CEN System - Delegated Decisions Dispatch 23:2017

Transcription

1 CEN System - Delegated Decisions Dispatch 23:2017 DDD Page 1 1 CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC CEN/TC 10 Decision CEN/TC /2016 taken on Subject: Adoption of a New Work Item CEN/TC 10 - Lifts, escalators and moving walks having considered the proposal for a new item as documented in CEN/TC 10 N 1259 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable TR 2. This item corresponds to The revision of a CEN/TR CEN/TR 115-3: Document CEN/TC 10/WG 2 - Escalators and moving walks

2 Page 2 4. Title Safety of escalators and moving walks - Part 3: Correlation between EN 115:1995 and its amendments and EN 115-1: Scope This technical report applies to escalators and moving walks built in accordance with EN 115-1: Environmental? 9. The project is Use of materials Use of checklist or expected CEN lead document from another organization 10. Track Vote on TS/TR by correspondence AFNOR SFS ASI SIS LST SN BSI SNV UNE DS UNI NEN IPQ 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 14 Number of negative votes: 0 Number of abstentions: 0

3 2 CEN/TC 19 Decision CEN/TC /2017 taken on DDD Page 3 Subject: Change of deliverable for a item neither mandated nor covered by an Order Voucher CEN/TC 19 - Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and biological origin. having fully justified the need for a change of deliverable concerning item ; considering that the item covering the current deliverable is neither mandated nor covered by an Order Voucher; considering resolutions BT 34/2002, BT 42/2003 and related document BT N 6962 concerning timeframes for the development of ENs; decides to change the deliverable from EN to CEN/TS for WI " Liquid petroleum products - Determination of aerobic biological degradation of fully formulated lubricants in an aqueous solution - Test method based on O2-consumption ". The standstill on this item is released. The decision was taken by weighted vote and simple majority with 15 positive vote(s), 0 negative vote(s) and 19 abstention(s). Decision CEN/TC /2017 taken on Subject: 3 year time-frame for the development of WI month Tolerance Request. CEN/TC 19 - Gaseous and liquid fuels, lubricants and related products of petroleum, synthetic and biological origin. considering Resolution BT 34/2002 by which BT decided that any item to result in an EN, registered after , shall normally result in an EN after 3 years and set maximum times between well identified stages, as well as Resolution BT 42/2003 deciding on variant timeframes; considering Resolution BT 42/2008 allowing the CEN/TCs, for well identified and justified reasons, to claim one tolerance of 9 months, applicable to the target dates for submission of a draft to CCMC (or ISO/CS in case of Vienna - CEN Lead) for the relevant procedure(s) (i.e. CEN Enquiry and/or Formal Vote, UAP, TCA); considering that for item Automotive fuels - Sulfur content in liquefied petroleum gas - Determination by ultraviolet fluorescence (UVF), it proves impossible to Dispatch ENQ draft to CMC by ; claims a tolerance of 9 months (i.e. a postponement of 9 months of the deadlines for all the stages not yet reached) for the following reasons:

4 Page 4 The planning and execution of the interlaboratory study was delayed because of safety issues with distributing the samples. The ILS had to be reformatted and planned which resulted in additional costs to compensate travel of lab technicians. Funding needed to be gathered. The ILS was finalised some weeks ago (just before the deadline), but the statistical analysis presented some questions that needed to be discussed by our statistical ing group. The questions have not yet been answered so a precision statement is not yet available. That can be finalised within a couple of months. confirms that CEN/TC 19 will Dispatch ENQ draft to CMC (or ISO/CS in case of Vienna - CEN Lead) by at the latest. The decision was taken by simple majority with 15 positive vote(s), 0 negative vote(s) and 18 abstention(s). 3 CEN/TC 47 Decision CEN/TC 47 02/2017 taken on Subject: Activation of preliminary Work Item CEN/TC 47 Atomizing oil burners and their components - Function - Safety - Testing having considered the proposal for the activation of item currently registered at preliminary stage as documented in CEN/TC 47 N 707 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN :2000 EN :2000 CEN/TC 47/WG 4 - Oil supply systems 4. Title Components for supply systems for consuming units with liquid fuels 5. Scope This European Standard specifies the safety and performance

5 Page 5 6. Environmental? 9. The project is requirements and tests methods for the components for supply systems. Their intended use is the supply with liquid fuel for one or more consuming units from one or more tanks. This European Standard applies to pressurised, negative pressurised, unpressurised, underground, above ground, inside and/or outside systems to supply liquid fuels. The components for supply systems covered by this standard are piping kits/systems and their components. t covered by this standard are items belonging to the consuming unit (e. g.: heating/cooling appliances in buildings) and items used for the mounting and support of components. t covered by this standard are items with the intended use of gas for building heating/cooling systems and any items of heating nets. t covered are items used for drainage (including highways) and disposal of other liquids and gaseous waste, supply of gases, pressure and vacuum systems, communications, sanitary and cleaning fixtures and storage fixtures. Discharges to soil Heat Use of energy Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) Yes M/131 Yes Directive reference For citation in Official journal 305/2011 Yes 2014/32/EU Yes 2006/42/EC Yes ASI BSI SNV UNI

6 Page The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 11 Number of negative votes: 0 Number of abstentions: 10 4 CEN/TC 69 Decision CEN/TC /2017 taken on Subject: Reference to other normative documents CEN/TC 69 - Industrial valves considering the CEN/CENELEC Internal Regulations - Part 2 and Part 3, allowing in exceptional cases, to include normative references to documents other than those developed by CEN, CENELEC, ETSI, ISO and IEC; considering the CEN policy related to the subject; confirming that all following criteria are affirmatively fulfilled: o o o o no suitable CEN, CENELEC, ETSI, ISO or IEC documents are available and that there is a necessity to refer to a document other than those developed by CEN, CENELEC, ETSI, ISO and IEC; it is impractical to include the relevant text in full; the need for making reference to a document other than those developed by CEN, CENELEC, ETSI, ISO and IEC has been fully justified; the referenced document: has wide acceptance; approves the normative reference to: is not in contradiction with the European legislation nor creates regulatory problems when the EN is implemented by CEN/CENELEC members; has been prepared in accordance with the principles set in the ISO/IEC Guide 59 - Code of Practice for Standardization - (with the definitions of EN 45020) and in the ISO/IEC Directives; has clearance in respect of possible IPR (Intellectual Property Rights) issues as prescribed in CEN/CENELEC Guide 8; is not a draft, but is an adopted document with an identified and dated issue; is publicly available in official CEN/CENELEC languages, at least in English. ASME B16.25 Buttwelding Ends issued by ASME on

7 Page 7 In the document corresponding to WI FprEN Industrial valves - Butt welding ends for steel valves The decision was taken by unanimity. 5 CEN/TC 104 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Concrete and related products having considered the proposal for a new item as documented in CEN/TC 104 N having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable TR 2. This item corresponds to 3. Document A new TR CEN/TC 104/SC 1 - Concrete - Specification, performance, production and conformity 4. Title Carbonation and CO2-uptake in concrete 5. Scope The purpose and scope of this CEN/TR is to give background information and to deepen and explain the Annex BB on CO2-uptake by carbonation - Requirements and guidance on calculation, presented in the standard EN Product Category Rules for concrete and concrete elements. This TR is also providing typical CO2 uptake for different structures. It thereby makes it possible to present EPD:s for the whole life cycle for one m3 of concrete, without detailed knowledge of the structure to be built. In most cases only the concrete quality and if the concrete will be used for civil engineering or house building purpose is known, which is un-sufficient for specific calculation of CO2-uptake according

8 Page 8 to clause BB3 of the Annex BB in EN Environmental? 9. The project is Emissions to air Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Vote on TS/TR by correspondence AFNOR SNV NBN NEN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 17 Number of negative votes: 0 Number of abstentions: 0 6 CEN/TC 107 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs

9 confirming that the resources to complete the below are available DDD Page 9 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 253:2009+A2:2015 CEN/TC 107/WG 2 - Basic consideration 4. Title District heating pipes - Preinsulated bonded pipe systems for directly buried hot water nets - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard specifies requirements and test methods for straight lengths of prefabricated thermally insulated pipe-in-pipe assemblies for directly buried hot water nets, comprising a steel service pipe from DN 15 to DN 1200, rigid polyurethane foam insulation and an outer casing of polyethylene. The pipe assembly may also include the following additional elements: measuring wires, spacers and diffusion barriers. This standard applies only to insulated pipe assemblies, for continuous operation with hot water at various temperatures up to 120 C and occasionally with a peak temperature up to 140 C. The estimation of expected thermal life with continuous operation at various temperatures is outlined in Annex B. 6. Environmental? 9. The project is Heat Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV)

10 Page 10 ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 448:2015 CEN/TC 107/WG 5 - Fittings and valves 4. Title District heating pipes - Preinsulated bonded pipe systems for directly buried hot water nets - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard specifies requirements and test methods for fittings of prefabricated thermally insulated pipe-in-pipe assemblies comprising a steel service fitting from DN 20 to DN 1200, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water nets with preinsulated pipe assemblies in accordance with EN 253. This European Standard covers the following fittings: bend, tee, reducer, single use compensator and anchor.

11 Page 11 This European Standard applies only to factory made prefabricated fitting assemblies and single use compensators for continuous operation with hot water at various temperatures in accordance with EN 253. This European Standard applies to fitting assemblies with a minimum design pressure of 16 bar (overpressure) complying with EN This European Standard does not include calculation rules for loads and stresses. The design and installation rules, for the system, are given in EN Environmental? 9. The project is Heat Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) ASI BSI DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449

12 Page 12 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 488:2015 CEN/TC 107/WG 5 - Fittings and valves 4. Title District heating pipes - Preinsulated bonded pipe systems for directly buried hot water nets - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard specifies requirements and test methods for valves of prefabricated thermally insulated valve assemblies comprising a steel valve, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water nets with pre-insulated pipe assemblies in accordance with EN 253. This European Standard applies only to factory made prefabricated insulated valve assemblies for continuous operation with hot water at various temperatures in accordance with EN 253:2009+A1:2013, Clause 1 and the valve assemblies with a maximum operation pressure of 25 bar. For higher pressures, additional demands apply. NOTE For this application, the following valve types are commonly used: ball valves, gate valves, and butterfly valves. This European Standard does not include calculation rules for loads and stresses. These depend on the configuration of the system as it is installed. The design and installation rules are given in EN Environmental? Heat Bring in expertise to the WG or expected CEN lead 9. The project is document from another organization

13 Page Track Enquiry + Formal Vote (ENQ+FV) ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 489:2009 CEN/TC 107/WG 4 - Joints 4. Title District heating pipes - Preinsulated bonded pipe systems for directly

14 Page 14 buried hot water nets - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard specifies requirements for joints made under field conditions between adjacent preinsulated pipes and/or fittings in district heating nets. The specified general requirements are also valid for field-made T branches, bends, reducers, caps, etc. This European Standard covers jointing of steel service pipes by means of fusion welding, the connecting of casing ends with joint casings and the thermal insulation with poured rigid PUR foam or prefabricated PUR-foam insulation. This European Standard specifies methods for type tests of complete joints and PUR-foam for joints under laboratory conditions. The requirements of this European Standard can also be applied to casing pipe weldings/connections of on site made fittings. The requirements of this European Standard aim to obtain a technical life of the joints of at least 30 years. 6. Environmental? 9. The project is Heat Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1

15 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item DDD Page 15 CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 14419:2009 CEN/TC 107/WG 11 - Surveillance facilities 4. Title District heating pipes - Preinsulated bonded pipe systems for directly buried hot water nets - Surveillance systems 5. Scope This European Standard specifies basic functional requirements for surveillance systems for district heating pipe systems, specific requirements for measuring elements and their installation within preinsulated bonded pipes, valves and fittings, and the field assembly of these measuring elements in pipe joints. This standard specifies requirements for the manufacture of measuring elements, for the manufacture of preinsulated bonded pipe elements with measuring elements and for the assembly of the measuring elements in the field. All requirements and recommendations described in this standard are based on the experience gained with existing surveillance systems and their principal function, cf. Annex A. The specific requirements given are only valid for electrical wire based surveillance systems forming an integral part of the pipes, valves, fittings and joints. 6. Environmental Heat Bring in expertise to the WG

16 Page 16? 9. The project is or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item The revision of an EN

17 Page 17 corresponds to EN : Document CEN/TC 107/WG 2 - Basic consideration 4. Title District heating pipes - Preinsulated bonded twin pipe systems for directly buried hot water nets - Part 1: Twin pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard for District Heating Twin Pipes, specifies requirements and test methods for straight lengths of prefabricated thermally insulated pipe-in-pipe assemblies for directly buried hot water nets, comprising two steel service pipes from DN 15 to DN 250, rigid polyurethane foam insulation and one cylindrical outer casing of polyethylene. The pipe assembly may also include the following additional elements: Measuring wires, spacers and diffusion barriers. This standard applies only to insulated twin pipe assemblies, for continuous operation with hot water at various temperatures up to 120 C and occasionally with a peak temperature up to 140 C. The estimation of expected thermal life with continuous operation at various temperatures is outlined in Annex B of EN 253: Environmental? 9. The project is Heat Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33

18 Page 18 Number of negative votes: 0 Number of abstentions: 1 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Prefabricated district heating and district cooling pipe system having considered the proposal for a new item as documented in CEN/TC 107 N 449 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN :2015 CEN/TC 107/WG 5 - Fittings and valves 4. Title District heating pipes - Preinsulated bonded twin pipe systems for directly buried hot water nets - Part 2: Fitting and valve assembly of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene 5. Scope This European Standard specifies requirements and test methods for fittings of prefabricated thermally insulated twin pipe assemblies comprising steel service fittings and/or valves from DN 15 to DN 250, rigid polyurethane foam insulation and an outer casing of polyethylene for use in directly buried hot water nets with preinsulated twin pipe assemblies in accordance with EN :2009. This European Standard covers the following: - fitting assemblies, such as T-pieces, reducers and anchors; - valve assemblies. This European Standard applies only to insulated fitting assemblies for continuous operation with hot water at various temperatures in accordance with the scope EN :2009. This European Standard applies to fitting and valve assemblies with a

19 Page 19 minimum design pressure of 16 bar (overpressure) complying with EN Guidelines for quality inspection and testing of fitting assemblies are given in EN 448:2015, Annex A and EN :2009, Annex A. Guidelines for quality inspection and testing of valve assemblies are given in EN 488:2015, Annex A and EN :2009, Annex A. Procedures for PE-welding are given in EN 448:2015, Annex B. NOTE This European Standard does not include rules for calculation of loads and stresses. 6. Environmental? 9. The project is Heat Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) ASI SIS DS PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 33 Number of negative votes: 0 Number of abstentions: 1

20 7 CEN/TC 124 DDD Page 20 Decision 397 (PARIS N 1) taken by CEN/TC 124 on Subject: CEN/TC Appointment of Chairperson The CEN/TC 124 Timber Structures, considering the CEN/CENELEC Internal Regulations - Part 2, subclause 3.2.2, which lays down the rules for nomination, appointment and responsibilities of Chairpersons; noting the nomination by the Technical Committee Secretariat; noting the commitment of the applicant to the responsibilities and duties of a Technical Committee Chairperson as given in the CEN BOSS; decides to re-appoint Mr. Frédéric ROUGER, as Chairman of CEN/TC 124 for a period of 3 years starting on , noting that Mr. Frédéric ROUGER is Chairperson of the Technical Committee since The decision was taken by unanimity. 8 CEN/TC 153 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item CEN/TC Machinery intended for use with foodstuffs and feed having considered the proposal for a new item as documented in CEN/TC 153 N having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item An amendment to an EN

21 Page 21 corresponds to EN 12331: Document CEN/TC 153/WG 2 - Meat processing machinery 4. Title Food processing machinery - Mincing machines - Safety and hygiene requirements 5. Scope 1.1 This European Standard specifies requirements for the design and manufacture of mincing machines (see Figures 1a and 1b) used in a stationary position. The machines covered by this European Standard are used for size reduction of fresh or frozen meat, meat products and fish (hereinafter referred to as product) by cutting in a set of cutting tools. Mincing machines for domestic uses are not included in this European Standard. Filling mincers are covered by EN Food processing machinery Filling machines and auxiliary machines Safety and hygiene requirements. This European Standard applies only to machines that are manufactured after the date of issue of this European Standard. Mincing machines in connection with using a hold-to-run foot switch are not covered by this European Standard. This European Standard covers: - mincing machines used in shops and preparation rooms; - mincing machines used in kitchens where sausages are prepared; - mincing machines used industrially; - accessories. The extent to which hazards are covered, is indicated in this European Standard. For other hazards which are not covered by this European Standard, machinery should comply with EN ISO 12100:2010 where applicable. This European Standard is not dealing with specific requirements for the control of mincing machines with foot switch. 1.2 This European Standard covers the following types: - mincing machine with feed tray, feed intake and pusher, diameter 52 mm on feed intake (see Figure 3); - mincing machine with feed tray, feed intake, restrictor plate and pusher, diameter > 52 mm on feed intake (see Figure 4); - mincing machine with feed intake hopper and cover, screw conveyor, with 1) or without mixing screw in feed intake hopper (see Figure 5); - mincing machine with feed intake hopper, with or without cover, screw conveyor, with ) or without mixing screw in the feed intake hopper, with loading device (continuously or discontinuously). Mincing machines comprise a machine base, a worm casing with a worm, a feed tray (with feed intake) or a feed intake hopper, a screw conveyor (and sometimes an additional mixing screw in the feed intake hopper), a set of cutting tools, a lock nut, a loading device, a drive motor and depending on machine type electrical, hydraulic and pneumatic components. They will also have various safeguarding devices as examples in Clause 5. Mincing machines may be equipped e.g. with

22 Page Environmental? 9. The project is - an extraction claw, - an ejector or extractor, - a protective hood over the discharge outlet, - a cover over the inlet opening of the feed intake hopper, - a transport carriage for the lock nut, the set of cutting tools, the worm and the screw conveyor, - a lifting device for the lock nut, the set of cutting tools, the worm and the screw conveyor, - a loading device. 1.3 Intended use The product is fed manually or by means of the loading device into the mincing machine. The product is fed to the worm either by means of a pusher or a screw conveyor and size reduced in the set of cutting tools. It is not intended that mincing machines are cleaned with pressurized water. However, it is to be foreseen that it is difficult to guarantee that this method will never be used in practice. In order to deal with this eventuality, the requirements of should apply. This European Standard specifies all significant hazards, hazardous situations and events relevant to mincing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the hazards which can arise during commissioning, operation, cleaning, use, maintenance and decommissioning of the machine. ne of the above: The item deals with a particular Clause in the standard that does not affect issues, but only covers very specific safety. Other: See explanation above. or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) Yes M/396 Yes Directive reference For citation in Official journal 2006/42/EC Yes AFNOR SIS BSI

23 Page 23 DS UNI 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 13 Number of negative votes: 0 Number of abstentions: 9 9 CEN/TC 162 Decision CEN/TC /2017 taken on Subject: Activation of preliminary Work Item pren 407 rev CEN/TC Protective clothing including hand and arm protection and lifejackets having considered the proposal for the activation of item currently registered at preliminary stage as documented in CEN/TC 162 N 3724 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 407:2004 CEN/TC 162/WG 8 - Protective gloves 4. Title Protective gloves against thermal risks (Heat and/or fire) 5. Scope This standard specifies test methods, general requirements, levels of thermal performance and the marking for protective gloves against heat and/or fire. It is to be used for all gloves which protect the hands against heat and/or flames in one or more of the following forms: fire, contact heat, convective heat, radiant heat, small splashes or large quantities of molten metal. Product tests may only give performance levels and not protection levels.

24 Page Environmental? 9. The project is ne of the above: Standard deals with PPE. Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) Yes M/031 Yes Directive reference For citation in Official journal 2016/425 Yes 89/686/EEC Yes AFNOR SFS BSI SNV NBN NEN IPQ 14. The decision was taken by Weighted vote and simple majority Percentage of positive weighted votes (min. 71% before , min. 65% from ):99 Number of positive votes: 17 Number of negative votes: 1 Number of abstentions: 6 Decision CEN/TC /2017 taken on Subject: Deletion of a Work Item neither mandated nor covered by an Order Voucher CEN/TC Protective clothing including hand and arm protection and lifejackets having received and agreed upon the reasons why harmonization is no longer needed; considering that the item(s) are neither mandated nor covered by an Order Voucher;

25 Page 25 noting the consequences of release of standstill; decides to delete the following item(s): WI pren rev - Visibility accessories for non-professional use - Test methods and requirements and decides to release the standstill on these item(s). The decision was taken by simple majority with 16 positive vote(s), 1 negative vote(s) and 6 abstention(s). Decision CEN/TC 162 C459/2017 taken on Subject: Adoption of a New Work Item CEN/TC Protective clothing including hand and arm protection and lifejackets having considered the proposal for a new item as documented in CEN/TC 162 N 3725 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The revision of an EN EN 1150:1999 CEN/TC 162/WG 7 - Visibility clothing and accessories 4. Title Protective clothing - Visibility clothing for non-professional use - Test methods and requirements 5. Scope This Standard specifies the optical performance requirements for high-visibilty clothing to be worn by adults and by juveniles, and designed for non-professional use. High-visibility clothing for nonprofessional use is intended to signal the user's presence visually in any daylight condition and, when illuminated by vehicle headlights or search lights in the dark as well as lit up in urban roads. This standard is not applicable to accessories to be carried by persons or

26 Page 26 attached to garments. 6. Environmental? 9. The project is ne of the above: Standard deals with PPE Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) Yes M/BC/CEN/90/2 Yes Directive reference For citation in Official journal 89/686/EEC Yes AFNOR SFS NBN UNI NEN IPQ 14. The decision was taken by Weighted vote and simple majority Percentage of positive weighted votes (min. 71% before , min. 65% from ):94 Number of positive votes: 16 Number of negative votes: 1 Number of abstentions: 6 10 CEN/TC 205 Decision CEN/TC 205 8/2017 taken on Subject: CEN/TC Decision to skip the Formal Vote CEN/TC 205 n-active medical devices considering the results of the Enquiry ballot;

27 Page 27 considering the table of decisions and the formal written proposals as distributed after the comments decision meeting; considering the CEN/CENELEC Internal Regulations - Part 2, clause ; considering Decisions BT 34/2002, BT 42/2003 and related document BT N 6962 concerning timeframes for the development of ENs; considering Decision BT 35/2014 to associate a vote to the CEN Enquiry and to allow Technical Bodies to decide to skip the Formal Vote; considering Decision 49/2014 to allow Technical Bodies to decide to skip the Formal Vote through a TC decision based on simple majority only; decides to skip the Formal Vote and proceed with the publication of WI EN 455-3:2015/prA1 - Medical gloves for single use - Part 3: Requirements and testing for biological evaluation (In this case the TC must not finalize the publication, this will be done by CCMC. Instead the TC must notify CCMC of its intention to skip Formal Vote by posting only an electronic transmission notice onto etrans.) The decision was taken by unanimity. 11 CEN/TC 207 Decision 1 (660/2017) taken by CEN/TC 207 on Subject: CEN/TC Decision to skip the Formal Vote on pren CEN/TC Furniture considering the results of the Enquiry ballot; considering the table of decisions and the formal written proposals as distributed after the comments decision meeting; considering the CEN/CENELEC Internal Regulations - Part 2, clause ; considering Decisions BT 34/2002, BT 42/2003 and related document BT N 6962 concerning timeframes for the development of ENs; considering Decision BT 35/2014 to associate a vote to the CEN Enquiry and to allow Technical Bodies to decide to skip the Formal Vote; considering Decision 49/2014 to allow Technical Bodies to decide to skip the Formal Vote through a TC decision based on simple majority only; decides to skip the Formal Vote and proceed with the publication of WI EN 16121:2013/prA1 - n-domestic storage furniture - Requirements for safety, strength, durability and stability (In this case the TC must not finalize the publication, this will be done by CCMC. Instead the TC must notify CCMC of its intention to skip Formal Vote by posting only an electronic transmission notice onto etrans.)

28 Page 28 The decision was taken by unanimity. 12 CEN/TC 218 Decision M04/2017 taken by CEN/TC 218 on Subject: 3 year time-frame for the development of ENs, TRs and TSs 9 month Tolerance Request CEN/TC 218 Rubber and plastics hoses and hose assemblies considering Resolution BT 34/2002 by which BT decided that any item to result in an EN, registered after , shall normally result in an EN after 3 years and set maximum times between well identified stages, as well as Resolution BT 42/2003 deciding on variant timeframes; considering Resolution BT 42/2008 allowing the CEN/TCs, for well identified and justified reasons, to claim one tolerance of 9 months, applicable to the target dates for submission of a draft to CCMC (or ISO/CS in case of Vienna CEN Lead) for the relevant procedure(s) (i.e. CEN Enquiry and/or Formal Vote, UAP, TCA); considering that for item pren Thermoplastic multi-layer (nonvulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification, it proves impossible to provide a draft for Formal Vote by ; claims a tolerance of 9 months (i.e. a postponement of 9 months of the deadlines for all the stages not yet reached) for the following reasons: Development of text for the test procedure of resistance to liquid fuels (LNG, LPG) conveyed; confirms that a draft will be sent to CCMC (or ISO/CS in case of Vienna CEN Lead) for submission to the foreseen procedure by at the latest. The decision was taken by 7 positive votes, 0 negative votes and 0 abstentions. 13 CEN/TC 261 Decision CEN/TC 261 N013/2017 taken on Subject: Adoption of a New Work Item CEN/TC 261 Packaging having considered the proposal for a new item as documented in CEN/TC 261 N 539 having considered the Guidance - Adoption of a new item in a CEN

29 Page 29 confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable TR 2. This item corresponds to 3. Document The revision of a CEN/TR CEN/TR :2004 CEN/TC 261/SC 4/WG 8 - Heavy metals and other dangerous substances 4. Title Packaging - Requirements for measuring and verifying the four heavy metals and other dangerous substances present in packaging, and their release into the environment - Part 2: Requirements for measuring and verifying dangerous substances present in packaging, and their release into the environment 5. Scope This document specifies the methodology and procedure for determining the presence and minimisation of other dangerous substances in relation with Annex II Para 1 Indent 3 of Directive 94/62/EC. This document is intended to be of practical use, and to enable efficient application of the Directive 94/62/EC, even for small and medium sized companies in the packaging industry, providing them with a methodology for assessing compliance with the Directive. This document cannot by itself provide presumption of conformity. The procedure for applying this document is contained in EN Environmental? 9. The project is Other: Refer to EN to EN (Harmonised standards) Other: t relevant or expected CEN lead document from another organization 10. Track Vote on TS/TR by correspondence Yes M/200 Yes Directive reference For citation in Official journal

30 Page 30 94/62/EC AFNOR SIS BSI NBN UNI NEN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 13 Number of negative votes: 0 Number of abstentions: 8 14 CEN/TC 264 Decision CEN/TC /2017 taken on Subject: Activation of preliminary Work Item pren CEN/TC Air quality having considered the proposal for the activation of item currently registered at preliminary stage as documented in CEN/TC 264 N 2601 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document The conversion of a CEN/TS into an EN CEN/TS 16868:2015 CEN/TC 264/WG 39 - Sampling and analysis of airborne pollen grains and fungal spores 4. Title Ambient air - Sampling and analysis of airborne pollen grains and fungal spores for allergy nets - Volumetric Hirst method

31 Page Scope This document specifies the procedure to sample continuously and analyse the concentration of airborne pollen grains and fungal spores in ambient air using the volumetric Hirst type sampler. This document describes both the sampling and the analysis procedures for the purpose of allergy nets. Other specifications may be required. A synergy exists between pollen and fungal spores' exposition and air pollution which requests some specific and complementary information in order to decrease the risk of health impact. 6. Environmental? 9. The project is Other: neuroth@vdi.de/ : Ambient air quality Bring in expertise to the WG or expected CEN lead document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) AFNOR BSI UNE UNI 14. The decision was taken by Weighted vote and simple majority Percentage of positive weighted votes (min. 71% before , min. 65% from ):100 Number of positive votes: 10 Number of negative votes: 0 Number of abstentions: 14

32 15 CEN/TC 307 Decision CEN/TC /2017 taken on Subject: Adoption of a New Work Item DDD Page 32 CEN/TC 307 Oilseeds, vegetable and animal fats and oils and their by-products - Methods of sampling and analysis having considered the proposal for a new item as documented in CEN/TC 307 N 519 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable EN 2. This item corresponds to 3. Document A new project CEN/TC Oilseeds, vegetable and animal fats and oils and their by-products - Methods of sampling and analysis 4. Title Animal and vegetable fats and oils - Determination of fatty-acid-bound chloropropanediols (MCPDs) and glycidol by GC/MS - Part 2: Method using slow alkaline transesterification and measurement for 2- MCPD, 3-MCPD and glycidol 5. Scope This part of ISO describes a procedure for the parallel determination of glycidol together with 2-MCPD and 3-MCPD present in bound or free form in oils and fats. The method is based on alkalinecatalyzed ester cleavage, transformation of the released glycidol into monobromopropanediol (MBPD) and derived free diols (MCPD and MBPD) with phenylboronic acid (PBA). Though free MCPD and glycidol are supposed to be present in fats and oils in low to negligible quantities only, significant content would increase proportionately the determination of bound analytes. This method is applicable to solid and liquid fats and oils. This part of ISO can also apply to animal fats and used frying oils and fats, but a validation study must be undertaken before the analysis of these matrices. Milk and milk products (or fat coming from milk and milk products) are excluded from the scope of this international standard.

33 Page Environmental? 9. The project is Use of materials Waste Other: Taking into account by ISO/TC 34/SC 11 having the lead on the development of this project. Yes - Parallel ISO lead ISO project reference: ISO/NP ISO project ID: ISO TC: ISO/TC 34 document from another organization 10. Track Enquiry + Formal Vote (ENQ+FV) AFNOR UNI NEN IPQ 14. The decision was taken by Weighted vote and simple majority Percentage of positive weighted votes (min. 71% before , min. 65% from ):100 Number of positive votes: 11 Number of negative votes: 0 Number of abstentions: 8 16 CEN/TC 440 Decision CEN/TC /2016 taken on Subject: Adoption of a New Work Item CEN/TC 440 Electronic Public Procurement having considered the proposal for a new item as documented in CEN/TC 440 N 86 having considered the Guidance - Adoption of a new item in a CEN

34 confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available DDD Page Deliverable TR 2. This item corresponds to 3. Document A new TR CEN/TC 440/WG 3 - e-tification 4. Title CEN/prTR Electronic public procurement - Business interoperability interfaces (BII), e-tification - Part 101: Overview 5. Scope This document provides an overview of e-tification standards in the set Business Interoperability Interfaces (BII) for public procurement. BII e-tification covers the processes of publishing notices, disseminating notices and searching the notices on portals. tices include the prior information notice, the contract notice and the contract award notice. BII focus on exchange of information between business partners. This brings in scope all electronic communication between a contracting authorities, notices portals, e.g. Tenders Electronic Daily (TED) and aggregators/service providers. Back-office information processing, like creating of the notice, is out of scope. To ensure interoperability each electronic communication will be described as follows: - A procurement procedure guideline identifies the position of the transactions in a procedure; - A choreography describes the sequence of transactions; - A transaction describes all information elements exchanged between business partners; - A syntax implementation guideline (SIG) provides the syntax bindings needed to implement the transaction. 6. Environmental? 9. The project is ne of the above: There is no direct impact on Other: There is no direct impact on or expected CEN lead document from another organization

35 Page Track Vote on TS/TR by correspondence SN DS UNI NEN PKN 14. The decision was taken by Simple majority (min. 55% as from ) Number of positive votes: 12 Number of negative votes: 0 Number of abstentions: 7 Decision CEN/TC /2016 taken on Subject: Adoption of a New Work Item CEN/TC 440 Electronic Public Procurement having considered the proposal for a new item as documented in CEN/TC 440 N 92 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable TR 2. This item corresponds to 3. Document A new TR CEN/TC 440/WG 4 - e-tendering 4. Title CEN/prTR "Electronic public

36 Page 36 procurement - Business interoperability interfaces (BII), e-tendering - Part 101: Overview 5. Scope This document provides an overview of etendering standards in the set Business Interoperability Interfaces (BII) for public procurement. BII etendering covers the tendering part of the e-procurement chain, starting from subscribing interest in a business opportunity till concluding the contract. BII focus on exchange of information between business partners. This brings in scope all electronic communication between a contracting authority and an economic operator. Back-office information processing, like the evaluation of tenders, is out of scope. 6. Environmental? 9. The project is To ensure interoperability each electronic communication will be described as follows: - A procurement procedure guideline identifies the position of the transactions in a procedure; - A choreography describes the sequence of transactions; - A transaction describes all information elements exchanged between business partners; - A syntax implementation guideline (SIG) provides the syntax bindings needed to implement the transaction. ne of the above: There is no direct impact on Other: There is no direct impact on or expected CEN lead document from another organization 10. Track Vote on TS/TR by correspondence SN DS UNI NEN IPQ PKN 14. The decision Simple majority (min. 55% as from )

37 Page 37 was taken by Number of positive votes: 12 Number of negative votes: 0 Number of abstentions: 7 Decision CEN/TC /2016 taken on Subject: Adoption of a New Work Item CEN/TC 440 Electronic Public Procurement having considered the proposal for a new item as documented in CEN/TC 440 N 93 having considered the Guidance - Adoption of a new item in a CEN confirming that the new item corresponds to real market needs confirming that the resources to complete the below are available 1. Deliverable TR 2. This item corresponds to 3. Document A new TR CEN/TC 440/WG 5 - e-catalogue 4. Title CEN/prTR Electronic public procurement - Business interoperability interfaces (BII), e-catalogue - Part 101: Overview 5. Scope The CEN/TC 440/WG5 has developed a set of deliverables to support interoperability in the pre- and post-award areas of public procurement. In particular, the deliverables cover the exchange of electronic product catalogues and related documents between contracting bodies and economic operators respectively buyers and sellers. An electronic product catalogue contains specifications of products (goods and services) with their pricing. A catalogue is used to serve as a basis for ordering and all other following postaward processes. To ensure interoperability each electronic communication will be described as follows: - A choreography describes the sequence of transactions; - A transaction describes all information elements exchanged between business partners; - A syntax implementation guideline (SIG) provides the syntax bindings needed to implement the transaction.