36 Electric Modular Downdraft Cooktop

Transcription

1 MPORTANT: Read and save these instructions. MPORTANT: nstaer: Leave nstaation nstructions with the Homeowner. Homeowner: Keep nstaation nstructions for future reference. Save nstaation nstructtons for oca eectrca inspector s use. Part No O/ Eectric Moduar Downdraft Cooktop Rev. A

2 Before you start... Proper instaation is your responsibiity. A quaified technician shoud insta this downdraft cooktop. Make sure you have everything necessary for correct instaation. t 1s the responsibiity of the instaer to compy with the instaation cearances specified on the seria/rating pate. The seria/rating pate is ocated on the rear wa of the burner box. FOR PRODUCT DMENSONS see Pane C. 18 mn. cearance urmer cabn o NOTE: 24 min. when bottom 01~ wywydrteta cabnei k ii me retar %b n mboard ess than M covered wh not ess than No. 28 MSG sheet stee daness dea, auminum of copper. 30 mn. ceamnce between the top of the cooking piatiorm and the bottom of an unpmtecied See NOTE for mnmum cearances. wood or meta cabinet. Panes A and B. Check ocation where downdraft cooktop wi be instaed. The ocation shoud be away from strong draft areas, such as windows or doors or strong heating vents and fans. Before making countertop cutout, check that ductwork and cooktop ocation wi cear cabinet was, backspash and rear wa studs inside cabinet. 2 mn. o backspash rear pea of wa / mportant: Observe a governng codes and ordinances. removed and the drawer fronts instaed Countertop opening dimensions that are shown must be used. Given dimensions provide 0 cearance. ALL OPENNGS N THE WALL OR FLOOR WHERE DOWNDRAFT COOK-TOP S TO BE NSTALLED MUST BE SEALED. Fire Hazard Do Not obstruct the fow of combustion and ventiation air. Persona njury Hazard Avoid instaing cabinet storage above the cooking surface. tf cabinets are aready instaed, avoid the use of cabinet whie cooktop is in US. Reaching over a heated cooking surface coud resut in a serious burn or other persona injury. t is the customer s responsibiity: To contact a quaified eectrica instaer. To assure that eectrica instaation is adequate and in conformance with Nationa Eectrica Code, ANSJNFPA 70 - atest edition*, and a oca codes and ordinances. Take specia care when driing hoes into wa for venting. Eectrica wires may be conceaed behind wa covering. Do Not use this appiance with any soid state fan speed contro device. Faiure to do so coud resut in fire, eectrica shock or other persona injury. Mobie home instaation The instaation of this cooktop must conform to the Manufactured Home Construction and Safety Standards, Tite 24 CFR, Part 3280 (formery the Federa Standard for Mobie Home Construction and Safety, Tie 24, HUD Part 280) or when such standard is not appicabe. the Standard for Manufactured Home nstaation 1982 (Manufactured Home Sites, Communtties and Setups), ANS A or atest edition, or with oca codes. Copies of the standards isted above may be obtained from: Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts Toos needed for instaation: - // meta snips ducttape Pipe wrench or knife Eectrica requirements MPORTANT: Save nstaation nstructions for eectrica ins0ector s use. L Eectrica ground is required on this appiance.. f cod water pipe is interrupted by pastic, non-metaic gaskets or other insuating materias, Do Not use for grounding.. Do Not ground to a gas pipe. Do Not have a fuse in the neutra or grounding circuit. A fuse in the neutra or grounding circuit coud resut in eectrfca shock. Check with a quatttied eectrician if you are in doubt as to whether the appiance is propery grounded. Faiure to foow these instructions coud resut in serious injury or death. f oca codes permit and a separate grounding wire is used, it is recommended that a quaifred grounding eectrician determine that the path is adequate. Parts supped for itnstaatgon: E n Hod-down screws are attached. Pane A A n A three-wire or four-wire, singephase, 120/240-vot, &Hz, AC-ony eectrica suppy (or three-wire or fourwire, 120/208-vot if specified on the seria/rating pate) is required on a separate 40-ampere circuit, fused on both sides of the ine. A time-deay fuse or circuit breaker is recommended. The fuse size must not exceed the circuit rating of the appiance as specified on the seria/rating pate is ocated pate. The seria/rating on the rear wa of the burner box. B w DOWNDRAFT COOK-TOP MUST BE CONNECTED WTH COPPER WRE ONLY. DO NOT USE ALUMNUM WRE. C n Wire sizes and connections must conform to the requirements of the Nationa Eectrica Code, ANS/NFPA 70 - atest edition*, and a oca codes and ordinances. Wire sizes and connections must conform with the rating of the appiance. Copies of the standards isted may be obtained from: Nationa Fire Protection Association Batterymarch Park Quincy, Massachusetts D n The fexibe armored cabe extending from the appiance shoud be connected directy to the junction box. The appiance shoud be connected to the fused disconnect (or circuit breaker) box through fexibe armored or non-metaic sheathed copper cabe. Locate the junction box to aow as much sack in the ine as possibe between the junction box and appiance so that the downdraft cooktop can be moved if servicing is ever necessary. F n A U.L.-isted /2 conduit connector must be provided at the junction box. G w A wiring diagram is ocated beow the contro mounting pate.

3 Eectrica connectjron junctton box \ cabe from power suppy J white wires requirements Ductwork needed for instaation incuded. is not Eectrica ground -S required on this appiance. Do Not connect to the eectrica suppy unti appiance is permanenty grounded. Disconnect power to the junction box before making the eectrica connection. This appiance must be connected to a grounded, metaic, permanent wiring system, or a grounding connector shoud be connected to the grounding termina or wire ead on the appiance. Faiure to do so coud resut in a fire, persona injury or eectrica shock. This appiance is manufactured with a white (neutra) power suppy wire and a frame-connected green (or bare) grounding wire twisted together. Connect the appiance cabe to the junction box through the U.L.-isted conduit connector. Compete eectrica connection according to oca codes and ordinances. A n connecting conductor box wire: Where oca codes permit... the frame-grounding to the neutra (white) junction 1. Disconnect the power suppy. 2. Connect the fexibe armored cabe U.L.-isted conduit connector. Tighten 3. Connect the neutra (white) wire in the junction box with the green (or bare) wire and white wire from the appiance cabe with a wire connector. 4. Connect the two back wires together; then connect the two red wires together with wire connectors, (See Figure 1.) cabe from power suppy junction box J back wire bare) wires /+ cabe from cooktop. &-isted conduit connector Ungrounded neutra Figure 2 4. Connect the white wire from the power suppy cabe to the neutra (white) wire in the junction box. 5. Connect the two back wires together; then connect the red wires together with wire connectors. (See Figure 2.) 6. Connect the green (or bare) wire to a grounded cod water pipe* (or to?he grounded ead in the service pane). Do Not ground to a gas suppy pipe or hot wafer pipe. Do Not connect to eectrica suppy unti appiance is permanenty grounded. (See Figure 3.) grounded cod water pipe GROUNDED CLAMP MUST BE TGHT ON PPE.. Tghren n tits firmy. \ CODDW grdinding / :+T m PiF / be wire No.-4 copper camps Figure 3. Grounded cod water pipe must have meta continuity to eectrica ground and not be interrupted by pastic, rubber, or other eectrcay insuating connectors, such as hoses, fittings, washers or gaskets (incuding water meter or pump). Any eectrica insuating connector shoud be jumped as shown with a en th of No-4 wre securey camped to bare me 3 a at both ends. wire Fire Hazard. Venting system MUST terminate to the outside. Do Not terminate the ductwork in an attic or other encosed space. Do Not use 4 aundry-type wa caps. Do Not use pastic-type ductwork. Faiure to foow recommended venting instructions may resut in a fire. Determine which venting method to use. Ductwork can extend either through the wa or foor. The ength of the ductwork and number of ebows shoud be kept to a minimum to provide efficient performance. The size of the ductwork shoud be uniform. Do Not insta two ebows together. Use duct tape to sea a joints in the ductwork system. Use cauking tape to sea the exterior wa or foor opening around the cap. Do Not cut joist or stud. f ductwork cutout fas over a joist or stud, a supporting frame must be constructed. Fexibe meta ductwork is Not recommended. f it is used, cacuate each foot of fexibe ductwork as two feet of rigid. Fexibe ebows count twice as much as standard ebows. Use meta ductwork ony. Figures 5-8 show common venting methods and types of materias needed. NOTE: Make sure there is proper cearance within the wa or foor exhaust duct before making cutouts. Recommended duct ength Ductwork ength shoud not exceed the maximum ength isted in the Maximum ength of duct system chart. (See Pane C.) Through the wa instaation Outside wai ocaton housing bare) wire B n cabe-tram cooktop twist-on U.i.-ist@ conduit Grounded neutra Figure 1 Where oca codes Do Not permit... connecting the frame- grounding conductor to the neutra (white) junction box wire: 1. Disconnect the power suppy. 2. Connect the fexibe armored cabe U.L.-isted conduit connector. Tighten 3. Separate the white wire from the green (or bare) wire that extends out the end of the appiance cabe. (See Figure 2.) Pane B con/nectar C m f connecting to a four-wire eectrica system: 1. Disconnect the power suppy. 2. Connect the fexibe armored cabe U.L.-isted conduit connector. Tighten 3. Separate the white wire from the green (or bare) wire that extends out the end of the appiance cabe. (See figure 4.) 4. Connect the white wires together; connect the red wires together; then connect the back wires together with wire connectors. 5. Connect the green (or bare) grounding wire from the appiance cabe to a grounding wire in the junction box. junction box reen (or &Y re) wires A cabe from c&ktop cabe tram power suppy d Figure 4 connector white wires back wire Figure 5 Figure 6 Through the foor instaation isand ocation 4 Figure 7

4 ..._ haust vent rom centerine of vent to front edge of cutout Now start... 5 n Connect vent adapter to instaed venting system. See Venting requirements, Panes B and C. 6 Make eectrica connections. n See Eectrica requirements and Eectrica connection sections, Panes A and B. Figure 8 Recommended duct ength for isand or peninsua instaations Use round 6 or 3-/4 x 10 duct with a maximum of 26 feet for duct system. For best performance, use no more than three 90 ebows. Do Not insta two ebows together. Determining you need. the ength of system To cacuate the ength of system you need, add the equivaent feet for each duct piece that wi be needed. See the foowing exampes. 6 duct system (3JjFj 90 ebows Maximum ength = 26 ft ebows 1 -surface wa cap = oft. = Oft. 8 feet straight = 8ft. Length of 6 system = 18ft. Recommended standard finings 6 systems: equivaent ength of 6 duct 3-/4 x 10 to 3-y/4 x o to 6 6 to x 10 6 = 4.5 ft. 900 mow = 5 ft. 9o ebow=9ft. Cut meta band from around, the top fange of carton and remove the top of carton. Fiters ocated here. 2 Remove the foam pads and. cooktop from carton. Remove foam pads from front and back of cooktop. Remove any tape from cooktop, incuding tape hoding fiters inside the appiance. 3 nsta venting adapter to bower w housing using three screws provided. Rotate the bower housing downward to cear the cabinet opening. 4 hod-down bot nsert the downdraft cooktop into the countertop cutout. n Check that front edge of downdraft cooktop is parae to front edge of countertop and at east 1- /2 inches back from front edge of countertop and 2 inches from any vertica was. Tighten hod-down bots a-t each side of unit. 7 nsta modues in cooktop w foowing instructions in Use and Care Guide. Turn power suppy on. Check 8. that gri, modue and vents are operating correcty. f one does not operate, disconnect the power source and check that wire connections have been made correcty. your new Whirpoo downdraft cooktop. To get the most efficient use from your new downdraft cooktop, read your Whirpoo Use and Care Guide. 1 Congratuations! 1 Keep nstaation nstructions and Guide cose to downdraft cooktop for easy reference. The instructions wi make reinstaing 3-/4 x 10 duct system & $ &W 0 k-6ft.- 6 to3-/&x 10 transition k m ength = 20 ft ebow = 5ft. 1 - wa cap = Oft. 1-6 to 3- /4 x 10 transition = 6ft. 8 feet straight = 8f-t. Length of 3- /4 x 10 system = 19ft. Recommended standard fittings systems: equivaent ength d x 10 duct Numbers correspond to steps. 6 to 3-/4 x 10 6 to 3-/4 x 10 9o ebow =9ft. = i n x o fat ebow = 12 tt. 3-/Cx cap=ofi. o wa Pane C

5 f the downdraft cooktop does not operate... Check that the circuit breaker is not tripped or the house fuse bown. See Use and Care Guide for troubeshooting checkist. NOTE: Refer t& Use and care GJ~&~ and ceaning f you need assistance... The Whirpoo Consumer Assistance Center wi answer any questions about operating or maintaining your cooktop not covered in the nstaation nstructions. The Whirpoo Consumer Assistance Center is open 24 hours a day, 7 days a week. Just dia - (800) the ca is free. When you ca, you wi need the cooktop mode number and seria number. Both numbers can be found on the seria/rating pate occrted on the rear wa of the burner box. f you need servke... n the event that your Whirpoo appiance shoud need service, ca the deaer from whom you purchased the appiance or a Whirpoo-authorized service company. A Whirpooauthorized service company is isted in the Yeow Pages of your teephone directory under Appiances - Househod - Major - Service or Repair. You can aso obtain the service company s name and teephone number by diaing, free, within the continenta United States, the Whirpoo Consumer Assistance Center teephone number, -(800) A specia operator wi te you the name and number of your nearest Whirpoo- authorized service company. Maintain the quaity buit into your Whirpoo appiance--ca a Whirpooauthorized service company. Vkff 01 C- 4a Prnted on recyced paper. 10% post consumer waste/ 50% recovered materias. Part No O/ Rev. A Whirpoo Corporation Prepared by Whirpoo Corporation, Benton Harbor, Michigan Prnted n U.S.A.