Water alarm. Water detection system L-PS-X / LS-X. Højmevej Odense SV Tlf Fax
|
|
- Constance Anderson
- 5 years ago
- Views:
Transcription
1 Water alarm Water detection system L-PS-X / LS-X Program release Højmevej Odense SV Tlf Fax Doc. no rev
2 Table of contents Table of contents... 1 System description... 3 Components... 3 Option... 3 Indicators and controls... 4 Reset button... 4 Terminals... 5 Supply:... 5 Alarm output:... 5 Sensor attachment:... 5 Function... 6 Sensor location... 6 Applications... 6 Remote Communication via PC... 7 Note!... 7 Configuration abstract... 7 Activation of measuring channel... 7 Logger... 8 Setting the clock... 9 Mark... 9 Baud rate Danish letters Networking Appendix Drawing Liquid Sensor - Space under roof slope. Drawing Liquid Sensor in floor duct. Drawing Liquid Sensor under pipe joint. Drawing Liquid Sensor - Crawl space Release Doc.no rev Page 2
3 System description DanTaet Water alarm L-PS-X System is designed for monitoring sensitive areas for aggregation of water using up to eight liquid sensors type LS-X. L-PS-X features a fail-safe floating alarm output, and a floating auxiliary alarm output. By series connecting their alarm outputs, several L-PS-X may be cascaded to operate on a single CTS-input. The LS-X liquid sensors feature a 2-wire current interface, permitting remote location (up to 3,500 meters) of the sensors from L-PS-X, provided a properly shielded cable of a suitable cross-section is employed. The liquid sensors respond to an aggregation of water large enough to touch both its electrodes, causing the L-PS-X to issue an alarm according to the selected mode. L-PS-X will further issue alarms for system, sensor and cable failures. Each of the eight measuring channels may be configured: Channel On/Off (unused channels must be Off) (ENA) Alarm response time 1 or 1800 seconds (drying time) (DLY) Channel autoreset On/Off (response if aggregate water disappears) (RST) Further, the lower eight bits of the DCB device address may be set on a switch. Components The system comprises a controller type L-PS-X and a number of liquid sensors type LS-X. Option The controller may optionally be equipped with a RS-232 interface for terminals, serial printers or CTS-systems, or a RS-485 interface for the DCB when a master DanTaet WLP controller is involved Release Doc.no rev Page 3
4 Indicators and controls A power lamp indicates all primary and secondary power supplies are OK. The front panel features a Reset button used for muting the acoustic alarm, and to acknowledge alarms and restart the system. Further, each channel features a status lamp indicating: No light: Fixed green light: Fixed yellow light: Fixed red light: Blinking red light: Channel is switched Off Channel sensor is dry. Channel sensor is wet, alarm response time not expired. Channel issued an alarm after response time expiry. Channel issued a water alarm, and the acoustic alarm has been muted. Blinking green light: Cable break or no sensor attached (system error). (Alarm will occur within 10 sec.) Green/red alternate: Sensor- or cable short, relay or sensor voltage failure (System error). (Alarm will occur within 10 sec.) Blinking yellow light: Channel issued a system alarm, and the acoustic alarm has been muted. Reset button The front panel Reset button is used for muting the acoustic alarm and for alarm acknowledgement and system restart. Function: The first key press mutes the acoustic alarm; system remains in alarm state. Second key press will acknowledge alarm and restart system. If the root cause of the alarm persists, the system will eventually re-enter the alarm state Release Doc.no rev Page 4
5 Terminals Stik til interface Kanal 1 Kanal 2 Kanal 3 Kanal 4 Kanal 5 Kanal 6 Kanal 7 Kanal 8 Vex +Vs Vex +Vs Vex +Vs Vex +Vs Vex +Vs Vex +Vs Vex +Vs Vex +Vs 230 Vac GND L N 200mAT 200mAT Supply: Alarm output: 230 Vac Terminal 1 Protective Earth Terminal 2 Live Terminal 3 Neutral 3 sets floating SPDT switch Main alarm Main alarm Aux alarm Output 1 (230V) Output 2 (24V) Output 3 (24V) Terminal 4 NC Terminal 7 NC Terminal 10 NC Terminal 5 C Terminal 8 C Terminal 11 C Terminal 6 NO Terminal 9 NO Terminal 12 NO Sensor attachment: Ch. 1 Terminal 13 Minus (white) Ch. 5 Terminal 21 Minus (white) Terminal 14 Plus (brown) Terminal 22 Plus (brown) Ch. 2 Terminal 15 Minus (white) Ch. 6 Terminal 23 Minus (white) Terminal 16 Plus (brown) Terminal 24 Plus (brown) Ch. 3 Terminal 17 Minus (white) Ch. 7 Terminal 25 Minus (white) Terminal 18 Plus (brown) Terminal 26 Plus (brown) Ch. 4 Terminal 19 Minus (white) Ch. 8 Terminal 27 Minus (white) Terminal 20 Plus (brown) Terminal 28 Plus (brown) Use shielded 2x0.25 mm 2 cable for sensor extension. Be sure the to clamp the shield firmly under one of the mounting plate brackets. Maximum allowable total cable length per sensor is 3,500 meters (11,400 ft) Release Doc.no rev Page 5
6 Function In the normal state, each activated measuring channel is monitored for cable break, cable short and aggregate water conditions. Cable break and short alarms always employ a 10 second response time, whereby during installation channels may be switched on briefly to check the channel status in the indicator without causing an immediate alarm. Aggregate water alarm is issued with the response time selected for the channel, 1 or 1800 seconds, i.e. for practical purposes immediately, or with a half-hour delay. Note that the error condition must be present continuously during the response time interval for the system to issue an alarm. In the normal state, the alarm relay is activated. On alarm, the main alarm outputs are deactivated, while the auxiliary alarm output and the acoustic alarm are activated. The acoustic alarm may be muted by pressing the front panel Reset button; at the same time the auxiliary alarm output will deactivate, and channel lamps indicating an error will switch from fixed to blinking red light (aggregate water), or from blinking red/green to blinking yellow light (cable/sensor error). After muting the acoustic alarm, finding and mending the error and wiping the sensor dry, the system is restarted by pressing the Reset button once again, whereby the main alarm output is activated if all active channels are error-free. If channel Autoreset is selected, aggregate water alarms for that channel will be automatically revoked after the aggregate water has vanished, provided the minimum alarm time of 10 seconds has expired. L-PS-X handles multiple nested alarms in the alarm state. If the acoustic alarm has been muted, it will be turned back on if another channel issues a new alarm. New alarms are indicated by fixed red, or alternating red/green light. If any channel indicator displays this, at least two Reset key presses will be required to reactivate the alarm relay. Sensor location Location of individual liquid sensors should be determined by a risk assessment strategy contemplating where water ingress is likely to occur, and where the risk/effect of leakage is particularly profound. Note that a minimum separation of 1 metre (3 ft) is required between any two liquid sensors likely to be in contact with the same water aggregate. Applications Enclosed in this manual are suggestions and examples for sensor location Drawings , , , Release Doc.no rev Page 6
7 Remote Communication via PC If the L-PS-X control box is ordered with RS-232 interface, and connecting this to the COM port of a PC, system status and alarms may be tracked/monitored with the use of a terminal program (e.g. Hyperterminal on Windows). Manual communication with the control box is also possible using the following commands: Function Command Setting the clock rtc Alarm acknowledge rst System status mark Naming channels loc n Note! When an alarm is acknowledged using the rst command, the system status should be checked using the mark command to inspect if any channel is still in an alarm condition. The rtc, mark and loc commands are described further on in this manual. Configuration abstract Configuration of controller functionality and communication is done using a series of miniature switches located inside the front panel cover of the L-PS-X controller. The switches control the following functions: ENA = Activation/deactivation of individual measuring channels. DLY = Alarm response time for channel. Off = 1 sec / On = 1800 sec. RST = Channel autoreset. On = Alarm is revoked when water disappears. CID = Controller address (lower 8 bits). Used by DCB networking. AUX = Logger setup. Activation of measuring channel For the controller to employ an attached liquid sensor, the channel must be activated on the ENA switch. ENA switch 1-8 (Ch 1-8) Off/On = Channel deactivated/activated Release Doc.no rev Page 7
8 Logger The COM port serving the resident system monitor may also be employed for event logging on an attached computer, serial terminal or serial printer. The AUX switch is used to govern the characteristics of the event logging feature. AUX switch no. 3 Off/On = Logging Off/On Event logging comes in two fundamentally different ways. One way ('Terse') is intended for reception by a computer, such as e.g. a CTS system. The other way ('Verbose') is meant for observation by the human eye, on a terminal screen or printer. Terse logging employs just one message type, with a consistent format: a) Relay status indicator +/a/q = OK/Alarm/Quiet (muted) b) Real time i the format <wdyyyymmdd,hhmmss.ffff> where wd is a two-letter weekday abbreviation. c) Input status indicators w. index i1-i8 -/+/b/w/c/f = Off/OK/break/wet/current/fail d) Monitor status indicators w. index m1-m8 +/a/q = OK/Alarm/Quiet e) CR/LF Verbose logging employs a system text and a user definable text up to 54 characters for description/identification of the measuring point for the channel. Message length thus depends on the length of the user-defined text. Messages are composed thus: a) Real time formatted as: wdy dd-mm-yyyy hh:mm:ss.ffff b) Colon and space c) Event: Alarm/Quiet/Reset d) Channel number (1-8) e) User text for channel f) CR/LF AUX switch no. 4 Off/On = Terse/Verbose message format Release Doc.no rev Page 8
9 User text entry is done from a terminal attached to the unit COM port. Press <Enter> to obtain a prompt > or *, then use the command: loc n This is the user text for channel n to enter the user text for channel n (n=1..8), or loc n to inspect the user text for channel n (n=1..8) Setting the clock Setting the system real-time clock is likewise done from a terminal attached to the controller COM port. At the prompt, issue rtc to inspect the current clock setting, and the command rtc wdy dd-mm-yyyy hh:mm:ss[.ffff] to change it. Note that the weekday specification (wdy) employs the English three-letter abbreviations sun mon tue wed thu fri sat (it is sufficient to enter the first two letters), and that entry of subsecond time specification [.ffff] is optional. Mark For continuous verification of functionality, the controller may be setup to log a mark every 10 minutes. In terse mode, this mark will have the same format as all other terse messages. In verbose mode, the format is: a) Real time formatted wdy dd-mm-yyyy hh:mm:ss.ffff b) Colon and space c) The string -Markd) CR/LF AUX switch no. 5 Off/On = Mark Off/On Release Doc.no rev Page 9
10 Baud rate The COM port may operate at two speeds, or baud. AUX switch no. 6 Off/On = /9.600 baud. Danish letters Danish letters may be employed in the user texts, provided these are entered from a terminal using either DOS (cp 850/865), 7-bit ISO ore 8-bit ISO character sets. AUX switches nos. 1 and 2 select the character set used to write Danish letters to the COM port, regardless of which character map was used for input. If Danish letters will not be used, AUX switches 1 and 2 should probably be left in the Off position to avoid remapping of ISO-7 symbols [ \ ] { }. AUX switches nos. 1 and 2 govern: aux1 aux2 æ ø å Æ Ø Å OFF OFF < no translation > none OFF ON $91 $9B $86 $92 $9D $8F DOS ON OFF $7B $7C $7D $5B $5C $5D ISO-7 ON ON $E6 $F8 $E5 $C6 $D8 $C5 ISO Release Doc.no rev Page 10
11 Networking Several L-PS-X units equipped with RS-485 interface may be connected to a master controller which can address and hence communicate with each unit separately. When units are networked, automatic logging must be disabled, and Terse selected. The networking protocol solely implements commands 'MARK' and 'RST' for master controller usage. When L-PS-X is addressed with the MARK command, it will return a normal status line. When addressed with the RST command, alarms are reset and monitoring is restarted. An L-PS-X address consist of a segment number (0-255) and a host ID (1-254). The unit address may be inspected from a terminal attached to the COM port using the command CID Which will display the controller ID (decimal) seg.hid. The segment number may be changed using the command SEG nnn while the host ID is selected on the CID switch. Switch 1 = bit 0 etc. The networking protocol is line oriented. Each line starts with a header, proceeds with a command, and ends with CR/LF. A datagram consists of one or more such lines, terminated by > or * followed by 100 msec of inactivity. A header consists of:?tttt!ssss.!tttt?ssss. for a query, and for a response, where tttt and ssss are 4-digit hexadecimal addresses for 'target' (recipient) and 'source' (originator) respectively. A segment controller may broadcast to all network hosts by issuing the datagram for target $xxff (broadcast). No host may respond to a broadcast Release Doc.no rev Page 11
12
13
14
15
MO n : 12JMC rév A
CTT8 MO n : rév A Page 2 / 18 MODIFICATIONS Rev. Description Date Checked by Approuved by Z Creation 2012/02/12 JMC LA A First issue 2012/02/14 JMC LA INDEX Page 3 / 18 GENERALITY 4 INTRODUCTION 4 ACCESSORIES
More informationCTT8 TEMPERATURE MONITOR DEVICE
INSTRUCTION MANUAL IM302-U v2.3 CTT8 TEMPERATURE MONITOR DEVICE GENERALITY The device of control temperatures CTT8 is used in the control of electric machine, transformer, motor, etc. where it s possible
More informationSyringeHeater.com. Syringe Heater. Thermo-Kinetic Heat Clamping. Model: HEATER-KIT-1LG HEATER-KIT-5SP
SyringeHeater.com SyringePump.com Syringe Heater Thermo-Kinetic Heat Clamping Model: HEATER-KIT-1LG HEATER-KIT-5SP CAUTION RISK OF ELECTRIC SHOCK CAUTION: SURFACE OF HEATING PADS WILL GET VERY HOT WARNING
More informationReplaceable LED modules. Sleep or unattended mode. Auto-silence and auto-acknowledge
Replaceable LED modules 11 Alarm Sequences as per ISA-18.1 standard Each channel/window fully field programmable RS232 or RS485 MODBUS-RTU communication Repeat relay for each window and multifunction relays
More informationDatabase for CTS6000 MODBUS
Database for CTS6000 MODBUS Valid for: LONcard SW1.7.4B, Variable List V2.02 Version 1.08-4, 01-05-2016 Contents Contents... 2 1. Installation... 3 1.1. Installation and operating instructions... 3 2.
More informationP2267 NETWORK INTERFACE
P2267 NETWORK INTERFACE USER MANUAL FOR OPERATING SYSTEMS: 22031-03 23636-01 October 2009 Associated Controls (Australia) Pty. Limited 2-4 Norfolk Road Greenacre, NSW, 2190. PH +61 2 9642 4922, FAX +61
More informationEIA-232D Protocol And Data Formats for the AFP-200 Fire Alarm Control Panel
12 Clintonville Road Northford, CT 06472 TEL (203) 484-7161 FAX 203.484.7718 EIA-232D Protocol And Data Formats for the AFP-200 Fire Alarm Control Panel DOCUMENT # 50078 05/18/94 REV: A P/N 50078:A ECN
More informationM1000 Alarm Annunciator
Data Sheet Alarm Annunciator Reliable Supervision and Control 10 inputs with LED indications Supports both NO/NC input contacts 10 open collector outputs Built-in siren relay Text label for alarm descriptions
More informationModel: Slimline-N. 1 Slimline Series
Model: Slimline-N Model: Slimline-N 1 Slimline Series Table of Contents Product Image Table of Contents What is a Programmable Room Thermostat? Installation Procedure LCD Display Operating Mode Setting
More informationTPOne-B. Electronic Programmable Room Thermostat. Installation Guide. Danfoss Heating
TPOne-B Electronic Programmable Room Thermostat Danfoss Heating Installation Guide TPOne is an intelligent programmable heating control made easy. TPOne includes features which are designed to save energy.
More informationLaptop / PC Programming Manual
Laptop / PC Programming Manual Doc. # Fire PC Program rev B 01.07 This Document is property of Evax Systems, Inc. The Evax Fire Solutions Programmer Components 2 1.0 System Setup 4 1.1 Interface Setup
More informationNGC-UIT2 MODBUS PROTOCOL INTERFACE MAPPING FOR NGC-30 SYSTEMS. Firmware versions up to V2.0.X
NGC-UIT2 MODBUS PROTOCOL INTERFACE MAPPING FOR NGC-30 SYSTEMS Firmware versions up to V2.0.X INDUSTRIAL HEAT TRACING SOLUTIONS EN-RaychemNGCUIT2Protocol-IM-H57880 06/15 1/32 Contents Section I Introduction
More informationSM3000 Videographic Recorder. User Guide. Modbus (RTU) Communications Option
SM3000 Videographic Recorder User Guide (RTU) Communications Option ABB The Company We are an established world force in the design and manufacture of instrumentation for industrial process control, flow
More informationUser Manual. Dryer Controller M720
User Manual Dryer Controller M720 Hardware version 1.00 Software version 1.00 Preliminary version Manual M720 Dryer controller Page 1 of 42 Document history Preliminary version: - Created in April, 2009
More informationREPEATER FS5200R INSTRUCTION MANUAL
REPEATER FS5200R INSTRUCTION MANUAL Instruction Manual Page1 CONTENTS 1. Introduction... 3 2. Function... 3 3. Technical data... 3 4. Contents of delivery... 4 5. General information... 5 6. Duty Mode...
More informationT M. User Manual. MarinaGuard. Ground Fault Monitoring Panel For Marina Shore Power
T M User Manual MarinaGuard Ground Fault Monitoring Panel For Marina Shore Power NAE1095810 / 03.2013 T M Bender Inc. USA: 700 Fox Chase Coatesville, PA 19320 Toll-Free: 800-356-4266 Phone: 610-383-9200
More informationTEMON 4-C. Doc. N MO-0368-ING TEMPERATURE MONITOR DEVICE TYPE TEMON 4-C OPERATION MANUAL. Microener- Copyright 2010 FW 2.1 Date Rev.
TEMPERATURE MONITOR DEVICE TYPE TEMON 4-C OPERATION MANUAL Microener- Copyright 2010 FW 2.1 Date 01.12.2008 Rev. 0 1. Generality 3 2. Introduction 3 3. Accessories and Options 3 4. Installation 3 5. Connection
More information20 Light Remote Annunciator
Light Remote Annunciator Owner s Manual Surface Mount Flush Mount 94-95- Standard Annunciator 94-, 94-95-, 95-4- 4- Annunciator w/remote Relay Panel 4-, 4-4-, 4-49-, 49-49-, 49- Time Multiplexed Annunciator
More informationEXPERT TRI-STAR. Temperature controller. User s Manual
Temperature controller r s Manual WARNINGS The warranty can be void if this product is used in a manner not specified by the manufacturer. Every effort has been made to ensure that this manual is complete,
More informationUSER MANUAL FOR OPERATING SYSTEM
P2262 ALARM PANEL USER MANUAL FOR OPERATING SYSTEM 21765-07 September 1999 Associated Controls (Aust) PTY. LTD. 29 Smith Street, Hillsdale, NSW, 2036. PH (02) 9311 3255, FAX (02) 9311 3779 Page 1 of 177
More informationConfiguration and Operation Manual for the Unipos
AxxonSoft Configuration and Operation Manual for the Unipos Integration Module Version 1.1 Moscow 2010 Contents CONTENTS... 2 1 LIST OF TERMS... 4 2 INTRODUCTION... 6 2.1 Document purpose... 6 2.2 Purpose
More informationNGC-40 Bridge. Modbus Overview. Raychem-AR-H58862-NGC40BridgeModbusOV-EN-1805 nvent.com 1
NGC-40 Bridge Overview Raychem-AR-H58862-NGC40BridgeOV-EN-1805 nvent.com 1 Table of Contents 1. NGC-40 Overview... 9 1.1 Example NGC-40 System... 10 2. Legal stuff... 11 3. Protocols... 12 3.1 Data es...
More informationHalton SAFE / 7.14 user guide and installation instructions
Halton SAFE / 7.14 user guide and installation instructions VERIFIED SOLUTIONS BY H A LTO N Enabling Wellbeing Table of contents 1 System description 3 2 User Accounts 4 3 Main menu 7 3.1 Main menu - Change
More informationType 8001 PRIME MOVER CONTROLS INC. ALARM ANNUNCIATOR TYPE8001 FEATURES SB 8001B
PRODUCT BULLETIN SB 8001B Type 8001 ALARM ANNUNCIATOR TYPE8001 FEATURES 16 or 32 alarm points per flush mount enclosure Displays are backlit with long life LEDs and engraved to suit Dimmer controls built
More informationUser manual. KNXgal. version
User manual version 1.3 gal Management alarm control panels Galaxy from bus powered from bus Communication indication on and with Galaxy control panel DIN rail mount (1 modul) Adjustable address on with
More informationAUTOMATION. Operator s Manual RST Series Web Enabled Input Module. Rev. A2, 1/12
AUTOMATION P R O D U C T S GROUP, INC. Operator s Manual RST-5000 Series Web Enabled Input Module Rev. A2, 1/12 Tel: 1/888/525-7300 Fax: 1/435/753-7490 www.apgsensors.com E-mail: sales@apgsensors.com RST-5000
More informationMODEL WIND TRACKER
MODEL 06201 WIND TRACKER NOVEMBER 2001 MANUAL PN: 06201-90 R. M. YOUNG COMPANY 2801 AERO PARK DRIVE, TRAVERSE CITY, MICHIGAN 49686, USA TEL: (231) 946-3980 FAX: (231) 946-4772 MODEL 06201 WIND TRACKER
More informationLineGuard 2300 Program User Manual (FloBoss 107)
Form A6251 Part Number D301346X012 November 2012 LineGuard 2300 Program User Manual (FloBoss 107) Remote Automation Solutions Revision Tracking Sheet November 2012 This manual may be revised periodically
More informationREMOTE CONTROL FOR CHILLER MYCHILLER
REMOTE CONTROL FOR CHILLER MYCHILLER GENERAL FEATURES... 3 MAIN FUNCTIONS AND EQUIPMENT:... 3 LCD DISPLAY... 4 KEYBOARD... 5 BOARD CONFIGURATION... 7 LIST OF MAIN PARAMETERS... 7 CONFIGURATION OF MAIN
More informationAdded password for IP setup page : Password must be in IP format!
NETWORK POWER MONITOR Release : 21 August 2014 Hardware Version : Version 7 Firmware version 1.00 PC Application Software : Version (latest)...2 Added password for IP setup page : Password must be in IP
More information: PRT / PRT PRT / PRT-N1
Model: PRT / PRT-N Model: PRT / PRT-N 1 Model: PRT / PRT-N Table of Contents Product Image Table of Contents What is a Programmable Room Thermostat? Installation Procedure LCD Display Setting the Clock
More informationFCD-wire Contents. List of Figures
FCD-wire Contents FCD-X21 Configuration 1 Introduction... 1 2 Opening the FCD Application... 1 3 FCD Window... 2 4 FCD LEDs... 3 5 Configuration Operations... 4 FCD Info...4 FCD System Info...5 FCD Interface
More informationSEC 3500 OI- StatCast RS232 Gas Status Text Broadcast Configuration Manual
SEC 3500 OI- StatCast RS232 Gas Status Text Broadcast August, 2006 Sensor Electronics Corporation 5500 Lincoln Drive USA (952) 938-9486 Table Of Contents: Intended Audience... 3 Purpose...3 Overview...
More informationModel: Touch-RS. 1 Touch-RS
Model: Touch-RS Model: Touch-RS 1 Touch-RS Table of Contents Product Image 1 Temperature Hold 15 Table of Contents 2 Holiday Programming 16 What is a Programmable Room Thermostat? Installation Procedure
More informationMeridian wiredhart. HART Field Device Specification Goldmine Rd. Monroe, NC USA
HART Field Device Specification Meridian wiredhart 4320 Goldmine Rd. Monroe, NC 28110 USA HART is a registered trademark of the HART Communication Foundation TABLE OF CONTENTS 1. Introduction...5 1.1 Scope...5
More informationZX1e ZX2e ZX5e. Document No Issue 01 user manual
ZX1e ZX2e ZX5e Document No. 996-130 Issue 01 user manual MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels Table of Contents 1 INTRODUCTION... 4 1.1 NOTICE... 4 1.2 WARNINGS AND CAUTIONS... 4 1.3 NATIONAL
More informationFlameGard 5 MSIR HART
FlameGard 5 MSIR HART Multi-Spectral Infrared Flame Detector HART Communication with the FlameGard 5 Multi-spectral Infrared Detector The information and technical data disclosed in this document may be
More informationModel A1700 Series Annunciator
Seekirk Model A1700 Series Annunciator Applications: For usage in all types of process industries, electric generation, transmission and distribution, gas and water utilities. Features: The Seekirk model
More informationModel: Touch-RF. 1 Wireless Series
Model: Touch-RF Model: Touch-RF 1 Wireless Series Table Of Contents Product Image 1 Locking the Keypad 18 Table of Contents 2 Temperature Control 19 What is a Programmable Room Thermostat? 3-4 Hot Water
More informationModel: PRT-TS / PRT-NTS
Model: PRT-TS / PRT-NTS Model: PRT-TS / PRT-NTS 1 Model: PRT-TS / PRT-NTS Table Of Contents Product Image 1 Temperature Control 14 Table of Contents 2 Temperature Hold 15 What is a Programmable Room Thermostat?
More information80 CHANNELS WIRELESS RECEIVER WITH LCD DISPLAY M1.1.1-Hx.x-F1.1-ENG [AN] [SPV] MADE IN ITALY INSTALLATION AND USE MANUAL
RX808-LCD 80 CHANNELS WIRELESS RECEIVER WITH LCD DISPLAY 14.12-M1.1.1-Hx.x-F1.1-ENG [AN] [SPV] MADE IN ITALY INSTALLATION AND USE MANUAL WARNINGS Installation: This device must be installed only by qualified
More informationRCS Residential Control Systems Inc.
RCS Residential Control Systems Inc. Model TZ16 Z-Wave Communicating Thermostat with Rev P HVAC Control Unit INSTALLATION AND OPERATION MANUAL DCN: 141-00882 Rev 02 5/18/06 This manual applies to the following
More information21-light Remote Annunciator. Owner s Manual
21-light Remote Annunciator Owner s Manual Annunciator Description... Inside Font Cover Detailed Specifications... 1 Environmental Specifications... 1 Power Supply Requirements... 1 Communication With
More informationSUPERINTEND VRE-08/16/32/64
SUPERINTEND VRE-08/16/32/64 Residual Current Monitoring System (RCM) for Grounded Electrical Systems 8/16/32/64 supervision points Operator Manual v2.00 Superintend VRE-08/16/32/64 operator manual v2.00
More informationEUROSCAN RX2-6 / TX2-6
Cabin and trailer recorder TABLE OF CONTENTS INTRODUCTION... 4 Data security... 4 Menu 1 Print menu... 6 1.1 Select compartment to print... 6 1.2 Time zone offset for printing... 6 1.3 Print event report...
More informationTECOM SYSTEMS NETWORK MASTER
TECOM SYSTEMS NETWORK MASTER The Tecom Network Master is a cost effective, Dialler Receiver and Direct Line Network Master combined in a single modular unit. HARDWARE The unit consists of a 3RU, 19 inch
More informationPipo Communications. Model ST-888. DTMF ANI/ENI Display Decoder
Pipo Communications Model ST-888 DTMF ANI/ENI Display Decoder 1516 Cassil Place Hollywood, California 90028-7106 Phone: 323-466-5444 Fax: 323-466-1520 www.pipo.cc Manual # 68-9888 May 1, 2002 Rev. 5/02
More informationControl Panel Type ABS CP 116/216 COMLI/Modbus - Version 1.25
Control Panel Type ABS CP 116/216 COMLI/Modbus - Version 1.25 81307049E EN Reference Manual 1 Comli/Modbus IO number layout 1.1 Digital outputs DO1 Alarm Relay 1 DO2 Alarm Relay 2 DO3 Alarm Relay 3 DO4
More informationCompod. Instruction Manual IM-COMPOD Revision: F, December 2015
Compod Programmable Control Module For 100 Series Digital Mass Flow Meters & Controllers Instruction Manual IM-COMPOD Revision: F, December 2015 CORPORATE HEADQUARTERS 5 Harris Court, Building L, Monterey,
More informationThermometers and temperature controllers
D144H002 Ed.07 GB Thermometers and temperature controllers User Manual Contents AKO Electromecánica thanks and congratulates you for purchasing our product, in whose development and manufacture the most
More informationModel : PRT-EN Model: PRT-EN1
Model: PRT-EN Model: PRT-EN 1 Model: PRT-EN Table of Contents Product Image Table of Contents What is a Programmable Room Thermostat? Installation Procedure LCD Display Setting the Clock Temperature Display
More informationTechnical Manual. Level Alarm Unit CARLA & WIDS
CARLA & WIDS Technical Manual SAS au Capital de 2 158 244-444 871 933 R.C.S. Bourges - APE : 2651B Headquarter : 9, rue Isaac Newton - 18000 Bourges - France Technical Manual CARLA for Tankers Cargo Tanks
More informationM3092 Programmer. User s Manual. M3096B-33 E Copyright 2017 SELCO
User s Manual Copyright 2017 SELCO SELCO Betonvej 11 - DK-4000 Roskilde Denmark Phone: 45 7026 1122 - Fax: 45 7026 2522 e-mail: selco@selco.com www.selco.com Table of contents 1 INTRODUCTION...4 2 SOFTWARE
More informationQ-SMART MODBUS KIT. Modbus Protocol & Parameters. Cod EN rev.a ed.08/2018. Q-SMART Software Version AE17
Q-SMART MODBUS KIT Modbus Protocol & Parameters Cod.001085120EN rev.a ed.08/2018 Q-SMART Software Version AE17 Index 1 Modbus Protocol on Q-SMART... 4 1.1 Broadcasting... 4 1.2 Data Protection... 4 1.3
More informationProduct Manual SZ1145
Product Manual SZ114 General Purpose Monitor Communicating Controls Description The SZ114 is a microprocessor-based monitoring and alarm interface designed to monitor up to four 1000 Ω platinum temperature
More informationModel SRCM Operation
Model SRCM Operation 1 Contents OPERATION... 4 Condition Banner... 6 Condition Banner Touch Screen... 7 Operation... 7 Alarms Cause Condition Banner to Turn Red... 7 Condition Banner Functions... 7 Operating
More informationCarbon Monoxide Transmitter
Introduction The CO Transmitter uses an electrochemical sensor to monitor the carbon monoxide level and outputs a field-selectable 4-20 ma or voltage signal. The voltage signal may also be set to 0-5 or
More informationUnderfloor Heating Programmable Thermostat
Underfloor Heating Programmable Thermostat t: 093 4906 m: 0794 69635 w: www.gs-ufh.co.uk e: gs@warmfloors.co.uk POWER CLOCK H A DOWN UP TO CHANGE THE TIMINGS AT ANY STAGE DURING THE PROCESS YOU CAN PRESS
More informationDryer Controller M720
User Manual Dryer Controller M720 Hardware version 2.00 Software version 2.00 Manual M720 Dryer controller Page 1 of 60 Document history Preliminary version: - Created in April, 2009 Hardware Version 2.00,
More informationThe Kryos LN2 Liquid Level Control & Cryogenic Temperature Control
The Kryos LN2 Liquid Level Control & Cryogenic Temperature Control Created for Taylor-Wharton Gas Equipment By Pacer Digital Systems, Inc. INTRODUCTION... 4 TEXT FORMAT NOTATION... 4 SYSTEM COMPONENTS...
More informationMounting and Operating Instructions EB 5610 EN. TROVIS 5600 Automation System TROVIS 5610 Heating and District Heating Controller
TROVIS 5600 Automation System TROVIS 5610 Heating and District Heating Controller Mounting and Operating Instructions Electronics from SAMSON EB 5610 EN Firmware version 1.40 Edition December 2014 Controller
More informationECO N DATE DESCRIPTION OF CHANGE CHG
Model Number: M21E-24-DIN Description: The product is a loop powered device which controls an unsupervised dual pole output channel suitable to manage 24VAC loads. The M21E-24-DIN is micro-controller operated,
More informationModel: Slimline-RF. 1 Slimline Series
Model: Slimline-RF Model: Slimline-RF 1 Slimline Series Table of Contents Product Image 1 Holiday Programming 22 Table of Contents What is a Programmable Room Thermostat? 2 3-4 Setting the Hot Water Switching
More informationACCURATE ELECTRONICS INC
ACCURATE ELECTRONICS INC Page 1 of 7 Model 108078 2 Sept 09 WWW.ACCURATE.ORG PO BOX 1654 97075-1654 8687 SW Hall Blvd 97008 BEAVERTON OR USA 503.641.0118 FAX 503.646.3903 Practice Section 108078 Rev A
More informationDTSX200 Communications(Modbus) Guide
User s Manual DTSX200 Communications(Modbus) Guide 4th Edition Blank Page < Introduction > i Introduction About this Manual Thank you for purchasing the DTSX200 Distributed Temperature Sensor. This document
More informationFL500 Modbus Communication Operating Manual. Order No.: /00. MSAsafety.com
FL500 Modbus Communication Operating Manual Order No.: 10193214/00 MSAsafety.com 1000 Cranberry Woods Drive Cranberry Township, PA 16066 A Phone 1-800-MSA-2222 Fax 1-800-967-0398 For your local MSA contacts
More informationSimpleComTools, LLC 1
COM1000-SNMP s Simple Network Management Protocol (SNMP) is a popular network management tool. Traditionally, SNMP was designed and used to gather statistics for network management and capacity planning.
More informationFlameGard 5 UV/IR HART
FlameGard 5 UV/IR HART HART Communication Manual The information and technical data disclosed in this document may be used and disseminated only for the purposes and to the extent specifically authorized
More informationGas Detection System TOX ALARM DG2000-Garage
Gas Detection System TOX ALARM DG2000-Garage Gas Detection System 32 independent programmable channels 2 programmable alarm levels for each gas = up to 6 for each channel LCD alphanumeric display of gas
More informationIntelligent Security & Fire Ltd
Product Data Sheet Mx-4000 Series User Manual MX-4100, MX-4200, MX-4400, Mx-4400/LE & Mx-4800 Fire Alarm Control Panels The operation and functions described in the manual are available from Software Versions
More informationDiagnostics and Monitoring System WEB Tool 2. User Manual
Diagnostics and Monitoring System 2 (Translation of the original documentation) User Manual S/N: Valid from: 01.05.2012 Rev.: 2.0 2 Rev. 1.... 1 1.1 General information... 1 1.1.1 Equipment... 1 1.1.2
More informationPRT-TS WiFi PRT-TS WiFi
Model: PRT-TS WiFi Model: PRT-TS WiFi 1 Model: PRT-TS WiFi Table Of Contents Product Image 1 Frost Protection 16 Table of Contents 2 Heating ON/OFF 16 What is a Programmable Room Thermostat? Installation
More informationUser Manual Ichill 200 L/D (Firmware version 1.7)
User Manual Ichill 2 L/D (Firmware version 1.7) Pag. 1 of 142 INDEX 1. GENERAL FEATURES...8 1.1 Main Function... 8 2. ICHILL 2L/D TABLE OF THE FEATURES...1 3. USER INTERFACE...11 4. REMOTE KEYBOARD...15
More informationInstallation Manual. ATS Remote Annunciator Catalog 5350 DANGER WARNING D
ASCO 5350 The ASCO 5350 ATS Remote Annunciator is listed under the Underwriter s Laboratories Standard UL-1008 for Automatic Transfer Switch accessories. This stand-alone device provides individual status
More informationRS 0021 DIGITAL GAS DETECTION CONTROL UNIT FOR SENSORS WITH S-BUS PROTOCOL. USER MANUAL Read carefully before use
RS 0021 DIGITAL GAS DETECTION CONTROL UNIT FOR SENSORS WITH S-BUS PROTOCOL USER MANUAL Read carefully before use GENERAL INFORMATION This device is a gas control unit with RS485 serial communication, based
More informationTable of Contents. SLIMLINE Series MODEL: SLIMLINE
Table of Contents Product Image 1 Table of Contents 2 What is a Programmable Room Thermostat? 3-4 Installation Procedure 5-6 LCD Display 7-8 Setting the Clock 9 Temperature Display 10 Setting the Comfort
More informationM2000 Engine Controller
M2000 Engine Controller Integrated control and protection of diesel and gas engines for all purposes Especially suited for auxiliary generator sets 1 IN OPERATION 1 2 STARTFAIL 2 3 OVERSPEED RPM FAIL 3
More informationProduct Manual SZ1144
Product Manual SZ1144 Refrigeration Temperature Monitor Communicating Controls Description The SZ1144 is a microprocessor-based monitoring and alarm interface designed to monitor up to four 1000 Ω platinum
More informationM2500 Engine Controller Installation Manual
M2500 Engine Controller Installation Manual Revision: 23-04-2012 Page 1 Contents 1 Preface... 4 2 Installation... 5 3 Terminal Connections... 6 4 Inputs... 7 4.1 Power Supply... 7 4.2 Mode/ Control Inputs...
More informationDX2002 OPERATING AND PROGRAMMING INSTRUCTIONS
DX2002 OPERATING AND PROGRAMMING INSTRUCTIONS The four pushbuttons located at the bottom right of the circuit board are used to do all programming. Each button has more than one function. Alternate Settings
More informationWeatherLink for Alarm Output Addendum
WeatherLink for Alarm Output Addendum Introduction This Streaming Data Logger is designed to provide an electrical interface between a Vantage Pro or Vantage Pro2 weather station console or Weather Envoy
More informationModSync Sequencing System Installation & Operation Manual. For use with Fulton Steam Boilers.
ModSync Sequencing System Installation & Operation Manual For use with Fulton Steam Boilers. Revision 3.0 8/21/2008 - 2 - Table of Contents Introduction Page 4 Features Page 4 Sequence of Operation Page
More informationD8024, D9024, D10024 Analog Fire Alarm Control Panels Programming Guide
System Reset Trou ble Silence Ala rm Silence Manual Ala rm ENTER NO YES Letters Numb ers Keyword Radionics System Reset Trouble Silence Alarm Silence Manual Alarm ENTER NO YES Le ters Numbers Keyw ord
More informationEasyTronic III MANUAL SERVICE
rev.6 EasyTronic III MANUAL SERVICE General characteristics: Power supply 24 Vac ±15% Max consumption at 24Vac 300mA Relay outputs 6 Maximum relay current 8 A res. Serial standard RS232 2 Serial standard
More informationRCS Residential Control Systems Inc.
RCS Residential Control Systems Inc. Model TR16 Communicating Thermostat With RS485 Communications INSTALLATION AND OPERATION MANUAL Rev P HVAC Control Unit DCN: 141-00930-09 Rev 09 7/13/06 This revision
More informationInstallation Manual Tracker 221
Installation Manual Tracker 221 KSR KUEBLER AG Im Kohlstatterfeld 17 D-69439 Zwingenberg / Germany www.ksr-kuebler.com Contents About this Installation Manual...4 Description Tracker 220-series...4 Installing
More informationModel A2100 Series Annunciator
Seekirk Model A2100 Series Annunciator Applications: For usage within transformers, switchgear, breakers and/or within any processing equipment or control room applications either attended or unattended
More information1600 Gas Controller. User s Manual. Industrial Scientific Corporation. Version 3.2 September 1, 2006
1600 Gas Controller User s Manual Version 3.2 September 1, 2006 Industrial Scientific Corporation 1 INTRODUCTION... 1 1.1 GENERAL OPERATION... 1 1.1.1 Power Up... 1 1.1.2 Viewing Sensors... 2 1.1.3 Acknowledging
More informationFI6000 INSTRUCTION MANUAL. Thank you for choosing another quality product from Amperes Electronics. Fire Alarm Interface
INSTRUCTION MANUAL FI6000 Fire Alarm Interface Thank you for choosing another quality product from Amperes Electronics. FI6000 is a phase evacuation controller which can be integrated with various Amperes
More informationM15-GSL12P30 M15-GSL12P30S Heat Spy Infrared Thermometer User Manual
M15-GSL12P30 M15-GSL12P30S Heat Spy Infrared Thermometer User Manual WD1097 Rev B 01/29/13 Wahl Instruments, Inc. 234 Old Weaverville Road Asheville, NC 28804 Toll Free 800-421-2853 Phone 828-658-3131
More informationModel: Edge-HC. 1 edge-hc
Model: Model: Edge-HC 1 edge-hc Table Of Contents Product Image Table of Contents Installation Procedure System Type LCD Display Power On/OFF Setting the Time & Date Mode Select Fan Speed Temperature Display
More informationYokogawa DX Ethernet Driver Help Kepware Technologies
Yokogawa DX Ethernet Driver Help 2012 Kepware Technologies 2 Table of Contents Table of Contents 2 4 Overview 4 Device Setup 5 Communications Parameters 7 Optimizing Your Ethernet Communications 9 Data
More informationMETEOROLOGICAL INSTRUMENTS
METEOROLOGICAL INSTRUMENTS INSTRUCTIONS MARINE WIND TRACKER MODEL 06206 R.M. YOUNG COMPANY 2801 AERO PARK DRIVE, TRAVERSE CITY, MICHIGAN 49686, USA TEL: (231) 946-3980 FAX: (231) 946-4772 WEB: www.youngusa.com
More informationModbus TCP/IP Option Instruction Manual
W A L C H E M An Iwaki America Company WebMaster Modbus TCP/IP Option Web Master WIND Modbus TCP/IP Option Instruction Manual s825v008 and higher Five Boynton Road Hopping Brook Park Holliston, MA 01746
More informationSCAN200E USER S MANUAL
SCAN200E USER S MANUAL Code No. 2071 1052 rev. 1.4 Code No. 2071 1052 Rev. 1.4 Page 2/16 SCAN200E User s Manual Foreword This manual is for SCAN200E Controller running software version 2.03 or later. We
More informationM800, M800iD Plus, M1000 and M3000. User's Guide
M800, M800iD Plus, M1000 and M3000 User's Guide Cooper Security Limited 2005 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security
More informationVTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL
VTI MODEL itc5000 HEAT TRACING CONTROL SYSTEM OPERATIONS MANUAL 1 Operations Manual for the VTI Model itc5000 Heat Tracing Control System Description The VTI Model itc5000 Heat Tracing Control System consists
More informationHOBO U14 Data Logger User Manual
HOBO U14 Data Logger User Manual The U family of data loggers offers reliability and convenient monitoring for applications that require higher accuracy, better resolution, more memory, or USB connectivity
More informationIntelligent Security & Fire Ltd. PX Control Panel. User Manual. Issue C
PX Control Panel User Manual Issue C Contents CONTENTS...2 INTRODUCTION...5 EVENT LOG...5 AREAS & SET GROUPS...5 CIRCUITS...5 USER, SET GROUP AND CIRCUIT IDENTIFICATION...6 USER CODES...6 OPERATOR CONTROLS
More informationOperating & Maintenance Manual. Alert-4 Ethernet LCD Master Alarm
Operating & Maintenance Manual Alert-4 Ethernet LCD Master Alarm w w w. a m i c o. c o m Contents User Responsibility 4 Introduction 4 Features 5 Description of the Alarm 5 Shipment Details 5 The Alarm
More information