CHART PERUVIAN TECHNICAL STANDARDS

Transcription

1 CHART PERUVIAN TECHNICAL STANDARDS

2 Peruvian Technical Standards Elaborated by the Normative Technical Committee Rational Use of Energy and the Energy Efficiency - (December 2007) Electric Motors Industrial Boilers Refrigeration 01 NTP IEC : NTP IEC /A2 Addenda 2 03 NTP NTP NTP NTP ISO 7371: NTP ISO 8561: NTP Rotation Electrical Motors. Test Methods Rotation Electrical Motors. Test Methods (Part 2) Energy Efficiency squirrel cage motors. Limits and Labeling. Industrial Boilers. Procedure for energy efficiency determination. Industrial Boilers. Minimum Levels of thermal efficiency Refrigerators with or without food compartments with low temperature. Characteristic and test methods. Appliances for storage of frozen food and food freezers. Characteristics and test methods Energy Efficiency in Refrigerating appliances, Refrigerators Freezers and for Domestic Use Establishes methods to determine the efficiency from the tests, and also specifies the methods to obtain the losses of a certain nature when these are required for other purposes. Introduces the following modifications to the Standard NTPIEC / 2001, according to the corresponding standard IEC 34-2/A2:199. Establishes the minimum efficiency values and the labeling specification which should be complied with by electric motors to which this Standard refers Establishes the test method to be applied to verify the thermal efficiency of the package type boilers with smoke pipes and water pipes without heat recovery equipment at the moment of their reception. All boilers which are within the field of application of this Standard should be tested. Establishes the thermal efficiency standards which should be complied with by new industrial boilers without heat recovery equipment. Establishes essential characteristics of the domestic refrigerators, with or without storage or low temperature compartments which are completely assembled in factory, and proposes test methods for checking these characteristics. Specifies the essential characteristics for domestic appliances for storage of frozen food and freezers for food cooled by internal forced air circulation and for refrigerators-freezers with or without frozen food storage compartments or hold, cooled by internal forced air circulation, which are completely assembled in factory and dictates the test methods for checking these characteristics. Establish the energy consumption of reference CER and the ranks of energy consumption which will permit to classify food refrigerators, refrigerators-freezers and freezers according to their energy behavior, specifying the contents of the label of energy consumption for all the types of domestic refrigeration appliances operated with hermetic motor compressor when they are tested and classified according to what is established in Chapter 15 of standard NTP-ISO 8561 and standard NTP ISO Oct Oct Aug Dec Aug Jun Apr Mar

3 Solar Systems Lighting 09 NTP NTP NTP NTP NTP NTP NTP NTP IEC NTP IEC Solar collectors. Test methods to determine efficiency Photovoltaic Systems of up to 500 Wp. Technical specifications and method for energy qualification. Solar Energy Water Heating Systems. Bases for their efficient dimensioning. Solar Energy Water Heating Systems. Procedure for their efficient installation. Solar Energy Water Heating. Definition and annual forecast for their yield with outdoors tests. Compact Fluorescent Lamps Definitions, requirements and labeling. Labeling of energy efficiency for domestic use lamps. Ballasts for tubular Requirement for functioning Control devices for lamps. Part 1: General requirement and safety features. Establishes the test methods to determine the thermal behavior of solar energy collectors which uses one single phase and do not have significant energy interior feed. Establishes a set of technical requirements for the components of the photovoltaic system, such s the photovoltaic modules, the batteries, load controllers, fluorescent lamps and the integrated photovoltaic system. Likewise, is established a procedure to obtain the energy capacity of a photovoltaic system. Establishes the main principles for designing a solar heating system for drainage waters, with collectors with plane plates without inside energy storage and storage deposit Establishes the procedures and precise techniques to install a Water Heating System with Solar Energy, considering the conditions and general characteristics of the destination physical space. Establishes the test procedures which will permit to define the yield of the Solar Energy Water Heating (Sistemas de Calentamiento de Agua con Energía Solar (SCAES)) under direct exposure to solar radiation (out of doors tests), without auxiliary reinforcement for heating, to forecast annual yield of the system for a period of twelve (12) hours of daily heating. Establishes the minimum energy efficiency specifications which Compact Fluorescent Lamps should have in Peru, so they can have official certification. Likewise, sets the technical parameters, both electronic and luminous, the values of which should be complied with by the Compact Fluorescent Lamps. Establishes the specifications which should be complied with by the design of the energy efficiency label for domestic use lamps. Also specifies the classes of energy efficiency that a lamp has. Specifies the requirements of the behavior of the ballasts excluding those of the resistance type for use with supplies of alternate current up to 1000 V, at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with preheated cathodes with or without starter or starting device with nominal power, dimensions and characteristics specified in standards IEC and This standard is applied to complete ballasts and its component parts such as resistors, transformers and condensers. Specified the general requirements and requisites for safety in control devices of lamps destined to be used with continuous current feed up to 250 V and/or with alternate current feed of up to V at 50 Hz or 60 Hz. Nov Feb Oct Feb Jun Oct Jan Dec Mar

4 Water Heaters NTP IEC NTP IEC NTP IEC NTP IEC NTP IEC NTP Control devices per lamps. Part 2-8: Particular requirements for ballasts in Control devices for lamp. Part 2-9. Particular requirements for discharge lamps ballasts (except fluorescent lamps). Auxiliary equipment for discharge lamps ballasts (excluding the tubular fluorescent lamps). Requirements for operation. Method for measuring total inlet power of the circuits of lamps ballasts. Devices for lamp control. Part 2-3. Particular requirements for electronic ballasts fed with alternate current for fluorescent lamps. Luminaries. Part Particular requirements. Luminaries for emergency. Electronic ballasts fed with alternate current for tubular Requirements for operation. Methods to measure efficiency of accumulation electric water heaters for domestic use Gas appliances, Normal gases for tests Terminology, Classification and Specifications. Specifies particular requisites for safety in ballasts other than those of the resistor type, to be used with alternate current up to V of frequency equal to 50 Hz or 60 Hz, associated to fluorescent lamps with or without preheated cathodes which operate with or without feeder or starter device and the nominal power of which, dimensions and characteristics are indicated in Standard IEC and in Standard IEC Specifies the particular safety requirements for ballasts of discharge lamps such as mercury vapor lamps at high pressure, sodium vapor lamps at low pressure, sodium vapor lamps at high pressure and halogen metallic lamps Specifies the requirements of operation of ballasts for discharge lamps such as mercury vapor at high pressure, sodium vapor lamps at low pressure, sodium vapor lamps at high pressure and halogen metallic lamps Gives the total inlet power measuring method of the ballast-lamps circuits when they operate with their associated fluorescent lamp(s). This standard is applied to electric ballast-lamp circuits including only the ballast and the lamp(s). Specifies the particular safety requirements applicable to electronic ballasts for the use with alternate current up to V at 50 Hz or 60 Hz with operation frequencies other than those of the feeding network, associated with the fluorescent lamps specified in Standard IEC and Standard IEC 60901,and to other fluorescent lamps which operate at high frequency. Specifies the requirements applicable to the luminaries for emergency lighting destined to be used with sources of electric light for emergency feeding voltages which will not overpass V. Specifies the requisites of operation for electronic ballasts fed with alternate current of up to V, at 50 Hz or 60 Hz, with working frequencies which are not those of the feeder frequency and used in association with tubular fluorescent lamps as indicated in Standards IEC and IEC 60901, and with other types of fluorescent lamps for the operation at high frequency. Establish and define the main characteristics for the operation of the electric accumulation water heaters which are of the user s interest and describe the standardized methods for measuring these characteristics. Establishes the test gases, the test pressures and the categories of the appliances, relative to the use of gaseous fuels of the first, second and third families. May Jul Aug Dec Jan Mar Nov Feb Jan

5 Peruvian Technical Standards in process of by (December 2007) Sub- Committee Refrigeration 01 Lighting 02 Lighting 03 Lighting 04 Lighting 05 Lighting 06 Item Standard Name Domestic Refrigeration Appliances, Appliances for frozen food storage and freezers. Characteristics and test methods. Date Submission to n Sept Starters to put on fluorescent lamps Lamp control devices. Part 2-1: Particular requisites for starters (except fluorescent lamp starters) Auxiliaries for lamps. Condensers for use in the tubular fluorescent lamps and other discharge lamps circuits. General and safety requirements Condensers to use in tubular fluorescent lamps and discharge lamps. Requirements of operation. Lamp control devices. Fluorescent lamps ballasts. Energy Codification System. Dec