Stainless Steel Range

Transcription

1 PRODUCT MANUAL TR r2 Stainle Steel Range SSB, SSI, and SST Intallation, Operation, and Maintenance Manual PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

2 Warning Thi manual hould be read and undertood prior to intallation or operation of any Adveco SSB, SSI or SST tainle teel veel. Failure to read thi manual or follow it printed intruction may lead to peronal injury, damage to the veel and damage to the water heating intallation. Thee intruction hould be kept in a afe and acceible place near the veel. Veel hould be tored in a afe place prior to intallation to prevent damage. Copyright 2018 Adveco Ltd. All right reerved. No part of thi publication may be copied, reproduced, altered and/or publihed by any mean without the prior written approval of Adveco Ltd. Any brand name mentioned within thi publication are regitered trademark of their repective owner. Adveco Ltd. reerve the right to modify pecification in thi manual at any time and without notification. Adveco Ltd. accept no liability for third party claim ariing from unauthoried ue and/or ue other than a directed within thi manual. How to Ue Thi Manual All general information, intruction and pecification lited within thi manual applie to the full range of SSB, SSI and SST veel. Any information relevant to only pecific SSI or SST veel i contained within dedicated ection and i clearly identifiable by ection title. All information unle otherwie tated i applicable to intallation in any country. Any information that i relevant to a particular country only i eparated and located within clearly marked ection. For any querie or iue not covered by the cope of thi manual, pleae contact the Adveco Technical Department uing the contact detail provided on page 26. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 2 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

3 Content Page Product Decription 4 Intallation Intruction 1. Reponibilitie of the Uer 5 2. Reponibilitie of the Intaller / Deigner 6 3. Requirement of the Intallation 6 4. Location & Handling 7 5. Tank Connection 8 6. Primary Pipework 9 7. Secondary Pipework Dicharge Pipework Secondary Return Pipework Shunt / Detratification Pump Multiple Tank Control 15 Maintenance Operation 16 General Specification 17 Flange Specification 18 Further Specification: SSI and SST (Bottom Coil Only) 19 Further Specification: SST (Top Coil Only and Combined Coil) 20 Technical Drawing 1. SSB Buffer Veel and SSI Indirect Veel SST Twin-Coil Veel and SST Combined Coil Veel SSB-E Electric Veel Option SSB-D Direct Veel 24 Spare and Ancillary Item 25 Contact Detail & Warranty Information 26 3

4 Product Decription Adveco Stainle Steel Cylinder: SSB, SSI, SST Adveco Stainle Steel Cylinder are a veratile, modular range of dometic hot water veel that can be fitted with up to two high-capacity tainle teel indirect heating coil or pecialied flange and immerion heater a required by the application. The range i divided into three type of veel depending on the number of heat exchange coil included: Stainle Steel Buffer (hereafter SSB ) veel are upplied with two blank flange and zero heat exchange coil, and primarily erve a buffer veel only. Stainle Steel Indirect (hereafter SSI ) veel are upplied with one heat exchange coil fitted into the lower flange of the tank, with a blank flange fitted into the top. Stainle Steel Twin-Coil (hereafter SST ) veel are upplied with two heat exchange coil that can either operate independently or be connected together to erve a ingle high-capacity heat ource. The full range of tainle teel veel are compatible with direct heating option by the incluion of the Adveco range of electric immerion heater. Two ubtype of the SSB range are alo available by ubtiting one or both tandard blank flange for alternative pecialied flange: The Stainle Steel Buffer Electric (hereafter "SSB-E" or "SSB-E2" depending on the number of electric flange included) feature one to two electric element mounting flange, each capable of houing one or two Adveco electric immerion element. Thi make it poible for multiple immerion heater to be combined with a ingle tank, reulting in a highly adaptable electric water heater to erve dometic hot water ytem. The Stainle Steel Buffer Direct (hereafter "SSB-D") range feature a direct veel connection flange in place of the lowet blank flange, allowing the tainle teel veel to be ued a a buffer with a direct connection to a water heater. The Technical Drawing located on page can be conulted for a viual reference to the variou veel within the Adveco Stainle Steel Cylinder range. The Adveco Stainle Steel Cylinder range i deigned, manufactured, and teted in the EU to the requirement of: The Preure Equipment Directive EN 12897:2016 The cope of EN 12897:2016 cover indirectly heated, main preure torage water heater, with or without immerion heater backup, up to 1000 litre and 10 bar. The SSB, SSI and SST range of tainle teel veel up to 1000 litre have been produced to the requirement of thi tandard. Veel with torage capacitie of 1000 litre and greater have been deigned and manufactured within the pirit of thi tandard, and have been type teted in accordance with ection 6.2. Production unit in thi category are teted to ection 6.3. Thi upport the requirement for ound engineering a precribed by the Preure Equipment Directive for veel covered by Article 3, Paragraph 3. The full range of tainle teel veel are WRAS approved product, with approval reference Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 4 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

5 Intallation Intruction 1. Reponibilitie of the Uer Hot water ytem poe a potential rik for building occupant regarding temperature and biological rik. It i the reponibility of the building controller to ae the rik to the occupant of calding or Legionella and put in place uitable tep to protect the occupant. The rik aement mut be carried out by omeone uitably qualified. The following document offer guidance and aitance on reponibilitie: ACOP L8, 2014 HSG274 Part 2 Health and Safety at Work Act Workplace (Health, Safety and Welfare) Regulation HTM Part A and B Building Regulation Part G BS EN 806 All part CEN/TR And any other tandard, law, guideline, or rule in force in the location of the intallation, pat or future, that are current at the time of intallation. Thi intallation manual complement thee rule and mut not be conidered to override them in any way. Following the commiioning of a ytem and in compliance with the procedure and advice contained within thi manual, reponibility lie with the building controller to maintain a afe tandard of operation and regular maintenance procedure a required by the rik aement. Thi include enuring that the unit i not operated at temperature or preure in exce of thoe tated on the veel data plate. Nor hould the veel be expoed to a full or partial vacuum, uch a can be preent during draw-off or drainage of the unit while the cold feed or vent are cloed or obtructed. Failure to maintain a minimum of annual maintenance may void any and all warrantie. Full maintenance procedure hould only be carried out by a uitably qualified peron. Baic maintenance regime, a determined through rik aement, hould be carried out by the uer a directed on page 16. Adveco Ltd. advie that heating ytem in unoccupied premie, or that are ubjected to long period of hutdown, hould be drained down according to the procedure on page 16, to remove the rik of failure and/or damage occurring while the ytem i not being monitored. 5

6 Intallation Intruction 2. Reponibilitie of the Intaller / Deigner In compliance with the procedure and advice contained within thi manual, reponibility lie with the intaller to enure that the veel are correctly and afely intalled in line with all local regulation and law. In all cae, the relevant law and regulation take precedence over the intruction contained within thi manual. 3. Requirement of the Intallation The SSB, SSI, and SST range of tainle teel veel are uitable for ue with torage or heating of potable water in intallation up to a maximum preure of 6 bar. Any unvented cylinder intallation hould be notified to Building Control. Thi i bet done through a Competent Peron Scheme by intaller holding a valid unvented dometic hot water ticket. The following document et out the tandard of intallation that mut be adhered to: EN 806 All Part EN 8558:2015 Note that the intallation of any electric heating element require the ue of an earthed power upply. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 6 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

7 Intallation Intruction 4. Location & Handling Suitable method of moving a veel include the ue of a forklift truck where the veel i ecurely fixed to a pallet capable of upporting it weight, or by boom crane uing adequate textile ling of uitable capacity to lift the weight of the tank. Veel hould not be lifted uing the inulation, by chain, or by trap that may damage the inulation, connection, or wall of the tank. Care hould be taken when moving or lifting to minimie the rik of damage to the veel. The veel mut be located inide the building and poitioned on a level bae capable of upporting the unit when full. Floor loading calculation hould include the total filled weight, being equivalent to the um of the empty weight of the veel and the weight of any intalled coil or flange, plu the water volume in litre (where 1 litre of water weigh 1 kg). For tank and coil weight, conult page The veel hould be poitioned to provide uitable clearance a hown below in figure 1, and hould permit acce for viual inpection and maintenance of all connection and fitting. Conideration hould be given to the inpection, removal and replacement of any flange, heating coil, immerion heater, thermotat, and afety valve preent, a well a replacement of the entire veel. Any water torage veel require ome proviion againt damage to urrounding infratructure, electronic, and equipment in the event of a leak, damage, or veel failure. Acceptable method of protection include uitable bunding, gulley, drainage, or a leak detection and warning ytem. Tank up to 500 litre are provided with the inulation jacket already fitted to the veel. The inulation jacket can be removed if neceary to move the veel into location, but mut be replaced before the cylinder i piped up. Tank from 800 litre and above may be upplied with the inulation jacket eparately. Thi mut be intalled on the tank prior to the connection of any pipework. 500mm * Min. 1m 500mm 500mm * Figure 1: Working Clearance * Clearance on one ide of the veel may be reduced o long a there i acce with uitable clearance to the back or other ide of the unit. 7

8 Intallation Intruction 5. Tank Connection h h t&p t&p b2 b2 e y b1 b1 c c Connection and ize Port Purpoe Model Unit c h y e t&p b1 b2 Cold inlet Include drain connection. Can be ued a econdary return connection for SSI tank, and for SST tank when coil are combined. Hot outlet If ued a a preheat, there mut be a preure relief valve after the hot iolation valve. Optional econdary return Can be ued for SST tank when the top coil i fed by a boiler, and the bottom coil by renewable. Senor and extra connection Coil thermotat, enor, BMS connection, etc. Coil inpection hatch Can alo erve a an optional immerion heater connection Temp. & preure relief valve ¾'' or 1'' dependent upon heat input. Lower flange port For further information on option, pleae conult page Upper flange port For further information on option, pleae conult page Front Side Figure 2: Standard connection and poition for the Adveco tainle teel range inch inch inch inch DN180 DN180 DN180 DN180 DN180 DN180 inch, mm inch mm mm For connection height and veel dimenion conult page Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 8 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

9 Intallation Intruction 6. Primary Pipework The tainle teel range of indirect tank are produced with flange for up to two removable coil, leading to three ditinct product range depending on the number of coil intalled. The SSB Stainle Steel Buffer range i provided with blank flange and no coil intalled. The SSI Stainle Steel Indirect range i upplied with a ingle coil mounted in the lower flange, and the SST Stainle Steel Twin-Coil range i provided with coil fitted into both flange. A a reult, the tainle teel range can cater for mot hot water application. The coil fitted within the SST can be ued individually for two different heat ource, or can be combined by external, additional pipework (not upplied) to give a larger capacity ytem. With thee combination the veel can be ued a a preheater, afterheater, buffer or tandalone water heating ytem. Connection to the veel hould be made according to the location and ize denoted on page 8 and 17. All pipework hould be of an appropriate, non-corroive material, and hould be upported outide of the veel to prevent exceive load bearing upon the tank connection point. Pipework hould be arranged to facilitate uitable acce to ytem component. Any flanged connection to the veel mut be tightened in a diametrically oppoed equence to prevent uneven load acro the connection. While intalling pipework, conideration hould be given to removal of the coil for maintenance and cleaning of the tank. Valve and union type fitting are required. A drainage connection hould be included downtream of the union fitting. SST Combined Coil For larger capacity ytem with one heat ource, the two heating coil can be combined. The tandard way to do thi i in erie o that the primary flow through the top coil and then through the bottom coil. To etimate the total kw capacity with both coil, baed on an 80 C primary temperature, add the kw capacity for the top coil at 80 C to the kw capacity for the bottom coil at 70 C. For technical detail on kw capacitie at 70 C, on different temperature, or if a more accurate calculation i required, pleae contact the Adveco Deign Department. SST Separate Coil In the cae of two heat ource, the lower grade heat or le cotly energy ource hould go into the bottom coil to act a a preheat. The more reliable ource of high grade heat (uually a boiler) hould be piped into the top coil. Air Relief Each coil ha a 3/8 inch connection for an air bleed point to commiion the coil. Air relief valve are not upplied a tandard. 9

10 Intallation Intruction 7. Secondary Pipework General A tandard intallation will include the tainle teel cylinder a part of a main-fed ytem. The pipework hould be correctly ized to carry the maximum imultaneou demand of hot water for the building. Thi may or may not be the ame ize a the cold feed connection. Cold Feed All cold feed pipework mut be fitted with afety equipment to prevent overpreure and allow for the expanion of hot water in the ytem. Thi mut include a check valve and a preure relief valve et normally to the maximum working preure of the tank, but no more than 1.5 bar higher than the maximum working preure in line with the regulation et out in EN 8558 ection All main-fed ytem hould additionally include a preure reducing valve and trainer. The tandard kit upplied by Adveco ha a variable preure reducing valve with etting available between 1 bar and 5.5 bar. The dometic hot water preure mut exceed the primary ytem preure at all time to protect againt contamination of the DHW in the unlikely event of a leak from the coil. There mut not be any type of iolation between the preure relief valve and the veel. Safety equipment hould be intalled at the cold inlet unle otherwie pecified. The cold feed equipment hould be upplied a part of an unvented kit by Adveco Ltd., incluive of an expanion veel and temperature and preure relief valve with a preure etting at leat 0.5 bar above the preure relief valve etting but no more than 1.5 bar higher than the maximum working preure of the tank, in line with EN 8558 ection A 3/4 inch valve i uitable for ue with mot indirect ytem. The expanion veel hould be calculated to be roughly 5% of the total hot water ytem volume for ytem operating at around 3 bar. Pleae contact the Adveco Deign Department to obtain a full calculation if required, or for high preure application. The expanion veel preure mut be et equal to the cold fill preure of the ytem, and mut be et with no preure on the wet ide of the membrane. The expanion veel mut be ituated on the cold feed pipe. For tank arranged in erie, only one expanion veel hould be ued at the beginning of the ytem. Conideration may be given to flow-through type expanion veel for ytem identified a high rik. The expanion veel branch can have a lock hield valve o long a the relief valve i not on the ame branch. For further note on tank and pipework arrangement, pleae refer to the Technical Drawing found on page of thi manual. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 10 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

11 Intallation Intruction 7. Secondary Pipework Drain The cold feed i located at the lowet part of the cylinder to meet anti-legionella requirement. A drain hould be intalled in the cold feed at the lowet point, before the connection to the cylinder. The drain valve hall be of uitable ize to allow draining of the tank in a reaonable amount of time. It i recommended that a 1/4 turn lever valve and plug or cap are ued and that the valve ize be one ize maller than the cold feed connection ize. A uitable drain or gulley hould be provided to allow draining of the tank. Vented Intallation: In cae of a vented ytem the unvented kit can be omitted. From the hot flow there mut be an uninterrupted open vent with no valve, of at leat 19mm internal diameter, reaching above the water level of the cold water tank and dicharging to a afe place (not into the cold tank). It i conidered good practice to fit a temperature and preure relief valve even on a vented ytem. 11

12 Intallation Intruction 8. Dicharge Pipework Dicharge from relief valve Figure 3: Dicharge pipework diagram (a found in Building Regulation Part G). Dicharge pipework requirement for the UK are found in Building Regulation Part G. They are ummaried here but it i recommended to read the regulation in full at D1, the pipe from the relief valve to the air break, mut have the ame diameter a the valve, mut be metal, and mut be no longer than 600mm. An airbreak, uch a a tundih or a funnel, mut be intalled at the end of D1. D2, the pipe from the air break to termination, mut be at leat one ize larger than D1, mut have at leat 300mm vertical drop before a bend, and mut have a continuou fall. It hould typically be metal, but PP i acceptable (note: PP i puh-fit platic. ABS and PVC olvent welded platic are not uitable). If D2 i longer than 9m total equivalent length (baed on 1.4m per bend), then it diameter mut be increaed. Pleae refer to Building Regulation G3 at If a number of D2 pipe are combined, the diameter of the common pipe hould be one ize larger than the bigget D2 pipe. D2 hould be terminated in one of the following way: Into a oil tack, uitable for the temperature, with a mechanical eal, and with no anitary appliance on it and a warning not to ue the pipe for anitary appliance. Into a trapped gulley with the pipe end below the grate but above the water eal. Terminating at low level to a uitable external ground level urface with a guard around the pipe end and that end within 100mm of the ground At high level into a uitable hopper or onto a roof that can withtand the temperature and doe not have platic guttering within 3m of the dicharge and doe not create a rik to people below. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 12 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

13 Intallation Intruction 9. Secondary Return Pipework A econdary return i the bet way to enure that there i hot water at the outlet in a hort amount of time. In ome cae thi could be done with trace heating, but the amount of electricity neceary to do thi mut be conidered. In ome mall ytem it i not neceary to ue either, and the hot water can flow directly to the tap. The water at the furthet outlet mut be 50 C within one minute (55 C in healthcare premie), although thi may not be acceptable to all uer and a econdary return arrangement hould be conidered for waiting time of longer than 20 econd. In all cae, ite legionella protection policy take precedence over thi document. The econdary return pump hould be ized to give a uitable flow of hot water around the ytem to enure the returning temperature i at leat 50 C. The pipework mut be inulated. The pump mut have a check valve on the poitive ide of the return pump to prevent cold flow to the hot outlet. For SSB and SSI veel application, the econdary hould return into the cold feed of the water heater. For the SST Twin-Coil range, the econdary hould enter the hot water ytem above any low grade heat ource, jut before the final high grade heat ource. For a tandard indirect water heater intallation where both coil are connected together from one heat ource, the return hould go into the cold feed downtream of the unvented kit / inlet combination afety group. In cae where two heat ource are ued, the econdary return hould be piped into the centre of the tank. 10. Shunt / Detratification Pump In intallation where the econdary return i piped into the cold feed, it may be conidered that all requirement for detratification or purging are met. Thi mut be confirmed by ite Legionella rik aement. In intallation without econdary return, or when it i piped into the centre of the tank, it i advied that the tank i entirely heated to 60 C for at leat one hour per day. Thi hould be done with a detratification pump piped from the outlet to the inlet. It hould be timed with a clock to run at a low demand period of the day, while the heat ource i on, for long enough that the bottom of the tank will achieve 60 C for one hour. In intallation with multiple heat ource, a detratification pump hould not run permanently. For buffer veel application, the hunt pump between the buffer outlet and the water heater inlet hould be timed to be the ame a the water heater. 13

14 Intallation Intruction 11. Multiple Tank In cae of a multiple tank ytem the following mut be adhered to: Serie Tank Serie tank are ued in intallation a preheater and afterheater. A low grade or renewable heat ource i ued to heat the preheat and the water i tranferred to the afterheater, where the additional energy required will top up the temperature. The afterheater i deigned to be able to upply the entire load if neceary, and it i alway kept up to temperature while the building i occupied. 1. The unvented kit (with an expanion veel ized for the entire ytem) or inlet combination group hould be intalled on the cold feed ide of the preheat veel. 2. The econdary return hould be piped into the inlet of the afterheater. 3. A purge pump hould be intalled from the afterheater outlet to the preheater inlet to allow for thermal diinfection of the preheat. Thi can be on a timer or on a control ytem to heat the preheat to 60 C a often a required by the rik aement a referenced on page The afterheater mut have a temperature and preure relief valve. If it i deirable to be able to drain one tank without affecting the other, an iolation valve can be intalled between the two tank only if another preure relief valve i intalled on the afterheater ide of the valve. No check valve or expanion veel hould be intalled between the preheater and afterheater. Parallel Tank 1. All pipework including the econdary return to parallel tank hould be balanced either by pyramid or by revere return. 2. It i bet if each tank ha it own unvented kit / inlet combination group to allow for eay ervicing of each unit. Conideration hould be given to one common preure reducing valve to enure equal preure and flow through each tank. 3. The econdary return hould connect into each cold feed. SSB Buffer Tank 1. Where a buffer veel i preent, all hot water flow into the building mut come from the buffer. 2. The cold feed hould connect into the water heater. 3. The output from the water heater hould connect into the bottom of the buffer veel. 4. It i advied to include a hunt pump, from the buffer outlet to the inlet of the water heater. 5. An unvented kit / inlet combination group hould be intalled on the water heater, with a temperature and preure relief or inlet combination ecurity group valve on the buffer veel. 6. The econdary return from the building hould pa into the cold feed of the water heater. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 14 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

15 Intallation Intruction 12. Control Every hot water veel mut be fitted with a method of temperature control. Thi can either be a control thermotat in the tank, a enor, or a differential control between the tank temperature and the heat ource. Thi mut be et to enure a water temperature of at leat 60 C throughout the veel. The temperature control etting hould be ubject to a rik aement in accordance with local building regulation. In mot cae, it i recommended to fit thermotatic mixing valve on all outlet for peronal ue. The temperature control method hould be et to provide a water temperature at outlet of at leat 50 C (55 C in healthcare premie) within one minute, and a minimum return temperature of 50 C. Every veel that contain a heat ource mut additionally be fitted with a non-elf-reetting overheat thermotat capable of preventing heat entering the tank from all ource, by either topping the primary flow or by turning off the heat ource. Stopping the primary flow may be achieved by a pring-loaded zone valve, or by turning off the pump, providing that thermoyphoning cannot occur. Time control It i acceptable to hut off the hot water ytem if the building i unoccupied for a hort period over night or on the weekend. Following a hort hutdown, the hot water ytem mut come on long enough before occupation o that it ha been up to temperature for at leat one hour. Longer hutdown mut be rik aeed and may require fluhing and diinfection before tartup. Frot protection In normal working operation, the tank i protected againt frot becaue it will be maintained at temperature. In ituation where it will be hut down becaue the building i unoccupied, conideration mut be given to freezing of the water within the tank and pipework. Thi i bet dealt with by a frot thermotat (not upplied a tandard) in the room to bring on the heat ource and econdary pump at 5 C. 15

16 Maintenance Operation Hot water ytem maintenance hould be determined by the building rik aement and legionella protection policy. While full maintenance and cleaning of tank hould be carried out by a trained operative, there are regular hot water ytem maintenance check that mut be carried out more frequently and can be done by the building controller nominated peron. Thee include monthly check of the hot water temperature and regular fluhing of low ue outlet. The more involved maintenance regime of a tank will vary from ite to ite depending on water condition and ue. Maintenance mut take place at leat yearly, but more frequent viit may be required depending on the condition of the unit after one year. The main reaon for frequent maintenance i due to cale formation in the tank. Conideration hould be given to cale control in hard water area to reduce decale frequency. The maintenance of a tank involve checking the ytem and cleaning the tank. Check to carry out: Temperature i correct and above 60 C. Return temperature i above 50 C and in line with relevant local regulation. Furthet outlet temperature i above 50 C (55 C for healthcare) in 60 econd. Control tat i calibrated and correctly hut off heat ource. Overheat tat i functional and top heat to the tank. Relief valve operate and dicharge correctly. All valve travel free. The ytem ha no leak. The preure of any expanion veel on the cold feed pipework i equal to the cold feed preure (checked when there i no preure on the water ide of the diaphragm). Cleaning: All filter hould be cleaned. The tank hould be drained down, cleaned and decaled. All heater batterie hould be decaled. Drainage Procedure: Turn off all direct or indirect heat ource connected to the veel. Turn off any ytem pump and iolate all connection to and from the veel. Enure that the veel drain connection i connected to, or poitioned over, a drain or gulley. For preuried ytem, open the drain valve connection to releae the preure within the veel. Open a afety valve or remove an automatic air vent connection on the tank* to allow air into the unit and prevent negative preure build-up during drainage. Alternatively, enure there i no iolation between the DHW outlet of the tank and a draw-off point, and open the tap. Allow the water in the pipework to drain, and leave the tap open to allow ingre of air to the veel. Allow the veel to fully drain via the drain valve connection. *Note that the air vent connection located on the flange of SSI and SST tank only connect to the heating coil, not the water cylinder itelf. Note that for SSI and SST veel, the indirect heating coil may alo need to be drained. Thi hould be done via a drainage point included on the primary pipework. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 16 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

17 General Specification Do Di h h t&p t&p e b2 b2 y b1 b1 c c Front A B C E F G Figure 4: Standard veel dimenion and connection height. Side Dimenion Model Unit Volume (SSB range only) L D o Diameter (Outer) mm D i Diameter (Inner) mm A Cold inlet height mm B Lower flange height mm C Inpection flange height mm E Upper flange height mm F T&P height mm G Veel & hot outlet height mm Empty ma kg Veel inulation: 100mm flexible polyurethane, thermal conductivity λ = W/m C Standing loe kwh/24h All threaded connection are BSPP female unle otherwie tated. 17

18 Flange Specification Flange I.D. Decription Size (mm) Ma (kg) Compatible veel Adveco C0/300 Blank flange SSB ; SSI ; SSBE Adveco C1.0/ m 2 heating coil SSI ; SST Adveco C2.25/300 Single 2.25'' immerion adapter SSBE ; SSBE M0129 Direct 2x 2.5'' flange plate SSB-D Adveco C0/380 Blank flange SSB ; SSI ; SSBE Adveco C1.5/ m 2 heating coil SSI ; SST Adveco C3.0/ m 2 heating coil SSI 800; SST 800 Adveco C2.25/380 Twin 2.25'' immerion adapter SSBE ; SSBE M0130 Direct 2x 3.0'' flange plate SSB-D Adveco C0/430 Blank flange SSB ; SSI ; SSBE Adveco C4.0/ m 2 heating coil SSI ; SST Adveco C5.0/ m 2 heating coil SSI ; SST Adveco C6.0/ m 2 heating coil SSI ; SST Adveco C2.25/430 Twin 2.25'' immerion adapter SSBE ; SSBE M0131 Direct 2x DN100 flange plate SSB-D All flange and heating coil are contructed from tainle teel. a f f r r Indirect heating coil - front Indirect heating coil - ide Direct heating flange (2.5''-3'') - front Direct heating flange (2.5''-3'') - ide p p f 15 r EARTH CONNECTION '' Single Immerion Adapter - ide 2.25'' Dual Immerion Adapter - ide 2.25'' Immerion Adapter - ide Direct heating flange (DN100) - front Direct heating flange (DN100) - ide Figure 5: Drawing of available tainle teel flange deign, where: f: Flow inlet: Primary flow connection for indirect coil or direct flange r: Return outlet: Primary return connection for indirect coil or direct flange a: Heating coil air relief: Air relief point on heating coil p: 2.25'' immerion heater port: For ue with SSB-E range electric immerion element Connection: Flange Unit Flange outer diameter mm Blank flange n/a n/a n/a n/a n/a n/a n/a n/a n/a f: primary flow inch Indirect heating coil r: primary return inch a: coil air relief ⅜ ⅜ ⅜ ⅜ ⅜ ⅜ ⅜ ⅜ inch Direct flange f: primary flow DN100 DN100 DN100 DN100 inch/mm r: primary return DN100 DN100 DN100 DN100 inch/mm Electric flange p: immerion port 2 ¼ 2 ¼ 2 ¼ 2 ¼ 2 ¼ 2 ¼ 2 ¼ 2 ¼ inch Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 18 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

19 Further Specification: SSI and SST (Bottom Coil Only) Model SSI/SST 200/ / / / / /5.0 Unit Volume (SSI range only) L Volume (SST range only) L Nominal primary ΔT K Nominal capacity 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Coil preure drop at 80 C primary flow mbar Maximum coil preure bar Coil water volume L Coil urface area m 2 Coil flange ize mm Model SSI/SST 1500/ / / / / /6.0 Unit Volume (SSI range only) L Volume (SST range only) L Nominal primary ΔT K Nominal capacity 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Coil preure drop at 80 C primary flow mbar Maximum coil preure bar Coil water volume L Coil urface area m 2 Coil flange ize mm Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 19 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

20 Further Specification: SST (Top Coil Only and Combined Coil) Model SST 200/ / / / / /5.0 Unit Volume (SST range only) L Nominal primary ΔT K Maximum coil preure bar Coil water volume L Coil urface area m 2 Coil flange ize mm SST: Top Coil Only Nominal capacity at 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Preure drop at 80 C primary flow mbar SST: Combined Coil Nominal capacity at 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Preure drop at 80 C primary flow mbar Model SST 1500/ / / / / /6.0 Unit Volume (SST range only) L Nominal primary ΔT K Maximum coil preure bar Coil water volume L Coil urface area m 2 Coil flange ize mm SST: Top Coil Only Nominal capacity at 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Preure drop at 80 C primary flow mbar SST: Combined Coil Nominal capacity at 80 C primary flow kw Primary flow rate at 80 C L/ DHW recovery L/hr DHW peak half hour flow L/hr DHW peak hour flow L/hr DHW peak two hour flow L/hr Preure drop at 80 C primary flow mbar 20

21 Technical Drawing Figure 5 (above): Example ytem chematic for Adveco SSB veel. Figure 6 (below): Adveco SSI veel. 21

22 Technical Drawing Figure 7 (above): Example ytem chematic for Adveco SST veel with two heat ource. Figure 8 (below): SST With one high capacity ource. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 22 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

23 Technical Drawing Figure 9 (above): Example ytem chematic for Adveco SSB-E veel. Figure 10 (below): SSB-E2 veel. 23

24 Technical Drawing Figure 11: Example ytem chematic for Adveco SSB-D veel featuring a direct connection to a generic water heater. Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 24 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

25 Spare and Ancillary Item Ancillarie Item Decription Adveco Unvented Kit Wide range of unvented kit available, including expanion veel and valve. Conult drawing on page for tandard component ¾'' Detratification Pump Kit Include check and iolation valve uitable for 22 mm pipework Adveco electric immerion heater kit Pre-wired immerion element upplied with gaket and 180 mm flanged connection. Include integrated pocket plu control and overheat thermotat. Contactor not included. All immerion heater are uitable for three phae electrical upplie. EB0014, EB0015, and EB0016/1PH are additionally uitable for ingle phae upplie Adveco electric immerion element 2 ¼'' BSP element upplied with control and overheat thermotat only All immerion heater are uitable for three phae electrical upplie. E0021 and E0022 are additionally uitable for ingle phae upplie Product Code Pleae contact Adveco for detail MB kw: EB kw: EB kw: EB0016, EB0016/1PH 12 kw: EB kw: EB kw: EB0019A 36 kw: EB0021A 18/9 kw dual-tage: EB kw: E kw: E kw: E kw: E0024 Spare Item Decription Product Code Inpection / mid-level flange fibre gaket without beam: 180/130 mm for ue with all veel from M0115 Blank / immerion flange fibre gaket without beam: 300/200 mm for ue with SSB/SSI/SSB-E/SSB-D M0116 Blank / immerion flange fibre gaket without beam: 380/300 mm for ue with SSB/SSI/SSB-E/SSB-D M0117 Blank / immerion flange fibre gaket without beam: 430/350 mm for ue with SSB/SSI/SSB-E/SSB-D M0118 Primary coil flange fibre gaket with beam: 300 / 220 mm for ue with SSI/SST M0119 Primary coil flange fibre gaket with beam: 380 / 300 mm for ue with SSI/SST M0120 Primary coil flange fibre gaket with beam: 430 / 350 mm for ue with SSI/SST M0121 Immerion heater flange gaket 180 mm - For ue with Adveco EB00## immerion heater kit E Immerion heater flange 180 mm - For ue with Adveco EB00## immerion heater kit (S) Single enor pocket long, chrome plated E Multiple enor pocket 120 mm, tainle teel E Control thermotat 0-95 C 1/2'' pocket mount E0008/0-95C Control thermotat C for ue within Adveco EB00## immerion heater terminal houing (up to 12 kw) E Overheat thermotat 90 C for ue within Adveco EB00## immerion heater terminal houing (up to 12 kw) E0044 Combined control and manual reet overheat thermotat for ue in conjunction with Adveco EB00## immerion heater from 18 kw. Combine with E or E pocket only. Non-elf reetting overheat thermotat 95 C capilliary type Temperature and preure gauge, C. 0-6 bar, 80 mm dial 1/2'' elf-ealing wet pocket mount Machine crew m12 x 40mm hex ocket cap tainle teel E0010 E0009 M0011 M0136 Figure 12: Left: Gaket without beam Right: Gaket with beam for ue with indirect heating coil only 25

26 Contact Detail & Warranty Information The Adveco SSB, SSI, SST range, thi manual, and all information contained within, are upplied by Adveco Ltd. UK Adveco Ltd. Unit 7&8 Armtrong Mall, Southwood Buine Park, Farnborough, Hamphire, GU14 0NR T: The Adveco SSB, SSI, SST range i provided with a 5 year veel warranty reliant upon the following condition: The veel i correctly and afely tored, intalled, and ued a intructed by thi manual. The veel i filled excluively with potable water. The dometic hot water ytem i kept in a good condition and i uitably maintained, incluive of maintenance of the veel a directed on page 16 of thi manual. The veel ha not been altered, tampered with, and ha not been ubjected to damage from frot, vacuum, or external influence. Excluion to warranty condition include: Conequential damage ariing from malfunction, failure, or leak aociated with the veel. Failure or damage of the veel or dometic hot water ytem ariing from the build up of exceive cale. Any part and labour charge aociated with maintenance, repair, or replacement of the veel. For further information and warranty claim, pleae contact Adveco Ltd. through the addre lited above. Adveco Sale Department Adveco Spare Department T: Option 1 T: Option 3 E: Sale@adveco.co E: Spare@adveco.co Adveco Technical Department Adveco Deign Department T: Option 4 T: Option 5 E: Technical@adveco.co E: Technical@adveco.co Adveco Service & Commiioning Department T: Option 6 E: Service@adveco.co Stainle Steel SSB, SSI, SST range - Intallation, Operation, and Maintenance Manual 26 PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS

27 Note 27

28 Adveco alo offer the following product and ervice: Bepoke ytem deign Maintenance and ervice package Buffer tank Indirect and direct hot water ytem Off ite manufacturing of kid and plant room Control Sytem Packaged plate heat exchanger Solar thermal ytem Ga fired heating ytem Combined heat & power cogeneration ytem Adveco Ltd. Unit 7&8 Armtrong Mall, Southwood Buine Park, Farnborough, Hamphire GU14 0NR Company Reg : T : E : enquirie@adveco.co I : PRACTICAL, EFFICIENT & SUSTAINABLE BUILDING SERVICES SOLUTIONS