Vulcanised rubber products for cold and hot drinking water applications

Transcription

1 Product certificate K43802/06 Issued Replaces K43802/05 Page 1 of 6 Vulcanised rubber products for cold and hot drinking water applications STATEMENT BY KIWA With this product certificate, issued in accordance with the Kiwa Regulations for Certification, Kiwa declares that legitimate confidence exists that the products supplied by LOPIGOM S.r.l. as specified in this product certificate and marked with the Kiwa -mark in the manner as indicated in this product certificate may, on delivery, be relied upon to comply with Kiwa evaluation guideline BRL- dated inclusive amendment sheet dated Luc Leroy Kiwa 287/ Publication of this certificate is allowed. Advice: consult in order to ensure that this certificate is still valid. Kiwa Nederland B.V. Sir Winston Churchill-laan 273 Postbus AB RIJSWIJK The Netherlands Tel Fax info@kiwa.nl Company LOPIGOM S.r.l. Via Rossini CREDARO Italy Tel Certification process consists of initial and regular assessment of: quality system product

2 page 2 of 6 PRODUCT SPECIFICATION The products as specified in the table below fulfil the requirements of BRL-K BRL-K17504 covers the requirements of EN 681-1, - Materials requirements for pipe joint seals used in water and drainage applications - TECHNICAL SPECIFICATION OF THE PRODUCT Rubber Compound: EPDM Lopi 50 Ozone Class 1 : 50 IRHD I Seal type Cross sections application 2 : O-ring 2-10 mm II WB Rubber Compound: EPDM Lopi IRHD Ozone Class 1 : I Seal type Cross sections application 2 : O-ring 2-10 mm II WB Rubber Compound: EPDM Lopi IRHD application 2 II WB : Ozone Class 1 : I Seal type O-ring Seal type Seal with Stainless Steel reinforcement mm Cross sections 2-10 mm Height 5,6 7,8 mm Rubber Compound: EPDM Lopi 80 Ozone Class 1 : 80 IRHD I Seal type Cross sections application 2 : O-ring 2-10 mm II WB Width Technical Seals, membranes and flat rounds produced with EPDM Lopi 50, Lopi 60, Lopi 70 and Lopi 80 Product codes Cross Sections [mm] [mm] 9380-I 3, I 2, , I 3,8-8 65, I 3,8-8 89, I 4, , I 5, I 6, I 7, I, 9669-I, 9577-I, 9578-I, 9579-I, 9580-I,9581-I, 9582-I 9583-I, 9682-I, 9684-I 2,4 4, Profiles

3 page 3 of I, 9660-I, 9661-I, 9662-I 9663-I, 9664-I, 9713-I 2,3 4, I, 9757-I 9758-I 1,3 4, I 2-2, I 1 2, , I 1,8 3, , P 1,8 12, I 3,5 10, I 1,8 9, ,6 23, I 2,5 7, I I 2,5-4 20, I 6 22, I I 2 2, I I I 4 8, I 4 15, I 1,7 2,7 119, I 1,5 4, I 1,4 2,8 15, I 2,6-2,7 16, I 1, I 3,8-4 9, I 3 3, I 2 4, I 1,5 3, LC8 3 10,3 8, LC8 3 14, LC8 2,5 5, I I 4,7 9, I 2, I 2,7 16, I I I 4 6, I , P 7, I 3, I 3, I 3, I 1,9-5 5, I 0, I 1,2 3, I 1, I 1, I 1,8 2, I 2 6, I 2, I I I 0,5 0, P 1,2 1, P 1-4

4 page 4 of I 3, P 2,5 5, I 3,4 3,5 37, I 2,3 3,8 54, I 1,5 2,5 3, I 2,7-4 5, P 0,6 1,8 5, I 2 2,5 4, I 1,4-7 13, P 0,8 1,2 13, I 1, I I 2 5, I 1 11, I 1 5, I 1, I I 1 3,8 2, I , I 0,5 2, I 0,4 2, P 0,3 1, P 0,2 1,6 32, I 0,6 2,2 23, I 2,5 7, I 1,5-2 16, I 10,3-25 0,7 1, I 8, I 0,9 1,5 12,3 36, P 1-2 6,5 7, P 1,1 2, I 1, I 1 3,5 6,2

5 page 5 of I 4,8-8 20, I 3,3 3,5 10, I 9, I 1,5 5,5 12, I 15, I 1,2 3, I 5,7 5,9 7, P 1,1 3, I-SOSPESO 4,8 7,3 103, I-SOSPESO 5,5 8, P , I 4,8 5, I 9,1 12,7 68, I 3, I 3 4,5 7, I , I 1 3,6 1, I 8 15, I I I 2 3, I 1,3-4,5-1 Ozone resistance class according to BRL-2013: I For products with a high risk of attack by ozone, for instance in case of separately supplied products without sufficient packaging or in case of connections with preinstalled rubbers under strain; II For products for which a normal resistance to ozone is required; III For rubbers which are never (partly) exposed to the open air when they are in tension. Transport shall always take place in sealed packages. 2 application class according to BRL 2013 class: I Cold water supply at temperatures continuously up to 45 C and intermittently up to 95 C; II Hot water supply at temperatures intermittently up to 110 C, or water supply up to 110 C in serviceable piping systems; III Hot water circulation systems based on the classification class 2 in ISO 10508; IV District heating, secondary systems with hot water circulation between 75 C and 95 C. application class according to EN 681-1: WC As in BRL-2013 class I; WD As in BRL-2013 class II; WF As in BRL-2013 class II, for IIR-copolymer; WG As in BRL-2013 class I, oil resistance. Details of the products are included in the drawing list, which forms a part of the IQC schedule. Kiwa authenticates this list. A copy of this list can be obtained from the producer.

6 page 6 of 6 Fitness for contact with drinking water This product is approved on the basis of the requirements for hygienic aspects set in the "Regeling materialen en chemicaliën drink- en warm Gazette). These hygienic aspects are based on two main criteria. The product shall permanently comply with: The product recipe approved during the assessment procedure. This recipe is not to be changed without prior approval by Kiwa according to the Kiwa approval procedure for the hygienic aspects; Specific product requirements for the hygienic aspects. certificate. MARKING The following marks and indications must be provided on each product # and product packaging in a clear, legible and indelible way: the name of manufacturer or the deposited trade mark; Kiwa (or Kiwa word mark) and additionally the Kiwa watermark ; the nominal dimension or dimensions; the nominal hardness; the year of manufacturing and preferably the quarter; type of rubber applied by means of the letter codes of the nomenclature according to ISO 1629; the application class (I, II or III); lass is valid. # If the dimensions of the products are such that the indications applied to them may impair the product, the products may be marked per package in consultation with the manufacturer, the buyer and Kiwa. Products produced by cutting or die cutting out of sheets may be marked per package. APPLICATION AND USE RECOMMENDATIONS FOR CUSTOMERS Check at the time of delivery whether: the supplier has delivered in accordance with the agreement; the mark and the marking method are correct; the products show no visible defects as a result of transport etc. If you should reject a product on the basis of the above, please contact: LOPIGOM S.r.l. and, if necessary, Kiwa Nederland B.V.