YZ667A1060. Wireless Domestic Heating Zoning System 1 GENERAL 2 TECHNICAL INFORMATION TABLE OF CONTENTS INSTALLATION GUIDE

Transcription

1 YZ667A060 Wireless Domestic Heting Zoning System INSTALLATION GUIDE GENERAL HC60NG Rely Module CM67z Room Unit HR80UK Rditor Controllers TABLE OF CONTENTS Section Pge Generl... Technicl Informtion... 3 Fctory Configurtion... 4 HC60NG Rely Module CM67z Room Unit HR80UK Rditor Controller System Testing Service mode Chnging the Configurtion Prmeters of the CM67z Chnging or dding HR80UK to zone Built -in sensor configurtion Adding HC60NG Zone vlve controller Resetting Bound HR80UK Trouble Shooting Trouble Shooting Guide Mnul dption Def (defult setting) nd Full operting modes Resetting the HR 80 to the fctory settings... The CM Zone Wireless Domestic Heting Zoning System offers high levels of comfort nd energy svings for the home. It provides the bility to control two individul zones t different comfort levels nd t different times. A typicl exmple being the living res nd the bedrooms being controlled seprtely. The stndrd CM Zone Pck contins Room Unit, Rely Module nd six Rditor Controllers ll pre-bound with three Rditor Controllers bound to Zone nd three bound to Zone. The System cn be expnded or modified nd the methods used re described within this Guide. To get the best from the instlled system it is recommended to use Honeywell VT5, VT7 or VT00 TRV bodies nd Honeywell DU45 Automtic Bypss Vlve. For ppliction support plese contct your nerest Honeywell slesmn, for technicl ssistnce plese contct the Honeywell Technicl Help Desk, detils re on the bck pge. TECHNICAL INFORMATION Type numbers CM67z - Room Unit (x) HR80UK - Rditor Controller (x6) HC60NG - Rely module (x) Mteril Housings mde of plstics (ABS). Dimensions CM67z - 55 x 05 x 30 mm. (l x h x d) HR80UK - 50 x 80 x 05 mm. (l x h x d) HC60NG - 3 x 97 x 36 mm. (l x h x d) Power CM67z - x.5 V IEC LR6 (AA) Alkline cells HR80UK - x.5 V IEC LR6 (AA) Alkline cells HC60NG - 30V~ 50Hz powered Electricl wiring (only for HC60NG) Mins power supply Rely output rting: 4-30 V~, 0A resistive, 3A inductive 0.6 p.f. Progrmming Cpbility individul heting progrms 7 dys with 6 temperture chnge times per dy Approvls DIN EN ISO 900/400, CE, EN (000), EN (00), EN5504- (000), EN5504- (997), ETSI EN (000), ETSI EN (000) R3

2 Section 3: Fctory Configurtion The Hydronic Zoning kit is fctory pre-configured nd hs the following components: Zone - Three HR80UK Rditor controllers lbelled Zone - Two HR80UK Rditor controllers lbelled HC60NG - Rely box CM67z - Room Unit Zoning Exmple Zone : Living Room + Kitchen (downstirs) Zone : Bedrooms (upstirs) Zone To chnge this fctory configurtion or to dd components plese see Section 8: Chnging the Configurtion. Zone A typicl trditionl system with open vented hot wter storge tnk Conventionl Boilers These re used in trditionl centrl heting systems in the UK. A typicl COMBI system Combintion Boilers With combintion boiler, hot wter nd centrl heting requirements re provided from the one unit.

3 Section 4: HC60NG Rely Module The HC60NG Rely Module is n integrl prt of the CM Zone Control System. It is designed to control Domestic Boiler, Vlve, pump or Electric Heting pplinces. In the stndrd CM Zone Pck the HC60NG Rely Module is configured to control Boiler bsed upon demnd signls received from the HR80UK Rditor Controllers either directly or vi Y Pln / S Pln connection described below. For control of other pplictions see Section 8: Chnging the Configurtion.! Cution! When selecting the operting site of the HC60NG ensure tht the distnce to other wireless devices such s wireless hedphones, cordless phones etc. is t lest -m. HC60NG Rely Module Plese note: Mximum wire size.5mm. SPDT rely suitble for V~, 0A resistive, 3A inductive The HC60NG is rdio frequency (RF) device nd for the best performnce should be instlled in n open spce. Leve t lest 30cm distnce from ny metl objects including wll boxes nd the boiler. NOTE: The HC60NG contins no user serviceble prts. It should be opened nd instlled by qulified instller only. WARNING: Electrosttic sensitive device! Do not touch the circuit bord. 3 4 Typicl Burner / Boiler connections. Burner (direct control) HC60NG b. Combi boiler HC60NG < 7mm > 7mm.0-.5mm² 6mm mx. NOTE: Instll in ccordnce with locl wiring regultions Cution: Observe mbient temperture nd current limits (see HC60NG wiring lbel) 5 6 Honeywell Y Pln Connections HC60NG Honeywell S Pln Connections HC60NG Typicl Y Pln Junction Box Typicl S Pln Junction Box NOTE: For existing Y Pln remove only Room Thermostt connections from Junction Box Terminls nd replce with Connections to HC60NG. NOTE: For existing S Pln remove only Room Thermostt connections from Junction Box Terminls nd replce with Connections to HC60NG. 3

4 AM PM Section 5: CM67z Room Unit The CM67z Room Unit provides centrl point from which to configure the system nd set the time nd temperture profiles for ech Zone. At given time, s defined within Zone profile, the CM67z Room Unit trnsmits the required temperture setpoint to the respective HR80UK Rditor Controllers, locl temperture control nd override is then provided t ech HR80UK Rditor Controller. In the defult setting, the CM67z Room Unit on-bord sensor is disbled. This my be enbled for certin pplictions s described within Section 8: Chnging the configurtion For norml opertion refer to the CM Zone User Guide CM67z Room Unit! Cution! When selecting the operting site of the CM67z ensure tht the distnce to other wireless devices such s wireless hedphones, cordless phones etc. is t lest -m nd t lest m to other electricl devices. Do not mount the CM67z on metl surfces or wll boxes. Positioning The CM67z is RF device nd for the best performnce should be instlled in n open spce. Leve t lest 30cm distnce from ny metl objects including wll boxes. Setting the clock MAN MAN Move the CM67z slider to position. When setting the dte nd time for the first time fter btteries were inserted the zone controller disply will flsh s shown. Press the + or - buttons to set the current yer (e.g. 03 = 003) Tble Stnd Wll Mounting MAN MAN Press the button to go to the month: Press the + or - to set the current month (e.g. 0 = Jnury). Press the button to go to the dy of the month: 6 Dy of the week indictor MAN MAN Strt up 3 Press the + or - to set the current dy of the month. Check if the dy mrker on the disply indictes the correct dy of the week MAN MAN Remove the insultion tb from the CM67z bttery comprtment. Press button to go to the time: Press the + or - until the correct time is displyed. Holding the button for few seconds will chnge the time slowly then quickly. 4

5 Section 6: HR80UK Rditor Controller The HR80UK Rditor Controller provides locl room temperture control bsed upon setpoint informtion received from the CM67z Room Unit nd sends Lod Demnd signls bsed upon room conditions to the HC60NG Rely Module. Setpoints cn be temporrily overridden using the djustment dil. The HR80UK cn be fitted onto Honeywell VT5, VT7, VT00 nd mny other mnufcturers TRV bodies with M30x.5mm thred nd mm vlve closing point, dptors my be vilble for mnufcturers with non stndrd connections. For more informtion contct Honeywell Technicl Help Desk, detils on the bck pge. HR80UK Rditor Controller! Cution! When selecting the operting site of the HR80UK ensure tht the distnce to other wireless devices such s wireless hedphones, cordless phones etc. is t lest -m. In the stndrd CM Zone Pck the HR80UK Rditor Controllers re pre-bound to ech zone s indicted by the zone number lbel. To dd dditionl HR80UK Rditor Controllers to zone refer to Section 8: Chnging the Configurtion. 3 b b c Note: Zone number lbel Turn the locking knob nd seprte the operting module from the coupling module. Turn the coupling module wheel nticlockwise (pprox. 3 rottions) until the nose b reches the end stop c. Fit the coupling module to the TRV body b nd tighten by hnd. For Adptors see below Instll btteries into the operting module. Note: Check correct polrity. Fit the operting module onto the coupling module nd turn the locking knob down to lock in plce. When dption is complete the room temperture set-point is displyed. b c d e f g A selection of dptors re vilble to suit mny other TRV mnufcturers. For more informtion plese contct Honeywell Technicl Help Desk, detils on the bck pge. 5

6 Section 7: System Testing! Cution! When selecting the operting site ensure tht the distnce to wireless devices such s wireless hedphones, cordless phones etc. is pprox. -m. It is recommended to complete the system testing before mounting the wll brcket on the wll. Position the CM67z Room Unit s close s possible to the loction where it will be used. Wll Wll Wll Ceiling = Signl Strength Mx. Signl Length 30 meters Typicl exmple of Building Fbric Signl losses CM67z Room Unit to HR80UK Rditor Controllers. Move the CM67z slider to position.. Set the zone setpoint to 5 C by pressing the button. Press the button nd set the zone setpoint to 30 C by pressing the button. 3. Check ll the HR80UK s in zone received 5 C setpoint nd the ones in zone 30 C setpoint (llow 4 minutes for the HR80UK to receive the setpoint). Repet the steps nd 3 selecting different temperture vlues. 4. To complete the system test move the CM67z slider to the position then bck to the position. Instll the wll brcket for the CM67z (if required). HR80UK Rditor Controllers to HC60NG. Move the CM67z slider to position.. Set both zone nd zone setpoints to 5 C by pressing the button (Using the button to switch between zones). 3. Set ll HR80UK dils to the position. Set the dil of the first HR80UK to the ON position. The green LED on the HC60NG should come on. 4. Set the dil bck to the position nd ensure tht the green LED on the HC60NG boiler controller goes off. 5. Repet the steps 3 nd 4 with ll the HR80UK s in the system. 6. To complete the system test reset ll of the HR80UK rditor controllers bck to norml opertion by removing nd re-inserting the btteries on ech one. Instll the wll brcket for the CM67z (if required). Test between CM67z & HR80UK. CM67z room unit cn send test signl to the HR80UK rditor controllers nd the HC60NG boiler or zone vlve controller.. Set the CM67z slider to the position. Press the, nd buttons together to enter the test mode. The CM67z will disply: 6 The first two digits in the HR80UK disply indicte the number of received test messges, nd the right-hnd digit indictes the field strength ( = sufficient field strength, 5 = very good field strength). The red LED of the HC60NG indictes the field strength by mens of flshing ( = sufficient field strength, 5 = very good field strength). To dectivte Service mode: Press the binding procedure button for 5 seconds or wit 5 minutes or remove nd then re-insert the btteries. The green LED on the HC60NG will flsh once every 7 seconds. 7. Service mode The wireless contct between the rditor controller, the centrl operting unit nd receiver unit is checked in Service mode. This mode is for instller use only. Test between HR80UK & HC60NG. Seprte operting unit from coupling module (see Section 6). Turn the djustment dil until on (open) ppers in the disply. 3. Turn djustment dil two full rottions (70 ) further until test is displyed. Service mode is ctive. The rditor controller trnsmits test messge to ny vilble HC60NG. The field strength is indicte by the number of flshes of the red LED ( = sufficient field strength, 5 = very good field strength). 4. Press the binding procedure button (pge 8 - digrm 5 ). The rditor controller is redy to receive the test messge from the centrl operting unit.

7 AM PM 8. Prmeters of the CM67z Room Unit Instllers Set Up Mode llows chnging the controllers prmeters to meet specific ppliction requirements or customers needs. See fig to 7 how to enter the Instller set-up. Move the CM67z slider into the position. Press nd hold the nd 3 & 4 buttons together. 3 Press or to 4 chnge fctory setting. The disply will flsh indicting tht chnge hs been mde. 5 6 Press + or - to go to the next prmeter nd follow steps 3 & 4 to 7 mke chnges Section 8: Chnging the Configurtion Instller Set-Up Number (Press + or - to chnge) e.g. = AM/PM Ctegory Instller Set-Ups Press the button to confirm the chnge is ok. The disply will stop flshing indicting tht the new vlue hs been stored. Abbrevited Set-Up Description e.g. CL = Clock Disply Adjust other settings using the Instller Prmeter List below. To exit the Instllers Set-Up Mode move the CM67z slider to the position. Fctory Setting or New Choice (Press or to chnge) e.g. 0 = 4hr e.g. = hr AM/PM Instller Set-Up Mode Selected Prmeter list Prmeter Identifier Rnge Defult Ctegory AM-PM/4h select :CL 0 (4h) / (h) 0 (h) Reset time/temp progrm :rp 0 (user prog) / (fctory prog) 0 (user prog) You must now press the key to enter the 3:Cl next section Minimum ON time 3:Ot () 5 min CM67 Room Unit Internl Temperture Sensor Enble 6:tS 0 (disbled) (enbled for disply only) (enbled for disply nd control) 0 (disbled) Pump exercise feture enble 7:PE 0 (disbled) / (enbled) 0 (disbled) Cycle Rte 8:Cr {3,6,9} cph 6 cph System Timing Mster 9:Sn 0 (disbled) / (enbled) 0 (disbled) Upper Setpoint Limit 0:UL () C Lower Setpoint Limit :LL 5 () 0 5 C Temperture Offset :to -3.0 (0.5) K Proportionl Bnd Width 4:Pb.5 (0.5) 3.0.5K Optimistion enble 5:OP 0 (disbled) / (enbled) (enbled) Loss of Communictions Instruction 6:LC 0 (rely ) / (rely ON 0%) 0 (rely ) CM67z built-in temperture sensor use 7:SU 0 (HR80UK enbled) / (HC60NG enbled) / (both HR80UK nd HC60NG enbled) 0 (HR80UK enbled) HR80UK Window-Open Function 8:Ho 0 (disbled & ) / (enbled only) / (enbled only) / 3 (enbled & ) 0 (disbled & ) HR80UK Locl Override Function 9:HL 0 (disbled & ) / (enbled only) / (enbled only) / 3 (enbled & ) 3 (enbled & ) Automtic Summer/Winter Time Chngeover 0:tC 0 (disbled) / (enbled) (enbled) Reset Instller Mode Prmeters to Defults :FS 0 (modified) / (fctory) (fctory) 7

8 AM PM Section 8: Chnging the Configurtion (cont.) 8. Adding further HR80UK Rditor Controllers 3 c b b Turn the locking knob nd seprte the operting unit nd coupling module. Turn the coupling module wheel nticlockwise (pprox. 3 rottions) until the nose b reches the end stop c. Fit the coupling module to the TRV body b nd tighten by hnd. For Adptors see Section Binding Button Instll btteries into the operting unit. Note: Check correct polrity. Attch the pproprite Zone Lbel nd press the Binding Button. Softwre version is displyed nd the RF symbol flshes MAN MAN MAN MAN (Exmple Zone ) Repete for ll dditionl HR80 s to bind to this zone. Enter CM67z Binding Mode Move slider to position. Press nd hold, nd buttons together. Press MAN button to select zone or MAN to select zone MAN MAN Press signl. button to send the binding The HR80UK will disply RF symbol) during binding. (with no When complete the RF symbol will be displyed with the temperture setpoint (this cn tke up to 4 minutes). 8

9 AM PM AM PM Section 8: Chnging the Configurtion (cont.) 8. Binding HR80UK Rditor Controllers to the HC60NG Boiler Module MAN MAN MAN MAN 5 secs. To put the HC60NG in the listening mode press the button on the HC60NG for 5 seconds (Red LED flshes 0.5 sec on/off). Bind HR80UK Rditor Controllers to the Boiler Module :- Move slider to Position. Press nd hold Temp, nd Prog buttons together. Press the Holidy Button to select Boiler Tech-in Mode. Press to send Binding Signl. With successful tech-in the red LED will remin off (no longer flsh). 8.3 Built -in sensor configurtion The CM67z Room Unit fetures built-in temperture sensor used for specific pplictions. Sensor opertion is defined by prmeter 6:tS in Instller mode: 6:tS = 0 (Fctory defult. The built-in sensor is idle - not used for control nor mesurement). 6:tS = (The built-in sensor is used only for mesuring the room temperture) The symbol displyed next to the room temperture vlue indictes tht the sensor is used for mesurement only nd the temperture in the room is controlled by the HR80UK Rditor Controller. Due to different loctions of the CM67z Room Unit nd HR80UK Rditor Controller there my be difference between the setpoint displyed by the CM67z Room Unit nd the mesured temperture vlue. 6:tS = (The built-in sensor is used to mesure nd control the room temperture in zone or when zone vlve is used in zone ) The CM67z Room Unit must be locted in zone. To complete the configurtion you must set the 7:SU prmeter to decide which system components will use the temperture vlue from the CM67z Room Unit: 7:SU = 0 - HR80UK s only (fctory defult) 7:SU = - HC60NG (zone vlve controller) only, HR80UK s will use their own built-in sensor. 7:SU = - both HR80UK s nd HC60NG. 8.4 Adding HC60NG Zone vlve controller The HC60NG rely module cn lso be configured for controlling zone vlve. This is restricted to zone only. Before the binding procedure is strted the following CM67z Room Unit prmeters need to be set in order to control the zone tempertures vi the HC60NG s zone vlve controller: Enter the instller mode of the CM67z Room Unit nd set the instller prmeters: 6:tS =, 9:Sn =, 7:SU = or (see Built-in sensor configurtion).. Therml ctutor b. Zone vlve c. Zone vlve NOTE: Instll in ccordnce with locl wiring regultions Cution: Observe mbient temperture nd current limits (see HC60NG wiring lbel) Activting HC60NG Rely Module binding procedure Press nd hold the push button of the HC60NG Rely Module for 5 sec to enter the binding mode. The red LED will flsh t 0.5 sec on/0.5 sec off. Activte the binding procedure t the CM67z Room Unit s described in section 8. for zone. When binding informtion is received correctly the red LED of the zone vlve controller will be switched off. 8.5 Resetting Bound HR80UK 3 B i n d i n g Button Turn the locking knob nd seperte the operting unit nd coupling module. Lift bttery cover nd remove one of the btteries. 9 Press nd hold the Binding Button while reinserting the bttery. Now follow steps 5 to on pge 8.

10 Section 9: Trouble Shooting 9. Trouble Shooting Guide Symptom (Fult Messge) During Binding After binding procedure the symbol on HR80UK disply is off. After binding procedure the red LED of the HC60NG is on nd the green one is flshing once every 3 sec. After binding procedure the red LED of the HC60NG is on nd green LED is flshing twice every 3 sec. After binding procedure the red LED of the HC60NG is on nd green LED is flshing 3 times every 3 sec. After binding procedure the red LED of the HC60NG is on nd green LED is flshing 4 times every 3 sec. During Testing HR80UK does not receive the correct setpoint from the CM67z. The boiler does not switch on when the HR80UK setpoint is set to ON. HC60NG s green LED is not flshing every 5 sec during the system test During Norml Opertion The red LED of the HC60NG is on. The red LED of the HC60NG is flshing.5 sec on/.5 sec off. The CM67z shows different ctul temperture thn the HR80UK setpoint Blnk disply on CM67z or HR80UK. CM67z disply shows flshing bttery symbol ( ). CM67z displys spnner symbol ( ). Possible Cuse Incorrect or incomplete binding procedure. Bd position of the CM67z during binding. Incorrect or incomplete binding procedure. Bd position of the CM67z during binding. An ttempt ws mde to bind more thn 4 CM67z units to the HC60NG. An ttempt ws mde to cross bind the HC60NG with system timing messge when no other binding ws present. An ttempt ws mde to bind two system timing messges to one HC60NG. Bd position of the CM67z. No binding dt in the HR80UK. HR80UK bound to the wrong zone. Missing binding dt in the HC60NG. Bd position of the CM67z. The HC60NG receives no messges: RF signl is blocked (e.g due to bd position of the CM67z) or CM67z nd HR80UK btteries re exhusted. The HC60NG hs not received signls from one (or more) trnsmitters in the system but still receives signls from other trnsmitters: RF signl is blocked (e.g due to bd position of the CM67z) or CM67z nd HR80UK btteries re exhusted. Loction of HR80UK nd CM67z No btteries. Wrong bttery orienttion. Improper bttery comprtment insertion (CM67z only). Exhusted btteries. Btteries need replcing. Fult in the CM67z room unit. 0 Remedy Repet the binding procedure following the instlltion instructions. Repet the binding procedure keeping pprox. m distnce between CM67z nd HR80UK. Repet the binding procedure following the instlltion instructions. Repet the binding procedure keeping pprox. m distnce between CM67z nd HC60NG. Press nd hold the HC60NG push button for 5 sec to reset the memory. Repet ll the binding opertions for this HC60NG mking sure tht no more thn 4 CM67z units re bound. Reset the HC60NG binding dt by pressing the push button for 5 sec. Repet the complete strt up procedure s described in Section 8.: Chnging the Configurtion. Mke sure tht only one CM67z is configured s system timing mster. Reset the HC60NG binding dt by pressing the push button for 5 sec. Repet the complete strt up procedure s described in Section 8.: Chnging the Configurtion. Reposition the CM67z nd repet the test. Repet the binding procedure. Repet the binding procedure, mking sure tht the HR80UK is bound to the proper zone. Repet the binding procedure (CM67z with the HC60NG boiler controller or HC60NG zone vlve controller). Reposition the CM67z nd repet the test. Return the CM67z room unit to the position where communictions is relible or replce dischrged btteries. Return the CM67z room unit to the position where communictions is relible or replce dischrged btteries. Link the ctul temperture mesured by the CM67z with the HR80UK (only Zone cn be configured). Check tht the btteries re in the bttery comprtment nd tht the pper tb (CM67z only) hs been pulled out. Check tht the btteries hve been instlled in the correct orienttion. Remove bttery comprtment nd re-insert. Replce the btteries. Replce the btteries. Remove nd re-insert the bttery comprtment. If the spnner symbol ( ) does not cler itself in few minutes cll the Honeywell Technicl Help-Desk, detils on the bck pge.

11 Section 9: Trouble Shooting (cont.) 9. Trouble Shooting Guide (cont.) Symptom (Fult Messge) During Norml Opertion CM67z disply works but heting does not switch on: The HC60NG LEDs re The HC60NG green LED is ON HC60NG red LED is constntly ON or flshing. The HR80UK disply is blnk or shows batt. The ( ) symbol on the HR80UK is not displyed. Possible Cuse No power to HC60NG. Bd electricl connection to the boiler or fulty boiler. RF communiction lost due to bd loction of the CM67z room unit. RF communiction fult. HR80UK btteries exhusted. RF communiction lost due to bd loction of the CM67z room unit. RF communiction fult. Remedy Check the power to the HC60NG is on. Check the boiler nd HC60NG power supply s well s electricl connection between the boiler nd HC60NG. Hook the room unit bck on the wll brcket or return the room unit on the tble stnd to the position where communiction ws relible. Cll the Honeywell Technicl Help-Desk, detils on the bck pge. NOTE: The boiler cn be controlled mnully when RF communiction is lost. Press the HC60NG push button to switch the boiler on or off. When the green LED is on - the boiler is on. Replce the HR80UK btteries following the guidelines in the HR80UK user instruction. Hook the room unit bck on the wll brcket or return the room unit on the tble stnd to the position where communiction ws relible. Cll the Honeywell Technicl Help-Desk, detils on the bck pge. 9. Mnul dption Mnul dption cn be used to solve vrious problems: if utomtic dption does not work. if the entire vlve lift is to be utilized. if the rditor hrdly gets wrm t ll. if the rditor does not become cold. if the symbol is displyed (no dption possible). if the symbol is displyed (vlve lift too short or motor cnnot be moved). 9.4 Resetting the HR 80 to the fctory settings Seprte operting unit from the coupling module (Fig. ). Remove the btteries. Insert the btteries gin while keeping the binding procedure button pressed. Attch the operting unit to the coupling module (Fig. ). 9.3 Def (defult setting) nd Full operting modes In order to chnge between the two operting modes, press the binding button until the respective operting mode is shown on the disply. Binding Button Turn the locking knob nd seperte the operting unit nd coupling module. Def (defult setting) operting mode The HR 80 opertes with the optimum vlve lift tht is required for room temperture control. Full operting mode If the complete vlve lift is to be used or if the vlve does not close completely, you hve to set the HR 80 to the full operting mode. The bttery lifetime is reduced in the full operting mode. Attch the operting unit to the coupling module nd turn the locking knob

12 Environmentl Note: This product hs been designed with your environment in mind! Plese respect this by disposing of ll pckging nd used prts in n environmentlly friendly mnner. Do not dispose of btteries with household wste. They must be returned in ccordnce with the locl sttutory requirements. Wrning: This product nd its ssocited documenttion nd pckging re protected by vrious intellectul property rights belonging to Honeywell Inc nd its subsidiries nd existing under the lws of the UK nd other countries. These intellectul nd property rights my include ptent pplictions, registered designs, unregistered designs, registered trde mrks, unregistered trde mrks nd copyrights nd lso include the following UK registrtion rights: UK ptent ppliction number UK registered design numbers , nd Hereby, Honeywell, declres tht this CM67z is in complince with the essentil requirements nd other relevnt provisions of Directive 999/5/EC, 73/3EC nd 89/336EC. HC60NG Rely Module CM67z Room Unit HR80UK Rditor Controllers Useful References: - Honeywell UK website - CM Zone website Technicl Help-Desk: Honeywell reserves the right to modify this document, product nd functionlity without notice. This document replces ny previously issued instructions nd is only pplicble to the products described. Note: This Product hs been designed for pplictions s described within this document, for use outside of the scope s described herein refer to Honeywell for guidnce. Honeywell cnnot be held responsible for misppliction of the products described within this document Honeywell Control Systems Ltd. Honeywell House Arlington Business Prk Brcknell Berkshire RG EB R3