INSTALLATION GUIDE XR150/XR550 SERIES CANADIAN CONTROL PANEL

Transcription

1 INSTALLATION GUIDE XR150/XR550 SERIES CANADIAN CONTROL PANEL

2 MODEL XR150CAN/XR550CAN Serie CANADIAN INSTALLATION GUIDE INDUSTRY CANADA NOTICE Thi Cla A digital apparatu complie with Canadian ICES , Inc. Information furnihed by DMP i believed to be accurate and reliable. Thi information i ubject to change without notice.

3 TABLE OF CONTENTS Product Specification 1.1 Power Supply Communication Panel Zone Keypad Bu LX-Bu Output Encloure Specification...2 Panel Feature 2.1 Decription Zone Epanion Output Epanion Central Station Communication Encrypted Communication (XR550 with Encryption only) Compliance Intruction...3 Sytem Component 3.1 Wiring Diagram Lightning Protection Acceory Device Acceory Device (continued)...6 Intallation 4.1 Mounting the Encloure Mounting Keypad and Zone Epanion Module Connecting LX-Bu and Keypad Bu Device Wirele Keypad Aociation...9 Primary Power Supply 5.1 AC Terminal 1 and Tranformer Type J12 3-Pin Header for Tranformer Type...9 Secondary Power Supply 6.1 Battery Terminal 3 and Earth Ground (GND) Battery Only Retart Battery Replacement Period Dicharge/Recharge Battery Superviion Battery Cutoff XR150/XR550 Serie Canadian Power Requirement Standby Battery Selection...13 Bell Output 7.1 Terminal 5 and Keypad Bu 8.1 Decription Terminal 7 - RED Terminal 8 - YELLOW Terminal 9 - GREEN Terminal 10 - BLACK J8 Programming Connection Keypad Bu LED OVC LED()...14 i

4 TABLE OF CONTENTS Smoke and Glabreak Detector Output 9.1 Terminal 11 and Current Rating...15 Protection Zone 10.1 Terminal Dual EOL Zone Repone Time Keywitch Arming Zone...15 Powered Zone for 2-Wire Smoke Detector 11.1 Terminal and Dry Contact Relay Output 12.1 Decription Contact Rating Model 431 Output Harne Wiring...16 Annunciator Output 13.1 Decription Model 300 Harne Wiring Model 860 Relay Module...17 Wirele Bu Epanion 14.1 Decription Wirele Bu LED...17 LX-Bu Epanion 15.1 LX-Bu Header LX-Bu LED OVC LED Decription Ethernet LED Network Tranient Suppreion...18 J3 Telephone RJ Connector 17.1 Decription J10 893A or 277 Trouble Sounder Connector Notification Phone Line Monitor...18 Reet and Tamper Header 18.1 J16 Reet Header J4 Tamper Header...19 Cellular Module 19.1 J24 Header Module Intallation Connecting the Antenna LX-Bu Module Connection Model 860 Relay Module Connection Dual Zone Protection...21 Certification ii

5 Product Specification INTRODUCTION 1.1 Power Supply Tranformer Input: Model 327CAN, plug-in Primary input: 120 Vac, 60 Hz, Secondary output: 16.5 Vac 50 VA Model FTA7516 ATC Frot from Stande Electronic Primary input: 120 Vac, 60 Hz, Secondary output: 16 Vac 75 VA Standby Battery: 12 VDC, 1.0 Amp Ma. charging current Model 365, 366, 368, or 369 Replace every 3 to 5 year Auiliary: 12 VDC output at 1.0 Amp Ma uing Model 327CAN Bell Output: 12 VDC at 1.0 Amp Ma uing Model 327CAN Auiliary: 12 VDC output at 1.5 Amp Ma uing Model FTA7516 Bell Output: 12 VDC at 1.5 Amp Ma uing Model FTA7516 All circuit are inherent Power Limited ecept the red battery wire and AC terminal. 1.2 Communication Built-in network communication to DMP Model SCS-1R Receiver (Panel with Network/Encryption only) Built-in 128-bit or 256-bit encrypted communication to DMP Model SCS-1R Receiver (XR550E only) Built-in Contact ID communication to DMP Model SCS-1R Receiver Optional 893A Dual Phone Line Module with phone line uperviion Can operate a a local panel Note: 256-bit encrypted meage to SCS-1R receiver only communicate when uing SCS-104 Receiver Line Card with Verion 102 or higher oftware. 1.3 Panel Zone Eight 1k Ohm EOL burglary zone (zone 1 to 8) Two 3.3k Ohm EOL powered zone with reet (zone 9 and 10) 1.4 Keypad Bu You can connect up to a total of 16 of the following upervied keypad and epanion module to the keypad bu: Alphanumeric keypad Single-zone detector Acce control module Wirele Keypad (maimum of 7) Four- and/or ingle-zone epanion module 1.5 LX-Bu You can connect the following device to the LX-Bu connection provided on the panel. See Acceory Device ection 3.3. Four, eight, iteen- and/or ingle-zone epanion module Single-zone detector Relay output epanion module Graphic annunciator module 1.6 Output The XR150/XR550 Serie provide two Single Pole, Double Throw (SPDT) relay output which require the intallation of two Model 305 relay, each rated 1 Amp at 30 VDC reitive (power limited ource only). A Model 431 Output Harne i required to ue thee output. The panel alo provide four open collector output rated for 50mA each. The open collector output provide ground connection for a poitive voltage ource. A Model 300 Output Harne i required to ue thee output. 1

6 INTRODUCTION 1.7 Encloure Specification The panel are hipped in an encloure with a tranformer, End-of-Line reitor, battery lead, uer guide, and programming heet. Encloure Model Size Color() Contruction (Cold Rolled Steel) W 13.5 H 3.5 D Gray (G) or Red (R) 18-Gauge 350A 17.5 W 13.5 H 3.75 D Gray (G) 18-Gauge with 16-Gauge door W 7.0 H 3.5 D Gray (G) 20-Gauge W 11.5 H 3.5 D Gray (G) 20-Gauge 352X 14.5 W 32.0 H 4.0 D Gray (G) 16-Gauge Panel Feature 2.1 Decription The DMP XR150/XR550 Serie Canadian panel i a veratile 12VDC, combined acce control, burglary, and fire communicator panel with battery backup. The panel provide eight on-board burglary zone and two on-board 12VDC Cla B powered zone. The powered zone have a reet capability to provide for 2-wire moke detector, relay, or other latching device. You can ue up to iteen upervied 32-character LCD keypad; network communication and epanion interface card; zone and output epanion module; and initiating and indicating circuit module. You can alo connect auiliary device to the panel output relay to epand the baic ytem control capability. Combined current requirement of additional module may require an auiliary power upply. Refer to the XR150/XR550 Serie Power Requirement ection in thi guide when calculating power requirement. The XR150/XR550 Serie can communicate to DMP SCS-1R Receiver uing digital dialer, cellular, network, or Contact ID communication. 2.2 Zone Epanion Each panel provide multiple option for zone epanion. 10 on-board zone Up to 64 programmable keypad zone Up to 500 LX-Bu zone Uing DMP LCD keypad remote zone capability and zone epanion module, additional zone are available on each panel: XR550 provide up to 574 additional zone XR150 provide up to 142 additional zone The panel keypad data bu upport up to 16 upervied device addree with each addre upporting up to four programmable epanion zone (64 total). Uing the on board LX-Bu (LX500-LX900) connection, and any combination of ingle, four, eight, or iteen-zone epanion module and ingle-zone LX-Bu detector, additional zone are available on each panel: XR550 provide up to 500 additional zone (LX500-LX900) XR150 provide up to 100 additional zone (LX500) Note: Do not ue hielded or twited pair wiring for LX-Bu or Keypad Bu circuit. 2.3 Output Epanion In addition to the two SPDT relay and four programmable open collector output on the XR150/XR550 Serie, you can alo connect up to 25 programmable Model 716 Output Epanion Module to each LX-Bu. Thee module can provide an additional 500, 300, or 100 programmable SPDT relay. The panel provide Output Schedule for programming the 716 to perform a variety of annunciation and control function. Alo aign the 716 output to any panel Output Option uch a Fire Alarm, Communication Fail, or Phone Trouble Output. Refer to the 716 Intallation Guide (LT-0183). The LX-Bu alo upport the Model 717 Graphic Annunciator Module. Each 717 module upplie 20 witched ground output that follow the tate of their aigned zone. Note: The 717 upport the firt eight Keypad Bu addree. To follow Keypad Bu addree nine through 16, intall multiple 716 module. Refer to the 717 Intallation Guide (LT-0235) and 716 Intallation Guide (LT 0183). 2.4 Central Station Communication You can program the panel for reporting to DMP SCS 1R Receiver uing digital dialer, cellular, network, or Contact ID communication. The panel connect at the premie to a tandard RJ31X or RJ38X telephone jack. Ue the DMP 893A Dual Phone Line Module when connecting the XR150/XR550 Serie panel to two eparate phone line. 2

7 INTRODUCTION 2.5 Encrypted Communication (XR550 with Encryption only) An XR550 panel with encryption communicate uing 128-bit or 256-bit AES encryption. If you currently have an XR550 panel intalled, you may contact DMP Cutomer Service with the panel erial number. The erial number() hould be ent in writing via or fa. A eparate feature key i ent for each panel to activate encrypted communication uing the Feature Upgrade proce. Encrypted communication cannot be enabled on a tandard XR550 panel. For more information on the Feature Upgrade proce ee the XR150/XR550 Serie Canadian Programming Guide (LT-1232CAN). Note: 256-bit encrypted meage to SCS-1R receiver only communicate when uing SCS-104 Receiver Line Card with Verion 102 or higher oftware. 2.6 Caution Note Throughout thi guide you will ee caution note containing information you need to know when intalling the panel. Thee caution are indicated with a yield ign. Whenever you ee a caution note, make ure you completely read and undertand it information. Failing to follow the caution note can caue damage to the equipment or improper operation of one or more component in the ytem. See the eample hown below. Alway ground the panel before applying power to any device: The panel mut be properly grounded before connecting any device or applying power to the panel. Proper grounding protect againt Electrotatic Dicharge (ESD) that can damage ytem component. 2.7 Compliance Intruction For application that mut conform to a local authoritie intallation tandard or a National Recognized Teting Laboratory certificated ytem, pleae ee the Compliance Liting Guide (LT-1330) for intruction. 3

8 INTRODUCTION Sytem Component 3.1 Wiring Diagram The XR550 Serie diagram below how ome of the acceory module you can connect for ue in variou application. A brief decription of each module follow in ection 3.3. AC Wiring mut be in conduit and eit out the left ide of the encloure. Wiring on terminal 5 through 22 mut eit right and maintain 1/4" eparation from the AC and battery poitive wiring. The plug-in tranformer hall plug into a 120 VAC 60 Hz outlet not controlled by a witch. ¼" Bell 12 VDC Minimum cutoff time 15 min. 1.5 Amp Ma uing FTA7516 AC J12 50VA 16 to 18 gauge wire Maimum AC Wire ditance with 16 gauge wire: 70 feet with 18 gauge wire: 40 feet RED BLACK Earth Ground 75VA Battery Start J3 Phone Line XR550 Serie Canadian Panel OVC J Output 3-6 J4 Tamper J8 Output 1 Output 2 LX500 K6 Lited Reitor 1.0k Ohm - DMP Model k Ohm - DMP Model K Ohm - DMP Model 308 J2 Out1 Out2 AC +B B BELLGND RED YEL GRN BLK SMK GND Z1 GND Z2 Z3 GND Z4 Z5 GND Z6 Z7 GND Z8 Z9+ Z9 Z10+ Z Cold Water Pipe Earth Ground 1k Ohm Bell 22 gauge minimum RED Bell cutoff time range i 5 to 99 minute, non-coded. 22 gauge minimum YELLOW 22 gauge minimum 22 gauge minimum GREEN BLACK K7 LX700 J13 XBUS LX800 LX900 Auiliary/Smoke Power Total current combined from terminal 7, 11, 25, 27, XBUS and LX500-LX Amp Ma 13.8 VDC to 10.2 VDC J16 Reet J14 J9 J15 J17 J19 Zone 1 Zone 2 1k 1k Ohm Ohm RED RED YELLOW GREEN BLACK Zone 3 Zone 4 Zone 5 Zone 6 Form C Relay (J2) Output Color Code Model 431 Harne Output 2 N/O Orange/White Output 2 Com White/Gray Output 2 N/C Violet/White Output 1 N/O Orange Output 1 Com Gray Output 1 N/C Violet Annunciator Output (J11) Output Color Code Output 3 Red Output 4 Yellow Output 5 Green Output 6 Black Zone 7 Zone 8 1k 1k Ohm Ohm 1k 1k Ohm Ohm 1k 1k Ohm Ohm Zone 9 J24 Zone k Ohm 3.3k Ohm Reitor DMP Reitor DMP Model 309 Model 309 = Supervied Circuit Front and Rear tamper protection included with Model 350A Attack Reitant Encloure. Front Tamper Rear Tamper Heat detector, pull tation, or any other contact device lited for Fire Protective Signaling can be connected to zone 9 and 10. Zone 9 and 10 and Model 715 compatibility identifier: A Maimum operating range: 13.8 VDC to 9.7 VDC. Cla B (Style A). Zone Epander Model VDC Model 715-8, VDC DISARM ARM 1k Ohm 1k Ohm 1k Ohm Ue Lited Power Superviion Relay rated at 12 VDC. Keywitch Arming can be connected to any zone. Smoke Detector Zone Epander Model VDC Model 714-8, VDC 1k Ohm 1k Ohm 1k Ohm Zone Epander Model VDC 1k Ohm Zone Epander (up to 8 zone) Model VDC WARNING: Incorrect connection may caue damage to the unit. 1k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm CAUTION: DO NOT USE LOOPED WIRE UNDER TERMINALS. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS. 1k Ohm Figure 1: XR550 Canadian Wiring Diagram 3.2 Lightning Protection Metal Oide Varitor and Tranient Voltage Suppreor help protect againt voltage urge on XR150/XR550 Serie input and output circuit. Additional urge protection i available by intalling the DMP 370, 370RJ Lightning Suppreor or Model 270 Network Tranient Suppreion Module. 4

9 INTRODUCTION 3.3 Acceory Device Cellular Communicator 263HCAN HSPA+ Canadian Cellular Communicator Acceory Module 270 Network Tranient Suppreion Module 277CAN Trouble Sounder 370/370RJ Lightning Suppreor 893A Dual Phone Line Module Allow you to connect the XR150/XR550 Serie to any compatible HSPA/SMS network. Provide tranient urge protection for the J1 Ethernet Connector. Provide local ounder for monitoring of panel operation and lo of Keypad Bu. Provide protection againt voltage urge on panel input and output circuit Allow you to upervie two tandard phone line connected to an XR150/XR550 Serie panel. The 893A module monitor the main and backup phone line for a utained voltage drop and alert uer when the phone line i bad. Epanion Module 710 Bu Splitter/Repeater Allow you to increae keypad or LX-Bu wiring ditance to 2500 feet. 711 Single Point Zone Epander Provide one Cla B zone for connecting burglary device. 714, 714-8, Zone Epander Provide Cla B zone for connecting burglary and non-powered fire device Zone Epander Provide Cla B zone for connecting burglary device. 715, 715-8, Zone Epander Provide 12VDC Cla B powered zone for connecting moke detector, glabreak detector, and other 2- or 4-wire device. 716 Output Epander Provide four Form C relay (SPDT) and four witched ground (open collector) for ue in a variety of remote annunciation and control application for ue on the LX-Bu only. 717 Graphic Annunciator Module Provide 20 zone following annunciator output (open collector) for ue in a variety of remote annunciation and control application for ue on the LX-Bu only. 734, 734N, 734N-WiFi Wiegand Provide ytem codele entry, and arming and diarming uing acce control reader. Interface Module DMP Two-Way Wirele Device 1100X/1100XH Wirele Receiver 1100R Repeater Support up to 500 device in reidential or commercial wirele operation. Provide additional range for wirele device Univeral Tranmitter Provide both internal and eternal contact that may be ued at the ame time to yield two individual reporting zone from one wirele tranmitter Univeral Tranmitter Provide an eternal contact Univeral Tranmitter Provide both internal and eternal contact that may be ued at the ame time to yield two individual reporting zone from one wirele tranmitter. Require EOL reitor for eternal contact. Provide Diarm/Diable functionality Univeral Tranmitter Provide both internal and eternal contact that may be ued at the ame time to yield two individual reporting zone from one wirele tranmitter Micro Window Tranmitter Provide a wirele window tranmitter Four-Zone Epander Provide four wirele zone Relay Output Provide one Form C relay LED Annunciator Provide a viual ytem tatu indicator Remote Indicator Light Provide a viual indication of a Panic ituation Door Sounder Provide a battery powered ounder PIR Motion Detector Provide motion detection with pet immunity. 1126R Motion Detector 1127C/1127W PIR Motion Detector Ceiling mount motion detector with panel programmable enitivity and Diarm/Diable functionality. Wall mount motion detector with panel programmable enitivity and Diarm/Diable functionality Glabreak Detector Detect the hattering of framed gla mounted in an outide wall and provide full-pattern coverage and fale-alarm immunity Receed Contact Provide a receed contact option for door or window application. 1135/1135DB Wirele Sounder Provide a wirele ounder Bill Trap Provide a ilent alarm option for retail and banking cah drawer Wall Button One button wall mounted wirele tranmitter. 5

10 INTRODUCTION 3.3 Acceory Device (continued) DMP Two-Way Wirele Device (continued) 1142BC Two-button Hold-up Belt Provide two-button hold-up operation with a belt clip. Clip Tranmitter 1142 Two-button Hold-up Provide permanently mounted under-the-counter two-button hold-up operation. Tranmitter (Four-Button) Key Fob tranmitter deigned to clip onto a key ring or lanyard (Two-Button) (One Button) 1164 Wirele Synchronized Smoke Detector Commercial or reidential, battery powered, wirele, low profile, photoelectric moke detector, with ynchronizing ounder Wirele Smoke Ring Intall on any traditional AC-powered, three wire, interconnected moke alarm ytem R Heat Detector Fied temperature and rate-of-rie heat detector Carbon Monoide Detector Carbon Monoide Detector. Interface Module 736P Radionic Popit Interface 738A Ademco Interface 738I ITI Interface Module 738Zplu Z-Wave Interface Module Allow a Radionic POPIT Sytem to interface with DMP XR150/XR550 Serie panel while maintaining Radionic wiring. Allow Ademco 5881 wirele receiver to interface with DMP XR150/XR550 Serie panel. Allow ITI SuperBu 2000 Serie wirele receiver to interface with DMP XR150/XR550 Serie panel. Provide connection for Z-Wave module. Indicating and Initiating Device 860 Relay Output Module Provide one relay and three relay ocket for epanion of up to four relay. 865 Supervied Style W or X Notification Circuit Module 866 Style W Notification Circuit Module 867 Style W LX-Bu Notification Circuit Module 869 Dual Cla A Style D Initiating Module Keypad LCD keypad Provide upervied alarm current when uing the XR150/XR550 Serie panel bell output and up to 5 Amp at 12 or 24VDC when uing a lited auiliary power upply. The 865 can upervie 2-wire or 4-wire tyle circuit for open and hort with individual LED annunciation. Provide upervied alarm current uing the XR150/XR550 Serie panel bell output and up to 5 Amp at 12 or 24VDC when uing a lited auiliary power upply. The 866 can upervie 2-wire Style W circuit for open and hort. Provide upervied alarm current uing the XR150/XR550 Serie panel bell output and up to 5 Amp at 12 or 24VDC when uing a lited auiliary power upply. The 867 connect to the XR150/XR550 Serie panel LX-Bu and provide one 2-wire Style W notification circuit for open and hort condition. Individual Bell Relay addree Bell Ring tyle. Provide two Cla A, Style D, 4-wire initiating zone for connecting waterflow witche and other non powered fire and burglary device. Allow you to control the panel from variou remote location. Connect up to iteen upervied Model 630F Remote Fire Command Center, 7060, 7063, 7070, 7073, 7160, 7163, 7170, 7173 Thinline keypad, 7060A, 7063A, 7070A, 7073A Aqualite keypad, and 7872 and 7873 Graphic Touchcreen keypad to the keypad bu uing terminal 7, 8, 9, and Serie Wirele Keypad Allow you to control the panel from variou remote location. Connect up to even 9060/9063 Wirele Keypad Serie Wirele Graphic Allow you to control the panel from variou remote location. Connect up to even 9862 Touchcreen keypad Wirele Keypad. Addreable Smoke Detector 521LX, 521LXT Single-zone, addreable conventional moke, moke/heat detector that connect to the LX-Bu. Include remote maintenance reporting, drift compenation, and multi-criteria detection. 2W-BLX, 2WT-BLX Single-zone, addreable conventional moke, moke/heat detector that connect to the LX-Bu. Include drift compenation. 6

11 J23 J6 INSTALLATION Intallation 4.1 Mounting the Encloure The metal encloure for the XR150/XR550 Serie mut be mounted in a ecure, dry place to protect the panel from damage due to tampering or the element. It i not neceary to remove the XR150/XR550 Serie PCB when intalling the encloure. Figure 2 how the mounting hole location for the Model 350/350A Encloure. Figure 3 how the Model 341 Encloure. Figure 4 how the Model 352X panel cabinet and 352S helf cabinet for multiple batterie. The 350A Attack Reitant encloure i factory hipped with one knockout on the top left of the encloure. A needed, additional knockout or antenna eit may be added at the time of intallation. See Figure 2 for the poition on the encloure that can be added. Each additional knockout mut be filled with conduit. Encloure Mounting Hole * XR550 Panel J6 3-Hole Pattern for Acceory Module K J23 * * Dual 1 3/4" and 1 3/8" Conduit Knockout * 350A Optional Knockout Front and Rear Tamper Switche for 350A Attack Reitant Encloure * Battery Shelf hold up to three 7 Ah Batterie * Figure 2: XR550 Serie in Model 350 or 350A Encloure Lid Mounting Hole (4 place) PEM for optional battery bracket. See 341 Intallation heet for additional information. Lid Mounting Hole (4 place) XR550 Panel K Encloure Mounting Hole (4 place) Dual 1/2" and 3/4" Conduit Knockout Figure 3: XR550 Serie in Model 341 Encloure 7

12 K J6 INSTALLATION 56 VA Tranformer Mounting Plate XR550 Panel XR550 Panel Mounting for one (1) Zone Epanion Module. Battery Shelf Figure 4: XR550 Serie in Model 352X Encloure and Separate 352S Encloure with Shelve 4.2 Mounting Keypad and Zone Epanion Module DMP LCD keypad have removable cover that allow you to eaily mount the keypad to a wall or other flat urface uing the crew hole on each corner of the bae. Before mounting the bae, connect the keypad wire harne lead to the keypad cable from the panel and to any device wiring run to that location. Then attach the harne to the pin connector on the PC board, mount the bae, and intall the keypad cover making ure all of the key etend through their repective hole. For mounting keypad on olid wall, or for application where conduit i required, ue the Model /2 deep or the Model 696 1/2 deep backboe. The DMP 711, 712-8, 714, 715, 716, and 717 module are each contained in molded platic houing with removable cover. The bae provide you with mounting hole for intalling the unit to a wall, witch plate, or other urface. 8

13 INSTALLATION 4.3 Connecting LX-Bu and Keypad Bu Device Connection for LX-Bu and Keypad are provided through the J8 (PROG), J14 (LX500), J9 (LX600), J15 (LX700), J17 (LX800), J19 (LX900), and J13 (XBUS) 4-pin header. Several factor determine the DMP LX-Bu and keypad bu performance characteritic: the wire length and gauge ued, the number of device connected, and the voltage at each device. When planning an LX-Bu and keypad bu intallation, keep in mind the following information: DMP recommend uing 18 or 22-gauge unhielded wire for all keypad and LX-Bu circuit. Do not ue twited pair or hielded wire for LX-Bu and keypad bu data circuit. On keypad bu circuit, to maintain auiliary power integrity when uing 22-gauge wire do not eceed 500 feet. When uing 18-gauge wire do not eceed 1,000 feet. To increae the wire length or to add device, intall an additional power upply that i lited for Fire Protective Signaling, power limited, and regulated (12VDC nominal) with battery backup. Note: Each panel allow a pecific number of upervied keypad. Add additional keypad in the unupervied mode. Refer to the Keypad Bu ection for the pecific number of upervied keypad allowed. Maimum ditance for any one bu circuit (length of wire) i 2,500 feet regardle of the wire gauge. Thi ditance can be in the form of one long wire run or multiple branche with all wiring totaling no more than 2,500 feet. A wire ditance from the panel increae, DC voltage on the wire decreae. Maimum number of LX-Bu device on the firt 2,500 foot circuit i 40 device. Maimum voltage drop between the panel (or auiliary power upply) and any device i 2VDC. If the voltage at any device i le than the required level, add an auiliary power upply at the end of the circuit. When voltage i too low, the device cannot operate properly. For additional information refer to the LX-Bu/Keypad Bu Wiring Application Note (LT-2031). 4.4 Wirele Keypad Aociation Enable Wirele Keypad Aociation operation on both the keypad and panel: 1. Acce the Intaller Option Menu (3577 (INST)). 2. Select RF Survey). The keypad logo LED turn on red until aociation i ucceful. Enable Wirele keypad Aociation operation in the XR150/XR550 panel: Reet panel 3 time within 12 econd. Allow the keypad bu Tranmit/Receive LED to turn back on between each reet. For 60 econd the panel liten for wirele keypad that are in the Intaller Option Menu (3577 CMD) and have not been programmed, or aociated into another panel. Thoe keypad are aigned to the firt open device poition automatically baed upon the order in which they are detected. The keypad logo turn Green to indicate it ha been aociated with the panel. Figure 5: Keypad Bu LED Primary Power Supply 5.1 AC Terminal 1 and 2 Connect the tranformer wire to terminal 1 and 2 on the panel. Ue no more than 70 ft. of 16 gauge or 40 ft. of 18 gauge wire between the tranformer and the XR150/XR550 Serie. Alway ground the panel before applying power to any device: The XR150/XR550 Serie mut be properly grounded before connecting any device or applying power to the panel. Proper grounding protect againt Electrotatic Dicharge (ESD) that can damage ytem component. See the Earth ground ection. 5.2 Tranformer Type Ue Model 327CAN (16.5 Vac 50 VA) plug-in or Model FTA7516 from ATC Frot. The tranformer mut be connected to an unwitched 120 Vac 60 Hz electrical outlet with at leat.87a of available current. Never hare the tranformer output with any other equipment. 5.3 J12 3-Pin Header for Tranformer Type Place the jumper on the left two pin for a Maimum 2 Amp (Bell+Au+Smoke+XBUS+LX500-LX900) when uing the Model 327CAN plug-in tranformer (default). Ue an ATC Frot FTA7516 tranformer and place the jumper on the right two pin for a Maimum, 3 Amp (Bell+Au+Smoke+XBUS+LX500-LX900). 9

14 INSTALLATION Secondary Power Supply 6.1 Battery Terminal 3 and 4 Connect the black battery lead to the negative battery terminal. The negative terminal connect to the encloure ground internally through the XR150/XR550 Serie circuit board. Connect the red battery lead to the battery poitive terminal. Oberve polarity when connecting the battery. You can add a econd battery in parallel uing the DMP Model 318 Dual Battery Harne. DMP require each battery be eparated by a PTC in the battery harne wiring to protect each battery from a reveral or hort within the circuit. See Figure 6. Ue ealed lead-acid batterie only: Ue the Model 365 (12VDC 9 Ah), Model 366 (12VDC 18 Ah), Model 368 (12VDC 5.0 Ah), or Model 369 (12VDC 7 Ah) ealed lead acid rechargeable battery. Batterie upplied by DMP have been teted to enure proper charging with DMP product. GEL CELL BATTERIES CANNOT BE USED WITH THE XR150/XR550 SERIES PANEL. 318 Battery Harne Battery Battery PTC 318 Battery Harne PTC Red Black Red Black Battery To AC Battery Start AC AC +B B Panel Red and Black Battery Cable 14 AWG to Earth Ground To Bell Figure 6: Wiring Multiple Batterie XR550 Panel Circuit BELL GND Earth Ground (GND) To provide proper tranient uppreion, XR150/XR550 Serie panel terminal 4 mut be connected to earth ground uing 14 gauge or larger wire. DMP recommend connecting to a cold water pipe, ground rod, or building ground only. Do not connect to an electrical ground or conduit, prinkler or ga pipe, or to a telephone company ground. 6.3 Battery Only Retart When powering up the XR150/XR550 Serie panel without AC power, briefly hort acro the battery tart pad to pull in the battery cutoff relay. The lead need a momentary hort only. Once the relay ha pulled in, the battery voltage hold it in that condition. If the XR150/XR550 Serie panel i powered up with an AC tranformer, the battery cutoff relay i pulled in automatically. For more information refer to Figure Battery Replacement Period DMP recommend replacing the battery every 3 to 5 year under normal ue. 6.5 Dicharge/Recharge The XR150/XR550 Serie battery charging circuit float charge at 13.8VDC at a maimum current of 1.0 Amp. Lited below are the variou battery voltage level condition: Battery Trouble: Below 11.9VDC Battery Cutoff: Below 10.2VDC Battery Retored: Above 12.6VDC 6.6 Battery Superviion The XR150/XR550 Serie tet the battery when AC power i preent. The tet i done every three minute and lat for five econd. During the tet, the panel place a load on the battery; if the battery voltage fall below 11.9VDC a low battery i detected. If AC power i not preent, a low battery i detected any time the battery voltage fall below 11.9VDC. If a low battery i detected with AC power preent, the tet repeat every two minute until the battery charge above 12.6VDC indicating the battery ha retored voltage. If a weak battery i replaced with a fully charged battery, the retored battery will not be detected until the net two minute tet i completed. 6.7 Battery Cutoff The panel diconnect the battery any time the battery voltage drop below 10.2VDC. Thi prevent battery deep dicharge damage. 10

15 INSTALLATION 6.8 XR150/XR550 Serie Canadian Power Requirement During AC power failure, the XR150/XR550 Serie panel and all connected auiliary device draw their power from the battery. All device mut be taken into conideration when calculating the battery tandby capacity. The following table lit the XR150/XR550 Serie panel power requirement. You mut add the additional current draw of keypad, zone epanion module, moke detector output, and any other auiliary device ued in the ytem for the total current required. The total i then multiplied by the number of tandby hour required to calculate the total ampere-hour required. Standby Battery Power Calculation Standby Current Alarm Current XR150/XR550 Serie Control Panel Relay Output 1-2 (ON) Switch Ground 3-6 (ON) Active Zone 1-8 Active Zone Wire Smoke Detector Panel Bell Output Qty 1 _ 174mA 174 ma 30mA 5mA 1.6mA 4mA 0.1mA Qty 1 _ 217mA 217 ma 30mA 5mA 2mA* 30mA 0.1mA 1500mA ma 893A Dual Phone Line Module 12mA 50mA 263HCAN HSPA+ Cellular Communicator 24mA 28mA 277CAN Trouble Sounder Module 5mA 5mA 1100X Wirele Receiver 46mA 46mA 1100XH Wirele High Power Receiver 160mA 160mA 860 Relay Output Module (one relay active) All four relay active 34mA 138mA 34mA 138mA 865 Style Y or Z Notification Module 26mA 85mA 866 Style W Notification Module 45mA 76mA 867 LX-Bu Style W Notification Module 30mA 86mA 869 Dual Style D Initiating Module 25mA 75mA 7060/7160 Thinline/7060A Aqualite Keypad 72mA 80mA 7063/7163 Thinline/7063A Aqualite Keypad 85mA 100mA 7070/7170 Thinline/7070A Aqualite Keypad Active Zone (EOL Intalled) 7073/7173 Thinline/7073A Aqualite Keypad Active Zone (EOL Intalled) 7872 Graphic Touchcreen Keypad Active Zone (EOL Intalled) 7873 Graphic Touchcreen Keypad Active Zone (EOL Intalled) 734 Wiegand Interface Module Active Zone (EOL Intalled) Annunciator (ON) 734N Wiegand Interface Module Active Zone (EOL Intalled) Annunciator (ON) Wiegand Reader 734N-WiFi Wiegand Interface Module Active Zone (EOL Intalled) Annunciator (ON) Wiegand Reader Copy Sub-Total to net page *Baed on 10% of active zone in alarm. 72mA 1.6mA 85mA 1.6mA 145mA 1.6mA 143mA 1.6mA 15mA 1.6mA 146mA 1.6mA 200mA 146mA 1.6mA 200mA Sub-Total Standby ma 87mA 2mA* 100mA 2mA* 215mA 2mA* 243mA 2mA* 15mA 2mA* 20mA 148mA 2mA* 20mA 200mA 148mA 2mA* 20mA 200mA Sub-Total Alarm ma 11

16 INSTALLATION Standby Battery Power Calculation Standby Current Alarm Current 736P POPIT Interface Module Radionic Pope, POPIT, OctoPOPIT 25mA ma 25mA ma 738A Ademco Wirele Interface Module 75mA 75mA 738Zplu Z-Wave Interface Module 35mA 35mA 710 Bu Splitter/Repeater Module 32mA 32mA 711 Zone Epanion Module Active Zone (EOL Intalled) 714 Zone Epanion Module Active Zone (EOL Intalled) Zone Epanion Module Active Zone (EOL Intalled) 714-8, Zone Epanion Module Active Zone (EOL Intalled) 715 Zone Epanion Module Active Zone (EOL Intalled) 2-Wire Smoke 715-8, Zone Epanion Module Active Zone (EOL Intalled) 2-Wire Smoke 716 Output Epanion Module Active Form C Relay 717 Graphic Annunciator Module Annunciator Output 11mA 1.6mA 7mA 1.6mA 17mA 1.6mA 20mA 1.6mA 7mA 4mA.1mA 20mA 4mA.1mA 13mA 10mA 11mA 2mA* 7mA 2mA* 17mA 2mA* 20mA 2mA* 7mA 30mA*.1mA 20mA 30mA*.1mA 13mA 12mA 10mA 1mA 521LX, 521LXT Smoke Detector 8.8mA 28mA* 2W-BLX, 2WT-BLX Smoke Detector 15mA 36mA* 572 Indicator LED 20mA 20mA Au. Powered Device on Terminal 7 and 11 Other than Keypad and LX-Bu Module ma ma Thi page only Sub-Total Standby ma Sub-Total Alarm ma Sub-Total from previou page Sub-Total Standby ma Sub-Total Alarm ma *Baed on 10% of active zone in alarm Total Standby ma Total Alarm ma Total Standby ma number of Standby Hour needed = Total Alarm ma Total Refer to ection 6.9 for tandby battery election. ma-hour + ma-hour ma-hour X.001 = Amp-hr Required 12

17 INSTALLATION 6.9 Standby Battery Selection To chooe the type and number of batterie needed for 24, 60, or 72 hour of tandby power baed on the Amp Hour Required calculation from ection 6.8 XR150/XR550 Serie Power Requirement, perform the following: 1. Select the deired tandby hour required from the table below: 24, 60, or 72 hour. 2. Select the deired battery ize: Model 368 (12VDC 5.0 Ah), Model 369 (12VDC 7 Ah), Model 365 (12VDC 9 Ah), Model 366 (12VDC 18 Ah). 3. Select a Ma. Ah Available number that i jut greater than the number calculated in Amp Hour Required. 4. Intall the number of batterie hown in the correponding No. of Batterie required column. Eample: If the Amp Hour Required calculation equal 22 Ah for 24 hour of tandby time and 4.5 Ah batterie are deired, intall i (6) Model 368 (12VDC, 5.0 Ah) batterie. Note: You can ue either a Model 327CAN Plug-in 50 VA or ATC Frot FTA VA Tranformer with any of the Number of Batterie choice lited below. 24 hour of tandby power 5.0 Ah Batterie 7 Ah Batterie 7.7 Ah Batterie 9 Ah Batterie 18 Ah Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Note: 48 hour i the typical battery recharge time for any of the Number of Batterie hown in thi ection. 60 hour of tandby power 7 Ah Batterie 7.7 Ah Batterie 9 Ah Batterie 18 Ah Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Note: 48 hour i the typical battery recharge time for any of the Number of Batterie hown in thi ection hour of tandby power 9 Ah Batterie 18 Ah Batterie Ma. Ah Available No. of Batterie Ma. Ah Available No. of Batterie Note: 72 hour i the typical battery recharge time required for any of the Number of 67 8 Batterie hown in thi ection. Note: If the Amp Hour Required calculation i greater than any Ma. Ah Available number hown on a table, then add power upply() to power ome ytem device allowing the Amp Hour Required calculation to be reduced. See the 710 Bu Splitter/Repeater Intallation Guide (LT-0310). 13

18 INSTALLATION Bell Output 7.1 Terminal 5 and 6 Terminal 5 upplie poitive 12VDC to power alarm bell or horn. Thi output can be teady, puled, or temporal depending upon the Bell Action pecified in Bell Option. Terminal 6 i the ground reference for the bell circuit. Thi upervied output detect 1k Ohm or le a normal. The indicating appliance can upply thi reitance. If uing a horn or iren, a 1k Ohm 1/2 W EOL reitor (provided) hould be added acro the bell circuit to provide uperviion. See the Notification Appliance ection for a lit of approved notification appliance and the Wiring Diagram for connection. Keypad Bu 8.1 Decription XR150/XR550 Serie panel terminal 7, 8, 9, and 10 are for the keypad bu. You can connect up to iteen upervied keypad and multiple unupervied keypad to the XR150/XR550 Serie. In addition to DMP LCD keypad, you can alo connect any combination of zone epanion module to the data bu up to 16 device. Note: Do not ue hielded wire for LX-Bu/Keypad Bu circuit. 8.2 Terminal 7 - RED Thi terminal upplie poitive 12VDC Regulated to power DMP LCD keypad and zone epanion module. Terminal 7 alo upplie power for any auiliary device. The ground reference for terminal 7 i terminal 10. The output current i hared with the moke power output on terminal 11 and Zone 9 and 10. Current draw for all connected device mut not eceed the panel maimum current rating. See Power Supply in the Compliance ection for maimum current in a fire lited application. 8.3 Terminal 8 - YELLOW Terminal 8 receive data from keypad and zone epanion module. It cannot be ued for any other purpoe. 8.4 Terminal 9 - GREEN Terminal 9 tranmit data to keypad and zone epanion module. It cannot be ued for any other purpoe. 8.5 Terminal 10 - BLACK Terminal 10 i the ground reference for DMP LCD keypad, zone epanion module, and all auiliary device being powered by terminal J8 Programming Connection A 4-pin header (J8) i provided to connect a keypad when uing a DMP Model 330 Programming Cable. Thi provide a quick and eay connection for panel programming. You may alo ue the Programming Header to connect Keypad Bu device. Thi i an alternative to connecting keypad bu device to terminal 7, 8, 9, and Keypad Bu LED The two LED, located above the J8 PROG connector, indicate data tranmiion and receipt. The left LED flahe green to indicate the panel i tranmitting keypad bu data. The right LED flahe yellow to indicate the panel i receiving keypad bu data. See Figure OVC LED() The Overcurrent LED (OVC) light red when the device connected to the Keypad Bu and LX-Bu(e) draw more current than the panel i rated for. The LED() turn a teady red when lit. When the OVC LED() light red, the appropriate LX-Bu(e) and Keypad bu are hut down. The OVC LED located to the left of the 893A connector indicate overcurrent for the Keypad Bu (Terminal 7-10 and PROG header), XBUS, and LX500-LX700. The OVC LED to the right of the J24 Cell Module connector indicate overcurrent for LX800-LX

19 Smoke and Glabreak Detector Output INSTALLATION 9.1 Terminal 11 and 12 Terminal 11 upplie poitive 12VDC Regulated to power 4-wire moke detector and other powered device. Thi output can be turned off by the uer for 5 econd uing the Senor Reet Uer Menu option to allow latched device to reet. Terminal 12 i the ground reference for terminal Current Rating The Output current from terminal 11 i hared with terminal 7, 25, 27, and LX500-LX900. Caution: The total current draw of all device powered from the panel mut be included with terminal 11 calculation and mut not eceed the maimum output rating. Protection Zone 10.1 Terminal Zone 1 to 8 (terminal 13 to 24) on the XR150/XR550 Serie panel are all grounded burglary zone. For programming purpoe, the zone number are 1 through 8. Lited below are terminal 13 to 24 connection function. Terminal Function Terminal Function 13 Zone 1 voltage ening 19 Zone 5 voltage ening 14 Ground for Zone 1 and 2 20 Ground for Zone 5 and 6 15 Zone 2 voltage ening 21 Zone 6 voltage ening 16 Zone 3 voltage ening 22 Zone 7 voltage ening 17 Ground for Zone 3 and 4 23 Ground for Zone 7 and 8 18 Zone 4 voltage ening 24 Zone 8 voltage ening The voltage ening terminal meaure the voltage acro a 1k Ohm End-of-Line reitor to ground. Ue DMP Model 311 1k Ohm reitor. Dry contact ening device can be ued in erie (normally-cloed) or in parallel (normally-open) with any of the burglary protection zone. Each protection zone detect three condition: Open, Normal, and Short. Lited below are voltage and reitance parameter for each condition: Condition Reitance on zone Voltage on poitive terminal Open over 1300 Ohm over 2.0VDC Normal 600 to 1300 Ohm 1.2 to 2.0VDC Short under 600 Ohm under 1.2VDC 10.2 Dual EOL The XR150/XR550 Serie Canadian panel upport the ue of dual 1K EOL reitor on panel Zone 1-8. Two EOL reitor are ued o a wire trouble can be indicated during the diarm period. When dual end-of-line operation i choen in panel programming, normal zone proceing occur with the following eception: When proceing an open zone and a trouble or alarm meage i NOT programmed to be ent for the open tate, the panel check to ee if the wire i cut. If the wire i cut, the panel automatically end an alarm if armed or trouble i diarmed. ZONE STATUS Figure 7: Protection Zone Wiring Zone Wire Open Zone Wire Short Contact Normal Contact Open N/C Diarmed Trouble Trouble Normal Normal 1K Ohm Armed Alarm Alarm Normal Alarm Indicating Device 10.3 Zone Repone Time A condition mut be preent on a zone for 500 milliecond before it i detected by the XR150/XR550 Serie panel. Enure detection device ued on the protec tion zone are rated for ue with thi delay. Zone 1-10 can alo be programmed for a fat repone delay of 160 milliecond Keywitch Arming Zone A keywitch on an Arming type zone allow elected area to arm and diarm without having to enter a uer code. 1K Ohm Normally Cloed 1K Ohm Normally Open 1K Ohm Combination Normally Open and Normally Cloed Zone Wire to Panel Zone 1-8 TAMP 1K Ohm N/O C 15

20 INSTALLATION Powered Zone for 2-Wire Smoke Detector 11.1 Terminal and Panel terminal 25 through 28 provide two reettable Cla B, Style A, 2-wire powered zone. For programming purpoe the zone number are 9 and 10. Note: The maimum wire length for either zone 9 or zone 10 i 3000 feet uing 18 AWG or 1000 feet uing 22 AWG. The maimum voltage i 13.8VDC and the maimum normal tandby current i 1.25mA DC. The maimum line impedance i 100 Ohm. The maimum hort circuit current i 56mA. Do not mi detector from different manufacturer on the ame zone. Caution: Performing a Senor Reet momentarily drop power to the device on Zone 9 and 10. The panel view thee zone (9 and 10) a Open while the power i abent. Note: Refer to the Compliance Liting Guide (LT-1330 )for lit of compatible DMP 2-wire moke detector. Dry Contact Relay Output 12.1 Decription The XR150/XR550 Serie panel provide two programmable auiliary SPDT relay when equipped with two DMP Model 305 relay in ocket K6 (Output 1) and K7 (Output 2) and a Model 431 Output Harne on the J2 6-pin Header. Each relay provide one SPDT et of contact that can be operated by any of the function lited below: 1) Activation by zone condition: Steady, Puling, Momentary, and Follow 2) Activation by 24-hour 7-day chedule: One on and one off time a day for each relay 3) Manual activation from the DMP LCD keypad menu 4) Communication failure 12) Ready 5) Armed area annunciation 13) Armed 6) Fire Alarm, Fire Trouble or Superviory 14) Diarmed 7) Ambuh Alarm 15) Burglary 8) Eit and Entry timer 16) Phone Trouble 9) Sytem Ready 17) Device Fail 10) Late to Cloe 18) Senor Reet 11) Panic Alarm 19) Cloing Wait Refer to the XR150/XR550 Canadian Serie Programming Guide (LT-1232CAN) for pecific information Contact Rating The Model 305 relay contact are rated for 1 Amp at 30VDC (allow.35 power factor). You can connect auiliary power to the Relay Output 1 common terminal by intalling the gray harne wire to terminal 7. Current draw for all connected device mut not eceed the panel maimum current rating Model 431 Output Harne Wiring The relay contact are acceible by intalling the DMP 431 Output Harne on the 6-pin header labeled J2. Output 2 ue the top three prong, and Output 1 ue the bottom three prong. The wire harne and contact location are hown below: Contact Color Output 1 normally cloed Violet Output 1 common Gray Output 1 normally open Orange Output 2 normally cloed Violet with white tripe Output 2 common White with gray tripe Output 2 normally open Orange with white tripe The relay contact mut be connected to device located within the ame room a the XR150/XR550 Serie panel. 16

21 Annunciator Output INSTALLATION 13.1 Decription The four programmable annunciator output can be programmed to indicate the activity of the panel zone or condition occurring on the ytem. Annunciator output do not provide a voltage but intead witch-to-ground a voltage from another ource. The output can repond to any of the condition lited in the Decription ection for Dry Contact Relay. Maimum voltage i 30VDC at 50mA Model 300 Harne Wiring Acce the open collector output by intalling DMP 300 Harne on the 4-pin header labeled J11. The output location are hown below. For lited application, device connected to the output mut be located within the ame room a the panel. Output Color Wire Output Color Wire 3 Red 1 5 Green 3 4 Yellow 2 6 Black Model 860 Relay Module Connect a Model 860 Relay Module to the J11 header on the XR150/XR550 Serie panel to provide relay for output 3-6. Ue thee relay for electrical iolation between the alarm panel and other ytem or for witching voltage to control variou function. Power i upplied to the relay coil from a ingle wire connected to the panel auiliary power terminal 7. The module include one relay and provide three additional ocket for epanion of up to four relay. Mount the 860 inide the panel encloure uing the 3-hole pattern and platic tandoff. Refer to the 860 Module Intall Sheet (LT-0484) a needed. Relay Contact Rating: 1 Amp at 30VDC (allow.35 power factor) Wirele Bu Epanion 14.1 Decription The J13 Wirele Bu (XBUS) header provide connection for the 1100X or 1100XH Wirele Receiver. The XBUS provide up to 500 wirele zone numbered Refer to the 1100X Wirele Receiver Intall Guide (LT-0708) or the 1100XH Wirele Receiver Intall Guide (LT-0970) for complete information. XR550 provide up to 500 zone XR150 provide up to 100 zone 14.2 Wirele Bu LED The two LED, located above the XBu header, indicate data tranmiion and receipt. The left LED flahe green to indicate the panel i tranmitting data. The right LED flahe yellow to indicate the panel i receiving data. LX-Bu Epanion 15.1 LX-Bu Header There are five LX-Bu header near the bottom of the XR150/XR550 panel: LX500 (J14), provide zone (all panel). LX600 (J9), provide zone (XR550 only). LX700 (J15 ), provide zone (XR550 only). LX800 (J17 ), provide zone (XR550 only). LX900 (J19 ), provide zone (XR550 only). Figure 9: LX-Bu Header and LED 15.2 LX-Bu LED The two LED, located above each LX-Bu header, indicate data tranmiion and receipt. The left LED flahe green to indicate the panel i tranmitting LX-Bu data. The right LED flahe yellow to indicate the panel i receiving LX-Bu data. 17

22 INSTALLATION 15.3 OVC LED The Overcurrent LED (OVC) light Red when the device connected to the Keypad Bu and LX-Bu(e) draw more current than the panel i rated for. The LED() turn a teady Red when lit. When the OVC LED() light red, the appropriate LX-Bu(e) and Keypad bu are hut down. The OVC LED located to the left of the 893A connector indicate overcurrent for the Keypad Bu (Terminal 7-10 and PROG header), XBUS, and LX500-LX700. The OVC LED to the right of the J24 Cell Module connector indicate overcurrent for LX800-LX900. J1 Ethernet Connector (Panel with Network/Encryption only) 16.1 Decription The Ethernet Connector i available on the XR150/XR550 with network or encryption to connect directly to an Ethernet network uing a tandard patch cable. The Ethernet Connector upport 100MB/ full duple operation and the maimum impedance i 100 Ohm Ethernet LED The two LED, located on the top edge of the J1 Ethernet Connector, indicate network connection. The right, Link LED light up green to indicate a valid receive connection from the hot network. The yellow LED light when connected to a 100Mb network and i off when connected to a 10Mb network. Figure 10: J1 Ethernet and LED 16.3 Network Tranient Suppreion The Model 270 Network Tranient Suppreion Module to provide tranient urge protection for the J1 Ethernet Connector. Refer to the Model 270 Intallation Sheet (LT-1316) for complete information. J3 Telephone RJ Connector 17.1 Decription Connect the panel to the public telephone network by intalling a DMP 356 RJ Cable between the panel J3 connector and the RJ31X or RJ38X phone block. The maimum impedance i 100 Ohm. CAUTION - To reduce the rik of fire, ue only No. 26 AWG or larger telecommunication line cord, uch a DMP Model 356 Serie Phone Cord J10 893A or 277 Trouble Sounder Connector Connect an 893A Dual Phone Line Module or Model 277CAN Trouble Sounder to J10 on the XR150/XR550 Serie. Refer to the 893A Intallation Sheet (LT 0135) or 277CAN Intallation Sheet (LT-1304CAN) for complete information Notification The uer mut not repair regitered terminal equipment. In cae of trouble, immediately unplug the device from the telephone jack. The factory warranty provide for repair. Regitered terminal equipment may not be ued on party line or in connection with coin telephone. No tify the telephone company with the following information: The particular line() where the ervice i connected Thi Cla A digital apparatu complie with Canadian ICES-003. The ringer equivalence number (REN) of 0.0 The device make, model, and erial number 17.4 Phone Line Monitor The XR150/XR550 Serie panel ha a built-in telephone monitor that monitor the phone line voltage to verify the connection to the central office. Figure 11 and the table below identify the phone block pin layout, wire number, and color. Wire Number Wire Color 1 Gray 2 Orange 3 Black 4 Red 5 Green 6 Yellow 7 Blue 8 Brown To Telephone Line Link LED Activity LED J1 The wire on the RJ31 that feed pin 4 and 5 hould be the ONLY wire on the D-marc. All other houe phone wiring hould be tied to pin 1 and 8 coming back from the RJ31. Dial tone mut come into RJ31X on pin 4 and 5 and go back to houe phone from pin 1 and 8. Follow thee tep Ring 7 8 ETHERNET Tip RJ31X or RJ38X Phone Block To Premie Phone Ring 1 Tip 1 Figure 11: Phone Jack Wiring 18