1.6. Installation instructions for Bridge Navigation Watch Alarm System (BNWAS 3000)

Transcription

1 Technical Documentation BNWAS Installation instructions for Brid Navigation Watch Alarm System (BNWAS 000) WATCH ALARM MAIN UNIT REATER UNIT SELECTOR UNIT RESET UNIT Revisions Version Date Author Checked Remark.0 0/0/ JB TM Derived from draft 0. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

2 Technical Documentation BNWAS 000 Table of contents. General.... Cable requirements.... Connection of the various units.... Setting the address (REATER UNIT) Accumulator charging Pin assiments WATCH ALARM MAIN UNIT REATER UNIT..... SELECTOR UNIT..... RESET UNIT..... BOOSTER UNIT Current Accumulator Installation Audible sial nerator Reset sensor Location Compass safe distance Commissioning... Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

3 Technical Documentation BNWAS 000. General These installation instructions supplement the documentation of the BNWAS (system description, operating instructions, technical documentation...). For further information, see the relevant documentation. The currently applicable standards must be consulted prior to installation of the BNWAS and observed.. Cable requirements For safe operation of the entire system, the cables shown in the table are recommended. Connector Cable type Core diameter Cable diameter Power supply 00-0 Unshielded cable min. x. mm² V AC (JM) Power supply V DC Unshielded cable min. x. mm² (JM) Accumulator V Shielded cable x. mm² (JB) REATER UNIT Shielded twisted-pair cable x x 0.7 mm² (JR, JR) RESET UNIT (JQ) Shielded twisted-pair cable min. x x 0.7 mm² -0mm SERIAL OUT (JV) Shielded twisted-pair cable x 0.7 mm² SERIAL OUT (JV) Shielded standard serial cable SERIAL IN (JG) Shielded twisted-pair cable x 0.7 mm² SERIAL IN (JA) Shielded twisted-pair cable x 0.7 mm² RESET SENSOR Unshielded cable min. x 0.7 mm² (JE) Relay output (JK) Unshielded cable min. 9 x.0 mm² AUTO MODE ON/OFF; ext. sial nerator (JPI) Unshielded cable x 0.7 mm² Cable diameter depends on cable length and number of UNITS. Cable diameter depends on current and volta. Cable diameter depends on connected siren, current and volta. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

4 Technical Documentation BNWAS 000. Connection of the various units /0 - V mains-control Accu-control V - V RTC RS8 RS8 x out-control In ext. reset REATER UNIT SERIAL OUT / SERIAL IN RESET SENSOR RESET UNIT Power supply 00-0 V AC Power supply V DC Accumulator V JM JM JB WACHT ALARM MAIN UNIT BNWAS000 M U-E V - V Beeper DECKMA GMBH Status-LED Mikrocontro ller Mikrocontroller V - V Auto on/off Ext. Beeper V - V V - V V - V V - V RS8 RS8 JR JV JR JV JP JG JA JE JK JQ WATCH ALARM MAIN UNIT AUTO MODE ON/OFF; ext. Sial nerator WATCH ALARM MAIN UNIT SERIAL IN Power supply V DC REATER UNITS WATCH ALARM MAIN UNIT Relay output WATCH ALARM MAIN UNIT REATER UNIT BNWAS000 RPU-E DECKMA GMBH JR DECKMA GMBH JR JM JQ DECKMA GMBH RESET UNIT JQ BOOSTER UNIT BNW AS000 BU-E JR Beeper V - V JR JR Mikrocontroller RS8 JR SELECTOR UNIT BNWAS000 SU-E BNWAS000 RSU-E RESET UNITS JQ0 Power supply V DC JM Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

5 Technical Documentation BNWAS 000 Wiring diagram BNWAS 000 without SELECTOR UNIT SERIAL RS8-A RS8-B JV SERIAL OUT SERIAL TXD RXD 7 8 JV 9 SERIAL OUT PC, VDR, Gerneralalarm... V DC power supply rt sw gr/ V in JM Power supply V DC Netz bl gr/ N in L in JM Power supply 00-0 V AC Akku V V 7Ah V 7Ah ,A rt sw BP BM SC A SC B R JB Accumulator V General alarm, Sial nerator... K NO K CM K NC K NO K CM K NC K NO K CM K NC JK Relay output Time/date in, Reset, Emerncy Alarm Via RS or RS8 RXD TXD RS8-A RS8-B JG SERIAL IN Time/date in, Reset, Emerncy Alarm Via RS or RS8 RXD TXD RS8-A RS8-B JA SERIAL IN Überarbeitet MP / 0.0. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

6 Technical Documentation BNWAS 000 V in LED in RESET out optional JQ JQ0 MU RSU V out LED out RESET in V in LED in RESET out JQ MU RESET UNIT 0x max BOOSTER UNIT JM Power supply V DC V ext. JQ RESET UNIT V out LED out RESET in V in LED in RESET out JQ MU RESET UNIT x max RS8-A RS8-B V in ADR 0 ADR AS WAP 7 8 REATER UNIT WATCH ALARM MAIN UNIT JR JR REATER UNIT RS8-A RS8-B V out RS8-A RS8-B V in ADR 0 ADR AS WAP 7 8 REATER UNIT WATCH ALARM MAIN UNIT JPI AUTO MODE ON/OFF; ext. Sial nerator V out SIGNAL out AUTO in V PZ Sial RS8-A RS8-B V in ADR 0 ADR AS WAP 7 8 REATER UNIT WATCH ALARM MAIN UNIT RS8-A RS8-B V in ADR 0 ADR AS WAP 7 8 REATER UNIT WATCH ALARM MAIN UNIT JE RESET SENSOR SABOT in RESET in V out Sabota Reset Sensorik Reset Reset Sensorik WATCH ALARM MAIN UNIT Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

7 Technical Documentation BNWAS 000 Wiring diagram BNWAS 000 with SELECTOR UNIT SERIAL RS8-A RS8-B JV SERIAL OUT SERIAL TXD RXD 7 8 JV 9 SERIAL OUT PC, VDR, Gerneral alarm... V DC power supply rt sw gr/ V in JM Power supply V DC Netz bl gr/ N in L in JM Power supply 00-0 V AC Akku V V 7Ah V 7Ah ,A rt sw BP BM SC A SC B R JB Accumulator V General alarm, Sial nerator... K NO K CM K NC K NO K CM K NC K NO K CM K NC JK Relay output Time/date in, Reset, Emerncy Alarm Via RS or RS8 RXD TXD RS8-A RS8-B JG SERIAL IN Time/date in, Reset, Emerncy Alarm Via RS or RS8 RXD TXD RS8-A RS8-B JA SERIAL IN Überarbeitet MP / 0.0. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 7 of

8 Technical Documentation BNWAS 000 V in LED in RESET out optional JQ JQ0 MU RSU V out LED out RESET in V in LED in RESET out JQ MU RESET UNIT 0x max BOOSTER UNIT JM Power supply V DC V ext. JQ RESET UNIT V out LED out RESET in V in LED in RESET out JQ MU RESET UNIT x max optional RS8-A RS8-B V in ADR 0 ADR 7 AS WAP 8 REATER UNIT WATCH ALARM MAIN UNIT JR JR REATER UNIT RS8-A RS8-B V out RS8-A RS8-B V in JR WATCH ALARM MAIN UNIT JR RPU JR RPU RS8-A RS8-B V out RS8-A RS8-B V out RS8-A RS8-B V in ADR 0 ADR 7 AS WAP 8 REATER UNIT WATCH ALARM MAIN UNIT JPI AUTO MODE ON/OFF; ext. Sial nerator V out SIGNAL out AUTO in V PZ Sial V in optional power supply JM Power supply V DC JR RPU JR RPU RS8-A RS8-B V out RS8-A RS8-B V out RS8-A RS8-B V in ADR 0 ADR 7 AS WAP 8 REATER UNIT WATCH ALARM MAIN UNIT JE RESET SENSOR SABOT in RESET in V out Sabota Reset Sensorik Reset Reset Sensorik SELECTOR UNIT max. ciruits each with maximum Repeater Units RS8-A RS8-B V in ADR 0 ADR 7 AS WAP 8 REATER UNIT WATCH ALARM MAIN UNIT WATCH ALARM MAIN UNIT Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 8 of

9 Technical Documentation BNWAS 000. Setting the address (REATER UNIT) The REATER UNIT functions as a slave within a bus system from where it receives all system relevant data. Since up to four REATER UNITS can be connected to the BNWAS, each UNIT requires its own address on the bus. The address can be set by connecting Pins and/or 7 of connector JR to ground. Pin Pin 7 Address - - Gnd - - Gnd Gnd Gnd If the system is only configured for one REATER UNIT, only address must be used. If the system has been configured for two UNITS, address must be added for three UNITS, and for the maximum number (four),. If the address no lonr corresponds to the system configuration, an error is nerated.. Accumulator charging The accumulator is chard via current control. The current can be adjusted with a resistor connected between PINS and on the V accumulator connector (JB). Resistor 0-00 Ω 00 ma KΩ 0 ma.00 - KΩ 00 ma No resistor open 0 ma Current. Pin assiments.. WATCH ALARM MAIN UNIT Pin assiments Power supply V DC -pin Weidmüller RM.08 JM V in Power supply V DC in Shield Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 9 of

10 Technical Documentation BNWAS 000 Pin assiments Power supply 00-0 V AC -pin Phoenix RM.08 JM N in V AC L in Neutral Shield Pin assiments Accumulator V -pin Weidmüller RM.08 JB BP V BM SC A Charging current selection SC B Charging current selection Shield Charging current selection Resistor Charging current Suitable for accumulators 0R max. 00 ma > A/h k max. 0 ma >. A/h k max. 00 ma > A/h None max. 0 ma > 00 ma/h Pin assiments RESET UNIT -pin Weidmüller RM.08 JQ V out Power supply V out LED out LED ightness/on/off RESET in Reset Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 0 of

11 Technical Documentation BNWAS 000 Pin assiments REATER UNIT -pin Weidmüller RM. JR JR Shield RS8-A RS8-A connection to REATER UNIT RS8-B RS8-B connection to REATER UNIT V out Power supply V out Pin assiments AUTO MODE ON/OFF; -pin Phoenix RM.08 JPI External sial nerator V out Power supply V for sial nerator SIGNAL out External sial nerator NC Not connection AUTO in AUTO MODE ON/OFF Pin assiments SERIAL OUT -pin Weidmüller RM. JV RS8-A RS8-A event and alarm out RS8-B RS8-B event and alarm out Shield Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

12 Technical Documentation BNWAS 000 Pin assiments SERIAL OUT 9-pin Sub-D female connector JV TXD RS TxD service out RXD RS RxD service out Pin assiments SERIAL IN -pin Weidmüller RM. JG Shield RXD RS RxD serial reset/time and date in TXD RS TxD serial reset/time and date in RS8-A RS8-A serial reset/time and date in RS8-B RS8-B serial reset/time and date in Pin assiments SERIAL IN -pin Weidmüller RM. JA Shield RXD RS RxD serial reset/time and date in TXD RS TxD serial reset/time and date in RS8-A RS8-A serial reset/time and date in RS8-B RS8-B serial reset/time and date in Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

13 Technical Documentation BNWAS 000 Pin assiments RESET SENSOR -pin Phoenix RM.08 JE SABOT in Sabota RESET in Reset sensor V out Power supply reset sensor V (max. 00 ma) Pin assiments Relay output 9-pin Weidmüller RM. JK K NO. Alarm relay Normally Open K CM. Alarm relay Com K NC. Alarm relay Normally Closed K NO. Alarm relay Normally Open K CM. Alarm relay Com K NC. Alarm relay Normally Closed 7 K NO Fault relay Normally Open 8 K CM Fault relay Com 9 K NC Fault relay Normally Closed Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

14 Technical Documentation BNWAS REATER UNIT Pin assiments WATCH ALARM MAIN UNIT -pin Weidmüller RM. JR Shield RS8-A RS8-A connection to WATCH ALARM MAIN UNIT RS8-B RS8-B connection to WATCH ALARM MAIN UNIT V in Power supply V in ADR 0 Address 0 7 ADR Address 8 N.C. N.C. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

15 Technical Documentation BNWAS SELECTOR UNIT Pin assiments Power supply V DC -pin Weidmüller RM.08 JM V in Power supply V (optional) Shield Pin assiments WATCH ALARM MAIN UNIT -pin Weidmüller RM. JR Shield RS8-A in RS8-A connection to REATER UNIT in RS8-B in RS8-B connection to REATER UNIT in V in Power supply V in Pin assiments REATER UNIT -pin Weidmüller RM. JR...JR Shield RS8-A out RS8-A connection to REATER UNIT out RS8-B out RS8-B connection to REATER UNIT out V out Power supply V out Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

16 Technical Documentation BNWAS RESET UNIT Pin assiments Watch ALARM MAIN UNIT -pin Weidmüller RM. JQ V in Power supply V LED in LED ightness/on/off RESET out Reset Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

17 Technical Documentation BNWAS BOOSTER UNIT Pin assiments Power supply V DC -pin Weidmüller RM.08 JM V ext. Power supply V external Pin assiments WATCH ALARM MAIN UNIT -pin Weidmüller RM. JQ V int. Power supply V internal LED in LED ightness/on/off RESET out Reset Pin assiments RESET UNIT -pin Weidmüller RM.08 JQ0 V out Power supply V out LED out LED ightness/on/off RESET in Reset Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 7 of

18 Technical Documentation BNWAS Current The WATCH ALARM MAIN UNIT supplies the BNWAS (entire system with all associated UNITS) with power. For this reason, the BNWAS must be configured so that the maximum current of the WATCH ALARM MAIN UNIT is not exceeded. Note: Several UNITS can be connected to their own power source and supply other UNITS with power. An EXCEL table for precise calculation of the system configuration is available (Consumption BNWAS xxxxx.xls). 8. Accumulator The accumulator must be dimensioned to supply the BNWAS with power for at least hours. 9. Installation All WATCH ALARM MAIN UNITS, REATER UNIT and SELECTOR UNIT must be installed in a mounting panel (dimensions for cutouts: width = 7 mm, height = mm). The BOOSTER UNIT must be mounted on a top-hat rail in a panel or control cabinet. The RESET UNIT (open frame) must be panel or wall mounted and protected against manipulation with special scre. The RESET UNIT (watertight) must be panel or wall mounted and protected against manipulation with special scre. It should be noted that connectors, cables and housing openings are not accessible and the system is tamper-proof. All components except for the RESET UNIT (watertight) must be installed in closed areas and protected from moisture. 0. Audible sial nerator The tone sequence (characteristic beeping) can be configured via the Service menu. The default setting is a long tone and long interval. The volume should be between 7 db and 8 db. If the internal sial nerator is insufficient, an external audible sial nerator must be connected to JE. The sial nerators for the second and third alarm must be dimensioned and installed according to the applicable standards. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 8 of

19 Technical Documentation BNWAS 000. Reset sensor The reset sensor can be supplied from a V power supply. The current must be less than 00 ma and must not exceed the total current (see Current). A reset may only be performed by persons on the id.. Location The RESET UNITS or WATCH ALARM MAIN UNIT must be clearly visible and easy to reach from the conning position, workstation for navigation, manoeuvring position, workstation for monitoring and id wing. The RESET UNIT and WATCH ALARM MAIN UNIT must be installed to allow easy access. Flashing mushroom buttons (WATCH ALARM MAIN UNIT, RESET UNIT) must be clearly visible to the OOW from any point on the id. The alarm of the WATCH ALARM MAIN UNIT (st alarm) must be clearly audible to the OOW from any point on the id. If external areas are to be included, the external sial nerator output must be used. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 9 of

20 Technical Documentation BNWAS 000. Compass safe distance Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa 0 of

21 Technical Documentation BNWAS 000 Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of

22 Technical Documentation BNWAS 000. Commissioning The BNWAS must be configured as described in the operating instructions (accumulator charging current, REATER UNIT address, configuration menu) followed by a functional test. It must be ensured that no error messas are nerated and all functions work correctly as described. Any faults must be cleared. All standards and specifications relevant for installation must be observed! Following commissioning and acceptance, the configuration must be documented as a basic setting in the Service menu on the connected computer. For this purpose, a "C" for setting the UTC (GMT) time must be sent first, followed by an "s" for the Status/ Configuration menu, and after at least five minutes, an "e" for error messas and finally an "m" for the module list. The stored data must be handed to the customer in the form of a log sheet with date and siature tother with the delivery documents. The configuration data stored on the service computer is archived with the customer order. Tel.: +9 (0)0 / 0 0 * DECKMA GmbH * Fax: +9 (0)0 / 0. Installation instructions Version Pa of