SenTRI ONE CONTROL PANEL

Transcription

1 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI ONE CONTROL PANEL Designed to compy with EN54 parts 2 and 4 Up to 127 devices on the oop A devices connect onto the same two core oop, separate sounder wiring circuits are not required Devices can be added and system changes can be managed via the pane interface or the commissioning too SenTRI ONE s commissioning too has been deveoped specificay to improve the set up and commissioning time A buiding's fire pan can be configured either at the SenTRI ONE pane or through the simpe PC commissioning too and then upoaded to the pane via the USB port or SD card This pane is most suitabe for sma to medium sized projects SenTRI ONE has been designed with ease of use as a high priority. It is a singe oop anaogue addressabe pane with an intuitive user interface and attractive appearance. Managing up to 127 devices on the oop, SenTRI ONE is idea for sma systems. From instaation and commissioning to everyday use, SenTRI ONE deivers an eperience that makes the fire aarm system easy to use and safe to operate. The appearance of the pane means that SenTRI ONE may be instaed and ook good in any type of buiding. SenTRI ONE operates the atest range of SenTRI devices. This aows a sma system to benefit from SenTRI advanced fire detection technoogy and powered oop performance. Designed for sma buidings, SenTRI ONE offers a simpe cause and effect which can be configured by a simpe and easy to use PC commissioning too. DIMENSIONS (mm) SenTRI ONE Singe Loop Pane SENTRI1 SenTRI Contro Pane Fush Surround SENTRI1-FLUSH Loop Capacity 127 Batteries 2 7Ah Battery Standby 24 hours standby (subject to battery cacuations) Mains Operating Votage 230V +10% -6% 50Hz Appro Weight 9 Kg (with batteries) Operating Temperature 0ºC to + 45ºC Cabe entry Top and rear knockouts Standards EN54 parts 2&4 Approva 419 TECHNICAL SPECIFICATION LPCB Approved CPD Approved

2 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI TWO CONTROL PANEL Compies with EN54: Parts 2 &4 One oop and two oop options Network options for arge systems Up to 200 device capacity per 1km oop 8 ine 40 character LCD back-it dispay 32 zona fire LEDs, hidden unti it Simutaneous dispay of first and current fires Password protection for user contros Suitabe for sma to medium sized projects The SenTRI TWO Pane offers a feibe soution for sma and medium sized buidings. The standard pane comes with 1 oop capabe of connecting 200 devices. An additiona oop can be added to the same pane doubing the size of the system managed by the same pane. For arger buidings, many SenTRI panes can be connected in a network of up to 10 panes. The network card deivers a fuy secure and faut toerant network oop. The feibe architecture deivers a saving in instaation costs and a system that can be etended to meet the changing needs of a buiding throughout its ife. The SenTRI TWO pane meets a the requirements of BS 5839 Part zona fire LEDs provide a rapid identification of any zone in fire and the LCD dispay ceary presents information on the system status and pinpoints the eact ocation of an aarm. The SenTRI TWO pane and detection oop provides a powerfu and feibe system. A SenTRI oop can manage up to 200 devices. Sensors, ca points, sounders, interfaces and repeat panes a connect to the same 2 core circuit deivering power and contro without the need for additiona power suppies. Powerfu contro pane software manages the detection of fires and fire pans can be configured to ensure the safe management of the buiding once an aarm is discovered. Contro pane SENTRI2 Network card SENTRI2-NC Fush Fiing Frame Additiona Loop Card SENADV-FLUSH SENTRI2-LPC

3 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI TWO CONTROL PANEL Contro Pane Outputs Maimum 2 Master Aarm Circuits 24V dc each RS232 / RS485 Seria Communications Port 1 dedicated RS485 Seria Communication for LCD repeat pane 1 Configurabe Reay 24V dc) 2 Auiiary Contacts, programmabe reays to operate with fire, faut or disabement 24V dc) TECHNICAL SPECIFICATION Ma Number of Loops 2 Loop Capacity 200 Networking Capacity Up to 10 panes/nodes Ingress Protection IP31 Appro Weight 16.6 Kg (with batteries) Operating Temperature 0ºC to +45ºC Batteries 2 12Ah Battery Standby 24 Hours + 30 minutes aarm Mains Operating Votage 230V +10% -6% 50Hz Cabe Entry Top and rear Dimensions W H D (mm) Auiiary Contacts Programmabe to activate on Fire, Faut or Disabement. (1 SPCO 1 DPCO) Sounder Circuits 2 250mA each Monitored input 1 input which is programmabe to perform a ogica action via a command buid Communication ports 1 RS485 Repeat Pane Ony (SENADV-IND) 2 RS232 Seectabe functions Standards EN54 Parts 2 & 4 Approvas LPCB Approved and CPD Approved DIMENSIONS (mm)

4 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI FOUR CONTROL PANEL Designed to EN54: parts 2 and 4 PC based commissioning toos aow compe fire pans to be configured and feibe programming options are avaiabe at the pane. The contro pane has a simpe user interface with LCD screen providing accurate information in an emergency Networks of up to 10 panes can be programmed seamessy as one system. 2 and 4 oop panes can be connected on the same network aowing feibiity of design In the event of a fire or faut, SenTRI's anaogue addressabe technoogy wi provide a detaied og of events A buit in printer fitted to the SenTRI FOUR can be used to print out device configurations, oop maps and historic ogs. A menu option is avaiabe to turn off the printer when a printed record is not required EN54 Contro Panes 1 to 4 Loop Contro Pane SENTRI4 SenTRI4 Loop Card SENTRI4-LPC SenTRI4 Network Card SENTRI4-NC SenTRI4 Master Contro Card (MCC) SENTRI4-MCC-24 SenTRI4 Input/Output Card SENTRI4-IOC-DOM Fush Surround SENTRI4-FLUSH The SenTRI FOUR anaogue addressabe fire detection and aarm system offers medium to arge sized buiding owners the atest in system feibiity and contro pane aesthetics. The SenTRI FOUR pane manages up to 4 oops each accommodating up to 200 devices on each oop, incuding repeat panes, interfaces, ca points, sensors and sounders. The back it LCD dispay presents cear indication of Fire or faut ocation and the contro panes innovative 8 ine 40 character dispay with push button keypad is simpe to use.

5 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI FOUR CONTROL PANEL TECHNICAL SPECIFICATION Ma Number of Loops 4 Loop Capacity 200 Contro Pane Batteries Battery Standby Mains Operating Votage Appro Weight Operating Temp Cabe Entry 2 21Ah 24 hours standby + 30 minutes aarm upgradeabe to 72 hours 230V +10% -6% 50Hz 16.2 Kg 0 C to +45 C Top and rear knockins Standards EN54 Parts 2 & 4 Approvas LPCB Approved and CPD Approved DIMENSIONS (mm)

6 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI REPEAT PANEL The SenTRI repeat pane dispays a information provided to the main contro pane as we as providing main contro functions. These fuy functiona repeat panes are connected to the detection oop thus aowing them to be distributed around the buiding. This pane is ony compatibe with SenTRI TWO and SenTRI FOUR instaations. TECHNICAL SPECIFICATION Ma Number per Loop 4 Loop Capacity N/A Batteries 7AH Battery Standby 72 Hours + 30 minutes aarm Mains Operating Votage 230V 50Hz +10% -6% Emission BS EN : 2001 Immunity BS EN : 1996 : Part 4 LVD BS EN Appro Weight 9 Kg Operating Temperature 0ºC to +45ºC Cabe Entry Top and rear entry knockins 403 DIMENSIONS (mm) Fuy Functiona Loop Controed Repeat Pane (ma 4 per Loop) SENTRI-RPT Repeat Pane Fush Surround 338 SENTRI-RPT-FLUSH 101

7 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI LCD REPEAT PANEL An affordabe LCD repeat pane is avaiabe to support the SenTRI contro pane. This neat unit can be powered from the SenTRI pane and is driven from a dedicated RS485 repeat output. The LCD repeat pane indicates Fire, Faut and Disabement information on a 40 character dispay, either directy as events occur or by accessing the ogs via dedicated keys. A maimum of 4 Repeat Panes can be connected to a SenTRI contro pane. This pane is compatibe with SenTRI ONE, SenTRI TWO and SenTRI FOUR instaations. TECHNICAL SPECIFICATION Ingress Protection IP30 Suppy Votage 21 30V dc Power Consumption Appro 30 ma Appro Weight 0.75 Kg Operating Temperature 0ºC to +45ºC Communication ports 1 RS485 to communicate with the main contro pane Cabe Entry Top and rear knockins 177 DIMENSIONS (mm) 206 Specific Wiring Detais for a SenTRI TWO project LCD Repeat Pane (indication ony) 49 RS Vdc Ma Cabe Length 1000M LCD Repeat Indicator Connects to the contro pane via the RS485 seria ink SENADV-IND One LCD repeat pane can be powered from the contro pane, additiona repeat indicators must be powered from an additiona power suppy. The communication ink to the pane is monitored, so if power to the repeat indicators fais the faut wi be reported at the contro pane. Monitored Battery Backed 24V PSU SenTRI Contro Pane

8 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI A3 MIMIC PANEL Dispays up to 128 zones and gives a rapid, visua indication of the ocation of any fire incident Used to provide an indication of faut and supervisory events in the fire system Pane suppied with preprinted and bank high quaity UV protected A3 sheets Site configuration hed in fash memory so site changes can be programmed on site without changing LEDs or eectronics TECHNICAL SPECIFICATION Mains Operating Votage 230V 50Hz +10% -6% Ma Number per Loop A maimum oad factor of 1000 aowed per SenTRI oop circuit Maimim number of combined repeat and mimic panes per oop = 4 Load factor per pane = 3 Loop Connection 3-way connection to a oop circuit Indicators 1536 high intensity RED LEDs Ingress Protection IP30 (estimated) Appro Weight 7.9 Kg (without batteries) Operating Temperature 0ºC to +45ºC Storage Temperature -10ºC to +55ºC Reative Humidity (Non condensing) Up to 90% temperature 5ºC 45ºC Batteries 2 7Ah seaed ead acid (weight 1.3Kg each) The integra battery provides power for 72 hours in standby condition and a further 30 minutes in aarm Emission BS EN : 2001 Immunity BS EN : 1996 : Part 4 LVD BS EN Contro Cance faut buzzer / amp test button Coour Door Pantone 422 Back bo Graphite Grey (RAL 7024) 10.5 Kg (with batteries) 375 DIMENSIONS WITH BACK BOX (mm) SenTRI A3 Mimic Pane SENTRI-ZONE

9 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI SENSOR RANGE Compete range of sensors and mutisensors Patented mutifunction sensor sounder and sensor sounder strobe LED output and monitored input faciity on every device Powerfu software agorithms to minimise fase aarms SENSOR SOUNDER Advanced sensing technoogy couped with integra sounder and strobe in one inteigent device Attention tones can be programmed either as a be* or a choice of standard tones provides the UK s most innovative soution to the detection and signaing of fires. Soft start (Voume option) power in the sensor as we as the power of the SenTRI contro pane inteigence to achieve Low current consumption fast fire decisions. SenTRI combines traditiona sensing technoogy with innovative techniques Fuy synchronised sound patterns via the contro pane increasing the integrity of the fire decision and minimising incidents of fase aarms. Rich harmonic sound output using patented design Each SenTRI sensor has sensitivity settings managed by the pane which can be adjusted to suit High sound output: or night. 90 (typica) SENSOR SOUNDER STROBE A strobe option warns those with hearing difficuties of a potentia fire hazard, now a ega requirement in a pubic buidings through the Equaity Act 2010 Legisation Low power consumption and high output LED technoogy ensures SenTRI strobes are cost efficient and more reiabe in use than other high powered strobes Wide viewing ange synchronised across the oop Strobe can operate independenty of the sounder if required Strobe variant incudes be tone idea for cass change in schoos * Be tone ony avaiabe on Sensor Sounder Strobe SenTRI sensors empoy true anaogue detection techniques combining eceptiona processing the environment / appication and can be programmed for different time periods during the day SenTRI SENSOR SOUNDER STROBE This cost effective soution saves money on the number of devices required to satisfy the site and Equaity Act 2010 (formery Disabiity Discrimination Act) requirements, as we as impacting hugey on both the cabing requirements and the abour time needed to insta the device. In addition, shoud the sound output need to be raised in particuar areas, it is easy to repace a sensor for a sensor sounder directy into the base unit aready instaed. Synchronised tones and the high intensity strobe are transmitted through the same sensor that detects the fire. This neat device is a cost effective way to deiver compiance to the fire detection and aarm requirements of the Equaity Act 2010 (formery Disabiity Discrimination Act).

10 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI SENSOR RANGE The patented combined sensor sounder strobe technoogy provides a cost effective soution for aarm signaing. The fuy integrated high quaity sounder and strobe in the sensor housing offers a power efficient soution to a site requirements. The sounder and strobe functionaities within the sensor are fuy compatibe and synchronised with SenTRI Sounder Strobes instaed on the same system. The tabe beow shows the various states of these smoke sensor options. SenTRI Optica Sensor SenTRI Optica Heat Sensor SenTRI Optica Heat Sensor Sounder SenTRI Optica Heat Sensor Sounder & Strobe*** SenTRI Heat Sensor SenTRI Heat Sensor Sounder SenTRI Heat Sensor Sounder & Strobe*** SEN-715 SEN-710 SEN-770 SEN-770-ST SEN-720 SEN-780 SEN-780-ST SenTRI Detector Base (With Remote LED Output) S4-700 SenTRI Semi-Fush mounting kit S4-FLUSH SenTRI Sensor Dust Cover (50 Pack) SenTRI Remova Too Kit SenTRI Dust Cover Remover (Spare remover too c/w sucker) S4-COVER-REMOVER SenTRI Base Labe Pate (10 Pack) *** This product is not a visua aarm device and does not meet EN SENTRI OPTICAL/SMOKE & HEAT SENSOR STATE SENSOR Description of State set up 0 OHeat Medium Optica + A1 Heat 2 OHeat Low Optica + A1 Heat 3 OHeat High Optica + A1 Heat 5 OHeat Medium Optica + B Heat 6 OHeat Low Optica + BS Heat 8 OHeat Deayed Medium Optica + A1 Heat 11 OHeat Low Optica + B Heat 12 OHeat A1 Heat Ony 15 OHeat A channes set to off TECHNICAL SPECIFICATION Heat Sensor Sounder Optica Heat Sensor Sounder Device Load Factor* 8-16** 8-16** Ingress Protection IP30 Appro Weight 0.11 Kg (0.17 Kg with base) Operating Temperature -10ºC to +50ºC Reevant Standards EN54 Parts 3 & 5 EN54 Parts 3 & 7 +5 Sound Output at 1m Typicay 90 db(a) Approvas (EN54 Parts 5 & 7) LPCB Approved and CPD Approved * Load factors for guide purposes ony. ** Higher oad factor for be tone. DIMENSIONS (mm) 48 (62 with base) 117

11 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI VISUAL ALARM DEVICES High efficiency design aows more devices per oop e.g. up to 200 sounders can be powered per oop EN54 part 23 VAD with industry beating coverage Active monitoring of sounder and VAD circuit A tones and visua aarms are synchronised across oops in the same contro pane Compements the SenTRI sensor with compe sound signas The HandiLink remote contro makes it much easier to adjust the sound eve in situ Products incorporate innovative design features which are patented Combined VADs and Sounder VADs aow compete compiance with the Equaity Act 2010 The SenTRI wa sounder VADs incorporate EN54-23 visua aarms and sound in one device. The range offers a variants in a choice of red or white fash with either a standard IP 21 rating or an EP variant meeting IP66. The range offers this industry beating functionaity a powered by the oop. The SenTRI Sounder VADs have been designed to assist with compiance to the fire detection and aarm requirements of the Equaity Act 2010 (formery Disabiity Discrimination Act). As an aid to commissioning, there is the option to use the HandiLink Infrared remote contro to adjust the voume in the room without the need for physica or mechanica access to the device. Password access at the contro pane is required to enabe this feature so it is not possibe to make this adjustment accidentay or maiciousy. TECHNICAL SPECIFICATION 1.0 WALL SOUNDERS Type Appro ma quantity per Loop (dependent on oop oad) Ingress Protection Appro Weight Operating Temperature Sound Output at 1m IR Contro Operating Distance System Sounder Standard Tone Inc Be Sound Standard range IP Kg -10ºC to +50ºC 103 db(a) ± 3m Standards Certified to EN54 Part 3 (sounders ony) and EN54 Part 17 Approvas LPCB approved to EN54-3, and EN54-17

12 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI VISUAL ALARM DEVICES TECHNICAL SPECIFICATION 1.1 SOUNDERS WITH VAD Type Integrated Sounder and VAD VAD Ony Strobe Coour Red or White Red or White Appro Ma Quantity per Loop (dependent on oop oad) Ingress Protection Standard range High Power 38 Medium Power 47 Low Power 72 High Power 44 Medium Power 57 Low Power 100 IP21 Ingress Protection EP range Appro Weight Operating Temperature Sound Output at 1m IP66 0.3Kg -10ºC to +50ºC 103 db(a) ± 3 db(a) VAD Category - High Performance Power setting High Medium Low Red W W W VAD Category Standard Performance* VAD Fash Frequency Approvas White W W W Red and White units W Hz Sounder VAD EN54-3, EN54-23:2010, EN54-17, VAD - EN54-23:2010, EN54-17 * The Standard Performance category reates to a restricted number of devices in the range, pease see part numbers in the beow tabe. NB: To use the new range of sounders the pane software (main & repeat) may need to be upgraded. Sounders Sounder/Red Body SEN-S-R DIMENSIONS (mm) Standard Base IP21 EP Range IP66 Sounder VAD Sounder/HP White VAD/Red Body SEN-S-VAD-HPW-R Sounder/HP Red VAD/Red Body SEN-S-VAD-HPR-R VAD HP White VAD/Red body SEN-VAD-HPW-R HP Red VAD/Red Body SEN-VAD-HPR-R Standard Power Sounder VAD Sounder/Standard Power White VAD/Red Body Sounder/Standard Power Red VAD/Red Body SEN-S-VAD-LPW-R SEN-S-VAD-LPR-R Environmentay Protected (EP) Range SenTRI EP (IP66) Sounder Red Body SEN-S-EP-R SenTRI EP (IP66) Red Body Sounder High Power White VAD SEN-S-VAD-HPW-EP-R SenTRI EP (IP66) Red Body Sounder High Power Red VAD SEN-S-VAD-HPR-EP-R * HP - High Performance VADs are configurabe during commissioning to one of three intensity settings

13 ANALOGUE ADDRESSABLE FIRE SYSTEMS BEAM SENSORS Loop powered supporting 16 pairs per oop (8 pairs on SenTRI one). Each beam can be set to one of 6 sensitivity states to provide a best fit for individua appications. The beam provides increased resiience to interference from the sun and other ight sources. Remote key switch can be used to provide a test faciity at ground eve without the need to gain access to beams mounted in high areas. The beam incorporates an LED array to indicate signa strength aowing accurate aignment during one person commissioning. Optimum sensitivity is maintained by automatic gain setting triggered at the beam during aignment. The optica ens design is intended to minimise buid up of dust to reduce the maintenance and ceaning required. Designed to meet EN54:Part 12 and EN54: Part 17 Product is rated at IP30 Beam Transmitter Beam Receiver The SMS SenTRI-Beam provides an enhanced soution for inear beam detection for appications where point detection is either not practica or uneconomic. SenTRI oop powered technoogy aows up to 16 beam pairs to be connected to the same oop circuit, each covering a distance of up to 100m without the need for an eterna Power Suppy Unit, wiring or interfacing. Compatibe with the fu range of SenTRI contro panes the SenTRIBeam uses the pane software to ensure a fast response to fire whie offering software fiters to reduce the number of unwanted aarms.

14 ANALOGUE ADDRESSABLE FIRE SYSTEMS BEAM SENSORS TECHNICAL SPECIFICATION Ambient temperature Storage temperature Protection Cass -10 º C to +60 º C -15 º C to +65 º C IP30 (IP20 when mounted on bracket) Housing ABS Pastic Transmitter or receiver 105g Ange bracket and base 620g Weight Parae bracket and base 600g Light shied 14g Transmitter or receiver: (mm) Dimension (HWD) Ange Bracket with base: (mm) Parae bracket: (mm) Operating votage 35-41V Coour RAL 9010 Emissions BS EN :1992 part 1 residentia, commercia and ight industry Cass B imits Immunity BS EN : part 4 Aarm systems Transmission Path Standards 2 100m Designed to meet EN54:Part12 and EN54:Part17 Approvas LPCB Pending Approva. States 0,1,2 and 3 DIMENSIONS (mm) 130mm 27mm 145mm 152mm 117mm Beam Pair Ange Bracket Parae Bracket Light Shied Test cards SENTRI-BEAM SEN SEN S S

15 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI MANUAL CALL POINTS An EN54 part 11 compiant addressabe ca point with a response time of ess than 3 seconds. Avaiabe options: Resettabe or break gass Surface and fush mounted into a back bo Anti vanda ift up cover Simpe gass repacement process LED confirmation of operation Weather resistant version rated at IP67 TECHNICAL SPECIFICATION Ma Quantity per Loop 200 Operating Temperature Ingress Protection Appro Weight -25ºC to +55ºC Standard MCP - IP43 EP Version - IP Kg Device Load Factor 1 Certification / Approvas SEN-805, SEN-805-EP & SEN-800 = EN54-11, EN54-17 SEN-807 (key-operated version) EN54-17 Note: SEN Key operated MCP is not covered in EN If required on a site the need for a variation to BS shoud be considered. SenTRI Manua Ca Point (Gass) IP43 SenTRI Manua Ca Point with Resettabe Eement SEN-800 SEN-805 DIMENSIONS (mm) 87 Removabe Termina bock SenTRI Surface Mounted Key switch MCP compete with back bo SEN-807 IP 67 SenTRI Manua Ca Point with resettabe eement and back bo SEN-805-EP Resettabe Eement for SenTRI MCP (sod in packs of 10) price per pack Repacement Gass for SenTRI MCP (sod in pack of 10) price per pack SEN-890 SEN Protective Cover for SenTRI MCP Range (sod in pack of 20) price per pack S Surface Back Bo for SenTRI MCP (Red) (Sod in packs of 10) price per pack SEN-895 Test Key for SEN-800 range of MCP (sod in packs of 25) price per pack S A set of keys for Key Switch Interface and MCP (1 set = 2 keys) S

16 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI INTERFACES A comprehensive range of SenTRI system interfaces aows pant contro and connection to other ife safety systems such as sprinkers. SenTRI interfaces provide highy feibe functionaity and most units are oop powered without the need for separate power suppies. A range of mounting options is avaiabe making it easy to design and insta the SenTRI interfaces. TECHNICAL SPECIFICATION Output Interface (Mains) Low Votage Input / Output Range Singe Input SEN-INT-INPUT c/w meta encosure SEN-INT-AC Output Interface (mains switching 240V, 13A) c/w DIN Rai mounting kit Singe Input/ Output SEN-INT-OUTPUT SEN-INT-AC / SEN-INT-ACDIN 100g ➀ DIN mountabe: 138g PCB with cover in meta bo: 800g Weight 92g ➀ Operating Temperature -10ºC to +60ºC Reative Humidity Up to 95% Temperature +5ºC to +45ºC (Non condensing) Ingress Protection IP31 for pastic bo SEN-490 IP40 estimated for meta bo SEN-492 Meta bo IP40 estimated Load Factor Load Factor 1-4 switch inputs = 1 (maimum 200 per oop) 1-4 reay outputs = 2 (maimum 200 per oop ony 8 individuay sectored) Zone Input = 26 (maimum 30 per oop) Every LED output = + 5 (maimum 100 LED outputs per oop) 5 (maimum 200 devices per oop) Pane Compatibiity Compatibe with Loop = V4.35 and Main Contro Card = V4.37 Standards EN54-17 and EN54-18 Approvas LPCB Approved Output Interface (mains switching 240V, 13A) Four Channe Input/Output (I/O) SEN-INT-4IO 100g ➀ SEN-INT-ACDIN DIMENSIONS (mm) Input Interface (ow votage reay 30V, 1A) SEN-INT-INPUT Output Interface SEN-INT-OUTPUT 4 Channe Input Output Unit SEN-INT-4IO 93 (ow votage reay 30V, 1A) Key Operated Output Interface (ow votage) Interface Housing (pastic) SEN-INT-KEY SEN-490 DIN Rai Mounting Kit (pack of 5) SEN-491 Interface Housing for Singe Channe (meta) SEN

17 ANALOGUE ADDRESSABLE FIRE SYSTEMS Enhanced SenTRI Loop Card SMS's a new Loop Card provides EN54-23 compiance and increased ma aarm oad. Key Features Increased capacity for oop powered devices incuding the new EN54-23 visua aarm devices Loop current increased to 800mA when used with the atest SenTRI devices The new Loop Card is designed to fuy compy with EN54-23 and is avaiabe on EN54 versions of the SenTRI TWO and SenTRI FOUR systems. The increased power aows for up to 100 EN5423 sensor-sounder-strobes, managing up to 200 devices in tota. SCHEMATIC Benefits Improved efficiency with 2 times more aarm power with no oss of standby Supports up to 100 SenTRI Sensor Sounder VADs certified to EN54-23 MCP Supports the upgrade of eisting SenTRI instaations SenTRI Sensor Sounder VAD SenTRI Interface Ma Loop Current 800 ma Note: the Loop Load design too must be used to ensure design imits are not eceeded. SenTRI Sounder SenTRI FOUR Pane SenTRI Sounder SenTRI Sensor Sounder

18 ANALOGUE ADDRESSABLE FIRE SYSTEMS Enhanced SenTRI Loop Card C O M PAT I B I L I T Y O F PA N E L S A N D LO O P D E V I C E S SPECIFICATION NEW LOOP CARD OLD LOOP CARD FULL < 800MA 1KM < 400MA PANELS DATE OF MANUFACTURE RESTRICTED < 400MA SenTRI TWO and SenTRI FOUR Sept present SenTRI TWO and SenTRI FOUR present Senator (1 & 2) Recommend Upgrade SENSORS WITH SENSOR SOUNDER AND VAD SenTRI Sensors SenTRI Sensor Sounders Aug 2014 SenTRI Sensor Sounders Sept present SenTRI Sensor Sounder Strobe Aug 2014 SenTRI Sensor Sounder Pus VAD present Compatibiity Mode Senator 2 Sensors Senator 2 Sensor Sounders Senator 1 Sensors Compatibiity Mode SOUNDERS SenTRI Mark 3 Sounders SenTRI Mark 3 Sounders with VAD To be aunched end of 2014 SenTRI Mark SenTRI Mark 2 Sounder and Sounder Strobe SenTRI Mark 1 Sounder Senator 2 Sounders Senator 1 Sounders SenTRI MCP Senator MCP SenTRI Mains Switching Interfaces SenTRI Mains Powered Interface SenTRI Loop Powered Interfaces Senator Mains Powered Interface Senator Loop Powered Interfaces MANUAL CALL POINTS INTERFACES

19 ANALOGUE ADDRESSABLE FIRE SYSTEMS Enhanced SenTRI Loop Card FEATURES AND BENEFITS LOOP ALARM CURRENT The new oop card is designed to support a higher oop oad in aarm deivering a higher capacity for EN54-23 compiant visua aarms devices. The maimum aarm oad of 800mA is avaiabe ONLY with the new range of aarm devices. With any of the od range of aarm devices (SenTRI Pre September 2014) the maimum aarm oad is imited to 400mA per oop. LOOP LENGTH The oop card supports at east 1km oop ength. Loop oad design cacuator must be used to confirm actua oop design imit. This aso provides information on the effect of aarm device distribution. Eveny distributed oad with atest devices may aow increased oop engths. VALIDATING LOOP LENGTH The oop card wi automaticay measure (and dispay on the pane) the oop resistance of each oop on aocation. This wi aow engineers to easiy fufi one of the required tasks for commissioning the system. If the resistance eceeds a safe imit it wi indicate a faut. SENTRI TWO LOOP CARD EN54 pt23 ready SENTRI2-LPC-EN SENTRI FOUR LOOP CARD EN54 pt23 ready SENTRI4-LPC-EN

20 ANALOGUE ADDRESSABLE FIRE SYSTEMS SenTRI Muti-Sensor with Integrated Sounder and Visua Aarms Device (VAD) Key Features Sensor and aarm in one device reduces instaation time and cost SenTRI's muti-sensor with integrated sounder and VAD combines renowned advanced sensing technoogy with state of the art visua aarms. The ony practica soution meeting the demands of detection and the performance needed to meet the EN54 part 23 standard. Buit-in high intensity VAD heps aert occupants in noisy environments as we the hard of hearing Meets a the requirements of the Equaity Act 2010 Compatibe with the SenTRI wa mounted VAD State of the art, high efficiency visua aarm sounder Advanced power management that increases oop capacity and integrity Range of devices and power settings to suit widest range of buiding appications Coour and Performance variants High intensity option with three intensity settings to achieve maimum feibiity for different room coverage, optimising oop coverage White VADs use a muti-die LED with a 'Day White' coour Red VADs use mutipe red LEDs giving a true red coour SCHEMATIC MCP Light output that aows devices to be sited at standard smoke and heat detector spacings SenTRI Interface SenTRI Sensor Sounder VAD Synchronised fash rate across the whoe contro pane avoiding risk of induced seizures VAD can operate independenty of the sounder if required Ma Loop Current 800 ma SenTRI Sounder Cass eading VAD performance Covering upto 16m 6m ceiing height SenTRI FOUR Pane Coverage matching smoke sensor spacing SenTRI Sounder SenTRI Sensor Sounder

21 ANALOGUE ADDRESSABLE FIRE SYSTEMS

22 ANALOGUE ADDRESSABLE FIRE SYSTEMS MAINS SWITCHING INTERFACE Feibe input / output Controing outputs and monitoring inputs simutaneousy Configurabe deay to fiter noise and spurious signas Outputs can be individuay sectored The new SenTRI Mains Switching Interface units connect directy to the oop of SenTRI 2 and 4 oop systems. The interface units are designed to provide heavy duty reay switching for both 24V and 230V appications with contacts rated at 13A. This interface is particuary suitabe for switching damper contro units and other buiding contros requiring a high contact rating for mains shutdown. The new singe channe variant is a direct repacement for the eisting NM Mains Switching Interface. A new addition to the Mains Switching Interface range is the 4 channe variant which offers etended functionaity. Inputs can be configured as fire, faut, supervisory or confirmation input. An input and an output of an interface unit can be paired to operate in a confirmation mode. Eterna equipment can send an acknowedgement upon receiving a signa from the interface unit, this is caed 'confirmation input'. Eterna equipment can aso receive an acknowedgement from the Interface unit upon sending it a signa, this is caed confirmation output. Singe channe Mains Switching Interface SEN-INT-IOAC 4 channe Mains Switching Interface SEN-INT-4IOAC

23 ANALOGUE ADDRESSABLE FIRE SYSTEMS MAINS SWITCHING INTERFACE TECHNICAL SPECIFICATION Overa dimensions 227mm 245mm 77mm (H W D) Back bo (Aperture) 233mm 210mm 48mm (H W D) Assembed weight (approimate) Encosure Coour Storage temperature Ambient operating temperature Reative Humidity (Non condensing) Ingress Protection (estimated) Output(s) Reay contact rating Input(s) Modes of operation Maimum number per oop 1.1Kg ABS V-O rated Back bo Dark Grey Lid Light Grey -20 to 70 C -10 to 45 C Up to 95% Temperature 5 C to 45 C IP31 Resistive oad: Singe poe change over contacts rated 13A 230V ac. Inductive oad: 240V ac, 1/2hp 120V ac Input can be normay open or normay cosed switch Input Output Input and Output Input with confirmation Output Output with confirmation Input 100 units per oop (of which ony 8 can be individuay programmed) Standards Designed to meet EN54:part 17 and EN54:part 18 DIMENSIONS (mm) For back bo dimensions pease refer to the technica specification tabe The Mains Switching Interface unit can be fush mounted to a depth of 48mm maimum

24 ANALOGUE ADDRESSABLE FIRE SYSTEMS MAINS POWERED INTERFACE It has a configurabe auiiary powered output that is derived from its sef contained EN54 part 4 compiant mains powered suppy unit A cost effective soution as a eements are incuded within the encosure therefore reducing your instaation and maintenance costs Four channes can be individuay programmed to provide various configuration modes to contro eterna equipment The SenTRI Mains Powered Interface aows you to connect to anciary units which can not be integrated directy onto the SenTRI oop. The highy feibe interfacing capabiity of the unit offers superior functionaity and a powerfu soution to meet the fundamenta requirements of appications requiring compiance to BS7273 part 4. This unit aso offers a practica and cost effective soution for Intrinsicay Safe appications. BS7273 FUNCTIONALITY BS7273 part is the code of practice governing door hoders and door reease mechanisms. With the atest software, SenTRI offers a compiant soution with a mains powered interface. No further equipment is necessary as Interface outputs can be configured to be both Category A or B door reease outputs. BS7273 functionaity is ony avaiabe in EN versions of SenTRI. It is possibe to turn off any of the outputs under mains fai conditions to preserve battery capacity. INTRINSICALLY SAFE APPLICATIONS Integration of Intrinsicay Safe devices with the SenTRI product range is now far simper with the new Mains Powered Interface. The Intrinsicay Safe devices can be connected directy into the isoation barriers housed within the unit thus ensuring that Intrinsicay Safe appications are cost effective and no onger require eterna encosures and power suppies. Mains Powered Interface NM

25 ANALOGUE ADDRESSABLE FIRE SYSTEMS MAINS POWERED INTERFACE TECHNICAL SPECIFICATION Maimum Number per oop Overa dimensions Assembed weight (approimate) Encosure Coour Storage temperature Ambient operating temperature Reative Humidity (Non condensing) Ingress Protection (estimated) Operating votage 100 units per oop (ony 8 with fuy sectored outputs) 478mm 322mm 128mm 7Kg (ecuding batteries and optiona components fitted) Stee RAL7024 Graphite Grey (fine tetured) 20 C to 70 C 10 C to 45 C Up to 95% Temperature 5 C to 45 C IP31 230V +10% -6% 50Hz Rated current 0.7A Input modes Input can be faut monitored, votage free contacts OR conventiona detection Zone circuit Refer to the commissioning information for more detais 20mA per zone (defaut) Zone short circuit current imited to < 30mA Quiescent current EN54 compiance imitation: 32 devices OR Maimum of 20 diode bases per zone Output modes Outputs are monitored 24V (nomina) 0.5A OR LED drive. Refer to the commissioning information for more detais It is possibe to configure a Inputs and Outputs as confirmation Confirmation modes channes Sector and Auiiary Outputs - Sector and Auiiary Outputs 0.5A ma 24V +/-3V Maimum tota output current 1.5A Auiiary power output Batteries 24V +/- 3V 2 12V 2.1Ahr (1Kg each) for NM Minimum Software Requirement MCC 4.43, LPC 4.41, Commissioning Too 1.27 Standards Designed to meet EN54:part 4, EN54:part 17 and EN54:part 18 Approvas LPCB Pending Approva DIMENSIONS (mm)

26 ANALOGUE ADDRESSABLE FIRE SYSTEMS INTRINSICALLY SAFE RANGE To support the introduction of the new Mains Powered Interface, SMS now offers a range of Intrinsicay Safe sensors and sounders which provide a cost effective soution for instaations specificay in hazardous areas. Appications such as Nucear Power, pharmaceutica and chemica industries are particuary suitabe for the soution. Fammabe gases, mist and vapours from fammabe iquids as we as couds of fammabe dusts can form a dangerous eposive atmosphere, resources such as eectrica and mechanica devices can represent a very huge risk to the fire industry. Areas that can be ignited by spot combustabe surroundings ie grain and yeast stores, cean and boier rooms are aso idea appications for this soution. Gavanic Isoator (1 - Channe) for use in Mains Powered Interface Aarm Driver (Ma of 4 Sounders Per Driver) Intrinsicay Safe Heat Detector (Rate of Rise) EX Intrinsicay Safe Optica Smoke Detector EX MCP IP66 Eposion Proof C/O Surface Mounted Type IS28 Banshee Sounder L.F/V.C 24V dc 10mA

27 ANALOGUE ADDRESSABLE FIRE SYSTEMS INTRINSICALLY SAFE RANGE GENERAL SPECIFICATION Operating votage 8 V DC to 42 V DC Type of sensor Rate of Rise Heat Detector and Optica Smoke Detector (see tabe beow for specifications) Monitored area ma. 30 m² ma. 110 m² Mounting height Aarm indicator Air veocity range Temperature, storage Ambient humidity IP rating Housing ma. 7.5 m ma. 12 m red LED, fashing 0 to ft/min. -25 C to +75 C 95% reative, (non-condensing) IP 43 (with base + optiona base gasket) ABS Coour white (simiar to RAL 9010) Weight Dimensions (with base) appro. 110 g Ø 117 mm, H = 62 mm GENERAL SPECIFICATION - DETECTORS Rate-of-rise heat detector Quiescent 19 V DC Ambient temperature 40 μa -20 C to +50 C Specification EN 54-5A1R : 2000 / A1 : 2002 VdS approva G CE certificate CPD Optica smoke detector Quiescent 19 V DC Ambient temperature 50 μa -20 C to +70 C Specification EN 54-7 : 2006 VdS approva G CE certificate CPD TECHNICAL SPECIFICATION Genera detector data according to ATEX Ma. Input votage (Ui) Ma. Input current (Ii) Ma. Output current (Io) Ma. interna Capacity (Ci) 21 V DC 252 ma 10 ma 1 nf Ambient temperature (Ta) 20 C to + 70 C Eamination Certificate No. TÜV 09 ATEX Category II 2G (with safety barrier Part No ) (Part number ) E-protection E ib IIC T4

28