HYTRONIC WITH SSPS USER GUIDE Recommended for Single Supply HyTronic Faucets Only

Transcription

1 Cleanng or Replacng Inlet Flter Close supply valves Dsconnect braded hoses and clean or replace flter (for a new flter, see "common replacement parts") Connect braded hoses wth flter to supply valves and fully open. HYTRONIC WITH SSPS USER GUIDE Recommended for Sngle Supply HyTronc Faucets Only SAFETY INFORMATION Read ths entre user gude to ensure proper nstallaton. Complance and conformty to local codes and ordnances s the responsblty of the nstaller. The followng safety notes must always be compled wth durng handlng of ths product: Make sure there s enough space and lghtng avalable durng nstallaton and servce Do not modfy or convert ths Chcago Faucets product yourself. All warrantes wll be voded. IMPORTANT Installaton may be performed at dfferent tmes of constructon by dfferent ndvduals. For ths reason, these nstructons should be left on-ste wth the faclty or mantenance manager. Pressurzed plumbng fxtures shall be nstalled n accordance wth manufacturer s recommendatons. The supply ppng to these devces shall be securely anchored to the buldng structure to prevent nstalled devce from unnecessary movement when operated by the user. Care shall be exercsed when nstallng the devce to prevent marrng the exposed sgnfcant surface. Do not use ppe dope. Flush all the water supply lnes before makng connectons. Result The flter s now cleaned or replaced. Cleanng or Replacng Aerator Remove shut-off screw Tradtonal Lavatory Contemporary Lavatory Remove outlet wth vandal resstant wrench suppled wth the faucet. Clean or replace outlet, then renstall Install shut-off screw Gooseneck Wallmount SSPS Generator Result The outlet s now cleaned or replaced rev.0/

2 CF HyTronc_SSPS_Install SSPS // 9: AM Page Ths faucet comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Plumber s Putty Adjustable Lockng Plers Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. Mountng of Deck Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. Do not tghten locknut before step s completed. Mount cover plate f requred. Plumber s putty s recommended to seal cover plate to the snk. Securty pn must be located on the left sde. Mountng of Wall Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. The SSPS Generator comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Hand Drll Adjustable Lockng Plers Fully open supply valve. Includes SSPS Generator Unt Electroncs Module and Holder Green Power Adapter Hose If the faucet does not work as descrbed below, see Troubleshootng secton Hold hand n front of sensor - Water flow starts. Aerator:.0 gpm (standard) and optonal 0. gpm nsert CARE AND MAINTENANCE A battery model s shown n the followng example. These nstructons apply to all models. After 0 mnutes, the "Manual Settng" mode wll be dsabled automatcally and all settngs wll be saved. Faucet Adjustments Operatng modes and sensor ranges can be adjusted wth a manual operaton through the nfrared sensor. A tradtonal lavatory faucet s shown as an example. Faucet adjustment operatons apply to all models. Alternatvely, operatng modes and sensor ranges can be adjusted wth a Commander Handheld Programmng Unt. For more nformaton, vst our webste at Water supply valve s open Mount gasket, put faucet nto openng and tghten Place nut onto mountng rod and tghten wth wrench. If faucet was nstalled wth cover plate, secure wth basn washer, flat washer and locknut. Install aerator and tghten wth aerator key (suppled). Aerator:.0 gpm (standard) and optonal 0. gpm nsert Result The Deck Mount faucet s now mounted. Insert green adapter OPERATING MODES Poston SSPS under snk. Carefully poston to allow connecton of water lnes and wrng. housng vertcally Warnng: Hot water may burn your skn. Hold hand carefully under water and remove quckly. Mark holes. Poston mountng bracket and mark mountng holes. C: Meterng Mode (0 s) D: Scrub Mode (0 s) Remove housng vertcally Mount housng vertcally E: Scrub Mode (0 s) F: Sensor Range Adjustment Connect wrng. Remove cover and connect faucet wre to SSPS and secure nto wre harness. G: Reset Mount gasket and put faucet nto snk. Mount bracket from underneath. Place hoses through large openng and mountng rod through small openng. Make sure flange sts securely aganst surface. Remove all tems from snk. Connect faucet to SSPS unt. Attached to faucet and nstall water supply lne. Install flter at ths pont. Install aerator and tghten wth aerator key (suppled) For gooseneck faucets, tghten spout wth wrench. Aerator:.0 gpm (standard) and optonal 0. gpm nsert Remove shut-off screw Result The faucet s now tested. In order to set the operatng modes, the faucet needs to be placed nto "Manual Settng" mode. At ths tme, operatng modes can be changed wthn the next 0 mnutes.the followng s a functonal dagram to show the dfferent settngs avalable for manual faucet adjustment. FUNCTION DIAGRAM OF OPERATING MODES Result The "Manual Settng" Mode s now enabled. Water pulses n seconds [s] Modes A - Cleanng Mode Drll holes. Drll holes for screw anchors. Secure SSPS to wall. Insert anchors nto holes and mount SSPS unt to wall wth suppled screws. Wat for seconds for faucet to calbrate to ts envronment. Result The faucet s now actvated. Descrpton The faucet s nactve for 90 seconds. The faucet s actvated f t senses a hand presence. Ths s the default operatng mode of the faucet. The faucet wll shut off after 0 seconds regardless of hand presence detected. The faucet wll shut off 0 seconds after the detecton of the last hand presence. The faucet wll shut off 0 seconds after the detecton of the last hand presence. Change the detecton dstance of the nfrared sensor. The default sensor range s approxmately " beyond the spout. All settngs wll be reset to orgnal factory settngs. Mount shut-off screw Remove green adapter from holder 0 Attach cover. Faucet s ready to run through programmng sequence. Remove protectve coverng from sensor. Enablng Manual Settng Mode Operatng Modes A: Cleanng Mode B: Normal Mode Result The Wall Mount faucet s now mounted. Test Functon Mountng of SSPS Generator 9 Attach to supply. Attach nlet hose to supply and turn on water. Wth water on, check system for leaks. Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. The followng procedure (a, b, c) must be done three () tmes n a row. a - Rensert green adapter b - LED lghts up c - Remove green adapter mmedately after LED swtches off a B - Normal Mode c C - Meterng Mode 0 s D - Scrub Mode 0 s E - Scrub Mode 0 s b Legend: Water s off Water s on

3 CF HyTronc_SSPS_Install SSPS // 9: AM Page Ths faucet comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Plumber s Putty Adjustable Lockng Plers Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. Mountng of Deck Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. Do not tghten locknut before step s completed. Mount cover plate f requred. Plumber s putty s recommended to seal cover plate to the snk. Securty pn must be located on the left sde. Mountng of Wall Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. The SSPS Generator comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Hand Drll Adjustable Lockng Plers Fully open supply valve. Includes SSPS Generator Unt Electroncs Module and Holder Green Power Adapter Hose If the faucet does not work as descrbed below, see Troubleshootng secton Hold hand n front of sensor - Water flow starts. Aerator:.0 gpm (standard) and optonal 0. gpm nsert CARE AND MAINTENANCE A battery model s shown n the followng example. These nstructons apply to all models. After 0 mnutes, the "Manual Settng" mode wll be dsabled automatcally and all settngs wll be saved. Faucet Adjustments Operatng modes and sensor ranges can be adjusted wth a manual operaton through the nfrared sensor. A tradtonal lavatory faucet s shown as an example. Faucet adjustment operatons apply to all models. Alternatvely, operatng modes and sensor ranges can be adjusted wth a Commander Handheld Programmng Unt. For more nformaton, vst our webste at Water supply valve s open Mount gasket, put faucet nto openng and tghten Place nut onto mountng rod and tghten wth wrench. If faucet was nstalled wth cover plate, secure wth basn washer, flat washer and locknut. Install aerator and tghten wth aerator key (suppled). Aerator:.0 gpm (standard) and optonal 0. gpm nsert Result The Deck Mount faucet s now mounted. Insert green adapter OPERATING MODES Poston SSPS under snk. Carefully poston to allow connecton of water lnes and wrng. housng vertcally Warnng: Hot water may burn your skn. Hold hand carefully under water and remove quckly. Mark holes. Poston mountng bracket and mark mountng holes. C: Meterng Mode (0 s) D: Scrub Mode (0 s) Remove housng vertcally Mount housng vertcally E: Scrub Mode (0 s) F: Sensor Range Adjustment Connect wrng. Remove cover and connect faucet wre to SSPS and secure nto wre harness. G: Reset Mount gasket and put faucet nto snk. Mount bracket from underneath. Place hoses through large openng and mountng rod through small openng. Make sure flange sts securely aganst surface. Remove all tems from snk. Connect faucet to SSPS unt. Attached to faucet and nstall water supply lne. Install flter at ths pont. Install aerator and tghten wth aerator key (suppled) For gooseneck faucets, tghten spout wth wrench. Aerator:.0 gpm (standard) and optonal 0. gpm nsert Remove shut-off screw Result The faucet s now tested. In order to set the operatng modes, the faucet needs to be placed nto "Manual Settng" mode. At ths tme, operatng modes can be changed wthn the next 0 mnutes.the followng s a functonal dagram to show the dfferent settngs avalable for manual faucet adjustment. FUNCTION DIAGRAM OF OPERATING MODES Result The "Manual Settng" Mode s now enabled. Water pulses n seconds [s] Modes A - Cleanng Mode Drll holes. Drll holes for screw anchors. Secure SSPS to wall. Insert anchors nto holes and mount SSPS unt to wall wth suppled screws. Wat for seconds for faucet to calbrate to ts envronment. Result The faucet s now actvated. Descrpton The faucet s nactve for 90 seconds. The faucet s actvated f t senses a hand presence. Ths s the default operatng mode of the faucet. The faucet wll shut off after 0 seconds regardless of hand presence detected. The faucet wll shut off 0 seconds after the detecton of the last hand presence. The faucet wll shut off 0 seconds after the detecton of the last hand presence. Change the detecton dstance of the nfrared sensor. The default sensor range s approxmately " beyond the spout. All settngs wll be reset to orgnal factory settngs. Mount shut-off screw Remove green adapter from holder 0 Attach cover. Faucet s ready to run through programmng sequence. Remove protectve coverng from sensor. Enablng Manual Settng Mode Operatng Modes A: Cleanng Mode B: Normal Mode Result The Wall Mount faucet s now mounted. Test Functon Mountng of SSPS Generator 9 Attach to supply. Attach nlet hose to supply and turn on water. Wth water on, check system for leaks. Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. The followng procedure (a, b, c) must be done three () tmes n a row. a - Rensert green adapter b - LED lghts up c - Remove green adapter mmedately after LED swtches off a B - Normal Mode c C - Meterng Mode 0 s D - Scrub Mode 0 s E - Scrub Mode 0 s b Legend: Water s off Water s on

4 CF HyTronc_SSPS_Install SSPS // 9: AM Page Ths faucet comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Plumber s Putty Adjustable Lockng Plers Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. Mountng of Deck Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. Do not tghten locknut before step s completed. Mount cover plate f requred. Plumber s putty s recommended to seal cover plate to the snk. Securty pn must be located on the left sde. Mountng of Wall Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. The SSPS Generator comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Hand Drll Adjustable Lockng Plers Fully open supply valve. Includes SSPS Generator Unt Electroncs Module and Holder Green Power Adapter Hose If the faucet does not work as descrbed below, see Troubleshootng secton Hold hand n front of sensor - Water flow starts. Aerator:.0 gpm (standard) and optonal 0. gpm nsert CARE AND MAINTENANCE A battery model s shown n the followng example. These nstructons apply to all models. After 0 mnutes, the "Manual Settng" mode wll be dsabled automatcally and all settngs wll be saved. Faucet Adjustments Operatng modes and sensor ranges can be adjusted wth a manual operaton through the nfrared sensor. A tradtonal lavatory faucet s shown as an example. Faucet adjustment operatons apply to all models. Alternatvely, operatng modes and sensor ranges can be adjusted wth a Commander Handheld Programmng Unt. For more nformaton, vst our webste at Water supply valve s open Mount gasket, put faucet nto openng and tghten Place nut onto mountng rod and tghten wth wrench. If faucet was nstalled wth cover plate, secure wth basn washer, flat washer and locknut. Install aerator and tghten wth aerator key (suppled). Aerator:.0 gpm (standard) and optonal 0. gpm nsert Result The Deck Mount faucet s now mounted. Insert green adapter OPERATING MODES Poston SSPS under snk. Carefully poston to allow connecton of water lnes and wrng. housng vertcally Warnng: Hot water may burn your skn. Hold hand carefully under water and remove quckly. Mark holes. Poston mountng bracket and mark mountng holes. C: Meterng Mode (0 s) D: Scrub Mode (0 s) Remove housng vertcally Mount housng vertcally E: Scrub Mode (0 s) F: Sensor Range Adjustment Connect wrng. Remove cover and connect faucet wre to SSPS and secure nto wre harness. G: Reset Mount gasket and put faucet nto snk. Mount bracket from underneath. Place hoses through large openng and mountng rod through small openng. Make sure flange sts securely aganst surface. Remove all tems from snk. Connect faucet to SSPS unt. Attached to faucet and nstall water supply lne. Install flter at ths pont. Install aerator and tghten wth aerator key (suppled) For gooseneck faucets, tghten spout wth wrench. Aerator:.0 gpm (standard) and optonal 0. gpm nsert Remove shut-off screw Result The faucet s now tested. In order to set the operatng modes, the faucet needs to be placed nto "Manual Settng" mode. At ths tme, operatng modes can be changed wthn the next 0 mnutes.the followng s a functonal dagram to show the dfferent settngs avalable for manual faucet adjustment. FUNCTION DIAGRAM OF OPERATING MODES Result The "Manual Settng" Mode s now enabled. Water pulses n seconds [s] Modes A - Cleanng Mode Drll holes. Drll holes for screw anchors. Secure SSPS to wall. Insert anchors nto holes and mount SSPS unt to wall wth suppled screws. Wat for seconds for faucet to calbrate to ts envronment. Result The faucet s now actvated. Descrpton The faucet s nactve for 90 seconds. The faucet s actvated f t senses a hand presence. Ths s the default operatng mode of the faucet. The faucet wll shut off after 0 seconds regardless of hand presence detected. The faucet wll shut off 0 seconds after the detecton of the last hand presence. The faucet wll shut off 0 seconds after the detecton of the last hand presence. Change the detecton dstance of the nfrared sensor. The default sensor range s approxmately " beyond the spout. All settngs wll be reset to orgnal factory settngs. Mount shut-off screw Remove green adapter from holder 0 Attach cover. Faucet s ready to run through programmng sequence. Remove protectve coverng from sensor. Enablng Manual Settng Mode Operatng Modes A: Cleanng Mode B: Normal Mode Result The Wall Mount faucet s now mounted. Test Functon Mountng of SSPS Generator 9 Attach to supply. Attach nlet hose to supply and turn on water. Wth water on, check system for leaks. Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. The followng procedure (a, b, c) must be done three () tmes n a row. a - Rensert green adapter b - LED lghts up c - Remove green adapter mmedately after LED swtches off a B - Normal Mode c C - Meterng Mode 0 s D - Scrub Mode 0 s E - Scrub Mode 0 s b Legend: Water s off Water s on

5 CF HyTronc_SSPS_Install SSPS // 9: AM Page Ths faucet comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Plumber s Putty Adjustable Lockng Plers Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. Mountng of Deck Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. Do not tghten locknut before step s completed. Mount cover plate f requred. Plumber s putty s recommended to seal cover plate to the snk. Securty pn must be located on the left sde. Mountng of Wall Mount Faucet Supply valve s nstalled Water supply lnes are flushed properly It s not necessary to unscrew the connecton between braded hose and housng to nstall the product. Do not remove protectve coverng from sensor untl startng up faucet operaton. The SSPS Generator comes wth all the components needed for nstallaton, however, some tools and supples are not ncluded. Basn Wrench Hand Drll Adjustable Lockng Plers Fully open supply valve. Includes SSPS Generator Unt Electroncs Module and Holder Green Power Adapter Hose If the faucet does not work as descrbed below, see Troubleshootng secton Hold hand n front of sensor - Water flow starts. Aerator:.0 gpm (standard) and optonal 0. gpm nsert CARE AND MAINTENANCE A battery model s shown n the followng example. These nstructons apply to all models. After 0 mnutes, the "Manual Settng" mode wll be dsabled automatcally and all settngs wll be saved. Faucet Adjustments Operatng modes and sensor ranges can be adjusted wth a manual operaton through the nfrared sensor. A tradtonal lavatory faucet s shown as an example. Faucet adjustment operatons apply to all models. Alternatvely, operatng modes and sensor ranges can be adjusted wth a Commander Handheld Programmng Unt. For more nformaton, vst our webste at Water supply valve s open Mount gasket, put faucet nto openng and tghten Place nut onto mountng rod and tghten wth wrench. If faucet was nstalled wth cover plate, secure wth basn washer, flat washer and locknut. Install aerator and tghten wth aerator key (suppled). Aerator:.0 gpm (standard) and optonal 0. gpm nsert Result The Deck Mount faucet s now mounted. Insert green adapter OPERATING MODES Poston SSPS under snk. Carefully poston to allow connecton of water lnes and wrng. housng vertcally Warnng: Hot water may burn your skn. Hold hand carefully under water and remove quckly. Mark holes. Poston mountng bracket and mark mountng holes. C: Meterng Mode (0 s) D: Scrub Mode (0 s) Remove housng vertcally Mount housng vertcally E: Scrub Mode (0 s) F: Sensor Range Adjustment Connect wrng. Remove cover and connect faucet wre to SSPS and secure nto wre harness. G: Reset Mount gasket and put faucet nto snk. Mount bracket from underneath. Place hoses through large openng and mountng rod through small openng. Make sure flange sts securely aganst surface. Remove all tems from snk. Connect faucet to SSPS unt. Attached to faucet and nstall water supply lne. Install flter at ths pont. Install aerator and tghten wth aerator key (suppled) For gooseneck faucets, tghten spout wth wrench. Aerator:.0 gpm (standard) and optonal 0. gpm nsert Remove shut-off screw Result The faucet s now tested. In order to set the operatng modes, the faucet needs to be placed nto "Manual Settng" mode. At ths tme, operatng modes can be changed wthn the next 0 mnutes.the followng s a functonal dagram to show the dfferent settngs avalable for manual faucet adjustment. FUNCTION DIAGRAM OF OPERATING MODES Result The "Manual Settng" Mode s now enabled. Water pulses n seconds [s] Modes A - Cleanng Mode Drll holes. Drll holes for screw anchors. Secure SSPS to wall. Insert anchors nto holes and mount SSPS unt to wall wth suppled screws. Wat for seconds for faucet to calbrate to ts envronment. Result The faucet s now actvated. Descrpton The faucet s nactve for 90 seconds. The faucet s actvated f t senses a hand presence. Ths s the default operatng mode of the faucet. The faucet wll shut off after 0 seconds regardless of hand presence detected. The faucet wll shut off 0 seconds after the detecton of the last hand presence. The faucet wll shut off 0 seconds after the detecton of the last hand presence. Change the detecton dstance of the nfrared sensor. The default sensor range s approxmately " beyond the spout. All settngs wll be reset to orgnal factory settngs. Mount shut-off screw Remove green adapter from holder 0 Attach cover. Faucet s ready to run through programmng sequence. Remove protectve coverng from sensor. Enablng Manual Settng Mode Operatng Modes A: Cleanng Mode B: Normal Mode Result The Wall Mount faucet s now mounted. Test Functon Mountng of SSPS Generator 9 Attach to supply. Attach nlet hose to supply and turn on water. Wth water on, check system for leaks. Do not use ppe dope on faucet and supply connectons. Possble solenod contamnaton could occur and wll vod any warranty. The followng procedure (a, b, c) must be done three () tmes n a row. a - Rensert green adapter b - LED lghts up c - Remove green adapter mmedately after LED swtches off a B - Normal Mode c C - Meterng Mode 0 s D - Scrub Mode 0 s E - Scrub Mode 0 s b Legend: Water s off Water s on

6 Lmted Warranty The CHICAGO FAUCET COMPANY ( Chcago Faucets ) extends to the orgnal consumer the followng warrantes for Genune Chcago Faucets manufactured products and components, or other components under the Chcago Faucets Warrantes, (collectvely, the Products ). Lfetme Faucet Warranty The Faucet, defned as any metal cast, forged, stamped of formed porton of the Product, not ncludng electronc or movng parts or water restrctng components, or other components covered under the Chcago Faucet warrantes, s warranted aganst defects for the lfe of the product. One Year Fnsh Warranty The fnsh of the Product s warranted aganst manufacturng defects for a perod of one () year from the date of Product purchase. Electronc Faucets Mechancals Warranty Are warranted for fve () years from the date of nstallaton. Electronc Faucets Fnshes Warranty Are warranted for one-year from the date of nstallaton. Electronc Faucets Electroncs and Solenod Warranty Are warranted for three () years from the date of nstallaton. A - Settng Cleanng Mode Settng the cleanng mode wll make the faucet nactve for 90 seconds. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Fully cover sensor wth hand, untl water flow stops. (Ths takes seconds) Remove hand Result The Cleanng Mode s now actve. For the next 90 seconds, the faucet wll be nactve. B - Settng Normal Mode Settng the normal mode wll allow the faucet to actvate only when t senses a hand presence. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Fully cover sensor wth hand. Water flow stops after seconds - Contnue to hold on for one () addtonal water pulse Remove hand Result Normal Mode s now actvated. C - Settng Meterng Mode (0 seconds) Settng the meterng mode wll allow the faucet to actvate for a full 0 seconds after t senses a hand presence. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Fully cover sensor wth hand. Water flow stops after seconds - Contnue to hold on for another two () addtonal water pulses The Chcago Faucet Company 00 South Clearwater Drve Des Planes, IL 00 Phone: /0-000 Fax: /0- Techncal: 00/- Remove hand Result Meterng Mode s now actvated for 0 seconds. 0 Chcago Faucet Company /

7 D - Settng Scrub Mode (0 seconds) Settng the scrub mode for 0 seconds wll allow the faucet to actvate for 0 seconds from the last hand presence. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Fully cover sensor wth hand. Water flow stops after seconds - Contnue to hold on for another three () addtonal water pulses Remove hand Result Scrub Mode s now actvated for 0 seconds. E - Settng Scrub Mode (0 seconds) Settng scrub mode for 0 seconds wll allow the faucet to actvate for 0 seconds from the last hand presence. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Fully cover sensor wth hand. Water flow stops after seconds - Contnue to hold on for another () addtonal water pulses Remove hand Result Scrub Mode s now actvated for 0 seconds. The detecton dstance of the sensor can be adjusted between approxmately - nches from the nfrared wndow. Enable Manual Settng Mode > see Enablng Manual Settng Mode secton Remove all tems from snk Fully cover sensor wth hand. Water flow wll stop after seconds - Contnue to hold on for fve () addtonal water pulses Remove hand Hold hand n the current detecton area untl LED flashes. Then move hand to the desred detecton dstance. When LED stays lt for () seconds, detecton dstance has been re-set to new locaton. Result The detecton dstance s now calbrated. G - Reset All settngs wll be reset to default settng. The Manual Settng Mode wll be dsabled. The procedure for the reset s the same as Enablng Manual Settng Mode, but step needs to be done sx () tmes n a row. Result All settngs are reset to default settngs and the manual-settng-mode s now dsabled. EXPLANATION OF SYMBOLS Symbol Meanng WARNING Refers to a stuaton of potental danger thay may cause serous njury or death CAUTION Refers to a stuaton of potental danger thay may cause slght or medum njury or property damage Refers to mportant nformaton. CARE AND MAINTENANCE INSTRUCTIONS The followng nstructons are descrbed n ths secton: Actvatng Cleanng Mode Cleanng or Replacng Inlet Flter Cleanng or Replacng Outlet Actvatng Cleanng Mode In order to set the cleanng mode, the faucet needs to be have been set once nto the "Manual Settng" mode. See "Manual Settng" nstructons. When cleanng mode s actvated, the faucet wll be noperable for 90 seconds. Fully cover sensor wth hand, untl waterflow stops. (Ths wll take approxmately seconds) Remove hand Result Cleanng mode s now actvated.

8 TROUBLESHOOTING Problem: No Water Flow Possble Cause Supply valves are closed Aerator s blocked or drty Inlet water lne flter s drty or blocked Braded hose s knked No external water pressure Battery s draned Reverse green adapter nserton Connector between SSPS and power adapter unplugged Power adapter contacts are corroded Connectng cable s knked or broken Shut-off screw s mssng or defectve Solenod valve noperable Faucet s n cleanng mode Electroncs module noperable Green Power adapter defectve Contact Sensor dstance s not adjusted properly Infrared wndow scratched or drty Interferng reflectons from snk Soluton Open supply valves Clean or replace Outlet See "Care and Mantenance" Clean or replace flter See "Care and Mantenance" Elmnate braded hose knk Check water pressure Provde water pressure Replace SSPS unt Contact Chcago Faucets techncal servce or replace power adapter Insert green adapter correctly Plug connector (green plugs) Clean contacts Replace defectve parts at chcagofaucets.com Replace shut-off screw at chcagofaucets.com Replace solenod valve Wat for cleanng mode to end (appr. 90 seconds) Contact Chcago Faucets techncal servce or replace power adapter at chcagofaucets.com Chcago Faucets techncal servce or replace power adapter at chcagofaucets.com Reset sensor montorng range Remove and re-nstall shut-off screw. Do not dsturb sensor scannng procedure (wat untl water flow stops and LED swtches off) Clean wndow wth smooth cloth Reset montorng range Remove and renstall shut-off screw. Do not dsturb sensor scannng procedure (wat untl water flow stops and LED swtches off). Adjust upper and lower beam to compensate for reflectons (Commander Handheld Programng Unt requred. Go to commander for detals) TROUBLESHOOTING Problem: Water runs contnuously and stops when object present Possble Cause Soluton Connector between electroncs Plug connector properly module and solenod valve plug s reversed Problem: Water runs contnuously Possble Cause Soluton Interferng object s n Remove object from montorng montorng range area. Remove and re-nstall shut-off screw. Do not dsturb sensor scannng procedure (wat untl water flow stops and LED swtches off) Defectve electroncs module Replace electroncs module at chcagofaucets.com Improper electroncs module Change mode or reset sensor See "Care and Mantenance" External water pressure too hgh Check external water pressure Provde pressure between 0 - ps Solenod valve noperable Replace solenod valve at chcagofaucets.com Problem: Water flows although shut-off screw s removed Possble Cause Soluton Electroncs module s noperable Replace electroncs module at chcagofaucets.com Water drops on nfrared wndow Clean wndow wth smooth cloth Problem: Faucet turns on by tself Possble Cause Soluton Infrared wndow s drty or scratched Clean wndow wth smooth cloth Faucet s nfluenced by Reset montorng range room envronment Remove and re-nstall shut-off (mrror, stanless steel or screw. Do not dsturb sensor scannglass snk, etc.) ng procedure (wat untl water flow stops and LED swtches off) Adjust upper and lower beam to compensate for reflectons (Commander Handheld Programmng Unt requred. Go to " commander" for detals) Input lne pressure fluctuates Install approprate lne pressure regulators Problem: Faucet s leakng water Possble Cause Soluton Connectons between housng Check O-rngs and braded Replace O-rngs when damaged or mssng Connecton between braded hose Check rubber washers and nlet supply are loose Replace washers when damaged or mssng Connecton between valve body Check O-rngs - Replace O-rngs and solenod valve s loose when damaged. Carefully re-nstalled solenod valve & do not over tghten Faucet drps, solenod valve Clean or replace solenod valve does not close at chcagofaucets.com