Thermozone ADR 200/300 E/W

Transcription

1 R Thermozone ADR 200/300 E/W Electrical heat 9-18 kw Water heat Lengths: 1, 1,5 and 2 metres Thermozone ADR 200/300 E/W Recessed air curtains for doors heights up to 3,5 metres ADR is our air curtain for recessed mounting in false ceilings over entry doors and other smaller doors with heights of up to 3,5 metres. The only visible part of the unit is the discretely placed air intake and air blower grilles. ADR creates an air barrier that effectively prevents cold draughts and ensures a comfortably warm environment. Major savings are made by the elimination of energy losses through openings. An adjustable air blower grille allows you to control the air flow to achieve an optimal air curtain effect. An ADR is fitted with a heater battery for either electricity or water that compensates for any cold air that may force its way in through the door despite the air curtain. The air curtain can also contribute to heating the building when the door is closed. Water or snow inside the entrance is dried up effectively by the heated air from the air curtain. An ADR can also prevent odours, exhaust gases or insects from passing through the opening. Where the openings are wide, it is possible to mount several units side by side and control them using a single thermostat and control panel. The different product lengths make it possible to cover openings of different widths. Mounting in false ceilings means that only the intake and air blower grilles are visible. Corrosion proof housing made of hot zinc-plated and powder coated steel panels. Colour: RAL Simple suspension using fixed nuts on the top for mounting with threaded rod. The design of the intake air grilles makes separate dust filters superfluous. The air intake and air blower grilles in telescopic design are easily adjusted to suit the false ceiling. An adjustable air blower grille allows you to direct the airflow for an optimal air curtain effect. Air velocity profile For other recessed versions, please see 78 Design and specifications are subject to change without notice.

2 Technical specifications Thermozone ADR 200/300 E with electrical heat 3 steps t* 1 [ C] Sound level* 2 [db(a)] Voltage [V] Amperage [A] (control) Voltage [V] Amperage[A] (heat) Length ADR210E 0/6/9 700/ /19 40/57 230V~/1,6A 400V3~/13A ADR215E 0/8/ / /17 43/60 230V~/2,3A 400V3~/17,5A ADR220E 0/12/ / /19 44/60 230V~/3,1A 400V3~/26A ADR310E 0/6/9 950/ /14 44/61 230V~/2,2A 400V3~/13A ADR315E 0/8/ / /14 43/60 230V~/2,3A 400V3~/17,5A ADR320E 0/12/ / /15 45/62 230V~/3,9A 400V3~/26A * 1 ) t = temperature rise of passing air at maximum heat output and lowest/highest airflow. * 2 ) Conditions: Distance to the unit: 5 metres. Directional factor: 2. Equivalent absorption area: 200 m 2. [mm] Weight [kg] Technical specifications Thermozone ADR 200/300 WL with water heat, heating coil for low temperature water < 80/60 C 2 * 1 t* 1,2 [ C] Water volume [l] Sound level* 3 [db(a)] Voltage [V] Amperage [A] Length [mm] Weight [kg] ADR210WL / /31 1,7 40/57 230V~ 1, ADR215WL / /33 2,7 43/60 230V~ 2, ADR220WL / /33 3,8 44/60 230V~ 3, ADR310WL / /30 2,1 44/61 230V~ 2, ADR315WL / /33 3,2 43/60 230V~ 2, ADR320WL / /34 4,4 45/62 230V~ 3, Technical specifications Thermozone ADR 200/300 WH with water heat, heating coil for high temperature water 80/60 C 2 * 1 ADR210WH 8 680/ /19 0,8 40/57 230V~ 1, ADR215WH / /18 1,3 43/60 230V~ 2, ADR220WH / /18 1,5 44/60 230V~ 3, ADR310WH / /21 1,0 44/61 230V~ 2, ADR315WH / /24 2,2 43/60 230V~ 2, ADR320WH / /21 3,0 45/62 230V~ 3, * 1 ) Applicable at water temperature 80/60 C, air temperature +15 C. * 2 ) t = temperature rise of passing air at maximum heat output and lowest/highest airflow. * 3 ) Conditions: Distance to the unit: 5 metres. Directional factor: 2. Equivalent absorption area: 200 m 2. Protection class ADR200/300 E/W: (IP23). t* 1,2 [ C] Water volume [l] Sound level* 3 [db(a)] Voltage [V] Amperage [A] Length [mm] Weight [kg] CE compliant. 79

3 Dimensions L L/ M Connection dimensions, inside thread Ø ADR210WL ADR215WL ADR220WL ADR200WH ADR300WL ADR300WH 3/4 3/4 DN15 DN20 Positioning, mounting and installation Mounting ADR is fitted with fixed nuts (M8) at 6 points (9 points for the 2-metre model), on the top for suspension using a threaded rod. When the space is limited, the telescopic inlet/outlet extension may be removed. The lower part of the air curtain is then mounted level with the false ceiling. 80

4 Control kits Electric 3 Level 1 is controlled manually. Room thermostat controls the heat output in 2 steps. Control kit CK01E: - CB32N, control box, controls the airflow in 3 steps and heat output in 2 steps - RTI2, 2-step room thermostat Level 2 and heat output are controlled automatically based on the opening of the door and the room temperature. When the door is open the fan runs on high speed, when the door closes the fan will continue to run for the desired time (2s 10 min.) set on MDC. When the door is closed the fan runson low speed if there is a need for heating, if not the fan is switched off. The room thermostat controls the heat output. E.g. the thermostat is set on 23 C and the difference between the stages 4 C. The thermostat will activate below 19 C when the door is closed. When the door opens, the thermostat will activate below 23 C and normally the heat is switched on. Control kit CK02E: - CB32N, control box, controls the airflow in 3 steps and heat output in 2 steps - MDC, magnetic door contact with time delay - RTI2, 2-step room thermostat Level 3 and heat output are controlled automatically based on the opening of the door, outdoor temperature and the room temperature. The system is based on an advanced microprocessing regulator in an attractive design. All parameters are pre-programmed for easy and quick installation. Control kit CK03GD: - ADEA, regulator (complete with outdoor sensor, built in room sensor and door contact) - ADEAIS, indoor sensor - ADEAEB, control board, for external mounting - ADEAGD1, additional electric board Shop entrance, Netherlands ADR200/300 Read more about operation and usage of ADEA in chapter on Controls and accessories. See also chapter on Controls and accessories or contact Frico for more options. 81

5 Water 2 Level 1 is controlled manually. Room thermostat controls the heat output via actuator/valve on/off. Control kit CK01W: - CB30N, control box, controls the airflow in 3 steps - T10, room thermostat IP30 Note! A set of valves VR20 or VR25 or actuator+valve SD20+TVV20 or TVV25 should be added for a complete control kit.) Level 2 and heat output are controlled automatically based on the opening of the door and the room temperature. When the door is open the fan runs on high speed, when the door closes the fan will continue to run for the desired time (2s 10 min.) set on the MDC. When the door is closed the fan runs on low speed if there is a need for heating, if not the fan is switched off. The room thermostat controls the heat output on/off. E.g. the thermostat is set on 23 C and the difference between the steps 4 C. The thermostat will activate below 19 C when the door is closed. When the door opens, the thermostat will activate below 23 C and normally the heat is switched on. Control kit CK02W: - CB30N, control box, controls the airflow in 3 steps - MDC, magnetic door contact with time delay - RTI2, 2-step room thermostat Note! A set of valves VR20 or VR25 or actuator+valve SD20+TVV20 or TVV25 should be added for a complete control kit. Level 3 and heat output are controlled automatically based on the opening of the door, outdoor temperature and the room temperature. The system is based on an advanced microprocessing regulator in an attractive design. All parameters are pre-programmed for easy and quick installation. Control kit CK03GD: - ADEA, regulator (complete with outdoor sensor, builtin room sensor and door contact) - ADEAIS, indoor sensor - ADEAEB, control board, for external mounting - ADEAGD1, additional electric board Note! A set of valves VR20 or VR25 or actuator+valve SD20+TVV20 or TVV25 should be added for a complete control kit. Read more about operation and usage of ADEA in chapter on Controls and accessories. See also chapter on Controls and accessories or contact Frico for more options. 82

6 charts water ADR200/300WH Incoming / outgoing water temperature 130/70 C ADR210WH max ,3 42 0,05 11,4 45 0,05 ADR215WH max ,5 41 0,07 16,2 44 0,07 ADR220WH max ,5 41 0,09 21,0 44 0,09 ADR310WH max ,5 46 0,08 17,3 49 0,07 ADR315WH max ,1 50 0,12 26,1 52 0,11 ADR320WH max ,2 46 0,14 32,9 49 0,14 Incoming / outgoing water temperature 110/80 C ADR210WH max ,7 43 0,11 11,8 46 0,10 ADR215WH max ,1 42 0,15 16,9 45 0,14 ADR220WH max ,1 41 0,19 21,6 45 0,18 ADR310WH max ,9 46 0,16 17,6 49 0,14 ADR315WH max ,1 51 0,24 27,1 54 0,23 ADR320WH max ,6 46 0,29 33,3 49 0,28 Incoming / outgoing water temperature 90/70 C ADR210WH max ,4 38 0,13 9,6 41 0,12 ADR215WH max ,9 37 0,18 13,6 40 0,17 ADR220WH max ,0 37 0,23 17,4 40 0,21 ADR310WH max ,5 41 0,19 14,3 44 0,18 ADR315WH max ,0 45 0,29 21,9 47 0,27 ADR320WH max ,2 41 0,36 26,9 44 0,33 Incoming / outgoing water temperature 80/60 C ADR210WH max ,6 34 0,11 7,8 37 0,09 ADR215WH max ,3 33 0,15 11,1 37 0,14 ADR220WH max ,7 33 0,19 14,2 36 0,18 ADR310WH max ,9 36 0,16 11,6 39 0,14 ADR315WH max ,8 39 0,24 17,8 42 0,22 ADR320WH max ,3 36 0,30 22,0 39 0,27 83

7 charts water ADR200/300WL Incoming / outgoing water temperature 80/60 C ADR210WL max ,0 46 0,17 12,7 48 0,16 ADR215WL max ,0 46 0,26 19,1 48 0,23 ADR220WL max ,5 44 0,31 23,1 46 0,28 ADR310WL max ,0 45 0,22 16,3 47 0,20 ADR315WL max ,3 48 0,32 24,0 50 0,29 ADR320WL max ,4 49 0,48 35,7 51 0,44 Incoming / outgoing water temperature 60/50 C ADR210WL max ,2 38 0,25 9,0 40 0,22 ADR215WL max ,4 38 0,37 13,5 40 0,33 ADR220WL max ,8 37 0,46 16,4 39 0,40 ADR310WL max ,2 37 0,32 11,6 39 0,28 ADR315WL max ,3 39 0,47 16,8 41 0,41 ADR320WL max ,9 40 0,70 25,2 42 0,61 Incoming / outgoing water temperature 60/40 C ADR210WL max ,5 34 0,10 7,1 36 0,09 ADR215WL max ,7 34 0,15 10,6 36 0,13 ADR220WL max ,5 33 0,19 13,1 35 0,16 ADR310WL max ,8 33 0,13 9,0 35 0,11 ADR315WL max ,1 35 0,19 13,6 37 0,16 ADR320WL max ,0 36 0,29 20,1 38 0,24 Incoming / outgoing water temperature 60/30 C ADR210WL max ,4 29 0,05 5,0 31 0,04 ADR215WL max ,5 29 0,08 7,3 31 0,06 ADR220WL max ,8 28 0,09 9,1 30 0,07 ADR310WL max ,0 28 0,06 5,5 29 0,04 ADR315WL max ,3 30 0,10 9,5 32 0,08 ADR320WL max ,0 31 0,14 13,8 32 0,11 84

8 Pressure drop water Water pressure drop over ADR 200/300 W water coil Pressure drop [kpa] Pressure drop [bar] The pressure drop is calculated for an average temperature of 70 C (PVV 80/60). For other water temperatures, the pressure drop is multiplied by the factor K. Average temp. water C K 40 1, , , , , ,93 Pressure drop [kpa] Pressure drop [bar] Water presssure drop over regulations and valves 0,1 1, ,7 Pressure drop [kpa] 10 0,1 Pressure drop [bar] VR20 TVV20 VR25 TVV25 1 0,01 0,1 1,0 0,01 85