GROUP A NEW STANDARDS PROPOSED IN 2018 CODE CHANGE CYCLE LISTED BY STANDARDS ORGANIZATION STAFF ANALYSES

Transcription

1 GROUP A NEW STANDARDS PROPOSED IN 2018 CHANGE CYCLE LISTED BY STANDARDS ORGANIZATION STAFF ANALYSES April 2, 2018 The following are comments by ICC staff regarding certain aspects of standards proposed to be referenced in the ICC Codes by code change proposals submitted for the 2018 Group A Proposed Changes. The comments relate to portions of the criteria for standards contained in Section 3.6 of CP#28 (see last page of this document). CHANGE ACCA STANDARDS RM7-18 IRC: M ANSI/ACCA 5 QI-2015 HVAC Quality Installation Specification M18-18 IMC: ANSI/ACCA 10 Manual SPS-2010 RA 2017 HVAC Design for Swimming Pools and Spas M70-18 RM31-18 IMC: IRC: M ANSI/ACCA 11 Manual Zr-2018 Residential HVAC System Zoning ANSI STANDARDS E2-18 IBC: ANSI A American National Test Method for Measuring Dynamic Coefficient of Friction of Hard Surface Flooring Materials M99-18 IMC: ANSI B Dryseal Pipe Threads FG21-18 IFGC: ANSI Z21.41/CSA Quick Disconnect Devices for Use with Gas Fuel Appliances F65-18 IFC: ANSI Z21.58/CSA Outdoor Cooking Gas Appliances FG21-18 IFGC: ANSI Z21.90 CSA Gas Convenience Outlets and Optional Enclosures Page 1 of 18 process Does not appear to require proprietary materials or agencies. Promulgation by a consensus process The standard appears to be a design guide or recommended practice document not intended to be enforceable Does not appear to require proprietary materials or agencies. Promulgation by a consensus process The standard was submitted in consensus draft form. The standard appears to be a design guide or recommended practice document not intended to be enforceable. Contains language that could affect enforceability. (Example(s) from the standard: Sections 8.2.6) Does not appear to require proprietary materials or agencies. Promulgation by a consensus process process process Currently referenced in the IFGC and the IRC. process

2 CHANGE F65-18 IFC: ANSI Z83.26/CSA Gas-Fired Outdoor Infrared Patio Heaters APSP STANDARDS SP14-18 ISPSC: ANSI/APSP/NPC/ICC American National Standard for the Plastering of Swimming Pools SP16-18 ISPSC: 316.2b ICC 902/APSP 902/SRCC Solar Pool and Spa Heating System F IFC: Table ASCE STANDARDS ASCE 7-16 Minimum Design Loads and Associated Criteria for Buildings and Other Structures F IFC: ASCE/SEI Tensile Membrane Structures ASHRAE STANDARDS RM8-18 IRC: M ANSI/ASHRAE Safety Standard For Refrigeration Systems And Designation And Classification Of Refrigerants M27-18 IMC: ASHRAE Method of Testing General Ventilation Air-Cleaning Devices for Removal Efficiency by Particle Size SP23-18 ISPSC: ASHRAE Ventilation for Acceptable Indoor Air Quality M33-18 RM25-18 RM26-18 IMC: IRC: M ASHRAE Ventilation and Acceptable Indoor Air Quality in Residential Buildings with Addenda b, d, k, l, g and s M20-18 IMC: ASHRAE Energy Standard for Buildings Except Low-rise Residential Buildings P80-18 IPC: ASHRAE Legionellosis: Risk Management for Building Water Systems P78-18 M12-18 IPC: IMC: ASHRAE Legionellosis: Risk Management for Building Water Systems (ANSI/ASHRAE Approved) Currently referenced in the IBC, IEBC and the IRC. Currently referenced in the IBC. Currently referenced in the IFC and the IMC. Currently referenced in the 2015 IgCC. Currently referenced in the IEBC, IECC-C; and the IMC. process Currently referenced in the IECC-C. The standard was submitted in consensus draft form. Page 2 of 18

3 CHANGE P P106-18, Part I P106-18, Part II P P109-18, Part I P109-18, Part II ASME STANDARDS IPC: , IRC: P , P ; Table P ASME A Plastic Push Fit Drain, Waste, and Vent (DWV) Fittings P30-18 IPC: ASME A M-1997 (R2017) Floor Affixed Supports for Off-the- Floor Plumbing Fixtures for Public Use RP14-18: IPC: P3201.3, P ASME A (R2014) In-Line Sanitary Waste Valves For Plumbing Drainage Systems M99-18 IMC: ASME B Unified Inch Screw Threads, (UN and UNR Thread Form) M99-18 IMC: ASME B1.13M-2006 Metric Screw Threads: M Profile M99-18 IMC: ASME B Dryseal Pipe Threads, Inch ASPE STANDARDS P IPC: ASPE/IAPMO/ANSI Z Test Method for Evaluating Roof Drain Performance ASSE STANDARDS P IPC: ASSE Performance Requirements for Positive Pressure Reduction Devices for Sanitary Drainage Systems P12-18 IPC: ASSE (R2011) Performance Requirements for Backflow Prevention Assembly Field Test Kits M99-18 IMC: ASSE Performance Requirements for Dielectric Pipe Unions process process process Currently referenced in the IPC. Page 3 of 18

4 CHANGE P97-18, Part I P97-18, Part II P45-18, Part I P45-18, Part II P48-18, Part I P48-18, Part II P49-18 P50-18, Part I P50-18, Part II P51-18 P59-18 P60-18 P61-18 P65-18 P66-18 P96-18 P35-18 P45-18, Part I P45-18, Part II P48-18, Part I P48-18, Part II P49-18 P50-18, Part I P50-18, Part II P51-18 P59-18 P60-18 P61-18 P65-18 P66-18 P96-18 P42-18 P96-18 IPC: Table 608.1, ASSE , Performance Requirements for IRC: Table Backflow Preventers with Integral P2902.3; Pressure Reducing Boiler Feed P , Valve and Intermediate P Atmospheric Vent Style for Domestic and Light Commercial IPC: 412.3, 412.5, , 419.5, 423.3, , IRC: P2708.4, P IPC: 408.3, 412.3, 412.5, ,419.5, 423.3, IRC: P2708.4, P IPC: 411.3, Water ASSE Performance Requirements for Water Heaters used as Temperature Control Devices for Hot Water Distribution Systems ASSE Performance Requirements for Water Heaters used as Temperature Limiting Devices ASSE Performance Requirements for Water Heaters for Emergency Equipment P IPC: 611.1, ASSE Performance Requirements for Commercial and Food Service Water Treatment Equipment Utilizing Drinking Water M M M P83-18 RM43-18 IMC: Table IPC: Table IRC: M ASTM STANDARDS ASTM A269/A269M-15a Seamless and Welded Austenitic Stainless Steel Tubing for General Service The standard was submitted in consensus draft form. The standard was submitted in consensus draft form. The standard was submitted in consensus draft form. The standard was submitted in consensus draft form. Page 4 of 18

5 CHANGE M M IMC: Table ASTM A Currently referenced in the IPC, IRC and Standard for Seamless, Welded, ISPSC. and Heavily Cold Worked Austenitic Stainless Steel Pipes P IPC: Table ASTM A518/A518M-99(2012) Corrosion-Resistant High Silicon Iron Castings M99-18 IMC: ASTM B Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube PSD2-18 IPSDC: ASTM C478-15a Specification for Circular Precast Reinforced Concrete Manhole Sections G IBC: ASTM C919-12(2017) Standard Practice for Use of Sealants in Acoustical Applications PSD2-18 IPSDC: ASTM C Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes P25-18 IPC: ASTM C Insulating Covers on Accessible Lavatory Piping M68-18 IMC: ASTM D Polyethylene Plastics Extrusion Materials for Wire and Cable M68-18 IMC: ASTM D Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds P103-18, Part I P103-18, Part II IPC: Table IRC: Table P ASTM D (2014) Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Composite Sewer Piping FS6-18 IBC: ASTM D (2011) Adhesives for Field-Gluing Plywood to Lumber Framing for Floor Systems SP11-18 ISPSC: ASTM D a(2012) Standard Practice for Visual Evaluation of Metamerism Currently referenced in the IPC, IPSDC and IRC. Contains language that could affect enforceability. (Example(s): Sections 1.1, 4.1, 6.1. Does not appear to require. Currently referenced in the IRC. Currently referenced in the IRC. Page 5 of 18

6 CHANGE FS96-18 IBC: , ASTM D Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter G IBC: Appendix P P101.1 ASTM D Standard Test Method for Determination of Formaldehyde and Other Carbonyl Compounds in Air (Active Sampler Methodology) FS IBC: ASTM D Insulated Vinyl Siding G IBC: ASTM E336-17a Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings G IBC: ASTM E Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures SP11-18 ISPSC: ASTM E (2015) Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry SP11-18 ISPSC: ASTM E a(2017) Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers FS96-18 IBC: ASTM E Standard Test Method for Room Test of Wall and Ceiling Materials and Assemblies WUIC9-18 WUIC10-18 WUIC14-18 IWUIC: , , , , ASTM E2632/E2632M-13e1 Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials FS3-18 IBC: ASTM E Standard Test Method for Behavior of Materials in a Tube Furnace with a Coneshaped Airflow Stabilizer, at 750 C WUI6-18 WUI12-18 IWUIC: 504.5, , , 505.5, ASTM E Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure Currently referenced in the 2015 IgCC. The 2013 edition of the standard is currently referenced in the IRC. The 2017 version proposed for reference here appears to be written in enforceable Contains language that could affect enforceability. (Example(s): Sections 1.3 and 8.4. Does not appear to require. Contains language that could affect enforceability. (Example(s): Sections , 4.4, 9.2, , , , Does not appear to require. is stated in the preface. is stated in the preface. Page 6 of 18

7 CHANGE FS30-18 IBC: 715.5, ASTM E Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies FS93-18 IBC: , ASTM E Manufactured Polymeric Drainage and Ventilation Materials Used to Provide a Rainscreen Function F93-18 IFC: ASTM E Standard Test Methods for Determining the Effectiveness of Fire Retardant Treatments for National Christmas Trees P115, Part I IPC: ASTM Folded Poly (Vinyl Chloride) (PVC) for Existing Sewer and Conduit Rehabilitation G72-18 IBC: ASTM F (2012) Standard Test Methods for Detention Locks for Swinging Doors P115, Part I IPC: ASTM F Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation P IPC: ASTM F Standard Practice for Rehabilitation of a Sewer Service Lateral and its Connection to the Main Using a One Piece Main and Lateral Curedin Place Liner P IPC: ASTM F Standard Practice for The Sectional Repair of Damaged Pipe by Means of an Inverted Cured-in- Place Liner P IPC: Table ASTM F Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems M IMC: Table ASTM F Chlorinated Poly (Vinyl Chloride)/Aluminum/Chlorinated Poly (Vinyl Chloride) (CPVC-AL- CPVC) Composite Pressure Tubing P IPC: ASTM F Standard Practice for Installation of an Outside Sewer Service Cleanout through a Minimally Invasive Small Bore Vacuum Excavation is stated in the preface. Currently referenced in the IRC. Currently referenced in the IRC. Currently referenced in the IPC. Page 7 of 18

8 CHANGE M M P86-18 P87-18, Part I P87-18, Part II P IPC: ASTM F Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long Term Watertightness of Cured-in Place Rehabilitation of Main and Lateral Pipelines M IMC: Table ; Table S17-18 S18-18 IMC: Table ASTM F3226/F3226M-16 IPC: Table Metallic IRC-P: Table Press-Connect Fittings for Piping P and Tubing Systems IBC: , ASTM F Crosslinked Polyethylene (PEX) Tubing with Oxygen Barrier for Hotand Cold Water Hydronic Distribution Systems ASTM WK Standard Practice for the On-Site Inspection of Installed Fire Resistive Materials M IMC: ASTM FXXX-WK60062 New Polyethylene of Raised Temperature/Aluminum/Polyethyle ne of Raised Temperature (PE- RT/AL/PE-RT) Composite Pressure Pipe process ASTM standards follow a consensus process. Appears to be written in enforceable language. Does not appear to require process The Standard was submitted in consensus draft form. BHMA STANDARDS E65-18 IBC: ANSI/BHMA A Exit Devices E60-18 IBC: ANSI/BHMA A Delayed Egress Locking Systems E54-18 IBC: ANSI/BHMA A Standard For Door Hardware Single Motion to Egress G IBC: Appendix P P101.1, P103.1, P104.1, P105.1, P106.1, P107.1 CALIFORNIA DEPARTMENT OF PUBLIC HEALTH (CDPH) CDPH/EHLB/Standard Method V 1.2-January 2017 Standard Method for the Testing and Evaluation of Volatile Organic Chemical emissions from Indoor Sources Environmental Chambers 1.2 Page 8 of 18 Currently referenced in the 2015 IgCC.

9 CHANGE CALIFORNIA ENVIRONMENTAL PROTECTION AGENCY- AIR RESOURCE BOARD G IBC: Appendix P P104.1 California Air Resources Board, Suggested Control Measures for Architectural Coatings, February 1, 2008 CSA and CSA AMERICA STANDARDS FG21-18 IFGC: ANSI Z21.41/CSA Quick Disconnect Devices for Use with Gas Fuel Appliances FG21-18 IFGC: ANSI Z21.90 CSA Gas Convenience Outlets and Optional Enclosures M RM36-18 RM37-18 RM38-18 IMC: Table , Table , ; Table M2105.4, M2105.4, M ANSI/CSA/IGSHPA C448 Series- 16 Design and Installation of Earth Energy Systems F20-18 IFC: CSA/ANSI NGV Compressed natural gas vehicle fuel containers F IFC: CSA/ANSI NGV Residential Fueling Appliances FG22-18 IFGC: CSA/ANSI NGV F IFC: , Vehicle Fueling Appliances (VFA) PSD1-18 IPSDC: CSA B66-16 Design, Material, And Manufacturing Requirements For Prefabricated Septic Tanks And Sewage Holding Tanks F IFC: CSA B NGV Maintenance Facilities Code P131-18, Part I P131-18, Part II P132-18, Part I P132-18, Part II IPC: IRC: P CSA B805-17/ICC Rain Harvesting System Currently referenced in the 2015 IgCC. process process Currently referenced in the IMC and the IRC. process Currently referenced in the IFGC. process process The Standard was submitted in consensus draft form. DEPARTMENT OF HOMELAND SECURITY -INFRASTRUCTURE SECURITY COMPLIANCE DIVISION (DHS) STANDARDS F IFC: Appendix H H CFR Part Chemical Facility Anti-Terrorism (CFATS) Page 9 of 18 Does not indicate promulgation by a consensus process as it is a federal regulation.

10 CHANGE DEPARTMENT OF JUSTICE (DOJ) G IBC: ADA with Disabilities Act Title III Regulations, Part 36, Subpart C Auxiliary Aids and Services. G IBC: Appendix P P101.1 F10-18 IFC: , , EPA STANDARDS USEPA Method TO-17 Issued 1/1999 Determination of Volatile Compounds in Ambient Air Using Active Sampling on to Sorbent Tubes FM STANDARDS FM Containers for Combustible Waste IAPMO STANDARDS P IPC: IAPMO PS Airgap Units for Water Conditioning Equipment Installation PSD1-18 IPSDC: IAPMO IGC Corrugated Thermoplastic Tanks PSD1-18 IPSDC: IAPMO/ANSI Z Prefabricated Septic Tanks P IPC: ASPE/IAPMO/ANSI Z Test Method for Evaluating Roof Drain Performance ICC STANDARDS SP13-18 ISPSC: ICC A Accessible and Usable Buildings E34-18 E E E E E E G SP16-18 IBC: , , , , , , , ISPSC: Table 316.2(2) and Facilities ICC A Accessible and Usable Buildings and Facilities. ICC 902/APSP 902/SRCC Solar Pool and Spa Heating System Does not indicate promulgation by a consensus process. Contains language that could affect enforceability. (Example(s): Sections 2.4.6, 3.4, 3.6, 5.14, Does not appear to require Does not indicate promulgation by a consensus process. language. Appears to require proprietary agencies. (See Section 2.3). Does not indicate promulgation by a consensus process. language. The standard appears to be a design guide or recommended practice document not intended to be enforceable. Does not appear to require proprietary materials or agencies. Does not indicate promulgation by a consensus process. Does not indicate promulgation by a consensus process. Currently referenced in the IBC, IEBC, IFC, IPC, IRC and IZC. Page 10 of 18

11 CHANGE PM8-18, Part I PM8-18, Part II IPMC: 310.2, ICC Currently referenced in the IBC and IRC , ICC/NSSA Standard for the Design IFC: 320 ; and Construction of Storm Shelters 320.3; P131-18, Part I P131-18, Part II P132-18, Part I P132-18, Part II IPC: IRC: P FS IBC: M RM36-18 RM37-18 RM38-18 CSA B805-17/ICC Rain Harvesting System ICC Consensus Draft-January 2018 Developed following an ANSI process. INTERNATIONAL GROUND SOURCE HEAT PUMPS ASSOCIATION (IGSHPA) IMC: Table , Table , ; Table M2105.4, M2105.4, M ANSI/CSA/IGSHPA C448 Series- 16 Design and Installation of Earth Energy Systems Currently referenced in the IMC and the IRC. INTERNATIONAL INSTITUTE OF AMMONIA REFRIGERATION (IIAR) F76-18 IFC: ANSI/IIAR Maintenance and Inspection of Closed-circuit Ammonia Refrigerated Systems F78-18 IFC: ANSI/IIAR Standard for Recognized and Generally Accepted Good Engineering Practices (RAGAGEP) for Existing Closed-circuit Ammonia Refrigeration Systems G IBC: Table (3) G IBC: ; Table (3) ISO STANDARDS ISO Series 1 freight containers- Classification, dimensions and ratings ISO Series 1 freight containers- Specification and Testing- Part 1: General cargo containers for general purposes G IBC: ISO Freight containers-coding Identification and marking- Amendment G IBC: Appendix P P101.1 G IBC: Appendix P P101.1 ISO/IEC General Requirements for the competence of testing and calibration laboratories ISO/IEC Conformity assessment- Requirements for bodies certifying products, processes and services. process The Standard was submitted in consensus draft form. process The Standard was submitted in consensus draft form. Is promulgated by a consensus process. Is promulgated by a consensus process. Is promulgated by a consensus process. Currently referenced in the 2015 IgCC. Currently referenced in the 2015 IgCC. Page 11 of 18

12 CHANGE F262-18, Part II IBC: F IFC: 911.1, 911.4; Table ; IBC:[F] Table F IFC: , , , , , F IFC: Table NFPA STANDARDS NFPA Standard for Fire and Explosion Prevention during Cleaning and Purging of Flammable Gas Piping Systems NFPA Standard on Explosion Protection by Deflagration Venting NFPA Standard for the Fire Protection of Telecommunications Facilities NFPA Recommended Practice on Static Electricity M31-18 IMC: NFPA Health Care Facilities Code F IFC: Table NFPA Standard on Fire and Life Safety in Animal Housing Facilities F IFC: NFPA Standard for the Protection of Records F262-18, Part II IBC: ; , F267-18, Part I F267-18, Part II G F IFC: , IBC: IFC: F IFC: Appendix O O101.2; O101.3; O101.4 F IFC: Appendix O O101.1 NFPA Standard for Safeguarding Construction, Alteration, and Demolition Operations NFPA Standard Method of Fire Tests for the Evaluation of Thermal Barriers NFPA Standard for the Installation of Lightning Protection Systems NFPA Standard for Professional Qualifications for Fire Inspector and Plan Examiner NFPA Standard on Fire Marshal Professional Qualifications NSF STANDARDS PSD5-18 IPSDC: NSF Evaluation of Components and Devices used in Wastewater Treatment Systems Page 12 of 18 Currently referenced in the IFC. process process process Currently referenced in the IBC, IEBC, IFC, and IPC. process process Currently referenced in the IFC. Currently referenced in the IBC and IRC.. language. Does not appear to require proprietary materials or agencies. Promulgation by a consensus process process

13 CHANGE P IPC: NSF Ultraviolet Microbiological Water Treatment Systems RP12-18 IRC: P NSF Currently referenced in the IPC. Drinking Water Distillation Systems PSD1-18 PSD5-18 PSD1-18 PSD5-18 M RM40-18 M RM39-18 IPSDC: ; ; ; ; IPSDC: , , IMC: Table , Table IRC: Table M2105.4, Table M IMC: Table , Table IRC: Table M2105.4, Table M NSF Wastewater Treatment Systems- Nitrogen Reduction NSF Onsite Residential and Commercial Water Reuse Treatment Systems NSF Cross-linked polyethylene (PEX) pipe and fittings for water-based ground-source (geothermal) heat pump systems NSF Polyethylene of raised temperature (PE-RT) pipe and fittings for waterbased ground source (geothermal) heat pump systems P IPC: NSF Drinking Water Temperature Units- Emerging Compounds/Incidental Contaminants Currently referenced in the IPC and IRC. process process PCI STANDARDS FS77-18 IBC: PCI Specification for Fire Resistance of Precast/Prestressed Concrete SCAQMD STANDARDS G IBC: Appendix P P103.1 RULE Adhesive and Sealant Applications with amendments through January 7, 2005 Currently referenced in the IBC under a previous number. Currently referenced in the 2015 IgCC. SMACNA STANDARDS M69-18 IMC: ANSI/SMACNA Thermoset FRP Duct Construction Manual-2 nd Edition M68-18 IMC: 603.8, SMACNA 2 nd Edition-1995 Thermoplastic Duct PVC Construction Manual Does not appear to require proprietary materials or agencies. Promulgation by a consensus process The standard appears to be a design guide or recommended practice document not intended to be enforceable. Does not appear to require proprietary materials or agencies. Promulgation by a consensus process The standard appears to be a design guide or recommended practice document not intended to be enforceable. Page 13 of 18

14 CHANGE PSD5-18 STANDARDS COUNCIL OF CANADA IPSDC: E2-18 IBC: , CAN/BNQ Onsite Residential Wastewater Treatment Technologies Technologies including Modification 1 dated March 16, 2017 TCNA STANDARDS ANSI A American National Test Method for Measuring Dynamic Coefficient of Friction of Hard Surface Flooring Materials UL STANDARDS G34-18 IBC: UL 10D-2017 Standard for Fire Test of Fire Protective Curtain Assemblies G IBC: M95-18 IMC: Table UL 96A-2016 Standard for Installation Requirements for Lightening Protection Systems UL Tube Fittings for Flammable and Combustible Fluids, Refrigeration Service and Marine Use E3-18 IBC: UL Standard for Slip Resistance of Floor Surface Materials M95-18 IMC: Table UL Standard for Refrigerating Units F63-18 IFC: UL Steel Auxiliary Tanks for Oil Burner Fuel (with revisions through March 8, 2013) M95-18 IMC: Table M88-15 M95-18 IMC: Table ; UL Standard for Dehumidifiers UL Standard for Room Air Conditioners Page 14 of 18 Contains language that could affect enforceability. (Example(s) from the standard: Sections 8.2.6). Does not appear to require proprietary materials or agencies. Promulgation by a consensus process process Contains language that could affect enforceability. (Example(s) from the standard: Sections 1.4, 4.4.1, 5.2) Appears to require agencies. The test must be done by a James Machine. It is not clear if this machine is offered by more than one company. (Example(s) from the standard: Section 4.2.1, 4.2.4, 4.2.5, 4.3.2) Does not indicate promulgation by a consensus process. process process process process

15 CHANGE F72-18 IFC: UL 498A-08 Current Taps and Adapters with revisions thru June 10, 2016 process M88-18 IMC: UL Standard for Refrigerated Vending Machines FS IBC: UL 723S-2006 Drop-Out Ceilings Installed Beneath Automatic Sprinklers F66-18 IFC: UL Residential Incinerators-with revisions through November 2014 F IFC: ; Table UL 971A-2006 Outline of Investigation for Metallic Underground Fuel Pipe E56-18 IBC: UL Standard for Burglary-Resistant Electric Mechanisms-with revisions through 2015 F73-18 IFC: UL 1363A-2014 Outline of Investigation for Special Purpose Relocatable Power Taps M F IMC: IFC: Table UL Aboveground Piping Requirements M85-18 IMC: UL Unvented Alcohol Fuel Burning Decorative Appliances with revisions through March 25, 2016 F IFC: UL Plant Extraction Units F F IBC-FS: IFC: , UL Fire Resistant Pipe Protection Systems Carrying Combustible Liquids process Currently referenced in the IMC. This is an outline only and not a standard. Does not indicate promulgation by a consensus process. process This is an outline only and not a standard. Does not state that it is promulgated according to a consensus procedure. The standard was submitted in consensus draft form. process This is an outline only and not a standard. Does not state that it is promulgated according to a consensus procedure. Page 15 of 18

16 CHANGE F IFC: UL Evaluation for Re-purposing Batteries The Standard was submitted in consensus draft form. M88-18 IMC: UL Heating and Cooling Equipment with revisions through July 2015 Currently referenced in the IRC, IMC and ISPSC. F22-18 IFC: UL Factory Automation Equipment F IFC: UL Standard for Tests for Determining Carbon Monoxide (CO) Emission Rate of Portable Generators F48-18 IFC: UL Outline of Investigation for In- Building 2-way Emergency Radio Communication Enhancement Systems, 2018 M52-18 IMC: UL Outline of Investigation for Pollution Control Units for Commercial Cooking F IFC: 202, , , UL 9540A-2017 UL Standard for Safety Test Method for Evaluating Thermal Runaway Fire Propagation in Battery Energy Storage M88-18 IMC: UL Household and Similar Electrical Appliances-Safety-Part 2-24: Particular Requirements for Refrigerating Appliances, Ice- Cream Appliances and Ice-Makers M86-18, Part I M86-18, Part II M88-18 SP17-18 M86-18, Part I M88-18 IMC: Table 1102 IRC: M ISPSC: Table IMC: Table 1102 UL Standard for Safety for Household and Similar Electrical Appliances- Safety-Part 2-40: Particular Requirements for Electrical Heat Pumps, Air-Conditioners and Dehumidifiers UL/CSA Household and Similar Electrical Appliances-Safety-Part 2-89: Particular Requirements for Commercial Refrigerating Appliances with an Incorporated or Remote Refrigerant Unit or Compressor This is an outline only and not a standard. This is an outline only and not a standard. Does not indicate promulgation by a consensus process. not process Currently referenced in the IRC. Page 16 of 18

17 CHANGE SP13-18 ISPSC: UL Standard for Household and Similar Electrical Appliances: Particular Requirements for Electrically Powered Pool Lifts, with Revisions through September 29, F73-18 IFC: UL Medical Electrical Equipment, Part i: General Requirements for Safety 2003 F22-18 IFC: UL Information Technology Equipment Safety Requirements F22-18 IFC: UL Audio/Video, Information and Communication Technology Equipment-Safety Requirements 3.6 Referenced Standards: In order for a standard to be considered for reference or to continue to be referenced by the Codes, a standard shall meet the following criteria: Code References: The standard, including title and date, and the manner in which it is to be utilized shall be specifically referenced in the Code text The need for the standard to be referenced shall be established Standard Content: A standard or portions of a standard intended to be enforced shall be written in mandatory language The standard shall be appropriate for the subject covered All terms shall be defined when they deviate from an ordinarily accepted meaning or a dictionary definition The scope or application of a standard shall be clearly described The standard shall not have the effect of requiring proprietary materials The standard shall not prescribe a proprietary agency for quality control or testing The test standard shall describe, in detail, preparation of the test sample, sample selection or both The test standard shall prescribe the reporting format for the test results. The format shall identify the key performance criteria for the element(s) tested The measure of performance for which the test is conducted shall be clearly defined in either the test standard or in Code text The standard shall not state that its provisions shall govern whenever the referenced standard is in conflict with the requirements of the referencing Code. Page 17 of 18

18 The preface to the standard shall announce that the standard is promulgated according to a consensus procedure Standard Promulgation: Code change proposals with corresponding changes to the code text which include a reference to a proposed new standard or a proposed update of an existing referenced shall comply with this section Proposed New Standards. In order for a new standard to be considered for reference by the Code, such standard shall be submitted in at least a consensus draft form in accordance with Section 3.4. If the proposed new standard is not submitted in at least consensus draft form, the code change proposal shall be considered incomplete and shall not be processed. The code change proposal shall be considered at the Committee Action Hearing by the applicable code development committee responsible for the corresponding proposed changes to the code text. If the committee action at the Committee Action Hearing is either As Submitted or As Modified and the standard is not completed, the code change proposal shall automatically be placed on the Public Comment Agenda with recommendation stating that in order for the public comment to be considered, the new standard shall be completed and readily available prior to the Public Comment Hearing. If the committee action at the Committee Action Hearing is Disapproval, further consideration on the Public Comment Agenda shall include a recommendation stating that in order for the public comment to be considered, the new standard shall be completed and readily available prior to the Public Comment Hearing Update of Existing Standards. Code change proposals which include technical revisions to the code text to coordinate with a proposed update of an existing referenced standard shall include the submission of the proposed update to the standard in at least a consensus draft form in accordance with Section 3.4. If the proposed update of the existing standard is not submitted in at least consensus draft form, the code change proposal shall be considered incomplete and shall not be processed. The code change proposal, including the update of the existing referenced standard, shall be considered at the Committee Action Hearing by the applicable code development committee responsible for the corresponding changes to the code text. If the committee action at the Committee Action Hearing is either As Submitted and As Modified and the updated standard is not completed, the code change proposal shall automatically be placed on the Public Comment Agenda with the recommendation stating that in order for the public comment to be considered, the updated standard shall be completed and readily available prior to the Public Comment Hearing. If the committee action at the Committee Action Hearing is Disapproval, further consideration on the Public Comment Agenda shall include a recommendation stating that in order for the public comment to be considered, the updated standard shall be completed and readily available prior to the Public Comment Hearing. Updating of standards without corresponding code text changes shall be accomplished administratively in accordance with Section The standard shall be developed and maintained through a consensus process such as ASTM or ANSI. Page 18 of 18