MANUAL DE INSTALACIÓN

Transcription

1 MANUAL DE INSTALACIÓN Spit Duct Air Conditioner Digita Scro and DC Inverter Commercia Air-conditioner The Digita Scro and DC Inverter share the same indoor units. Thank you very much for purchasing our air conditioner, pease read this manua carefuy and keep it for future reference.

2 CTENTS PAGE Disconnect the power suppy before ceaning and maintenance. Indoor Unit Enough room for instaation and maintenance. The ceiing is horizonta and it can afford the weight of the indoor unit. The air inet and outet are not impeded and does not affected by outdoor air too much. The air fow can reach every part of the room. The connecting pipe and drainpipe can be easiy extracted out. There is no direct radiation from heat source. Outdoor Unit Enough room for instaation and maintenance. The air inet and outet are not impeded and does not affected by outdoor air too much. Dry and we ventiated pace. To insta propery, pease read this manua at first. The air conditioner must be instaed by quaified persons. When instaing the indoor unit or its tubing, pease foow this manua as stricty as possibe. When a the instaation work is finished, pease turn on the power ony after a thorough check. No further announcement if there is any change of this manua caused by product improvement. NOTE The instaor shoud iustrate to users how to correcty use and maintain the air-conditioner, as we as remind users to carefuy read and keep both Instaation Manua and Owner's Manua we. DISPOSAL:Do not dispose this product as unsorted municipa waste. Coection of such waste separatey for specia treatment is necessary. The supporter is fat and horizonta and can afford the weigh of outdoor unit, without noise and vibration. The noise and the outet air wi not infuence your neighbor. No combustibe gas. Pace convenient for piping and wiring. Pease keep away from the foowing paces, or mafunction may be caused.(if unavoidabe, pease consut the professionas): There is minera oi ike the oi of cutting machine. There is much saty air. (Near the coast) There is caustic gas such as sufuric gas. (Near the hotspring.) Factory where the votage fuctuate greaty. In the car or in the cabin. In the kitchen or a pace fu of oi steam. There is strong eectromagnetic wave. There is combustibe gas or materias. There is much evaporating acid or akaine gas. Other specia areas. Notes Before Instaation This appiance is not intended for use by persons (incuding chidren) with reduced physica, sensory or menta capabiities, or ack of esperience and knowedge,uness they have been given supervision or instruction concerning use of the appiance by a person responsibe for their safety. Chidren shoud be supervised to ensure that they do not pay with the appiance. Seect the correct carry-in path. Move this unit as originay packaged as possibe. If the air conditioner is instaed on a meta part of the buiding, it must be eectricay insuated according to the reevant standards to eectrica appiances. instaation manua

3 NOTE Remark per EMC Directive 89/336/EEC Mounting screw For to prevent ficker impressions during the start of the compressor (technica process), foowing instaation conditions appy. The power connection for the air conditioner has to be done at the main power distribution.the distribution has to be of a ow impedance, normay the required impedance reaches at a 32A fusing point. No other equipment has to be connected with this power ine. For detaied instaation acceptance, pease refer to your contract with the power suppier if restrictions do appy for products ike washing m achines, air con ditioners or eectrica ovens. For power detais of the air conditioner, refer to the rating pate of the product. For any question contact your oca deaer. Tabe.3- Name of Accessories Instaation manua Wire controer Q ty 4 Outine The foowing are seectabe accessories 2 Remote controer & Its Frame. Remote controer... Usage Wire contro the air-conditioner Remote controer Cautions on remote controer instaation Never throw or beat the controer. Before instaation, operate the remote controer to determine its ocation in a reception range. Keep the remote controer at east m apart from the nearest TV set or stereo equipment. (It is necessary to prevent image disturbances or noise interferences.) Do not insta the remote controer in a pace exposed to direct sunight or cose to a heatingsource, such as a stove. Note that the positive and negative poes are in right positions when oading batteries. Instaing Φ0 Hanging Screw Bots (4 Bots) Pease refer to the foowing figure for measurement between the screw bots. Pease insta with screw bots. the distance The handing to the ceiing varies from the constructions, consut the construction personnes for the specific procedures. The size of the ceiing to be handed.do keep the ceiing fat. Consoidate the roof beam for possibe vibration. Cut off the roof beam. Strengthen the pace cut off, and consoidate the roof beam. Carry out the pipe and ine operation in the ceiing after finishing the instaation of the main body. Whie choosing where to start the operation, determine the direction of the pipes to be drawn out. Especiay in case there is a ceiing, position the refrigerant pipes, drain pipes, indoor & outdoor ines to the connection paces before hanging up the machine. The instaation of hanging screw bots. Wooden construction Remote controer hoder Fig.3- Put the square timber traversey overthe roof beam, then insta the hanging screw bots. (Refer to Fig.4-) Timber over the beam 2. Remote controer hoder Mounting screw (ST2.9x0-C-H)...2 Roof beam Ceiing Hanging screw bots Fig.4- New concrete bricks Inaying or embedding the screw bots (Refer to Fig.4-2) 4. Akaine dry battery(am4)...2 Bade shape insertion Side insertion Fig.4-2 instaation manua

4 For origina concrete bricks Use embeding screw bod, crock and stick harmness (refer to Fig.4-3) Stee bar Embedding screw bot (Pipe hanging and embedding screw bot) Fig.4-3 Stee roof beam structre Insta and use directy the supporting ange stee. (refer to Fig.4-4) Fig.4-6 Hanging screw bot Hanging bots Supporting ange stee Fig.4-4 Overhanging the indoor unit Overhang the indoor unit onto the hanging screw bots with bock. Position the indoor unit in a fat eve by using the eve indicator, uness it may cause eakage. Screw nut Fig.4-7 washer Hanging screw bot Overhang part Fig.4-5 Insta the main body Instaing the dust proof net and canvas air passage Open the air-in gri Anti-cockwise the bots as indicated in foow figure sketch.then pu down the air-in gri. Take out the air-in gri. Dismante the air fiter Cean the air fiter (Vacuum ceaner or pure water may be used to cean the air fiter. If the dust accumuation is too heavy, pease use soft brush and mid detergent to cean it and dry out in coo pace). The air-in side shoud face down when using water. (See Fig.4-7) Pipe Connection 2 Fig.4-8 The static pressure outside the unit is 200Pa, the ength of the air pipe attached is determined by this parameter. The positioning of ceiing hoe and indoor unit and hanging screw bots Routine method of instaation: the size of instaation for indoor unit foowing Fig.4-9 Pease insta with Φ0 hanging screw bots. 6 The air-in side shoud face up when using vacuum ceaner. (See Fig.4-8) 3 Carry out the pipe and ine operation in the ceiing after finishing the instaation of the main body. Whie choosing where to start the operation, determine the direction of the position the refrigerant pipes, drain pipes, indoor & outdoor ines and inecontroed ines to the connection paces before. instaation manua

5 The positioning of ceiing hoe and indoor unit and hanging screw bots routine method of instaation: the size of instaation for indoor unit foowing the Fig.4--9 and Fig.4-0 Unit: mm 7.~.2KW/h Fig.4-9 4~6KW/h Unit: mm 43 6 Fig.4-0 instaation manua

6 The method of instaation: Adopt foowing method if the air-conditioning s size of instaationsite is imited and the indoor unit can t put into the instationsite. 7.~.2KW/h Fig.4-. The whoe unit status show as Fig.4-2. Remove the a from fixed Safety Drain Tray, and then take off the tray as figure showed in Fig Take off the tray aong the direction of the arrow show in Fig Cean the tray and evaporator. 5. Re-insta the unit foow the reverse above orders. Fig.4-2 CAUTI. Pease shut down the unit and cut off power cabe before maintain the motor. 2. Don t heavy pu the foam tray, when dismounting; otherwise the foam tray woud break. instaation manua

7 maintenance of motor: Fig.4-3 Inside of structure Front view of fan assemby instaation state Side view of fan assemby instaation state Fan assemby shoud push horizontay to the end (about 8mm), and then take o f f it. The state after fan assemby is taken off Fig.4-4. Refer to Fig.4-3, remove a bots from safety drain tra y, and take o f f the safety drain tra y. 2. Refer to Fig.4-3, remove a 4 bots from reinforced pane, and take o f f the pane. 3. Refer to Fig.4-3, remove a 4 bots from fan assemby, see Fig.4-4, accor ding to which orders to take off the fan assemby. 4. Refer to Fig.4-4, horizonta pushing the fan assemb y, unti it cannot not move any furthe r, and then ift up sighty and take down to remove it. 5. After motor maintenance, reinsta the fan assembies as per the reverse above orders. And connect the motor with eectric contro box, as motor with power cabe of capacit y. CA U TI. Pease shut down the unit and cut o f f power cab e before maintain the moto r. 2. Before dismount the fan assemb y, you must remove the motor and eectric contro box, as we a s connective wires between motor and capacity assemb y. 3. Fan subassemby is very heav y, pease be carefu during maintaining, otherwise physica injury woud be caused. instaation manua

8 4~6kw/h Fig.4-5 Fig.4-6. The whoe unit status show as Fig Remove the a from fixed Safety Drain T ra y, and then take o f f the tray as figure showed in Fig T ake o f f the tray aong the direction of the arrow show in Fig Cean the tray and evaporato r. 5. Re-insta the unit foow the reverse above orders. CAUTI. Pease shut down the unit and cut o f f power cabe before maintain the moto r. 2. Don t heavy pu the foam tra y, when dismounting; otherwise the foam tray woud break. instaation manua

9 maintenance of motor: Fig.4-7 Inside of structure Side view of fan assemby instaation state Front view of fan assemby instaation state Fan assemby shoud push horizontay to the end (about 8mm), and then take o f f it. The state after fan assemby is taken off Fig.4-8. Refer to Fig.4-7, remove a from safety drain tra y, and take o f f the safety drain tra y. 3. Refer to Fig.4-7, remove a 4 bots from fan assemby, see Fig.4-8, accor ding to which orders to take off the fan assemby. 3. Refer to Fig.4-8, horizonta pushing the fan assemb y, unti it cannot not move any furthe r, and then ift up sighty and take down to remove it. 4. After motor maintenance, reinsta the fan assembies as per the reverse a bove orders. And connect the motor with eectric contro box, a s we as motor with power cabe of capacity. CAUTI. Pease shut down the unit and cut o f f power cabe before maintain the moto r. 2. Before dismount the fan assemb y, you must remove the motor and eectric contro box, as we as connective wires between motor and capacity assemb y. 3. Fan subassemby is very heav y, pease be carefu during maintaining, otherwise physica injury woud be caused. instaation manua

10 20KW/h 25KW/h 28KW/h 2 75 Entrances and exits for communication ines of indoor and outdoor 4-2*25 obong suspention bot hoes Air outet Eectrica parts box 4-Φ0 hanging screw (configure on spot) Air outet duct fange Refrigerant-pipe fared connectionφ9.52(3/8) Air intake duct fange Connecting point of drain pipe Refrigerant-pipe fared connectionφ6(5/8) Air intake Fig.4-9 The method of instaation: adopt foowing method if the air-conditioning s size of instaation site is imited and the indoor unit can t put into the instaation site. Fig.4-20 screw cover pate B cover pate A Part A of indoor unit A A bot C Part B of indoor unit B bot A C Fig.4-2 instaation manua

11 The indoor unit show as Fig.4-20 Foowing Fig.4-2 twist-off the screws, aong the direction of A get off the cover pate A and cover pate B. Dismounting bot A Dismounting bot C Aong the direction of B and C divided the part B and part C of indoor unit. The part A and part B of indoor unit individua put into the positionsite, then insta the indoor unit foowing the reverse order of step 2,3,4 and 5. Maintenance of motor NOTE During teardown and instaation, the scro was aowed direct support by hand Fan subassemby is more weightiness, pease take carefu during teardown and instaation, and keep from hurt by fan subassemby. Confirm that there is enough room for instaation and maintenance. Maintenance roomage bot Maintenance roomage motor assemby 600mmX600mm checking orifice Fig.5- bottom cover pate screw Confirm the minimum drain tit is /00 or more checking orifice pothook Fig.5-2 scro Fig.4-2 Cover the pipe before connecting to keep rubbish, dust or other impurities out. Tabe.6- Piping materia Copper specia for air conditioner 2 As figure dismounting the bot of bottom,get down the bottom cover pate. As figure dismounting 6 bots in the front pate. Capaticy(KW) Gas side Piping Liquid side 7./8/9/.2/4/6/20/25/28 Φ6 Φ Support the fan subassemby from the bottom, then itter up, get down fan subassemby. 4 After finished maintenance of motor, then insta the motor assemby in the reverse order of step,2 and 3. 5 During this process,the indoor unit don t need dismounted. instaation manua

12 Cover the pipe before connecting to keep rubbish, dust or other impurities out. As there is no dust fiter on the indoor unit, other paces which are easy to maintaining such as inhaant duct shoud be instaed with dust fiter. (Without dust fiter, dust adherent on the air heat exchanger may cause faiure and water-eak. Key points of duct connection Canvas tie-in Canvas tie-in Isoation booth Low speed Air outet Isoation booth Air inet Air dust fiter Fig.7- NOTE Other assembies shoud be prepared on spot except air conditioner main body. High Static Pressure Type Low speed Q(m 3 /h) Low speed instaation manua

13 High speed Low speed High speed Low speed Fig.7-7 Fig.7- High speed Low speed Heating capacity and cooing capacity are tested under the standard aowabe min. static pressure; the 7 test static pressure is 25Pa, 80/90/2 test static pressure is 37Pa, 40/60 test static pressure is 50Pa. Appicabe scope of static pressure 00~96Pa 00~96Pa 00~96Pa 75~50Pa 0~220Pa Fig.7-8 Pane instaation High speed Unoad inner frame. Side the knob, reease the bucke from the outside frame hoe, then unoad the inner frame. Inside frame Knob Bucke Outside frame Fig.7-2 Fig.7-9 Hang the outside frame on the main body with face down. (4 paces at 4 corners). Hang the bet on the hook of the main body. High speed Low speed Fig.7-3 Fig.7-0 Fig.7-4 instaation manua

14 NOTE The signa wire of the remote contro receiver must be drawn out through the canvas air passage. Fix the outside frame and the canvas air passage with screws. Screw must be fixed on from the bottom to the top. Insta remote controer. NOTE Connect the remote contro receiver with the indoor unit signa wires and fix it. Canvas air passage Fig.7-5 Hang up the outside frame unti it sticks to the ceiing tighty. Canvas air passage Check whether the height drop between the indoor unit and outdoor unit, the ength of refrigerant pipe, and the number of the bends meet the foowing requirements: The max height drop and The ength of refrigerant pipe deponding on the ouotdoor unit.(if the height drop is more than 0m, you had better put the outdoor unit over above the indoor unit.) The number bends fewer than 5. 2 Fig.7-6 Fix the main body and the outside frame with the fix board of waist-shape hoe (in two paces). Hang one side of the fix board of the waist-shaped hoe on the hook of the main body. Tighten the other side of the board with screw to the outside frame. Do not et air, dust, or other impurities fa in the pipe system during the time of instaation. The connecting pipe shoud not be instaed unti the indoor and outdoor units have been fixed aready. Keep the connecting pipe dry, and do not et moisture in during instaation. The Procedure of Connecting Pipes Measure the necessary ength of the connecting pipe, and make it by the foowing way. 3 Cut off the surpus part of the board with piers. Connect the indoor unit at first, then the outdoor unit. 4 Bend the top of the broken end. Bend the tubing in proper way. Don,t harm them. NOTE When hanging up the o utside frame with the fix board of waist-shaped hoe and the bet, stick the outside frame tighty to the ceiing and fix it. Fig.7-7 Insta the inner frame on the outside frame (the inverse sequence of unoading the inner frame). 2 3 Daub the surfaces of the fare pipe and the joint nuts with frozen oi, and wrench it for 3~4rounds with hands before fasten the fare nuts. (Refer to Fig.8-) Be sure to use two wrenches simutaneousy when you connect or disconnect the pipes. The stop vave of the outdoor unit shoud be cosed absoutey (as origina state). Every time you connect it, first oosen the nuts at the part of stop vave, then connect the fare pipe immediatey (in 5 minutes). If the nuts have been oosened for a ong time, dusts and other impurities may enter the pipe system and may cause mafunction ater. So pease expe the air out of the pipe with refrigerant before connection. Expe the air (refer to the Expe The Air ) after connecting the refrigerant pipe with the indoor unit and the outdoor unit.then fasten the nuts at the repair-points. Notices For Benabe pipe. The bending ange shoud not exceed 90 Bending position is preferaby in the bendabe pipe. The arger the better it is. Do not bend the pipe more than three times. Bend the connecting pipe of sma wa thickness. Fig.7-8 Cut out a desired concave at the bending part of the insuating pipe. instaation manua

15 Then expose the pipe(cover it with tapes after bending). To prevent coapsing of deforming, pease bend the pipe at its biggest radius. Use bender to get a sma radius pipes. Use the market brass pipe. Be sure to use the same insuating materias when you buy the brass pipe. (More than 9mm thick) Use frozen oi 90 ean crude burr Fig.9- Fig.8- Check a the joints with the eak detector or soap water. (See Fig.9-6 as a reference iustration) Bend the pipe with thumb Check-point of indoor unit D C Fig.8-2 Make the ends straight Check-point of outdoor unit B A Fig.8-3 Locate The Pipe Dri a hoe in the wa (suitabe just for the size of the wa conduit, 90mm in genera), then set on the fittings such as the wa conduit and its cover. Bind the connecting pipe and the cabes together tighty with binding tapes. Do not et air in, which wi cause water eakage by condensation. Pass the bound connecting pipe through the wa conduit from outside. Be carefu of the pipe a ocation to do no damage to the tubing. A. Lo-stop vave B. Hi-stop vave C,D. Joints of the connecting pipe to the indoor unit. Be sure to with insuating materias cover a the exposed parts of the fare pipe joints and refrigerant pipe on the iquid-side and the gas-side. Ensure that there is no gap between them. Incompete insuation may cause water condensation. Fig.9-2 Connect the pipes. Then, open the stem of stop vaves of the outdoor unit to make the refrigerant pipe connecting the indoor unit with the outdoor unit fuenty fow. Fig.9-3 Be sure of no eakage by checking it with eak detector or soap water. Cover the joint of the connecting pipe to the indoor unit with the sound proof/insuating sheath (fittings), and bind it we with the tapes to prevent eakage. Fig.9-4 instaation manua

16 Tabe.9-2 Tubing size Φ6.4mm Φ9.5mm Φ2.7mm Φ5.9mm Φ9.mm Torque 4.4~7.2N.m 32.7~39.9N.m 49.5~60.3N.m 6.8~75.4N.m 92.7~8.6N.m Manifod vave Muti-meter Pressure meter -76 cmhg Hi-ever Lo-ever Charge hose Charge hose Vacuum pump Lo-ever Fig.9-5 Fig.9-4 Tabe.9-2. Fig.9-6 Fare nut Stopper Cap Vave body Vave stem Fig.9-6 Fig.9-4 Insta indoor unit drain pipe The outet has PTI screw bread, For 7T to 60T indoor unit,pease use seaing materias and pipe sheath (fitting) when connecting PVC pipes. For 200T to 280T indoor unit,pease use Water connecting pipe when connecting drain pipes. CAUTI The drain pipe of indoor unit must be heat insuated, or it wi condense dew, as we as the connections of the indoor unit. Hard PVC binder must be used for pipe connection, and make sure there is no eakage. With the connection part to the indoor unit, pease be noted not to impose pressure on the side of indoor unit pipes. When the decivity of the drain pipe downwards is over /00, there shoud not be any win ding. The tota ength of the drain pipe when pued out traversey sha not exceed 20m, when the pipe is over ong, a prop stand must be instaed to prevent winding. Refer to the figures on the right for the instaation of the pipes..5m~2m Bend Fig.0- S shap instaation manua

17 Caution: Whie connecting the drain pipe, pease use the drain pipe connect to the secondary water hoder simutaneousy, for avoiding there are itte condensate water deposit in the unit when the machine is running under the high humidity working condition. CENTRAL CTROL MITOR 2 COMPUTER Attaching wiring The air conditioner shoud use separate power suppy with rated votage. The externa power suppy to the air conditioner shoud have ground wiring, which is inked to the ground wiring of the indoor and outdoor unit. The wiring work shoud be done by quaified persons according to circuit drawing. A eakage protector shoud be instaed according to the Nationa Standard concerning eectrica appiance. 2 Be sure to ocate the power wiring and the signa wring we to avoid cross-disturbance and their contact with connecting pipe or stop vaue body. The wiring attached to this air conditioner is 0m ong. Be sure to proong it with wiring of the same type and proper ength if necessary. Generay, do not twist two wiring together uness the joint is sodered we and covered with insuator tape. Do not turn on the power unti you have checked carefuy after wiring. The Specification of Power Tabe.- Power Capacity(KW) 7/80/90/2/40/60 200/250/280 Phase Frequency and vot -Phase CAUTI The reserved function is indicated in broken ine tabe,users can seect it when necessary. termina board wiring is different according to the horsepower of air-condictioners. The wiring of 7T to 60T indoor unit, pease refer to Fig.-3, and Fig.-4 is the wiring for 200T, 250T and 280T indoor unit. Circuit breaker/fuse (A) Indoor unit power wiring (mm 2 ) 0/0 2.5(<20 m)-4.0(<50 m) 6/ (<200 m) CAUTI A disconnection device having an air gap contact separation in a active conductors shoud be incorporated in the fixed wiring according to the Nationa Wiring Reguation. Communication wiring wi be different according to the horsepower of air-condictioners. The wiring of 7T to 60T indoor unit, pease refer to Fig.-, and Fig.-2 is the communication wiring for 200T, 250T and 280T indoor unit. instaation manua

18 Network Address Setting When V4+ outdoor unit set the code to be found address automaticay, the new V4+ indoor unit do not need to set the indoor unit address, at this time the V4+ outdoor unit wi distribute different addresses for indoor units automaticay. When V4+ outdoor unit set the code to be found address non-automaticay, a the indoor units must set the system addresses by remote controer first (For the setting system address of indoor unit which has two or more main boards, it has to separate use the dispay board connected with tencore connecting wire to set the address for each mainboard). The setting of network address is through the communication of indoor and outdoor units, its address is the same as the indoor unit system address, and not need to set separate. Base on different purposes to set the switch codes on the main boards of indoor unit, Once finish the setting, pease cut off the main power, and then switch on the power again. Otherwise, setting functions coud not work. ENC When a indoor units are V4+ series indoor unit, the centra controing of indoor unit can be finished in the outdoor unit, and not need to make centra contro in the indoor unit, the detai pease refers to the V4+ outdoor unit instruction manua;. For the previous indoor unit s centra contro function, can use (X, Y, E) termina to connect and form the centra contro group, at this time there is not need to set the network address, and aso can use outside setting network modue, mainboard (CN20) to form network. Tabe.2- ENC Togge switch Code For set horsepower Capacity(Horsepower) 2200W(0.8HP) 2800W(.0HP) 3600W(.2HP) 4500W(.5HP) 5600W(2.0HP) 700W(2.5HP) 8000W(3.0HP) 9000W(3.2HP) 0000W(4.0HP) 200W(4.0HP) 2500W(5.0HP) 4000W(5.0HP) Mainboard codes indication abe SW SW 234 SW 234 SW 234 SW 234 SW 234 SW 234 means factory test mode 0 means auto addressing mode (defaut setting) means DC fan is chosen 0 means AC fan is chosen A 6000W(6.0HP) NOTE 200T: Pease dia switch ENC to 8 (both system A and B). 250T: Pease dia switch ENC to 9 for system A and 8 for system B. 280T: Pease dia switch ENC to 9 (both system A and B). instaation manua

19 SW 2 Difinition SW2 234 SW2 234 SW2 234 SW2 234 SW2 234 SW2 234 SW2 234 SW means shutting down the unit to stop cod air at 5 0 means shutting down the unit to stop cod air at 20 0 means shutting down the unit to stop cod air at 24 means shutting down the unit to stop cod air at means the time of stopping TERMAL fan is 4 mintue 0 means the time of stopping TERMAL fan is 8 mintue 0 means the time of stopping TERMAL fan is 2 mintue means the time of stopping TERMAL fan is 6 mintue For 200T unit, two mainboards in the eectric contro shoud set the code ENC to 8; For 250T unit, a mainboard in the eectric contro shoud set the code ENC to 8; the other one shoud set the code ENC to 9; For 280T unit, two mainboards in the eectric contro shoud set the code to 9. For the same indoor unit, every mainboard must be different indoor unit addresses and network addresses. When using centra controer to contro the indoor unit, pease pay attention to the address setting, as the 220T, 250T and 280T units have two or more mainboards. We suggest setting the neighbor address for the mainboards in the same indoor unit. When using a centra controer for controing, mainboards in the same unit must be opened and cosed at the same time, for avoiding the unexpected incident. SW 5 Difinition SW5 2 SW5 2 SW5 2 SW5 2 SW6 Difinition SW6 2 3 SW6 2 3 SW6 2 3 SW7 Difinition SW7 2 SW means temp. compensation vaue is 6 under heat mode 0 means temp. compensation vaue is 2 under heat mode 0 means temp. compensation vaue is 4 under heat mode means temp. compensation vaue is 8 under heat mode Difinition Tabe.3- NO. Type Contents Remarks Mafunction Mafunction Mafunction Mafunction Aarm Mafunction Run amp fashes at 2.5Hz. The timer amp fashes at 2.5Hz. A the indoor aarm amps fash at 0.5Hz. When the indoor unit turns to heating mode or is turned off, the aarm wi disappear. CAUTI Pease adjust the code ENC to the suitabe position (both system A and B shoud be adjusted for 200T, 250T and 280T indoor unit). 7 Aarm Timer amp and run amp fash at 2.5Hz together. instaation manua

20 Infrared signa receiver Temporary button The test operation must be carried out after the entire instaation has been competed. Pease confirm the foowing points before the test operation: The indoor unit and outdoor unit are instaed propery. Operation amp Timer indicator Aarm indicator PRE-DEF indicator(cooing and heating type) or fan ony indicator(cooing ony type) Tubing and wiring are correcty competed. The refrigerant pipe system is eakage-checked. The drainage is unimpeded. The heating insuation works we. Pease refer to the foowing figures to insta. Connective Pipe Connective Pipe 2 Fig.4- The ground wiring is connected correcty. The ength of the tubing and the added stow capacity of the refrigerant have been recorded. The power votage fits the rated votage of the air conditioner. There is no obstace at the outet and inet of the outdoor and indoor and indoor units The gas-side and iqid-side stop vaue are both opened. 0m Liquid branch pipe Φ9.5 Φ2.7 Φ9.5 Φ5.9 Φ25.4 Gas branch pipe Φ5.9 Fig.5- The air conditioner is pre-heated by turning on the power. According to the user s requirement, insta the remote controer frame where the remote controer s signa can reach the indoor unit smoothy. Test operation Set the air conditioner under the mode of COOLING with the remote controer, and check the foowing points per the Owner s Manua If there is any mafunction, pease resove it through chapter Troubes And Causes in the Owner smanua. The indoor unit Whether the switch on the remote controer works we. Branch Part shoud be instaed in horizonta mode or vertica mode. Insta horizontay Insta verticay Main pipe is vertica to horizonta pane Whether the buttons on the remote controer works we. Whether the air fow ouver moves normay. Whether the room temperature is adjusted we. Whether the indicator ights normay. Whether the temporary buttons works we. Whether the drainage is norma. Whether there is vibration or abnorma noise during operation. Fig.5-2 Whether the air conditioner heats we in the case of the HEATING/COOLING type. The outdoor unit Whether there is vibration or abnorma noise during operation. Whether the generated wind, noise, or condensed water by the air conditioner have infuenced your neighborhood. Fig.5-3 Whether any of the refrigerant is eaked. instaation manua

21 Branch Address : Teephone : Person to be contacted : Deaer address : Teephone : Person to be contacted : Signature of the Deaer with Sea. In a correspondence/communication state your name, address, the seria number of your air conditioning unit, date of purchase and deaer s name (incude address), ocation of unit and description of probem, for prompt and immediate attention Name of Customer : Address : Sr.No. of the Unit : Sr.No. of the Compressor : Date of purchase: Invoice No : Instaation manua

22