FOCAS ppm Bilge Alarm. Product Specifications Rev.1.03 (T)

Transcription

1

2

3 FOCAS ppm Bilge Alarm Product Specifications Rev.1.03 (T)

4 Alteration / correction hysteretic Date Revision The reason for revision / correction Approved Name Rev.1.01 Internal Arrangement Drawing and the Terminal Base Arrangement Change of contact arrangement of terminals Y.Kikuchi Y.Uehara Rev.1.0 List of spare parts changed. Addition note of Φ10 joint set( ) Y.Kikuchi H.okumura 3 Outline dimensions Material etc changed. Added the mounting space Rev.1.03 Y.Kikuchi H.okumura dimensions and note. Note Number in triangle are change or modify ordered

5 Specifications Oil concentration meter FOCAS-000 Main item Specifications Drawing NO. Application Measurement method Operation method Response time Power supply /power consumption Measurement range Measurement accuracy Conditions on sample water Clean water pressure for washing Material measured and identified Battery for clock and lifetime Service temperature humidity Maximum measurement angle of inclination Indications and Outputs Terminal specification /oil alarm operating point Operation recording function Piping bore Cable gland Bilge concentration monitor (bilge drainage) Optical continuous measurement Automatic operation using sample water pressure Within 5sec, comply with MEPC107(49) AC90 ~ 40 V 50 ~ 60 Hz 0 VA or less 30ppm in full scale Within ±5ppm (at 15ppm) pressure : 0.03 ~ 0.3MPa flow rate : 0. ~ 3 L /min water temperature : + ~ +45 C 0.03 ~ 0.6MPa light oil 10ppm in 100ppm iron oxide solution Lithium battery(cr450) about years (recommended manufacturer : FDK Energy Co Ltd. Japan) 0 ~ 50 C 5 ~ 90%RH no dew condensation Within.5 in each direction Indication of oil concentration : displayed in 4 digits lines. alpha-numeral Character LCD oil alarm lamp : red LED blinks Alarm1 Alarm VALVE Each contact output REC Analog output VALVE (for three-way valve) 1 circuit for contact output, 1 B contact (Max AC50V A) Supply voltage output Alarm1 alarm (5~15ppm variable) 1 circuit for contact output, C contact (Max AC50V A)delay time 0~5 seconds Alarm alarm (5~15ppm variable) 1 circuit for contact output, C contact (Max AC50V A)delay time 0~600 seconds REC (Analog output) DC4-0mA(0-4mA) line resistance less than 750Ω Power turn-on and off, time of each alarm output/release (record memory Mbit) comply with MEPC107(49) For sample water inlet, clean water inlet and drain outlet : O.D. of φ8 orφ10 with ring joint for copper pipe(φ8 factory default) 4 pcs(φ10.5 ~ φ14.5) Water-proof grade IP = 54 Coating color Outside dimension weight 7.5BG 7/ (Since this color is manufacturer standard, it cannot be changed.) W=51 mm H=83.5 mm D=1 mm Total weight:approx. 4.8 kg (excluding accessories) (body=approx. 3.0 kg. Sensor unit=approx. 0.6 kg. Solenoid valve unit = 1. kg) - -

6 これらの注意を怠ると 機器の損傷や漏電事故等を生じる恐れがあり また機能上支障となりますので十分に注意して下さい If these attention are neglected,there is a fear to cause damage,electric leakage,etc,of apparatus besides an obstacle in terms of functions may be found,so pay full attention. これらの注意を怠ると 機器の損傷や漏電事故等を生じる恐れがあり また機能上支障となりますので十分に注意して下さい If these attention are neglected,there is a fear to cause damage,electric leakage,etc,of apparatus besides an obstacle in terms of functions may be found,so pay full attention. 型式 M O D E L 製造番号 SERIAL NO. 製造年月 DATE TOKYO JAPAN Outline dimensions Material etc Φ Sensor unit Solenoid valve unit 15ppm Bilge Alarm MODEL FOCAS-000 POWER AL.1 AL. Body unit 8 9 MODEL OF TYPE APPROVAL CANADA NO, USCG No. EC 注意 CAUTION ppm Bilge Alarm FOCAS or more Maximum 65 4-Φ10 4-M8 300 or more or more or more Maximum 354 Unit (mm) Mounting space 3 A distance of at least 10 mm is required on the left. This amount is required for replacing the sensor unit or solenoid valve unit. No. PART NAME QTY MATERIAL REMARKS 1 Sample water outlet 1 C3604 Screwed joint RC 1/4 φ8 orφ10(φ8 factory default) Sample water filter 1 C3604/SUS304 3 Sample water inlet 1 C3604 Screwed joint RC 1/8 φ8 orφ10(φ8 factory default) 4 Clean water filter 1 C3604/SUS304 5 Clean water inlet 1 C3604 Screwed joint RC 1/8 φ8 orφ10(φ8 factory default) 6 drain 1 C Wiring ports 4 Polyamide Cable size φ10.5~φ Case cover 1 ADC-1 9 Snap latch 1 C Earth screw 1 SUS304 M4-3 -

7 Internal Arrangement Drawing and the Terminal Base Arrangement Operations memory Terminal block Alignment and FOCAS-000 inner connection Caution against the voltage Clock backup battery Fuse for the equipment 3.15A 50V x1 Fuse for threeway Valve A 50V x L N FG COM NC NO COM NC NO COM NC AC IN VALVE Alarm 1 Alarm AC OUT AC input Output connected signal for to PS three-way valve Alarm signal 1 Alarm signal External output REC 5 4-0mA (0-4mA) Output terminal Terminal base group 5 1 All terminal blocks are removable. Symbol figures of relay show standby conditions when primary power is supplied. Name Rating Remarks 1 AC IN AC90V~40Vrms, 50~60Hz FG(=frame gland) grounds housing B contact 50VAC, A max. Output signal for VALVE Alarm operating point of Valve and Alarm 1 Supply voltage output three-way valve is synchronized. Delay setting is available C contact 50VAC, A max. Alarm signal 1 (external 3 Alarm 1 for Alarm 1 only. Dry contact signal) C contact 50VAC, A max. 4 Alarm Dry contact Alarm signal (external signal) 5 REC 4-0mA (0-4mA) current output When 0mA is loaded, the line resistance is 750Ωor less List of contact output of relay movement of alarm lamp etc VALVE Alarm1 Alarm Terminal name operation conditions etc between relay terminal between relay terminal COM-NC At outage Standby Primary mode source (no current) Standby No output Warm up No output Operation mode Under set density value Supply voltage output When applying current More than set density value Over 30ppm Over scale Washing mode washing No output Setup mode Customized setup NO-COM Close Open Open Close Close 1 1 COM-NC Open Close Close Open Open alarm lamp (AL1) Light off Light off Blinking Light off Blinking between relay terminal NO-COM Close Open Open Close Close 1 1 COM-NC Open Close Close Open Open alarm lamp (AL) Light off Light off Blinking Light off Blinking factory default 0 Density Density 0 4 value (poweroff) value value unit REC Value assignable by (ma) Density 0 ~ panel operation N/A 0 ~ 4 N/A N/A value or 0 ~4 or or or (step up by 1mA) 0 ~ 4 0~4 0 ~4 0 ~4 1 Reverse movement of contact output is possible by operating panel switch at setup mode, washing mode, warming up. (However, factory shipments are the same outputs as standby. ) unit error - 4 -

8 Spare parts model:focas-000 item oil concentration detector FOCAS-000 Spare Parts Table Hull No. Case No. No Part name Part No. Sketch Material Work-ing backup mass(kg) remarks 1 Fuse for three-way Valve Glass tube Normal Meltdown type A Fuse for the equipment Ceramic tube Fast-blow type 3.15A 3 Upper lid O-ring FKM DP-31 4 Drain seal W SUS/NBR M5 5 Washing brush Washing liquid mL 7 Φ10 joint C RC1/4 1 RC1/8 CHECK kikuchi DESIGN Okumura DRAWIN Okumura DATE MAR APPOINT SCALE TITLE DRAWING NO FOCAS-000 Spare Parts Table

9 Pipe connections Height of Sample water inlet Do not install Bilge Alarm lower than m down from the top of Bilge Separator. Within 1.5m head (recommend) Hopper m or less Overall length Drainage Drain outlet Screwed joint (RC1/4 φ8 ) Bilge Alarm Bilge Separator 3m or less Overall length Sample water inlet (0.03~0.3MPa) Be sure to set Bilge Alarm above the outlet level of Bilge Separator. Screwed joint (RC1/4 φ8 ) Fresh water inlet (Equivalent to Mineral water, at 0.03~0.6MPa ) Hopper Allow the pipe upstand around Bilge Separator outlet to provide Sample water for testing. (In accordance with MEPC.107(49) ) Place the valve near the concentration detector. Sample water and fresh water pipes 1. Tubes to be connected to the sample water inlet, fresh water inlet, and outlet should be copper tubes of 8mm or 10mm in outer diameter.. Use fresh water equivalent to mineral water, which is necessary for sensor correction. 3. Normal operating pressure: 0.03 to 0.3 MPa for sample water and 0.03 to 0.6 MPa for fresh water. 4. In order to prevent dust contamination from fresh water line, please be sure to carry out cleaning of the line. When the Bilge Alarm is shipped from the factory, its connection ports are for tubes of 8mm in diameter (as standard). To connect a 10mm-dia. copper tube, take off φ8 joint and apply seal tape to the threaded part of the copper tube of φ10 joint before coupling the tube to the port. Restrictions on piping 5. The length from the sample water outlet to the end of piping should be within m and the fall should be within 1.5m. Be sure to provide hoppers. 6. Piping length between Bilge Separator and Bilge Alarm should be within 3m. Bilge Alarm should be set above the Outlet height of Bilge Separator. Do not install Bilge Alarm lower than m below the top of Bilge Separator. Operation pressure of Bilge Alarm is 0.03MPa 0.3MPa. In consideration of recommended pressure for Bilge Separator, adjust the operation pressure. Caution: Be sure to follow the above instructions to run the oil concentration detector normally