Model : SP601-15, 15T, 20, 20T, 30, 30T

Transcription

1 SP601 User Guide.pdf Bklet Part Number Q th Nvember 2005 User s Guide Mdel : SP601-15, 15T, 20, 20T, 30, 30T Spa-Quip Australia Pty Ltd Spa-Pwer Equipment service@spa-quip.cm.au Ph: Fax: Unit 2 13, Hyle Avenue Castle Hill NSW 2154 Australia Spa-Quip Ltd Spa-Pwer Equipment service@spa-quip.c.nz Ph: Fax: Rthwell Ave Nrth Harbur Industrial Park, Auckland NZ

2 Cntents Sectin Page 1 SP601 Tuch Pads...Pg 1 2 Temperature Cntrl... Pg Adjusting Set Temperature... Pg Nn Default Display Value... Pg Heating Mde Selectin(24hr circulatin pump nt fitted)... Pg 2 3 Pump Operatin... Pg Pump 1 (Single speed pump, n 24hr circulatin pump fitted)... Pg Pump 1 (Single speed pump, 24hr circulatin pump fitted)... Pg Pump 1 (Tw speed pump,n 24hr circulatin pump fitted)... Pg Pump 1 (Tw speed pump, 24hr circulatin pump fitted)... Pg 4 4 Auxiliary/Air Buttn... Pg Adjustable Speed Mde(SPVSB nly)... Pg 5 5 Operatin... Pg Adjustable Clur Mde(SPVCL nly... Pg IndicatrLlight... Pg 6 6 Aut Sanitisatin... Pg N 24hr Circulatin Pump Fitted... Pg Adjusting Minimum Filtratin... Pg Clean Up Cycle... Pg hr Circulatin Pump Fitted... Pg My Spa Is T Ht In Summer... Pg 7 7 Sleep Timer... Pg T Set Current Time And Day... Pg T Set Prgrams...Pg 8 8 Self Diagnstic Errr Cdes... Pg 9 8 Self-Diagnstic Errr Cdes The Spa Pwer 601 cntrller has extensive self diagnstic capabilities. In the event f a prblem it will indicate an errr number accrding t the nature f the prblem. The errr numbers and their meanings are listed belw. Nte: When in an errr state the alarm can be muted by pushing the/aux buttn. Errr 1 (H20) - Prime Failed This is nt necessarily a prblem with the SP601 itself, but indicates that n water is being detected in the heater husing. Prime failed is a special case in that it can be recvered frm by pushing a buttn. A push f the pump buttn will run the pump fr 10 secnds t try t get water t the heater. If successful nrmal peratin will resume. If unsuccessful, Errr 1 (H20) will be indicated n the display again. With any Errr 3-8, spa peratin will stp and nt cntinue until the cntrller is reset. The cntrller can nly be reset by pushing the UP, DOWN and buttns simultaneusly. The cntrller will remain in an errr cnditin even when reset at mains pwer, cntrller will nly cntinue nrmal peratin after the UP, DOWN and buttns are pushed simultaneusly (see belw). Up Buttn Errr 3 - Stuck Buttn E.6 ER Up Buttn Dwn Buttn Pump Buttn Dwn Buttn E.6 Pump Buttn This errr indicates that ne f the buttns in the tuchpad is stuck r has been held dwn fr mre than ne minute. This may be caused by the pl cver pressing n the tuchpad r by water getting int the tuchpad r by damage t the tuchpad r its cable. Try t reset the spa. If there is still a prblem then cntact yur spa pl supplier. Errr 4 - N Water Sensr This errr indicates a prblem with the ptical water sensr in the heater. The prblem may by caused by the sensr being discnnected r by damage t the sensr. Try t reset the spa. If there is still a prblem then cntact yur spa pl supplier. Errr 5 - Overtemperature This errr indicates that the digital temperature sensr in the heater r pl has detected a temperature f 45 C r mre. This may nt be a prblem with the SP601, it may be caused by excessive pump use in ht weather, r pump failure. Turn ff the spa and allw time fr the water t cl. If there is still a prblem then cntact yur spa pl supplier. Errr 6 - Thermal Cut OutTripped This errr indicates that the safety electrmechanical ver temperature cut ut n the heater has perated. This is nt necessarily a prblem with the SP601. It may have ccurred frm an air lck arund the element, high temperatures during shipping, r failure f the pump. This autmatic cut ut will nly reset nce the element has cled belw abut 38 C. The unit must then be reset befre it will resume peratin. Manually push the UP, DOWN and buttns simultaneusly. Errr 7 - Stuck Relay This errr indicates a prblem with the heater cntrl circuitry inside the unit. Cntact yur spa pl supplier. Errr 8 - NTemperature Data This errr indicates a prblem with the digital temperature sensr in the heater r pl wall r that bth the in heater and in pl sensrs are cnnected. Check that nly ne sensr is cnnected and that it has nt becme discnnected r damaged. Try t reset the spa. If there is still a prblem then cntact yur spa pl supplier. Page 9

3 7 Sleep Timer (Optinal Timeclck) If the ptinal time clck has been fitted, sleep mde is used t disable autmatic temperature maintenance and filtratin in rder t silence the spa pl during yur hurs f sleep. The sleep time setting is dne using the digital time clck n the frnt f the cntrl bx (See belw fr setting instructins). If M 9:3139 the spa is in use it will nt enter sleep mde until 30 minutes after the last OFF P manual buttn push, even if the clck is calling fr sleep mde. The spa can MANUAL still be used manually within sleep mde times as nrmal. On wake up frm sleep the system will run the blwer fr 15 secnds t purge the blwer plumbing. This prevents any stagnant water frm cllecting in the pipes if the pl is nt used fr an extended perid. 7.1 T Set Current Time and Day 1. Press the RESET buttn befre use. NOTE: This is ptinal. It will clear the current time and prgram settings. 2. Hld dwn the CLOCK buttn and press the DAY buttn until the crrect day is selected. Release bth buttns. 3. Hld dwn the CLOCK buttn and press the HOUR buttn until the crrect hur is set. Release bth buttns. 4. Hld dwn the CLOCK buttn and press the MIN buttn until the crrect minute is set. Release bth buttns. 5. After setting the weekday and time, the secnds will reset autmatically and the clck will begin keeping time. 7.2 T Set Prgrams 1. Press the TIMER buttn. "1" will appear at the left side f the display. This is the start time f the first prgrammed sleep blck (the time yu want the spa t enter the sleep mde). 2. Press the DAY buttn t select the days n which this sleep prgram will perate. There are 15 settings t chse frm. 3. Press the HOUR buttn t set the hur f the desired time t enter sleep mde. 4. Press the MIN buttn t set the minutes f the desired time t enter sleep mde. 5. Nw the start time has been set, press the TIMER buttn again. "1OFF" will appear n the display. This is the end time f the first prgrammed sleep blck (the time yu want the spa t resume nrmal peratin). 6. Repeat the same prcedure (2 t 4 abve) until the "1OFF" time is set.( Be careful t set the same days as used in the "1" time). 7. Yur timer gives yu up t 8 different prgrammable perids. Yu can use all 8 settings, r as few as yu like. 8. T Review yur set prgrams press the TIMER buttn and keep pressing it t advance thrugh each setting. IMPORTANT NOTE: The "MANUAL" buttn n the clck can be used t verride the prgrammed sleep settings. It is very imprtant t ensure that the clck is set t "" s that the prgrammed times can perate. If the clck is manually set t then the pl will stay in sleep mde and THE WATER WILL GO COLD. If it is left in "OFF" then the pl will nt enter the sleep mde. The clck des nt return t "" by itself. NOTE: If the MANUAL buttn n the clck is used the spa will nt return t the prgrammed settings until the next prgrammed time after being returned taut. Safety Ntes Befre using ensure that the spa pl has been cnnected t a suitable weather prtected utlet scket, equipped with a duble ple islating switch, which is f the crrect rating and cmplies with the lcal wiring regulatins. When installing refer t yur lcal wiring cde. In particular refer t ECP 2 & ECP 25 (AS / NZ) and EN & EN (EU). The system must be installed in such a way that live parts are nt accessible by a persn in the pl. If a supply crd is nt fitted the system must be permanently cnnected t fixed wiring thrugh a 30mAr less RCD. This appliance is nt intended fr use by yung children r infirm persns withut supervisin. Yung children shuld be supervised t ensure they d nt play with the appliance. Page 8 CLOCK TIMER DAY HOUR MIN Cngratulatins n chsing the latest Spa Pwer 601 cntrl system. This cntrller makes use f the latest technlgy, including innvative ptical and digital sensr designs. The greater variety f ptinal accessries, userfriendly tuchpad and reliable cmpnents prvide yu with the mst sphisticated cntrller in its class. 1 SP601 Tuch Pads Aux/Air LED Heat LED Pump LED Aut/H20 LED ER Pump Buttn Up Buttn Heat LED Pump LED Aut/H20 LED Aux/Air LED Dwn Buttn Up Buttn Aux/Air/Pump Buttn Pump Buttn Dwn Buttn Aux/Air/Pump Buttn Aut LED (N 24hr circulatin pump fitted) The yellw r blue Aut indicatr light will appear n the tuch pad whenever the system is in full autmatic cntrl mde. In this mde the system autmatically activates the pump and heater t filter the water and maintain the set water temperature. If this light is flashing the water sensr is nt detecting any water. H20 LED (24hr circulatin pump fitted) The yellw r blue H20 light indicates if water is present in the heater. If n water is detected then the LED will flash and the unit will nt perate except t run the circulatin pump t try t get water t the heater. If n water reaches the heater fr ne minute then an H20 errr will ccur. If this happens then pushing the pump buttn will run the circulatin pump fr anther minute. Pump LED The green Pump indicatr light will appear n the tuch pad whenever the pump is running, in bth aut and manual use mde. If this light is flashing, the spa is in Sleep Mde. Heat LED The red Heater indicatr light will appear n the tuchpad whenever the heater element is n, in bth aut and manual use mde. Fr safety the heater is always autmatically cntrlled. Usually switching n the air blwer accessry will cause the heater t switch ff (ladshedding). This is in rder t keep the ttal pwer lad t a safe level. If this light is flashing the system has an errr (see sectin 8). Aux/Air LED The Aux/Air indicatr LED will appear n the tuchpad whenever the Aux/Air buttn is pushed and cnversly will disapear when the buttn is pushed again. Nte: If the spa des nt have a lad cnnected t the cntrller the LED will still perate as described abve. Page 1

4 2 Temperature Cntrl The Spa Pwer 601 autmatically cntrls the pump and heater t filter the water and maintain it at the desired temperature set by the user (see belw).the user can leave the system t lk after the spa and knw it will be at the crrect temperature whenever he r she wants t use it. 2.1 Adjusting Set Temperature The Spa Pwer 601 gives the user direct cntrl f the pl temperature frm the plside cntrl panel. Hlding dwn the Up r Dwn buttn will adjust the temperature set pint as shwn n the digital readut. There is a slight delay befre the buttns perate t reduce the risk f accidental adjustment. The pl temperature will be maintained very clse t the set temperature. Default Display Page 2 UP Increase the set temperature by 0.5 C per beep (Max = 41.5 C) DOWN Decrease the set temperature by 0.5 C per beep (Min = 10.0 C) The display nrmally shws the temperature set pint, unless the ptinal in pl temperature sensr is fitted in which case the sensed water temperature is displayed. In either case the temperature set pint will be displayed while being adjusted as described abve. 2.2 Nn-Default Display Value The nn-default display value (either sensed water temperature r temperature set pint) can be checked if necessary by pressing the Up & Dwn buttns simultaneusly. Press bth buttns simultaneusly 2.3 Heating Mde Selectin (24hr circ pump nt fitted) In additin t the temperature setting the user can select the preferred heating mde. The tw available heating mdes are... 1/ Demand Heating (displayed as Ht.d).This is the default setting in which the pump and heater will cme n autmatically whenever the temperature drps slightly belw the set pint. 2/ Filtratin Only Heating (displayed as Ht.F).In this mde the pump and heater will cme n autmatically n mre than nce per hur t filter and heat the water. This mde is prvided as an ptin fr thse wh prefer t limit the natural cycling f the system. T select the heating mde first press the Pump and Dwn buttns simultaneusly t display the current heating mde, then press and hld the Up r Dwn buttns t change mdes. Press bth buttns simultaneusly ER Press Up r Dwn buttns t tggle between heating mdes. ER ER 6 Aut Sanitising (Filtratin) 6.1 N 24hr Circulatin Pump Fitted The Spa Pwer 601 autmatically maintains the filtratin/sanitising f the spa pl water. The minimum amunt f filtratin time is prgrammable by the user and can be adjusted between 0 and 15 minutes per hur (0 t 6 hurs per day). In rder t maintain crrect filtratin f the pl water, the SP601 mnitrs the time fr which the pump runs in nrmal pl peratin. If the pump has nly run fr a shrt time, the system will autmatically run the pump fr an additinal perid every hur t reach the minimum filtratin time set by the user Adjusting Minimum Filtratin Time (N 24hr circulatin pump fitted)) First push the Dwn andair/aux buttns tgether t display the filtratin time setting n the digital readut Press bth buttns simultaneusly ER Press bth buttns simultaneusly The default setting is 10 minutes per hur (= 4 hurs per day). Hlding dwn the Up Buttn r Dwn Buttn will adjust the filtratin time setting between 0 and 15 minutes per hur. (= 0 t 6 hrs per day) Clean Up Cycle If desired, a clean up cycle can be initiated t filter the water after the spa pl has been used. This is dne by simply pushing the Pump Buttn t leave aut mde and switch n the pump. This will circulate the water thrugh the filter fr 90 minutes. After 90 minutes the system will return t aut mde and maintain the temperature ready fr the next time the spa pl is used hr Circulatin Pump Fitted The Spa Pwer 601 cntinuusly filters the spa pl t ensure the water is clean and crystal clear fr each and every spa use. A near silent energy efficient circulatin pump cnstantly passes water thrugh the filter and since the circulatin pump runs all the time (except fr when the time clck has been set t sleep r in an errr cnditin) and the heater is cntrlled autmatically there is n need fr any user cntrls fr these features. With a 24hr circulatin pump fitted there is n need t prgram any filtratin cycles, and the nise f a large jet pump running during filtratin has been remved. 6.3 My Spa Is T Ht In Summer! During warm perids f the year there may be times when the actual water temperature exceeds the desired temperature set by the user. E.g. If the spa is set t heat t 35 C, but the actual water temperature is htter than 35 C. Please cnsider this - In the winter yur spa gets cld because the air temperature is cld. T cmbat this we heat the water and keep the spa cvered when nt in use. If the spa is turned ff and the ambient temperature is 15 C, eventually the spa water will lse heat until it t is 15 C. In the summer the same applies but in reverse - yu can turn the heater dwn, even turn the pump ff, but if the ambient daytime temperature is 35 C - 42 C then the spa water will als remain at that temperature. Manufacturers make n attempt t supply a system that cls water. The quickest way t cmbat the prblem is t change the water, but even this new water will eventually heat up t the air temperature. Turn the set temperature dwn s the heater des nt cme n. Reduce the minimum filtratin time (nn circ pump mdels nly) s the pump runs less. The less the pump runs the mre the water will cl. If the nighttime temperature is lw, leave the cver ff the spa t let heat escape, but put it back n during the day t keep heat ut. If the ptinal timeclck is fitted increase the sleep time perid therwise turn the spa ff vernight. Als make sure the spa is shaded frm direct sunlight. Page 7

5 5 Operatin Yur spa may have been fitted with either f tw different LED lights; a Spa Pwer Clured (SPCL) r a Spa pwer Variable Clured (SPVCL). The Spa Pwer Clured is a single clured light that is either n r ff. The Spa Pwer Variable Clured light is a light that has the ability t change between 12 different clurs and white (see belw fr user instructins). The multi-functin Buttn is used t turn the light n and ff (SPCL) and select thrugh the different perating mdes f the Spa Pwer Variable Clur. Tw shrt presses f the buttn will turn the Spa Pwer Clured n and ff r five shrt presses f the buttn will cycle the Spa Pwer Variable Clured as fllws: Buttn Push 1 - (SPCL - On) (SPVCL Clur - White) 3 Pump Operatin There are fur pssible variatins f pump 1 that may have been fitted t yur spa, this user guide cvers all variatins f pump 1 that culd have been fitted. Please read sectins 3.1 thrugh t 3.4 then fllw the sectin which matches yur spa peratin. Nte: Even if a 24hr circulatin pump is fitted there is n buttn t cntrl it. The 24hr circulatin pump peratin is cmpletely autmatic, It nly turns ff in sleep mde (if ptinal time clck is fitted) r in an errr cnditin. 3.1 Pump 1 (Single speed pump, n 24hr circulatin pump fitted) Pump 1 is cntrlled by just ne tuch pad buttn pushing the pump buttn three times cycles its peratin thrugh three mdes Autmatic, Manual and Standby. When the spa is running in autmatic mde, pressing the pump buttn will deactivate aut mde and set the pump running in Manual Mde. The aut LED is range when aut mde is enabled and ff when in Manual Mde. When the pump is in standby mde all indicatr LED's are ff. Push 1 (Manual Mde) Push 2 - ADJUST (SPCL - Off) (SPVCL Adjustable Clur Mde) Push 3 - CYCLE SLOW Push 4 - CYCLE FAST (SPVCL Cycle thrugh clurs - slwly) (SPVCL Cycle thrugh clurs - quickly) Push 2 (Standby Mde) Push 3 (Aut Mde) Push 5 - OFF (Default State) Nte: This is a multi-functin buttn which perfrms the fllwing - 1) Shrt presses f this buttn activate the light functins as detailed abve. 2) Hlding this buttn will begin t increase the set temperature f the spa. 3) When a Spa Pwer Variable Speed Blwer is fitted and is turned n this buttn increases the blwer speed. 5.1 Adjustable Clur Mde (SPVCL nly) When the light is n, shrt presses f the Dwn buttn will put the light int adjustable clur mde and then sequentially select thrugh all the available clurs. The last clur set in this mde will be remembered the next time the light is used. 5.2 Indicatr A small red dt in the bttm crner f the digital readut indicates when the light is turned n. If left n the light will autmatically switch ff after 30 minutes. Ntes: 1) If Pump 1 is left in Manual r Standby mdes it will autmatically revert t Aut mde after 90 minutes. 2) There is n direct user cntrl ver the heater. The heater may cme n autmatically whenever Pump 1 is n. 3.2 Pump 1 (Single speed pump, 24hr circulatin pump fitted) Pushing the pump buttn tw times turns the pump n and then ff. The pump LED is green when the pump is running and ff when the pump is ff. Push 1 (Pump n) Push 2 (Pump ff) H20 H20 Ntes: 1) If Pump 1 is left n, it will autmatically switch ff after 20 minutes. 2) There is n direct user cntrl ver the heater. The heater may cme n autmatically whenever the 24hr circulatin pump is n. 3) If the heater element is n, running the pump may cause the heater t lad shed and switch ff. If this ccurs the heater will cme back n apprximately 5 secnds after the pump is deselected. Page 6 Page 3

6 3.3 Pump 1 (Tw speed, n 24HR circulatin pump fitted) Pump 1 is cntrlled by just ne tuch pad buttn pushing the pump buttn 4 times cycles its peratin thrugh 4 mdes Autmatic, Manual Lw Speed, Manual High Speed and Standby. When the spa is running in autmatic mde, pressing the pump 1 buttn will deactivate aut mde and set the pump running in Manual lw speed. The aut LED is range when aut mde is enabled and ff when in manual lw speed r manual high speed. When the pump is in standby mde all indicatr LED's are ff. 4 Auxiliary Air Buttn TheAir Buttn cntrls an auxiliary air blwer. It is used t turn the blwer n and ff, and select different perating mdes if a Spa Pwer Variable-Speed Blwer (SPVSB) has been fitted. 2 pushes (STD) r 4 pushes (SPVSB) f the air buttn cycles the blwer as fllws: Nte: In sme spas an additinal jet pump r pl light etc may be fitted instead f a standard air blwer. Push 1 (Manual Lw Speed) Standard Air Blwer (STD) Push 2 (Manual High Speed) Push 1 - Blwer Push 2 - Blwer OFF Push 3 (Standby Mde) Spa Pwer Variable-Speed Blwer (SPVSB) (if fitted) Push 4 (Aut mde) Push 1 - Blwer (Full Speed) Red Ntes: 1) If Pump 1 is left in Manual r Standby mdes, it will autmatically revert t Aut mde after 90 minutes. 2) There is n direct user cntrl ver the heater. The heater may cme n autmatically whenever Pump 1 is n. 3) If the heater element is n, running the pump in high speed may cause the heater t lad shed and switch ff. Push 2 - Blwer ADJUSTABLE (Adjustable Speed) Push 3 - Blwer OSCILLATING (Oscillating Speed) Orange Green 3.4 Pump 1 (Tw speed, 24HR circulatin pump fitted) Push 4 - Blwer OFF (Default State) N Pushing the pump buttn three times cycles the pump thrugh its tw speeds then ff. The pump LED is green when the pump is running in lw r high speed and ff when pump is ff. Nte: If left n, this accessry will autmatically switch ff after 20 minutes. If the heater element is n, switching n this accessry may cause the heater t ladshed and switch ff. This is t keep the ttal pwer lad t a safe level. Push 1 (Lw Speed) H Adjustable Speed Mde (SPVSB nly) Push 2 (High Speed) Push 2 (Pump ff) H20 H20 If a Spa Pwer Variable-Speed Blwer is fitted, the spa user has the ability t adjust the blwer speed t any desired setting. The Up and Dwn buttns are used t set the desired blwer speed. Nte: If the blwer is in Full Speed r Oscillating mdes then pushing the Up r Dwn buttn will put it int Adjustable Speed mde and then adjust the speed. Ntes: 1) If Pump 1 is left n, it will autmatically switch ff after 20 minutes. 2) There is n direct user cntrl ver the heater. The heater may cme n autmatically whenever the 24hr circulatin pump is n. 3) If the heater element is n, running the pump in high speed may cause the heater t lad shed and switch ff. If this ccurs the heater will cme back n apprximately 5 secnds after the pump is deselected. Step 1) Press Air Buttn twice t set Adjustable Speed Mde Step 2) Press Up t increase speed f blwer Step 3) Press Dwn t decrease speed f blwer turns t range Page 4 Page 5