutritionaltreatment. IftheCDNUconsidersappropiate,itcanaddtothescope: j)teaching; k) Research Page 17 ** End of Sector **

19 Information procedure Page 18 Monthly Notifications Register Notifications registered at CCMC from to Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE Register issued on :

20 Subsector H04: SPORTS EQUIPMENT Page 19 Subsector : H04 Registration Date : DIN Germany ID : /0001 National Ref : Playing field equipment - Basketball equipment - Requirements and test methods ** End of Sector **

21 Information procedure Page 20 Monthly Notifications Register Notifications registered at CCMC from to Sector I : MECHANICAL ENGINEERING Register issued on :

22 Subsector I02: FASTENERS Page 21 Subsector : I02 Registration Date : DIN Germany ID : /0001 National Ref : Hose clamps with worm gear drive; shape A Subsector : I02 Registration Date : DIN Germany ID : /0001 National Ref : Hose clamps - Part 4: Technical delivery conditions Subsector I04: ROLLING BEARINGS Subsector : I04 Registration Date : DIN Germany ID : /0001 National Ref : Rolling bearings - Dimensions - General plan Subsector : I04 Registration Date : DIN Germany ID : /0001 National Ref : Rolling bearings; tolerances for rolling bearings; tolerances for radial bearings

23 Subsector I09: SMALL TOOLS Page 22 Subsector : I09 Registration Date : DIN Germany ID : /0001 National Ref : Indexable hardmetall (carbide) inserts with wiper edges, without fixation hole Subsector : I09 Registration Date : DIN Germany ID : /0001 National Ref : Tool holders for internal turning, with cylindrical shank, for indexable inserts; style F Subsector : I09 Registration Date : DIN Germany ID : /0001 National Ref : Tool holders for internal turning, with cylindrical shank, for indexable inserts; style K Subsector : I09 Registration Date : DIN Germany ID : /0001 National Ref : Sheet metal anchorage with threads; manufacturing processes Subsector : I09 Registration Date :

24 Page 23 DIN Germany ID : /0001 National Ref : Sheet metal anchorage with threads; dimensions for tools and their design Subsector I11: MACHINE TOOLS Subsector : I11 Registration Date : DIN Germany ID : /0001 National Ref : Saw blades for woodworking; technical specifications for circular saw blades with hardmetal tips Subsector : I11 Registration Date : DIN Germany ID : /0001 National Ref : Circular saw blades for woodworking, with hardmetal tips; dimensions, number of teeth Subsector : I11 Registration Date : DIN Germany ID : /0001 National Ref : Double Equal-Angle Milling Cutters; Dimensions and technical delivery conditions Subsector : I11 Registration Date :

25 Page 24 DIN Germany ID : /0001 National Ref : Semi-circular Profile Milling Cutters, Concave; Dimensions and technical delivery conditions Subsector I18: MINING Subsector : I18 Registration Date : PKN Poland ID : / National Ref : prpn-g Hard coal, coke and semi-coke of hard coal and char -- Determination of moisture -- Simplified methods The standard defines the basic methods for the determination of various types of moisture in the sample of the soild fuels - coal, brown coal, coke, semi-coke and char. The standard contains the description of the methods Determination of the trasient moisture content in hardcoal Determinationofthetotalmoisturecontent: -two-stepdeterminationofthetotalmoisturecontentinahardcoal -one-stepdeterminationofthetotalmoisturecontentinahardcoalwithuseofadryer - one-step determination of the total moisture content in a coal according to a distillation method -determinationofthetotalmoisturecontentinacokeandsemi-cokefromahardcoal -determinationofthetotalmoisturecontentinachar Determinationofthetotalmoisturecontentintheair-driedsample -determinationofthetotalmoisturecontentintheair-driedsampleofacoal - determination of the total moisture content in the air-dried sample of a coke and semicokefromahardcoal - determination of the total moisture content in the air-dried sample of a char Subsector : I18 Registration Date : PKN Poland ID : / National Ref : prpn-g Mining shafts -- Shaft equipment -- General principles of testing The general principles of shaft reinforcement have been defined. Methods for testing the elements of shaft reinforcement, requirements for the equipment as well as the method of

26 Page 25 performing the tests on the site were described. The method of interpretation of test results and the scope of test documentation were established. Subsector : I18 Registration Date : PKN Poland ID : / National Ref : prpn-g Mining shafts -- Shaft linings -- Assessment criteria and test methods The scope of the standard has been extended to include the most common shaft lining type ie concrete / reinforced concrete, tubing, brick, wooden and special (panel, steel-shell). Methods for testing the above-mentioned lining types, requirements for their use, as well as requirements for the equipment for testing have been described. The method of conducting tests at the facility and in the laboratory was determined. Criteria for assessing the technical condition of the lining have been established, taking into account the specificity of its construction. Subsector I30: AIR DISTRIBUTION Subsector : I30 Registration Date : AFNOR France ID : /0001 National Ref : PR NF E Complement to EN "Ventilation for buildings - Performance testing and installation checks of residential ventilation systems" ** End of Sector **

27 Information procedure Page 26 Monthly Notifications Register Notifications registered at CCMC from to Sector M : METALLIC MATERIALS Register issued on :

28 Subsector M01: STEEL Page 27 Subsector : M01 Registration Date : AFNOR France ID : /0001 National Ref : PR NF A Steel tubes - Welded rings, made of non-alloy steel, internally threaded, for pressure equipment. Subsector M03: FOUNDRY TECHNOLOGY, INCLUDING CAST IRON Subsector : M03 Registration Date : AFNOR France ID : /0001 National Ref : pr NF A Foundry products Abrasion resistant cast steels ** End of Sector **

29 Information procedure Page 28 Monthly Notifications Register Notifications registered at CCMC from to Sector N : NON-METALLIC MATERIALS Register issued on :

30 Subsector N03: PETROLEUM PRODUCTS Page 29 Subsector : N03 Registration Date : SIST Draft Issue Date : Slovenia Latest Date for Comments : ID : / , National Ref : osist 1030:2018 Petroleum products - Liquefied petroleum gases - Commercial mixtures of propanebutane - Fuels for housekeeping and general use - Requirements and test methods This national standard defines required characteristics liquefied petroleum gases - commercial mixtures of propane-butane and additional information which must be assured by producers. Required characteristics are for fuels for housekeeping and general use. Subsector : N03 Registration Date : PKN Poland ID : / , National Ref : prpn-c Petroleum products Determination of dynamic viscosity and density of liquids using Stabinger viscometer and calculation of kinematic viscosity of base oils, lubricating oils and heating oils This standard specifies the method for simultaneous measurement of the dynamic viscosity and density of base oils, lubricating oils and heating oils in the temperature range from - 60 C to 135 C, in the dynamic viscosity range from 6,2 mm2/s to 20,000 mm2/s and density from 0,60 g/cm3 to 3,0 g/cm3. The kinematic viscosity is calculated automatically from the relationship between the density and dynamic viscosity values determined at the same temperature. The result obtained using this test method depends on the behavior of the sample and the method is intended for use in liquids for which the shear stress and shear rate are proportional (tonian liquids). However, when the viscosity varies significantly with the change in shear rate, comparison of the present determination method with other measurement methods is only allowed for similar shear rate values. Subsector N05: TEXTILES Subsector : N05 Registration Date : UNI Italy ID : / , National Ref : UNI Textiles - Product specification for the production, preparation, marketing and traceability oftheangorarabbitfibre This product specification applies to the Angora rabbit breeding management and to the

31 Page 30 collection and management of the fiber. Subsector N06: RUBBER Subsector : N06 Registration Date : ISS Serbia Latest Date for Comments : ID : /0001 Draft for public enquiry National Ref : nasrps G.C0.014:2018 Specification for packaging and identification of vulcanized rubber items 1.1 This British Standard specifies the requirements for the packaging and identification when packaged of vulcanized rubber materials, components and assemblies containing rubber components used for aerospace purposes unless amended by other contractual requirements. 1.2 The packaging specified not only ensures adequate identification of the components, but also forms an integral part of the controlled storage and inspection procedure (see British Standard F 68). Subsector : N06 Registration Date : ISS Serbia Latest Date for Comments : ID : /0001 Draft for public enquiry National Ref : nasrps G.C0.015:2018 Controlled storage of vulcanized rubbers for use in aerospace applications 1.1 This British Standard specifies requirements for the storage, and inspection during storage, of vulcanized rubber, whether in the form of materials or as components to be used for aerospace purposes. These requirements also apply to items made from cellular rubber. 1.2 The requirements of this standard do not apply to rubber components contained within mechanical assemblies, e.g. pumps and valves. NOTE In such cases the recommendations of the assembly supplier for exercising the assembly and lifing of the rubber need to be sought and applied. 1.3 The storage periods quoted apply only if the storage conditions specified in Annex A are complied with and if the packaging complies from the date of cure with the requirements of BS F 69, as far as is practicable, making allowance for subsequent manufacturing operations. 1.4 The storage period comprises the whole period of existence of the rubber from the date of cure. This period will generally be divided between manufacturing (including assembly) and storage (e.g. in manufacture, by stockists, by aircraft constructors and operators) and the division of this period should be mutually agreed between the interested parties. 1.5 These requirements are based on the classification of rubbers into groups as defined in Clause 3.

32 Page 31 Subsector : N06 Registration Date : AFNOR France ID : /0001 National Ref : PR NF P Jointing products - Sealants for gluing clay tiles - specifications and test methods Subsector N10: CORK Subsector : N10 Registration Date : UNE Spain Latest Date for Comments : ID : P /0002 Draft for public enquiry National Ref : PNE Agglomerated microgranulated cork stoppers for still wines. This standard aims to establish tests methods and requirements for agglomerated microgranulated cork stoppers used for still wines bottles, according to UNE-EN Subsector N13: LEATHER Subsector : N13 Registration Date : UNI Italy ID : / National Ref : UNI Leather - Characteristics and requirements of leather for leather goods and accessories This document specifies the general requirements and the characteristics (with the relevant test methods) for the evaluation of leather for leather goods and accessories. REV/AMD UNI 10826:2012 Subsector : N13 Registration Date : UNI Italy ID : / National Ref : UNI

33 Leather - Characteristics of leather to be used in footwear industry This standard provides the characteristics and the requirements, with the relevant test methods,fortheevaluationofleatherintendedtobeusedinfootwearindustry. Page 32 REV/AMD UNI 10594:2010 ** End of Sector **

34 Information procedure Page 33 Monthly Notifications Register Notifications registered at CCMC from to Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT Register issued on :

35 Subsector S01: ACOUSTICS AND SOUND INSULATION Page 34 Subsector : S01 Registration Date : SNV Draft Issue Date : Switzerland Latest Date for Comments : ID : CH180010/0001 Draft for public enquiry National Ref : prsia 181 Sound insulation in buildings REV/AMD SIA 181:2006 Subsector S16: AIDS FOR THE DISABLED Subsector : S16 Registration Date : UNE Spain Latest Date for Comments : ID : P /0001 Draft for public enquiry National Ref : PNE EX Guide in Easy-to-read for validators of documents This experimental standard provides a guide to be followed for the validation of documents ineasy-to-read. This experimental standard applies to document validators in Easy-to-read. Subsector S23: PERSONAL & PROPERTY PROTECTION AGAINST AGGRESSION/ BURGLARY Subsector : S23 Registration Date : SIS Draft Issue Date : Sweden Latest Date for Comments : ID : / National Ref : 3880 High security locks - Requirements and testing This standard specifies requirements and testing methods for high security locks for security cabinetsandsafesorothertypesofstoragedeviceswheresuchrequirementsaremade. Thestandardalsoincludesrequirementsfordirectoperationofthehighsecuritylock. Remote control systems, using wired or wireless communication (distributed systems) are not covered by this standard.

36 Subsector S24: SOIL QUALITY Page 35 Subsector : S24 Registration Date : NEN Netherlands ID : / , , National Ref : NEN 5744:2018 Concept nl Soil quality - Sampling of groundwater This standard describes the sampling of groundwater as part of soil investigation. Subsector S99: UNDETERMINED Subsector : S99 Registration Date : SFS Draft Issue Date : Finland Latest Date for Comments : ID : 0000E503/0001 Draft for public enquiry National Ref : Characteristics and requirement levels of steel fire doors in different applications ** End of Sector **

37 Information procedure Page 36 Monthly Notifications Register Notifications registered at CCMC from to Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING Register issued on :

38 Subsector T01: SHIPBUILDING AND MARITIME STRUCTURES Page 37 Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Ships and marine technology - Flanges on castings extra light duty - DN 32 to DN 50, PN up to 25, DN 65 to DN 125, PN up to 10 - Principles of design Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Fire extinguishing and wash deck installation; hose couplings, armatures, hoses, accessories; summary of types for shipbuilding Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Ships and marine technology - Flanged gate valves extra light duty - DN 32 to DN 125, PN 10 Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Shutt off valves for shipboard use, of gun metall, with flanges, DN 15 to 500

39 Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Non return valves for shipboard use, cutt off type, of gun metall, with flanges, DN 15 to 500 Page 38 Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Spuares with tapered and parallel sides for valves for shipboard use Subsector : T01 Registration Date : DIN Germany ID : /0001 National Ref : Operating devices for valves for shipboard use - Crank handles with square hole with tapered sides Subsector T02: AEROSPACE Subsector : T02 Registration Date : DIN Germany ID : /0001 National Ref : Aerospace series - Hexagon bolts, close tolerance, with short-length MJ thread, titanium alloy, nominal tensile strength 1100 MPa, for temperatures up to 315 C; Text in German and English

40 Page 39 Subsector : T02 Registration Date : DIN Germany ID : /0001 National Ref : Aerospace - Screws, hexagon bolts with MJ thread, threaded approximately to head, titanium alloy - Nominal tensile strength 1100 MPa, for temperatures up to 315 C; Text in German and English Subsector T03: ROAD VEHICLES Subsector : T03 Registration Date : LVS Draft Issue Date : Latvia Latest Date for Comments : ID : /0001 Draft for public enquiry National Ref : LVS 63:2015/prA3 Emergency road vehicles, their painting and equipment Standard sets additional requirements for Ministery of Justice - Prison Administration vehicles, their painting and equipment REV/AMD LVS 63 Subsector T19: ROAD SAFETY Subsector : T19 Registration Date : SNV Draft Issue Date : Switzerland Latest Date for Comments : ID : CH180012/0001 Draft for public enquiry National Ref : prsn Naturalhazardsonroadinfrastructure s basic standard Subsector : T19 Registration Date : SNV Draft Issue Date : Switzerland Latest Date for Comments :

41 Page 40 ID : CH180013/0001 Draft for public enquiry National Ref : prsn Public lighting in road tunnels, galleries and underpasses, basic standard Subsector T20: TRAM- AND RAILWAY ENGINEERING Subsector : T20 Registration Date : UNI Italy ID : / National Ref : UNI Railway vehicles - Design, installation, validation and maintenance of fire detection and extinguishingsystemstobeutilizedinrailvehicles-generalprinciples The scope of this standard is to define functional and performance requirements to be satisfied and criteria to be followed for design, installation, validation and maintenance of fire detection and extinguishing systems to be utilized in rail vehicles. REV/AMD UNI 11565:2016 ** End of Sector **

42 List of non-electrotechnical subsectors Sector A: Services Subsector Title ISO/TC CEN/TC reference reference A01 Tourist services / 329; CEN/WS ETO A02 Cleaning services / 328 A03 Postal services / 331 A04 Transportation services / 320; CEN/WS 016; CEN/WS SCUTUM A05 Maintenance services / 319 A06 Building and construction services / 330 A07 Translation services / A08 Funeral services / CEN/BT/TF 139 A09 Facility management / 348 A10 Services of Real Estate Agents / CEN/BT/TF 180; 373 A11 Security Services / CEN/BT/TF 167; 391; 384; 370; CEN/WS 044; CEN/CLC/TC 4 A12 Consultancy Services / 395; 381 A13 Expertise Services / 405 A14 Aesthetic Services / 403;409 A99 Undetermined / CEN/WS 002; CEN/WS 004; CEN/WS 037; CEN/WS 039; CEN/WS 041; CEN/WS 051; 375; 374; 376; 385; 404

43 Sector B: Building and construction Subsector Title ISO/TC CEN/TC reference reference B01 Fire protection 21 70; 72; 191; 192 B02 Structures 59; ; 167; 250; 277; 346; 349; 284; 288; 297; 340 B03 Concrete ; CEN/WS 009 B04 Cement 74; B05 Fire tests B06 Gypsum / 241 B07 Glass B08 Doors and windows B09 Thermal matters ; 89; 371; CEN/BT WG 173; CEN/WS 036 B10 Timber structures B11 Metal structures B12 Masonry 179; ; 246 B13 Solar energy B14 Geotechnics ; 396 B15 Sanitary appliances / 163; 7 B16 Taps / / B17 Lighting equipment and lighting / 50; 169 application technology B18 Scaffolding / 53 B19 Ceramic tiles B20 Drainage equipment / 165 B21 Baths / / B22 Wallcoverings / 99 B23 District heating / 107 B24 Auxiliary and handicraft work / / B25 Gas distribution installation and / 234; 235; 282 related equipment B26 Road building and maintenance / 178; 227 B27 Waterproofing materials / 128; 254; 361; 314 B28 Floor coverings 38/SC B29 Aggregates / 154 B30 Floor and surfacing / 217; 303; 323; 390 B31 Heating systems in buildings / 228; 247 B32 Precast concrete products / 177; 229

44 B33 Building design ; 325; 388 B34 Building and construction Environmental aspect 350; 351 B99 Undetermined / /

45 Sector C: Chemicals, chemical engineering and food products Subsector Title ISO/TC CEN/TC reference reference C01 Food products ; 275; 302; 360; 307; 327; 338; 387; CEN/WS 008; CEN/WS 018; CEN/WS 054 C02 Paints and related products ; 298; 173 C03 Chemistry ; 363 C04 Laboratory glassware C05 Lac / / C06 Essential oils 54 / C08 Pesticides 81 / C09 Surfactants C10 Starch 93 / C11 Tobacco C12 Glass plant / / C13 Fertilizers ; 260 C16 Wood preservatives / / C17 Trees and plants / / C18 Adhesives / 193 C19 Chemical analysis 201; ; 347 C20 Explosives and firework / 212; 321 C21 Cosmetics C22 Bio-Based products / 411 C99 Undetermined / 386

46 Sector F: Fundamental standards Subsector Title ISO/TC CEN/TC reference reference F01 Technical drawings 10 / F02 Units & symbols 12 / F03 Preferred numbers 19 / F04 Sieves 24 / F05 Measuring instruments 30; ; 171; 176; 237; F06 Terminology principles 37 / 294; 318; 244; 367; 141; CEN/WS 011 F07 Documentation and information ; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS F08 Surfaces / 290 F09 Banking 68 / F10 Statistics 69 / F12 Information processing systems ; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365 F13 Environmental tests / / F14 Graphical technology, 130 / sign-boards and nameplates F15 Material testing in general ; CEN/WS 007 CEN/WS 021 CEN/WS 033 F16 Graphical symbols 145 / F17 Administrative documents 154 CEN/WS MMU F18 Micrographics 171 / F19 Optics 172; ; 170 F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS F21 Value analysis and project / 279 network F22 Logistics / 379; 273 F23 Energy 203 CEN/CLC/JWG 1; CEN/CLC/JWG 2;

47 CEN/CLC/JWG 3; CEN/CLC/JWG 4; CEN/WS 027 F99 Undetermined / 389; CEN/WS 057; CEN/WS 058; CEN/WS 060

48 Sector H: Products for household and leisure use Subsector Title ISO/TC CEN/TC reference reference H01 Cinematography H02 Photography 42 / H03 Consumer questions / 291 H04 Sports equipment H05 Oil and gas burners / 47; 131 H06 Horology 114 / H07 Space heating ; 110; 130; 179; 180 H08 Sizing systems 133; 137 / H09 Furniture H10 Sewing machines 148 / H11 Heater controls H12 Ceramic and glass-ware for food 166 / H13 Jewellery 174 CEN/WS 047 H14 Caravans H15 Toys H17 Oil stoves / 46 H18 Central heating boilers / 48; 57; 109; 269 H19 Non-electric cookers and barbecues / 49; 281; 295 H22 Smokers lighters and matches / 355; 87 H23 Ladders / 93 H24 Tactile danger warnings / / H25 Large gas appliances / 106; CEN/CLC/JWG FCGA H26 Sealing materials / 108; 208 H27 Educational equipment / / H28 Hunting 191 / H29 Heat pumps / 113 H30 Equipment for children / 252 H31 Dedicated LPG appliances / 181 H32 Culinary utensils H33 Footwear (excluding protective / 309 footwear) H34 Child safety / CEN/BT/WG H99 Undetermined / 299; 364; 369; 402

49 Sector I: Mechanical engineering Subsector Title ISO/TC CEN/TC reference reference I01 Screw threads 1 / I02 Fasteners I03 Limits & fits / / I04 Rolling bearings 4 / I05 Iron pipes I06 Pressure vessels I07 Shafts 14 / I08 Agricultural machines , 334 I09 Small tools I10 Splines / / I11 Machine tools ; 143; 145; 255 I12 Pulleys & belts I13 Gas containers 58 23; 286 I14 Gears 60 / I15 Equipment for petroleum industry I16 Internal combustion engines 70; I17 Machinery in general 72; ; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025 I18 Mining I19 Nuclear energy 85 / I20 Refrigeration 86 44; 182 I21 Chains and chain wheels 100 / I22 Vacuum technology 112 / I23 Pumps I24 Industrial fans I25 Compressors I26 Plain bearings 123 / I27 Earth moving and construction 127; equipment I28 Fluid power 131 / I29 Gas cleaning / 195 I30 Air distribution / 156 I31 Valves 153; ; 236; 105 I32 Flanges / 74 I33 Information processing in automation I34 Non-ferrous metallic pipes / /

50 I35 Leisure and recreational machines / 152 I36 Thermoprocessing technology / 186 I37 Printing and paper machines / 198 I38 Leather production, tannery and / 200; 201 related machinery I39 Machines for metal processing / 202; 322 I40 Industrial piping networks / 267 I41 Membrane filters / 272 I42 Potentially explosive atmospheres / 305 I43 Hydrogen energy 197 / I44 Nanotechnologies I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2; 65, 157; CEN/WS 059

51 Sector M: Metallic materials Subsector Title ISO/TC CEN/TC reference reference M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110 M02 Zinc / 209 M03 Foundry technology, ; ECISS/TC 31 ECISS/TC 111 including cast iron M04 Copper M05 Welding M06 Dimensions of wrought products / / M07 Manganese and chromium 65 / M08 Light alloys M09 Iron ores 102 / M10 Metallic coatings M11 Powder metallurgy 119 / M12 Aluminium ores 129 / M13 Ferroalloys 132 / M14 Nickel 155 / M15 Metallic corrosion ; 219

52 M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101 M17 Heavy metal ores 183 / M18 Metal wire products / ECISS/TC 30; CEN/BT/TF 196; 378; 407 M20 Tin and tin alloys / 220 M21 Precious metals / 283 M22 Lead and lead alloys / 306 M99 Undetermined / /

53 Sector N: Non-metallic materials Subsector Title ISO/TC CEN/TC reference reference N01 Paper and board N02 Solid fuels ; 343;383; CEN/WS 019 N03 Petroleum products 28 19; 336; CEN/WS 038; CEN/WS 061 N04 Refractories N05 Textiles ; 248 N06 Rubber ; 366 CEN/WS 003 N07 Sawn timber 55 38; 175 N08 Mica / / N09 Plastics N10 Cork 87 / N11 Wood-based panels N12 Timber products 99 / N13 Leather N14 Plastics pipes N17 Fluorspar 175 / N18 Glass-fibre reinforced plastics / / N19 Tapes / 253 N20 Ceramics N21 Gaseous fuels and combustible gas 158; ; 408 N22 Feather and related materials / 222 N23 Diamond / 410 N99 Undetermined / /

54 Sector S: Health, environment and medical equipment Subsector Title ISO/TC CEN/TC reference reference S01 Acoustics and sound ; 211 insulation S02 Transfusion equipment 76 / S03 Syringes 84 / S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162; CEN/WS 026; CEN/WS 043 S05 Dentistry S06 Vibration & shock S07 Anaesthetic and respiratory equipment S08 Air quality ; 243; 264; CEN/CLC/JWG CMI S09 Water quality and water supply ; 230; CEN/WS 001 CEN/WS 034 S10 Surgical implants ; CEN/CLC/JWG AIMD S11 Contraceptives 157 / S12 Gas analysis / / S13 Ergonomics S14 Prosthetics 168 / S15 Surgical instruments 170 / S16 Aids for the disabled S17 Respiratory protective devices / 79 S18 Sterilization of equipment ; 204 S19 First aid equipment and rescue systems / 239 S20 Waste collection, handling and / 183 transportation S21 Laboratory medicine, clinical ; 206; 233; pathology and biosafety 257; 258; 316; CEN/CLC/TC 3; CEN/WS 031; CEN/WS 053; CEN/WS 055 S22 Energy saving / CEN/WS 005 CEN/WS 015 S23 Personal & property protection against aggression/burglary protection / 263 S24 Soil quality ; CEN/WS 032

55 S25 Chemical disinfectants and / 216 antiseptics S26 Environmental management 207 CEN/TC 406; CEN/WS 040 S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120 S28 Demining / CEN/WS 029 CEN/WS 013 S99 Undetermined / 205; CEN/BT/TF ; 259; 357; 358; 359; 380; 400; CEN/WS PCEC CEN/WS 012 CEN/WS 020

56 Sector T: Transport, mechanical handling and packaging Subsector Title ISO/TC CEN/TC reference reference T01 Shipbuilding and maritime 8; ; 300 structures T02 Aerospace ; AECMA; ECSS ;377 T03 Road vehicles ; 326 CEN/WS IMA T04 Tyres 31 / T05 Pallets 51 / T06 Metal and plastic containers ; 221; 265; 266; 268; T07 Glass containers 63 / T08 Cranes T09 Materials handling and ; 149 storage equipment T10 Freight containers ; 280 T11 Steel wire ropes 105 / T12 Industrial trucks ; 324 T13 Lifting chains, hooks and ropes T14 Packaging ; 120 T15 Cycles T16 Lifts & escalators ; 242 T17 Builders hoists / / T18 Elevating platforms / 98 T19 Road safety / 226; 339 T20 Tram- and railway engineering / 256; / CEN/CLC/WG FPR T21 Packaging machines / 146 T22 Off-road vehicles / 354 T99 Undetermined / CEN/WS TAF

57 Sector Z: Information technology Subsector Title ISO/TC CEN/TC Z01 Radiocommunication for IT / / Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI Z03 Common O.S.I. activities / CEN/CLC - EWOS Z99 Undetermined / 353; CEN/WS ADN; CEN/WS AUT; CEN/WS BII; CEN/WS CAT; CEN/WS CST; CEN/WS CTC; CEN/WS DFA; CEN/WS DIR; CEN/WS DIS; CEN/WS DPA; CEN/WS DPP; CEN/WS EBE; CEN/WS ECH; CEN/WS ECO; CEN/WS EFI; CEN/WS EMD; CEN/WS ESI; CEN/WS ESR; CEN/WS EUR; CEN/WS FAS; CEN/WS FIN; CEN/WS FS2; CEN/WS FUN; CEN/WS GEN; CEN/WS HIC; CEN/WS ICT; CEN/WS IEC; CEN/WS IHM; CEN/WS INV2; CEN/WS ISD; CEN/WS JXF; CEN/WS KMA; CEN/WS LCT; CEN/WS LTS; CEN/WS MDC; CEN/WS MEE; CEN/WS MES; CEN/WS MET; CEN/WS MLX; CEN/WS MMI; CEN/WS NEA; CEN/WS NOM; CEN/WS ORC; CEN/WS POR; CEN/WS QIS; CEN/WS SAN; CEN/WS SCE; CEN/WS TEX; CEN/WS TWE; CEN/WS UDP; CEN/WS URI; CEN/WS WAC;

58 CEN/WS XFS; CEN/WS XML; CEN/WS ego; CEN/WS ein; CEN/WS epr

59 REGISTER OF NEW NATIONAL STANDARDIZATION INITIATIVES NOTIFIED UNDER SUBSECTORS IN THE SCOPE OF CENELEC October 2018 Issued on : 7 November 2018

60 Page 1 Information Procedure on Standards Notifications registered at CCMC during October 2018 Sector W : ELECTRICAL ENGINEERING Register issued on : 7 November 2018

61 Subsector W27: ELECTRICAL INSTALLATIONS IN BUILDINGS Page 2 Subsector : W27 Registration Date : UNE Spain Latest Date for Comments : ID : P /0002 Draft for public enquiry National Ref : PNE Procedures for the regulatory inspection. Low voltage electrical installations. Part 2-28: Communal facilities. Describes the methodology for the authorised body to perform both the initial and the periodic Inspections foreseen in the current legislation to check compliance with the safety mandatory requirements applicable to the low voltage electrical installations at communal facilities. ** End of Sector **

62 List of Subsectors covering work items in CENELEC s field of activity (version ) (Rows or committees shaded in blue indicate changes compared to the last list of subsectors ) U GENERAL ELECTROTECHNICAL STANDARDS U01 Title IEC TC CLC TC INFORMATION STRUCTURES, DOCUMENTATION AND GRAPHICAL SYMBOLS IEC TC 3 IEC SC 3C IEC SC 3D U02 ALUMINIUM CONDUCTORS. IEC TC 7 U03 SYSTEM ASPECTS FOR ELECTRICAL ENERGY SUPPLY IEC TC 8 CLC TC 8X U04 ELECTRICAL FLUIDS. IEC TC 10 BTTF U05 ELECTRICAL INSULATING MATERIALS AND SYSTEMS. IEC TC 15 IEC TC112 U06 MAN-MACHINE INTERFACE, MARKING AND IEC TC 16 IDENTIFICATION MARKINGS. U07 LETTER SYMBOLS FOR ELECTROTECHNOLOGY. IEC TC 25 U08 ELECTRIC WELDING. IEC TC 26 CLC TC 26A CLC TC 26B U09 INSULATION CO-ORDINATION. IEC TC 28 IEC TC 109 U10 HIGH-VOLTAGE TESTING. IEC TC 42 U11 ENVIRONMENTAL TESTING OF ELECTROTECHNICAL EQUIPMENT IEC TC 89 IEC TC 104 U12 RELIABILITY. IEC TC 56 U15 MAGNETIC ALLOYS. IEC TC 68 U16 PROTECTION BY ENCLOSURES. IEC TC 70 U17 SHORT CIRCUIT CURRENTS. IEC TC 73 U18 ENVIRONMENTAL STANDARDIZATION - GENERAL IEC TC 111 CLC TC 111X U19 RADIO INTERFERENCE, EMC IEC TC 77 + SCs CLC TC 210 CISPR + SCs U20 SUPERCONDUCTIVITY IEC TC 90 U21 NANOTECHNOLOGY IEC TC 113 U91 QUALITY ASSURANCE ISO TC 176 BTTF 76-3 U92 ADVANCED CERAMICS IEC TC * U93 ELECTROMAGNETIC HAZARDS IEC TC 106 CLC TC 106X U94 PUBLIC PROCUREMENT MATTERS CLC TC 218 U95 ENVIRONMENTAL MATTERS BTWG U96 USABILITY & SAFETY OF ELECTRICAL PRODUCTS WITH REFERENCE TO PEOPLE WITH SPECIAL NEEDS U99 UNDETERMINED. (ex: terminology) IEC TC 1 BTWG 101-5