CDB Life Safety Upgrades Facility Wide Choate Mental Health and Development Center Anna, Union County, Illinois

Transcription

1 BIDDING & CONTRACT REQUIREMENTS DATE: June 27, 2014 State of Illinois CAPITAL DEVELOPMENT BOARD Architechniques, Ltd. Mark Feldhake, AIA, LEED AP 817 S. Park Ave. Herrin, Illinois TO: PROSPECTIVE BIDDERS SUBJECT: ADDENDUM NO. 1TO THE BIDDING DOCUMENTS FOR CDB Life Safety Upgrades Facility Wide Choate Mental Health and Development Center Anna, Union County, Illinois This addendum forms a part of the bidding and contract documents and modifies the original bidding documents, dated March 19,2014. Acknowledge receipt of this addendum in space provided on Bid Form. FAILURE TO DO SO MAY SUBJECT BIDDER TO DISQUALIFICATION. ***************************************************************************** PROJECT MANUAL: 1. SECTION ALTERNATE BIDS: AMEND the following text. a. 2.5, A: Alternate Bid No. V4: Deduct/Delete the Ventilating Construction work to provide full life safety upgrades in the following building BG SECTION DOOR HARDWARE: ADD the following manufacturer s products as follows: a. 2.4, 7, o, 1, d: STANLEY COMMERCIAL QDC111 b. 2.4, 7, o, 2, d: STANLEY COMMERCIAL QDC SECTION GLAZING: ADD the following to manufacturer s products as follows: a. 2.4, B, 1, d: SuperLite I by SaftiFirst. b. 2.4, B, 1, e: SuperLite IIXL 60, 90, and 120 by SaftiFirst. 4. SECTION TOILET, BATH AND LAUNDRY ACCESSORIES: ADD the following manufacturer s products as follows: a. 2.1, A, 4: American Specialties, Inc. (ASI) b. 2.1, B, 4: ASI 0030 c. 2.1, C, 4: ASI 0210 d. 2.1, D, 4: ASI 0347 e. 2.1, E, 4: ASI 3700 series CDB Addendum #1

2 f. 2.1, F, 4: ASI 0625 g. 2.2, A, 4: American Specialties, Inc. (ASI) h. 2.2, B, 4: ASI 1224 i. 2.2, C, 4: ASI 1200V j. 2.2, D, 4: ASI 8206L/R k. 2.3, A, 11: American Specialties, Inc. (ASI) l. 2.3, B, 4: ASI 7305 m. 2.3, D, 4: ASI 0953 n. 2.3, E, 4: ASI 7345 o. 2.3, F, 4: ASI 3000 series 5. SECTION ENCLOSURE SWITCHES A. Add the following in the spec section. (BELOW) 2. AUTOMATIC TRANSFER SWITCHES A. Manufacturers: 1. Cummins. 2. ASCO 3. Caterpillar. 4. Zenith 5. Cutler Hammer B. Description: NEMA ICS 2, automatic transfer switch. C. Standard features: BIDDING & CONTRACT REQUIREMENTS 1. Switch ampacity as indicated on oneline diagram, 4 pole switch, rated for 3 phase, wire, 60 Hertz. a. Withstand rating of at least 32,000 amperes. b. Rated at 600 VAC for all classes of load. c. Bus bars: Silverplated copper. d. Capable of closing on loads with inrush fault currents described in ANSI/NRTL Switch shall not contain any integral overcurrent devices in the switching poles to avoid conflict with coordination scheme. e. Transfer Switch SBATS shall be provided with closed transition transfer. D. Locations: Refer to power plan for transfer switch location. E. Transfer switches shall also include: 1. Indicating Lights: Mount in cover of enclosure to indicate NORMAL SOURCE AVAILABLE, ALTERNATE SOURCE AVAILABLE, SWITCH POSITION. CDB Addendum #1

3 BIDDING & CONTRACT REQUIREMENTS Provide switch position indicating contacts. 2. Test Switch: Mount in cover of enclosure to simulate failure of normal source. 3. Return to Normal Switch: Mount in cover of enclosure to initiate manual transfer from alternate to normal source. 4. Normal Source Monitor: Monitor each line of normal source voltage and frequency; initiate transfer when voltage drops below 85 percent or frequency varies more than 3 percent from rated nominal value. 5. Alternate Source Monitor: Monitor alternate source voltage and frequency; inhibit transfer when voltage is below 85 percent or frequency varies more than 3 percent from rated nominal value. 6. Switched Neutral. F. Automatic Sequence of Operation. 1. Initiate Time Delay to Start Alternate Source Engine Generator: Upon initiation by normal source monitor. 2. Time Delay To Start Alternate source Engine Generator: 0 to 15 seconds, adjustable. 3. Initiate Transfer Load to Alternate Source: Upon initiation by normal source monitor and permission by alternate source monitor. 4. Time Delay Before Transfer to Alternate Power Source: 0 to 120 seconds, adjustable. 5. Before transfer to alternate power source initiate disconnect circuit to disconnect large motors for 15 seconds. 6. Initiate Retransfer Load to Normal Source: Upon permission by normal source monitor. 7. Time Delay Before Transfer to Normal Power: 0 to 30 minutes, adjustable; bypass time delay in event of alternate source failure. 8. Time Delay Before Engine Shut Down: 0 to 10 minutes, adjustable, of unloaded operation. 9. Engine Exerciser: Start engine every 7 days; run for 30 minutes before shutting down. Bypass exerciser control if normal source finals during exercising period. 10. Alternate System Exerciser: Transfer loads at each transfer switch to alternate source during engine exerciser period. 6. SECTION : Structured Wiring System A. Section 1.4A, 2: Revise to be "Optical Fiber Singlemode and 62.5micron multimode". B. Section 2.5: Add section to include FIBER OPTIC CABLING: " General: The optical fiber cable construction shall consist of both (6) singlemode and (6) 62.5/125 µm multimode fibers (OM1). These groups and individual fibers shall be identifiable in accordance with ANSI//TIA606. These groups are assembled to form a single compact core, which is covered by a armored protective sheath. Rating: NRTLlisted fiber optic cable Indoor (OFNR) / Outdoor. C. Section 2.6: Add section to include FIBER OPTIC CONNECTORS: "Connectors shall be "SC" duplex type for the singlemode cabling and "ST" type for the multimode cabling. Optical fiber optic connectors shall be capable of terminating optical glass cables with outside diameters ranging from 125 to 900 microns for the multimode cabling and 8 to 10 microns for the singlemode cabling. Fabricate connectors with optical fiber, self centering, axial alignment mechanisms. CDB Addendum #1

4 BIDDING & CONTRACT REQUIREMENTS D. Section 2.7: Add section to include FIBER OPTIC TERMINATION CABINET: "Cabinet shall be wallmounted and shall meet TIA568 and 606 requirements. Cabinet shall be fully populated with the sufficient quantity of load (adapter) plates and adapter/connectors to fully terminate the fiber optic cabling indicated on the electrical drawings and within these specifications." 7. SECTION : Fire Alarm and Smoke Detection System A. Section 1.6A: Add paragraph 13 to read: "DRILL Sequence of Operation: a) Activate local building fire alarm notification appliances; b) Transmit signal to release door hold open devices to maintain fire and/or smoke ratings of the structure. B. Section 2.1B: Add paragraph 16 to read: "At interior of each building's fire alarm system control panel, provide a tone generator with a minimum of four tones in addition to the typical temporal3 tone utilized for fire alarm: weather advisory, medical alarm, lockdown and disaster. Each tone shall be selectable from the Supervising Station at the Power Plant (building 075)." DRAWINGS: 1. SHEET D100.0: Note 9: AMEND to PLUMBING CONTRACTOR TO REMOVE EXISTING HILOW DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A100.0 AND PLUMBING DRAWINGS FOR NEW DRINKING FOUNTAIN LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 2. SHEET D100.1: Note 11: AMEND to PLUMBING CONTRACTOR TO RELOCATE EXISTING HILOW DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A100.1 AND PLUMBING DRAWINGS FOR NEW DRINKING FOUNTAIN LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 3. SHEET D100.2: Note 7: AMEND to PLUMBING CONTRACTOR TO DEMOLISH EXISTING DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A100.2 AND PLUIMBING DRAWINGS FOR NEW DRINKING FOUNTAIN LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 4. SHEET D102.0: Note 9: AMEND to PLUMBING CONTRACTOR TO REMOVE EXISTING DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A102.0 AND PLUMBING DRAWINGS FOR NEW LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED CDB Addendum #1

5 BIDDING & CONTRACT REQUIREMENTS EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 5. SHEET D103.0: Note 6: AMEND to PLUMBING CONTRACTOR TO REMOVE EXISTING DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A103.0 AND PLUMBING DRAWINGS FOR NEW LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 6. SHEET D103.1: Note 10: AMEND to PLUMBING CONTRACTOR TO REMOVE EXISTING DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A103.1 AND PLUMBING DRAWINGS FOR NEW LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 7. SHEET D103.2: Note 7: AMEND to PLUMBING CONTRACTOR TO REMOVE AND REUSE EXISTING DRINKING FOUNTAIN AND CAP LINES. COORDINATE WITH A AND PLUMBING DRAWINGS FOR NEW LOCATION. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. GENERAL CONTRACTOR IS ALSO TO INSTALL NEW HANDRAILING ACROSS OPENING. 8. SHEET D108.1: ADD Note 9: PLUMBING CONTRACTOR TO REMOVE AND RELOCATE EXISTING HILOW DRINKING FOUNTAIN ON WESTERN END OF CORRIDOR 203 AND CAP LINES. COORDINATE WITH PLUMBING DRAWINGS FOR NEW LOCATION OF DRINKING FOUNTAIN. GENERAL CONTRACTOR TO PATCH/REPAIR WALL WITH 20GA. STAINLESS STEEL SHEET WITH ROLLED EDGES AND TAMPER PROOF SCREWS OVER OPENING. 9. SHEET A102.0: ADD Note 16: GENERAL CONTRACTOR TO INSTALL NEW V.C.T. TO TOILET ROOM B102B. 10. SHEET A108.1: ADD Note 21: GENERAL CONTRACTOR TO MODIFY NEW HANDRAILS AROUND RELOCATED DRINKING FOUNTAIN PER DETAIL 10/A SHEETS ALL VENTILATION SHEETS (V100.1, V100.2, V101.1, V101.2, V102.1, V 102.2, V103.1, V103.2, V104.1, V104.2, V105.1, V105.2, V106.1, V107.1): ADD/MODIFY General Note 5: Add/Change to VENTILATION CONTRACTOR TO ADD ½ DUCT LINER AND 1 DUCT WRAP TO NEW SUPPLY, RETURN, AND EXHAUST DUCTS IN CONDITIONED SPACES. VENTILATION CONTRACTOR TO AS 2 DUCT WRAP TO NEW SUPPLY, RETURNS, AND EXHAUST DUCTS IN NON CONDITIONED SPACES. 12. SHEET V102.1: ADD General Note 6: ALL WORK SHOWN WITH SYCAMORE HALL WILL BE PART OF THE BASE BID. ALTERNATE BID V4 WILL BE TO SUBTRACT CDB Addendum #1

6 BIDDING & CONTRACT REQUIREMENTS ALL ASSOCIATED WORK WITH SYCAMORE HALL FROM THE BASE BID EXCEPT FOR THE BARRIER PARTITIONS AS CALLED OUT. 13. SHEET V102.2: ADD General Note 6: ALL WORK SHOWN WITH SYCAMORE HALL WILL BE PART OF THE BASE BID. ALTERNATE BID V4 WILL BE TO SUBTRACT ALL ASSOCIATED WORK WITH SYCAMORE HALL FROM THE BASE BID EXCEPT FOR THE BARRIER PARTITIONS AS CALLED OUT. 14. SHEET P002.0: Note 8: AMEND to SAW CUT EXISTING CONCRETE AND TERRAZZO FLOOR TO EXPOSE SANITARY PIPING. PATCH FLOOR WITH SEALED CONCRETE ONCE NEW WAST PIPING HAS BEEN INSTALLED. 15. SHEET P006.0: Note 8: AMEND to SAW CUT EXISTING CONCRETE AND TERRAZZO FLOOR TO EXPOSE SANITARY PIPING. PATCH FLOOR WITH SEALED CONCRETE ONCE NEW WAST PIPING HAS BEEN INSTALLED. 16. SHEET E0.0: ELECTRICAL SYMBOLS A. FIRE ALARM SYMBOLS: Revise eight symbol from top ("V" inscribed by square with attached triangle) to note "Speaker/Strobe" and not "Horn/Strobe" all audible fire alarm notification devices shall be speaker capable of reproducing voice and tone and not simply a horn appliance. 17. SHEET E0.1: ELECTRICAL PROJECT GENERAL NOTES A. DEMOLITION: Add D9 to read: "For existing systems to be demolished, all raceway and wiring shall be disconnected to the fullest extent possible. Where raceway is above an inaccessible ceiling and cannot be accessed from any sort of existing access panel, light fixture, ceiling cavity, etc., Electrical Contractor may abandon in place; however, wiring shall be disconnected and removed. Raceway and wiring shall be disconnected and fully removed in all other areas that include accessible ceilings (including layin, spline, etc.) or exposed installations." Add D10 to read: "Several buildings include large format exterior annunciator panels that shall be disconnected and removed by the Electrical Contractor under this project. Restore existing surface behind panel to the highest extent possible and provide sealant at all penetrations. E.C. may also have to fabricate new stainless steel or aluminum panel to sufficiently cover backbox for annunciator panel paint cover to match adjacent surfaces, and provide all weather resistant hardware." B. ELECTRICAL GENERAL WORK: Add E4 to read: "After completion of penetrations through floor, electrical contractor shall restore surrounding floor material (carpeting, tile, wood, etc.) to match the existing adjacent surfaces. If floor surface is unable to be restored to match existing, E.C. shall provide collar or plate to fully conceal penetration and match the existing surfaces. E.C. shall also be responsible for repairing or replacing and damaged floor surfaces affected during construction." Add E5 to read: "Electrical contractor shall be responsible for painting all surface raceway, all surface backboxes, and miscellaneous electrical devices to match adjacent surfaces, maintaining a consistent finish with existing devices in same room or building. E. C. Shall be responsible for patching and painting all surfaces (walls, ceilings, etc.) Affected by work in this contract. CDB Addendum #1

7 BIDDING & CONTRACT REQUIREMENTS In any instance where installation of conduit remains exposed, electrical contractor shall paint raceway to match adjacent surfaces. Where raceway is surfacemounted ("exposed) and in finished areas, raceway shall match existing prevalent type (either conduit or surface wireway) and shall be painted (either by factory or electrical contractor) to match the adjacent surfaces. Device backboxes and junction boxes shall also be painted to match the same. Where raceway is exposed and in mechanical, electrical or similaruse rooms or spaces, raceway shall be conduit and shall be painted red, again by factory or E.C. coverplates shall be red as well (backboxes or junction boxes do not also need to be red). Where raceway is installed above an accessible ceiling, raceway shall be conduit and shall be painted red, by factory or E.C. coverplates shall be red as well (again, backboxes and jboxes do not also need to be red). Add E6 to read: "Majority of interior routing of power wiring and fire alarm cabling has not been indicated on individual building electrical plans. Other then where specifically noted on plans, electrical contractor shall determine best routing in the field. All cable routing is only suggested path based on casual field observations. Actual cable and raceway routing shall be determined by contractor with equipment requirements prior to installation. Indicate actual installed cabling, raceways, device addresses & routing in record documents." Add E7 to read: "New ceiling or wallmounted devices are indicated at best approximated location. If existing device (e.g. light fixture, fire alarm smoke detector, or architectural appliance) conflicts with indicated location, move new device to nearest location without obstruction. If new location is in question, contact a/e or university's representative (i.e. building engineer) for verification." C. FIRE ALARM WORK: Revise F2 to read: "All remote power supplies shown shall be monitored and controlled by remote fire alarm modules. Provide modules, boxes, and cabling adjacent to each location. Exact locations of remote power supplies may vary depending upon existing equipment or potential obstructions at indicated location. E.C. may use an alternate location adjacent existing electrical panel, contingent upon review by a/e and university. Provide smoke detector in close proximity of each power supply." Add F4 to read: "Where permanent fixture or obstruction prohibits location or acceptable mounting height of notification appliance, E.C. may substitute ceilingmounted device for wallmounted unit, contingent upon review of section NFPA 72 spacing requirements (2010 edition)." Add F5 to read: "Existing fire alarm is to be kept in full operation during construction, and shall only be disconnected once the new system is fully programmed and functional. The one caveat to this operation involves the provisions of a fire watch while either systems are nonrational. E.C. shall furnish, at their own expense, a fire watch during these periods." D. Delete fire alarm system oneline diagram depicted by detail #2 (common signaling) retain oneline diagram / detail #1. Add the following buildings to the listing: BG029 (Greenhouse), BG047 (Carwash), BG114 (Therapy Pool), BG115 (Chapel). ALL buildings (28 total) shall now include voice evacuation. 18. SHEET E1.0: ELECTRICAL SITE PLAN and ALTERNATE BIDS LISTING A. Revise keyed note 1 to read: EC shall provide fire alarm work under base bid and provide life safety upgrades under alternate bid E SHEET E1.3: ELECTRICAL SITE TUNNEL PLAN CDB Addendum #1

8 BIDDING & CONTRACT REQUIREMENTS A. Revise general note 1 to include: " Each building shall include (1) 6strand singlemode and (1) 6strand 62.5um multimode indoor/outdoor hybrid fiber optic cable (both fiber optic cables shall be under a single armored hybrid/composite jacket) from its FTC to a similar highdensity cabinet at Building 075 ". All other notes shall remain. Revise ALL references on the actual tunnel plan from 62.5um multimode to include singlemode and for the cable to be hybrid and armored. B. Add keyed note 1 to Goodner Hall (BG009) to read: "Existing fire alarm system includes combined aerial / underground communication cable between Goodner Hall and Staff Cottage #4 (BG108) using same route, extend (7) new singlemode/multimode fiber optic cables (detailed by General Note 1) from Goodner to Staff Cottage #4. Then from Staff Cottage #4, provide (1) new singlemode/multimode fiber optic cable of the same type to each of the six other cottages (BG044, BG045, BG109, BG107, BG106, BG105). Provide fiber optic cable in (1) 1" underground conduit (with tracer wire) at a minimum of 30" below grade to each of the six cottages. Provide all necessary trenching (and/or directional boring) and site restoration to existing conditions upon completion of trench / boring activities." C. Add keyed note 2 to Fire House / Carwash (BG047) to read: "Provide (1) new singlemode/multimode fiber optic cable (detailed by General Note 1) from fiber termination cabinet (FTC) adjacent fire alarm control panel at Carwash to Chapel (BG115). Provide fiber optic cable in (1) 1" underground conduit (with tracer wire) at a minimum of 30" below grade. Provide all necessary trenching (and/or directional boring) and site restoration to existing conditions upon completion of trench/boring activities." D. Add keyed note 3 to Therapy Pool (BG114) to read: "Provide (1) new singlemode/multimode fiber optic cable (detailed by General Note 1) from fiber termination cabinet (FTC) adjacent fire alarm control panel at Therapy Pool to Dewey Cottage (BG017). Provide fiber optic cable in (1) 1" underground conduit (with tracer wire) at a minimum of 30" below grade. Provide all necessary trenching (and/or directional boring) and site restoration to existing conditions upon completion of trench/boring activities." E. Add keyed note 4 to Chapel (BG115) to read: "Provide (2) new singlemode/multimode fiber optic cable (detailed by General Note 1) from fiber termination cabinet (FTC) adjacent fire alarm control panel at Chapel to Dewey Cottage (BG017). Provide fiber optic cable in (1) 1" underground conduit (with tracer wire) at a minimum of 30" below grade. Provide all necessary trenching (and/or directional boring) and site restoration to existing conditions upon completion of trench/boring activities." F. Add keyed note 5 to Greenhouse (BG029) to read: "Provide (1) new singlemode/multimode fiber optic cable (detailed by General Note 1) from fiber termination cabinet (FTC) adjacent fire alarm control panel at Greenhouse to existing service tunnel to the south. Provide fiber optic cable in (1) 1" underground conduit (with tracer wire) at a minimum of 30" below grade. Provide all necessary trenching (and/or directional boring) and site restoration to existing conditions upon completion of trench/boring activeties." G. Revise quantity of fiber optic cables between BG107 (Dewey Cottage) and intersection of tunnel to the west of BG018 (Rehab Services Bldg.) to be (4) in lieu of (1); revise quantity to the south of the intersection to now be (6) in lieu of (2). CDB Addendum #1

9 BIDDING & CONTRACT REQUIREMENTS H. Revise quantity of fiber optic cables between BG031 (Athlon Cottage) and intersection of tunnel to the east of BG022 (Life Skills) to be (2) in lieu of (1); revise quantity of fiber optic cables to the west of the same intersection to be (3) in lieu of (2). I. Revise quantity of fiber optic cables between BG019 (Bakery/Cannery) and BG034 (Barnes Hall) to be (26) in lieu of (21); revise quantity of fiber optic cables between BG034 (Barnes Hall) and BG075 (Power Plant) to be (27). 20. SHEET E1.4: ELECTRICAL SITE PLAN and ALTERNATE BIDS LISTING A. Revise the temporary transformer to be 4160v in lieu of 12470v. 21. SHEET DE001.0: MAIN BUILDING (BG001) BASEMENT DEMOLITION A. Revise the light fixture being demolition in corr B25, stor B24, stor. B27 and corr B29. See attached sheet DE001.1 ADD1(A). 22. SHEET E001.0: MAIN BUILDING (BG001) BASEMENT A. Revise the light fixture being installed in corr B25, stor B24, stor. B27 and corr B29. See attached sheet E001.1 ADD1(A). B. Add keyed note 2 next to FACP. Keyed note 2 shall read EC shall provide (2)#12 and (1)#12 ground in 3/4" conduit from panel A circuit #1. Add panel A to the east wall north of Mech B20 in the room with FACP. 23. SHEET E002.0: CEDAR HALL (BG002) BASEMENT A. Add circuit to FACP002, panel LS0(002)11,13. Provide (4)#12 and (1)#12 in 3/4" conduit from panel to FACP. B. Add circuit to FACP003, panel LS0(002)15,17. Provide (4)#12 and (1)#12 in 3/4" conduit from panel to FACP. 24. SHEET E002.1: CEDAR HALL (BG002) 1ST FLOOR A. Add lighting control contactor next to panel LS1(002). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add keyed note 6 to lighting control contactor. Keyed note 6 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E002.1, see attached sheet E002.1 ADD1(A). D. Add (2) 20 amp single pole breaker to panel LS1(002). E. Add (4) control monitor for the smoke dampers between dining room 225 and 5 person bedroom 223. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(002) SHEET E002.2: CEDAR HALL (BG002) 2ND FLOOR A. Add (4) control monitor for the smoke dampers between dining room 125 and 4 person bedroom 123. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(002) SHEET E002.4: ELECTRICAL DETAIL BG002, BG003, BG004 A. Add keyed note #6 to ATS LS SHEET E003.1: DOGWOOD HALL (BG003) 1ST FLOOR A. Add lighting control contactor next to panel LS1(003). The new wall pack C fixture shall be circuited to the lighting contactor. CDB Addendum #1

10 BIDDING & CONTRACT REQUIREMENTS B. Add keyed note 6 to lighting control contactor. Keyed note 6 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E008.1, see attached sheet E003.1 ADD1(A). D. Add (2) 20 amp single pole breaker to panel LS1(003). E. Add (2) control monitor for the smoke dampers for stair 142. (1) between stair 142 and restroom 104 and (1) between stair 142 and corr 141. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(003)10. F. Add (2) control monitor for the smoke dampers for stair 137. (2) between stair 137 and corr 138. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(003)10. G. Add (2) control monitor for the smoke dampers for stair 135. (1) between stair 135 and laundry 130 and (1) between stair 135 and corr 136. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(003) SHEET E003.2: DOGWOOD HALL (BG003) 2ND FLOOR A. Add (3) control monitor for the smoke dampers for stair 137. (2) between stair 137 and linen 220 and (1) between stair 137 and lobby 237. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(003) SHEET E004.0: CYPRUS HALL (BG004) BASEMENT A. Add circuit to FACP004, panel LS0(004)9,11. Provide (4)#12 and (1)#12 in 3/4" conduit from panel to FACP. B. Add keyed note 7 in electrical room B116. Note 7 shall read Provide (4)#10 and (1)#10 ground from the 3/4" conduit to the temporary generator from the existing emergency panel for the generator heater and charger.. Provide (2) 20amp single pole breakers in the GE AQF panel. 30. SHEET E004.1: CYPRUS HALL (BG004) 1ST FLOOR A. Add lighting control contactor next to panel LS1(004). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add keyed note 6 to lighting control contactor. Keyed note 6 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E008.1, see attached sheet E004.1 ADD1(A). D. Add (2) 20 amp single pole breaker to panel LS1(004). E. Add (2) control monitor for the smoke dampers for stair 154. (1) between stair 152 and sally port 153 and (1) between stair 154 and person room 100. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(004)12. F. Add (2) control monitor for the smoke dampers for stair 149. (1) between stair 149 and corr 151 and (1) between stair 149 and sally port 150. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(004)12. G. Add (2) control monitor for the smoke dampers for stair 144. (1) between stair 144 and sally port 145 and (1) between stair 144 and laundry room 142. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(004) SHEET E004.2: CYPRUS HALL (BG004) 2ND FLOOR A. Add (3) control monitor for the smoke dampers for stair 149. (2) between stair 149 and staff tlt 222 and (1) between stair 149 and sally port 242. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(004)12. CDB Addendum #1

11 B. Revise the location of panel LS2(004) to Jan 228 west wall. BIDDING & CONTRACT REQUIREMENTS 32. SHEET E006.0: REDBUD HALL (BG006) BASEMENT A. Add circuit to FACP LS0(006)11,13. Provide (4)#12 and (1)#12 in 3/4" conduit from panel to FACP. 33. SHEET E006.1: REDBUD HALL (BG006) 1ST FLOOR A. Add lighting control contactor next to panel LS1(006). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add keyed note 10 to lighting control contactor. Keyed note 10 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E006.1, see attached sheet E006.1 ADD1(A). Add (2) 20 amp single pole breaker to panel LS1(006). D. Add keyed note 11 to metal gate in the courtyard. Keyed note 11 shall read EC shall disconnect the existing magnetic door holder. EC shall protect the circuit and conductors. EC shall provide connection to the new magnetic door holder. E. Add (2) control monitor for the smoke dampers for stair 142. (2) between stair 142 and corr 144. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(006)12. F. Add (1) control monitor for the smoke dampers between office 110 and break room 108. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(006)12. G. Add (2) control monitor for the smoke dampers for office 116. (1) between office 116 and breaker room 108 and (1) between office 116 and corr 141. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(006) SHEET E006.2: REDBUD HALL (BG006) 2ND FLOOR i. Add (2) control monitor for the smoke dampers in the pent house next to stair 142. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(006) SHEET E007.1: DOGWOOD HALL (BG007) 1ST FLOOR A. Add lighting control contactor next to panel LS1(007). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add keyed note 9 to lighting control contactor. Keyed note 9 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E007.1, see attached sheet E007.1 ADD1(A). D. Add (2) 20 amp single pole breaker to panel LS1(007). E. Add (2) control monitor for the smoke dampers for stair 144. (1) between stair 144 and toilet 106 and (1) between stair 144 and corr 143. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(007)14. F. Add (2) control monitor for the smoke dampers for stair 137. (2) between stair 137 and corr to the west of stair 137. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(007)14. G. Add (2) control monitor for the smoke dampers for stair 135. (1) between stair 135 and laundry 132 and (1) between stair 135 and corr 136. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(007) SHEET E007.2: DOGWOOD HALL (BG007) 2ND FLOOR CDB Addendum #1

12 BIDDING & CONTRACT REQUIREMENTS A. Add (3) control monitor for the smoke dampers for stair 137. (2) between stair 137 and storage 222 and (1) between stair 137 and corr 239. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(007) SHEET E008.0: MAGNOLIA HALL (BG008) BASEMENT A. Add circuit to FACP008 LS1(008)11,13 and FACP007 LS1(008)15,17. B. Add panel LS0(008) in room Elec C. Add keyed note 3 in electrical room B116. Note 3 shall read Provide (4)#10 and (1)#10 ground from the 3/4" conduit to the temporary generator from the existing emergency panel for the generator heater and charger. Provide (2) 20amp single pole breakers in the GE AQF panel. 38. SHEET E008.1: MAGNOLIA HALL (BG008) 1ST FLOOR A. Add lighting control contactor next to panel LS1(008). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add keyed note 9 to lighting control contactor. Keyed note 9 shall read Lighting contactor shall control C fixtures. See contactor detail on this sheet. C. Add attached lighting contactor to the E008.1, see attached sheet E008.1 ADD1(A). D. Add (5) 20 amp single pole breaker to panel LS1(008). E. Add keyed note 10 to metal gate in the courtyard. Keyed note 10 shall read EC shall disconnect the existing magnetic door holder. EC shall protect the circuit and conductors. EC shall provide connection to the new magnetic door holder. F. Add (2) control monitor for the smoke dampers for stair 148. (1) between stair 142 and storage 144 and (1) between stair 148 and corr 152. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(008)14. G. Add (2) control monitor for the smoke dampers for stair 147. (1) between stair 147 and corr 150 and (1) between stair 147 and corr 151 Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(008)14. H. Add (2) control monitor for the smoke dampers for stair 145. (1) between stair 145 and house keeping 121 and (1) between stair 145 and corr 149. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(008) SHEET E008.2: MAGNOLIA HALL (BG008) 2ND FLOOR A. Add (3) control monitor for the smoke dampers for stair 147. (2) between stair 147 and toilet 231 and (1) between stair 147 and corr 249. Provide (2)#12 and (1)#12 in 3/4" conduit from panel LS1(008) SHEET DE009.0: GOODNER HALL (BG009) BASEMENT DEMOLITION A. Add sheet in its interiority. 41. SHEET E009.0: GOODNER HALL (BG009) BASEMENT A. Add keyed note 3 next to the FACP. Keyed note 3 shall read Provide (4)#12 and (1)#12 ground in 3/4" from the FACP and AMP to emergency panel in mechanical 005. FACP and AMP shall be circuited to the (2) spare 20amp 1 pole breaker in the emergency panel. CDB Addendum #1

13 BIDDING & CONTRACT REQUIREMENTS 42. SHEET E009.0: GOODNER HALL (BG009) BASEMENT A. Add, FACP and AMP shall be circuited to LS1(022)8,12 (provide (2) 20amp breaker in panel LS1(022)). Provide (4)#12 and (1)#12 ground in 3/4" conduit from FACP to LS1(022). 43. SHEET E017.0: DEWEY COTTAGE (BG017) BASEMENT A. Add, FACP and AMP shall be circuited to existing panel A on west wall in Classroom B1 circuit number 4 and 6. Provide (4)#12 and (1)#12 ground in 3/4" conduit from FACP to panel. 44. SHEET E033.1: OAK HALL (BG033) 1ST FLOOR A. Add keyed note 15 to lighting control contactor. Keyed note 15 shall read Lighting contactor shall control C fixtures. See contactor detail on E B. Add (1) B fixtures and (1) switch next to the door in the new (4) mechanical spaces, one on each corner of the building. The new B fixture between mech 262 and 261 shall be circuited to LS1(003)5. The new B fixture between mech 245 and 246 shall be circuited to LS1(003)5. The new B fixture between mech 227 and 226 shall be circuited to LS1(003)3. The new B fixture between mech 213 and 212 shall be circuited to LS1(003)3. C. Add GFIC receptacle on the south wall off 2 person bedroom 219 in the corridor side for the new water cooler. The receptacle shall be circuited to the existing panel B. Provide (2)#12 and (1)#12ground in 3/4" from the receptacle to the panel. Use blank breaker in the panel for water cooler. Coordinate location with attached plumbing sheet. 45. SHEET E033.2: ELECTRICAL DETAILS (BG033) A. Add lighting control contactor next to panel LS1(033). The new wall pack C fixture shall be circuited to the lighting contactor. B. Add attached lighting contactor to the E033.2, see attached sheet E033.2 ADD1(A). C. Add (1) 20 amp single pole breaker to panel LS1(033). 46. SHEET E029: GREENHOUSE (BG029) BASEMENT and FIRST FLOOR A. Revise fire alarm communicator / transmitter (C/T) at west wall of Stor 001 to be NIC network interface card (fiber optic). Add fiber termination cabinet (FTC) and amplifier (AMP) to system for voice evacuation. 47. SHEET E044: COTTAGE #6 (BG044) 1ST FLOOR and BASEMENT A. Add Keyed note 13 to read Provide (2)#12 and (1)#12 ground from the exit sign to the inverter. See detail 2 on sheet E5.0 B. Add (3) fixtures to be demoed in storage 001 (in basement). Add (3) A fixtures to be installed in the new ceiling in the basement. See attached sheet E044 ADD1(A). 48. SHEET E045: COTTAGE #7 (BG045) 1ST FLOOR and BASEMENT A. Add (3) fixtures to be demoed in storage 001 (in basement). Add (3) A fixtures to be installed in the new ceiling in the basement. The work is the same is the same as E044 ADD1(A). CDB Addendum #1

14 BIDDING & CONTRACT REQUIREMENTS 49. SHEET E047: CARWASH/FIREHOUSE (BG047) 1ST FLOOR and ATTIC A. Revise fire alarm communicator / transmitter (C/T) at north wall of Fire Truck Room (100) to be NIC network interface card (fiber optic). Add fiber termination cabinet (FTC) and amplifier (AMP) to system for voice evacuation. 50. SHEET E144: THERAPY POOL (BG047) 1ST FLOOR A. Revise fire alarm communicator / transmitter (C/T) at north wall of Fire Truck Room (100) to be NIC network interface card (fiber optic). Add fiber termination cabinet (FTC) and amplifier (AMP) to system for voice evacuation. 51. SHEET E145: CHAPEL (BG115) FIRST FLOOR A. Revise fire alarm communicator / transmitter (C/T) at north wall of Mechanical 106 to be NIC network interface card (fiber optic). Add fiber termination cabinet (FTC) and amplifier (AMP) to system for voice evacuation. 52. SHEET FA006.1: REDBUD HALL (BG006) 1ST FLOOR FIRE ALARM A. Revise fire alarm control panel (FACP) at east wall of Corr. 139 to be an annunciator panel (FAAP). 53. SHEET FA020.0: KITCHEN/CAFETERIA (BG020) 1ST FLOOR FIRE ALARM A. Add, FACP and AMP shall be circuited to existing KP7 panel on the wall next to the FACP, circuit number 18 and 20. Provide (4)#12 and (1)#12 ground in 3/4" conduit from FACP to KP7 panel. Add keyed note 2 and panel KP7 on the north wall office 110. Keyed note 2 shall read Provide (3) new 20 amp 1 pole breakers in panel KP7 for FACP, AMP and door holder. Panel KP7 is a GE AQF panel. B. Add note to door holder to read KP722. Add keyed note 3 next to door holder control module to read EC shall provide a junction box above each door holder with the indicated circuit. EC shall connect (2)#12 and (1)#12 ground to the door holder. 54. SHEET FA021.1: GENERAL STORE (BG021) 1ST FLOOR FIRE ALARM A. Add, FACP and AMP shall be circuited to existing panel A on the north wall in storage room 108, circuit number 15 and 14. Provide (4)#12 and (1)#12 ground in 3/4" conduit from FACP to existing panel A. 55. SHEET FA034.0: BG034 (BARNES HALL) BASEMENT A. Add, FACP and AMP shall be circuited to existing panel A on the east wall in mech room B2, circuit number 42 and 40. Provide (4)#12 and (1)#12 ground in 3/4" conduit from FACP to existing panel A. Add keyed note 1 and panel A on the west wall mech B2. Keyed note 2 shall read Provide (2) new 20 amp 1 pole breakers in panel A for FACP, AMP and door holder. Panel A is a square D QCL panel. 56. SHEET P033: PLUMBING BASE BID BG033 A. Existing bilevel drinking fountain shall be moved as indicated on sketch P033 ADD 1(A). CDB Addendum #1

15 BIDDING & CONTRACT REQUIREMENTS 57. SHEET P047: PLUMBING BASE BID BG047 A. Keyed note on the DEMO PLAN shall be labeled 14 instead of 4. See sketch P047 ADD1(A). CLARIFICATION: 1. Question came up during the walk through about who will be patching the holes left from the electrical demo work. 1) See Project General Note #2 on sheet E Do the temporary generator feeders have to be in conduit in the crawl space? 1) The temporary generator feeders do not have to be in conduit in the crawl space. The feeder has to be supported from the structure. Also, the feeders have to be in conduit outside and in the crawl space. The temporary generator feeders shall be removed by the EC. BID DATE: 1. This Addendum does not alter the previously published bid date(s). Very truly yours, 06/30/14 Mark Feldhake, AIA, LEED AP This addendum consists of 28 pages. Attachment P033 ADD1 P047ADD1 DE001.0 ADD1 DE009.0 E001.0 ADD1 E002.1 ADD1 E003.1 ADD1 E004.1 ADD1 E006.1 ADD1 E007.1 ADD1 E008.1 ADD1 E033.2 ADD1 E044.2 ADD1 11/14/30 CDB Addendum #1

16

17

18

19

20

21

22

23

24

25

26

27

28